602543
27
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
Troubleshooting 8
0020147164_04 aroTHERM Installation instructions 27
Note
If necessary, you can drain the heating
installation using this drain cock by opening
the stop valves on the back of the heat
pump.
7.7 Checking the product's status codes
Menu Live Monitor
You can check the product's status codes at any time to see
which operating condition the heat pump is in. You can read
these codes on the display of the heat pump control module
or hydraulic station VWZ MEH 61.
7.8 Checking the electrical installation
Check the electrical installation and take all relevant dir-
ectives into account.
Checking the cable
If the product's mains power cable is damaged, then, in order
to avoid danger, only the manufacturer, the Customer Ser-
vice team or a similarly qualified person should replace the
mains power cable.
To replace the mains power cable, see Carrying out the
electrical installation ( Page 17).
7.9 Start-up following maintenance
1. After the maintenance work has been completed, start
up the product see Start-up ( Page 21).
2. If you have carried out work on load-bearing parts,
check that they are securely fitted.
3. When you have completed work on the product, carry
out an operational and safety test.
8 Troubleshooting
8.1 Troubleshooting
You should carry out the following tests before introducing
additional steps:
Make absolutely sure that the power supply was not cut
and that the product is correctly connected.
Ensure that the service valves are open.
Check that all external controllers are correctly connec-
ted.
8.2 Fault codes
The fault codes are described in a table in the Appendix.
Fault codes ( Page 48)
In the event of a fault, a fault code number is shown in the
controller's display.
Carry out all necessary repairs.
Switch the product on/off using the partition.
8.3 Carrying out the actuator test
Menu Installer level Test menu Sensor/actuator
test
You can check that the components of the heating installa-
tion are functioning correctly using the sensor/actuator test.
Display Test programme
T.0.01 Heating pump power
T.0.05 Fan power
T.0.07 4-way valve (circuits for thawing are not counted)
T.0.08 Position of the electronic expansion valve
T.0.09 Heating coil compressor
T.0.13 Flow temperature
T.0.14 Return temperature
T.0.15 Heating circuit pressure
T.0.16 Heating circuit flow rate
T.0.17 Lockout contact S20
T.0.66 Air inlet temperature
T.0.26 Compressor outlet temperature
T.0.27 Compressor inlet temperature
T.0.29 Heat exchanger temperature
T.0.30 High pressure
T.0.31 Condensation temperature
T.0.33 Evaporation temperature
T.0.34 Superheating target value
T.0.35 Superheating actual value
T.0.36 Subcooling actual value
T.1.37 Outside temperature
T.1.38 DCF status
T.1.59 Multi-function output 1
T.1.60 Multi-function output 2
T.1.61 Diverter valve 1
T.1.62 Flow sensor
T.1.63 Cylinder sensor
T.1.64 Multi-function input
T.1.65 Energy supply company input
T.1.66 Inlet temperature
T.1.67 High-pressure switch
T.1.68 Compressor rotational speed
T.1.69 Condensate pan heating
T.1.15 Water pressure
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vaillant aroTHERM VWL 155-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vaillant aroTHERM VWL 155-2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Vaillant aroTHERM VWL 155-2

Vaillant aroTHERM VWL 155-2 Gebruiksaanwijzing - Nederlands - 20 pagina's

Vaillant aroTHERM VWL 155-2 Gebruiksaanwijzing - Deutsch - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info