779591

VTech VM343 Handleiding

1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
User’s manual
Safe & Sound®
Pan & Tilt Video
Baby Monitor VM343
You can power up the parent unit by connecting
it to AC power or to the rechargeable battery
provided. Even if the parent unit is connected to
AC power, we recommend you also install the
battery. This guarantees continual operation in
case of a power outage.
Install the battery as shown below.
Press down on the large tab of the battery
compartment cover and pull it out.
1.
With the label THIS SIDE UP facing up,
insert the small tabs of the battery into the
slots inside the battery compartment. Make
sure the metallic contact is correctly oriented
as shown below. Push the battery into the
battery compartment until it clicks securely
into place.
Align the battery compartment cover flat
against the battery compartment, then slide
it towards the centre of the parent unit until it
clicks into place.
Replace the battery
To replace the battery, press down on the large
tab of the battery compartment cover and pull
it out, then follow the steps above to install the
battery.
NOTES
The operating time for using the rechargeable
battery is short. If you want to monitor your baby for
a long time, we recommend you connect the parent
unit to AC power.
If the parent unit will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
2.
3.
•
•
NOTES
Use only the battery supplied with this product.
Use only the power adaptors supplied with this
product.
Make sure the wall socket is switched on.
The power adaptors are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if
they are plugged into a ceiling, under-the-table or
cabinet outlet.
Make sure the parent unit, the baby unit and the
power adaptor cord are out of reach of children.
Connect the baby monitor
•
•
•
•
•
Charge the parent unit battery
When you have connected the parent unit
and installed its battery for the first time or
after power outage, the parent unit powers on
automatically. The battery icon indicates the
battery status (see the following table).
NOTES
The parent unit battery is fully charged after
3 hours of continuous charging.
It takes longer to charge the battery when the
parent unit is turned on. To shorten the charging
time, turn the parent unit off whilst charging.
The standby time varies depending on the
sensitivity level you set, your actual use and the
age of the battery.
Battery
indicators
Battery
status
Action
The battery
icon is off
and
displays.
No battery
is installed
but operates
using AC
power, or the
battery has
been installed
incorrectly.
Install the
parent unit
battery.
Charge without
interruption
(at least
30 minutes).
The screen
displays
Battery low
at Parent
Unit and .
The lightlight
flashes.
The battery
has very little
charge and
may be used
for only a
short time.
Charge
without
interruption
(about
30 minutes).
The battery
icon
becomes
solid .
The battery is
fully charged.
To keep
the battery
charged,
connect it to
AC power
when not in
use.
•
•
•
Test the baby monitor before initial use, and at
regular times thereafter.
To test your baby monitor:
Place the parent unit and the baby unit in the
same room to test the product. Make sure
the baby unit is at least 1 metre / 3 feet away
from the parent unit.
Slide ON/OFF on the baby unit to turn it on.
Upon initial use, the parent unit powers on
automatically after connecting to AC power.
The screen shows ® and Powering
on....
NOTE
If both units are not connected, the parent unit displays
No link to CAM 1 and Linking... on the screen. The
LINK light first flashes and then turns off. Move the
parent unit closer to the baby unit.
1.
2.
3.
Positioning the baby monitor
NOTE
This baby monitor is intended as an aid. It is not a
substitute for proper adult supervision and should not
be used as such.
CAUTION
Keep the baby unit out of the reach of your baby.
Never place or mount the baby unit inside the baby’s
cot or playpen.
Place the baby unit at least 1 metre / 3 feet
away from your baby.
2. Place parent unit at least 1 metre / 3 feet
away from the baby unit.
NOTE
If you experience audio feedback on either the parent
unit or baby unit, move the parent unit further away
until there is no more audio feedback.
TIP
You can increase the speaker volume of the parent
unit if you cannot hear the sounds transmitted from
the baby unit.
Operating range
The operating range of the baby monitor is up to
300 metres (1,000 feet) outdoors or 50 metres
(160 feet) indoors. The actual operating range
may vary depending on the environmental
conditions and other interferences such as
walls, doors and other obstructions.
1.
Baby unit overview
1Light sensor
2Infrared LEDs
3Camera
4Microphone
5Speaker
6Antenna
7Power jack
8Temperature sensor
9ON/OFF LED light
On when the baby unit is turned on
and is paired to the parent unit.
Flashes when the baby unit is pairing
to the parent unit.
•
•
10 ON/OFF switch
Slide to turn the baby unit on or off.•
11 -/VOL/+
Press to adjust the listening volume.•
12 Threaded socket
For wall mount installation use.•
Parent unit overview
1Speaker
2 Power jack
3Stand
4Antenna
5LED lights
Indicate the different statuses of
the parent unit. For details, refer to
Parent unit lights.
•
6Microphone
7 On/off
Press to power on.
Press and hold to power off.
•
•
8TALK
Whilst viewing an image,
press and hold to talk to the
baby unit.
•
9 Zoom
Whilst viewing an image, press to
zoom in or out.
•
Install the battery
Connect and charge the
battery
10
Whilst in a menu, press to select a
feature.
Whilst viewing an image,
press and hold to move the image to
the right.
•
•
11
Whilst in a menu, press to return to
the main menu or idle screen.
Whilst viewing an image,
press and hold to move the image to
the left.
•
•
12
Press and hold to turn the parent
unit screen off.
Press to skip to the next lullaby.
