602540
15
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
Assembly and installation 5
0020147164_04 aroTHERM Installation instructions 15
1. Insulate the lines (including those running below
ground) with UV-resistant and high-temperature-res-
istant insulation between the product and the heating
installation.
2. In order to avoid transferring vibrations to the surround-
ing buildings, use flexible connection pipes on the
product that have a length of at least 0.75 m.
3. When the product is not installed at the highest point in
the heating circuit, install additional purging valves in
suitable places.
4. Install the following accessories in the heating return.
Installation without decoupling hydraulic module
Drain cock
Air separator (if required)
Dirt filter
An expansion vessel suitable for the complete hydraulic
installation
Expansion relief valve 0.3 MPa (3 bar)
Pressure gauge (recommended)
Note
If you use glycol, you must collect it at the
expansion relief valve to prevent environ-
mental pollution.
0.75 m min.
1
4
5
6
7
3
2
1 Connection hose in the
heating flow to the building
(on-site)
2 O-ring seal
3 Covering cap
4 Heating flow connection
(diameter 1 1/4") to the
building
5 Heating return connection
(diameter 1 1/4") to the
heat pump
6 Connection hose in the
heating return to the heat
pump (on-site)
7 Insulation (on-site)
5. Remove the covering caps (3) from the product's hy-
draulic connections.
6. Install a dirt filter in the heating circuit return between
two stop valves so that the filter can be cleaned regu-
larly.
7. Install a flexible connection pipe (1) and (6) (to be
provided on-site) with an O-ring and a stop valve to
each of the connections for the heat pump heating flow
and return.
8. Check the connections for tightness.
5.3.2 Installing system diagram 8, variant E
1. Install the system in accordance with system diagram 8,
variant E ( Page 30).
Note
In this system, the circulation pump of the
heat pump functions as a heating pump. It
is also in operation when only the boiler is in
operation.
2. On start-up, set system diagram 8 on the controller.
3. In order to guarantee operation with two heat generat-
ors, install the flow temperature sensor.
4. Connect the eBUS-compatible boiler using a bus
coupler on the eBUS line.
5.3.3 Installing system diagram 8, variant F
1. Install the system in accordance with system diagram 8,
variant F ( Page 30).
2. On start-up, set system diagram 8 on the controller.
3. In order to guarantee a minimum circulation water
volume, install a differential-pressure bypass valve.
4. In order to guarantee the product's underfloor protective
circuit, install a limit thermostat.
5. In order to guarantee the hot water generation using the
heat pump, install a cylinder sensor and a 3-way valve.
5.3.4 Installing system diagram 10, variant B
1. Install the system in accordance with system diagram
10, variant B ( Page 30).
2. On start-up, set system diagram 10 on the controller.
3. In order to guarantee a minimum circulation water
volume, install a differential-pressure bypass valve.
4. In order to guarantee that the unit can be operated with
an auxiliary heating module, install the flow temperature
sensor.
5. In order to guarantee the hot water generation using the
heat pump, install a cylinder temperature sensor and a
3-way valve.
6. In order to guarantee the product's underfloor protective
circuit, install a limit thermostat.
7. Install an auxiliary electric heater on-site.
8. Set the hot water temperature for the pre-heating stage
on the system controller and the desired hot water tem-
perature on the on-site auxiliary heater.
5.3.5 Installing system diagram 12, variant A
1. Install the system in accordance with system diagram
12, variant A ( Page 30).
2. On start-up, set system diagram 12 on the controller.
3. Connect the area valves.
4. In order to guarantee a minimum circulation water
volume, install a differential-pressure bypass valve.
5. In order to guarantee the product's underfloor protective
circuit, install a limit thermostat.
6. In order to guarantee that the unit can be operated with
an auxiliary heating module, install the flow temperature
sensor.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vaillant aroTHERM VWL 85-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vaillant aroTHERM VWL 85-2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Vaillant aroTHERM VWL 85-2

Vaillant aroTHERM VWL 85-2 Gebruiksaanwijzing - Nederlands - 20 pagina's

Vaillant aroTHERM VWL 85-2 Gebruiksaanwijzing - Deutsch - 24 pagina's

Vaillant aroTHERM VWL 85-2 Gebruiksaanwijzing - English - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info