Press to play or stop the lullaby.
•
•
•
13 +/VOL
Press to increase the speaker
volume.
•
14 -/VOL
Press to decrease the speaker
volume.
•
15 MENU/SELECT
Press to enter the menu.
Whilst in a menu, press to choose
an item or save a setting.
•
•
16
Whilst in a menu, press to scroll up.
Whilst viewing an image,
press and hold to move the image
upwards.
•
•
17
Whilst in a menu, press to scroll
down.
Whilst viewing an image,
press and hold to move the image
downwards.
•
•
Parent unit lights
LINK On when moderate or high signal
strength is detected between the
parent unit and the baby unit.
Flashes when low signal strength is
detected between the parent unit and
the baby unit.
Off when the parent unit is turned off,
or the link to the baby unit is lost.
On when the parent unit is connected
to AC power, or the battery is charging.
Flashes when the parent unit battery is
low and needs charging.
Off when the parent unit is
disconnected from AC power.
TALK On when the parent unit is talking to
the baby unit.
On when the speaker volume of the
parent unit is turned off.
Parent unit display icons
Connection status
displays when strong signal
strength is detected between the
baby unit and the parent unit.
or displays when moderate
or low signal strength is detected
between the baby unit and the
parent unit.
displays when the link between
the baby unit and the parent unit
is lost.
•
•
•
Patrol mode
Displays when the parent unit is in
PATROL mode.
•
Night viewing
Displays when the camera has
activated the night viewing feature.
•
Zoom
Displays when the camera at the
baby unit has zoomed in.
•
Temperature alert
Displays when the temperature
alert is set on.
•
57 oF
or
14 oC
Real-time temperature
Displays the real-time temperature
of the baby unit.
•
Mute alert
Displays when the speaker volume
is set to off.
•
or
Sound level indicators
Displays the sound level according
to the scales of loudness when
there is sound transmitted from
the baby unit.
Speaker volume
Displays the speaker volume level
whilst adjusting.
•
•
Battery status
animates
when the battery is charging.
displays solid when the battery
is fully charged.
displays when the battery is
low and needs charging.
•
•
•
AC power
Displays when the parent unit is
connected to AC power without
the battery.
•
Parent unit main menu icons
Alert tone
You can set the parent unit to beep
when
the parent unit battery is low;
the link between the parent unit
and the baby unit is lost.
•
•
Sensitivity
With this feature, you can choose
to hear sounds from the baby unit
all the time, or to hear sounds that
exceed a certain level. You can
use the parent unit to adjust the
microphone sensitivity of your baby
unit. The higher the sensitivity level,
the more sensitive the baby unit is in
detecting sounds for transmitting to
the parent unit.
Temperature
You can turn the temperature
alert feature on so that the parent
unit beeps whenever the room
temperature detected by the
baby unit falls out of the desired
temperature range.
Vibration
You can turn the vibration alert on so
that the parent unit vibrates when
the link between the parent unit
and the baby unit is lost;
the temperature detected by the
baby unit falls out of the preset
temperature range.
•
•
Sound-activated screen
Automatically turns on the parent
unit screen when a sound is
detected in your baby’s room. When
no sound is detected, the screen is
off to save power.
Brightness
You can change the brightness of
the parent unit screen.
Rename
You can choose a specific name
for the baby unit from a pre-defined
name list.
Pair/unpair
The baby unit and parent unit
provided are already paired.
Parent unit display messages
No link to
CAM 1.
The baby unit is out of
range or is turned off.
Battery low at
Parent Unit
The battery level of
the parent unit is very
low and needs to be
recharged.
Battery empty.
Powering off ... The battery is empty and
needs to be recharged.
Temperature too
low at CAM 1.
The temperature detected
from the baby unit is
below the selected
minimum temperature.
Temperature too
high at CAM 1.
The temperature detected
from the baby unit is
above the selected
maximum temperature.
Powering on... The parent unit is turning
on.
Linking... The parent unit is
searching for baby unit
when the link is lost.
Using the baby monitor
Power the baby unit on or off
Slide ON/OFF to the left to turn the baby unit
on. The ON/OFF LED light turns on.
Slide ON/OFF to the right to turn the baby
unit off. The ON/OFF LED light turns off.
Power the parent unit on or off
Press to turn the parent unit on. The
LINK light turns on.
Press and hold again to turn the parent
unit off. The LINK light turns off.
Turn the parent unit screen on or
off
You can turn the parent unit screen on or off
without powering off the parent unit. You can
still hear sound from the baby unit.
Press and hold VIEW on the parent unit to
turn the screen off.
Press any key on the parent unit to turn the
screen on again.
Adjust speaker volume
For parent unit:
Press VOL+ or VOL- on the parent unit at
any time when viewing images.
NOTE
When the parent unit speaker volume is set to zero,
appears on the screen and the light turns on.
For baby unit:
Press VOL+ or VOL- on the baby unit at
any time.
•
•
•
•
•
•
•
•
1.
Adjust screen brightness
You can change the brightness of the parent
unit screen from Level 1 to Level 5.
Press MENU when the parent unit is not in
use.
Press or to choose BRIGHTNESS, then
press SELECT.
Press or to choose the desired level of
brightness, then press SELECT to confirm
your selection.
Adjust the sound sensitivity of
the baby unit
You can choose to hear sounds from the baby
unit all the time, or to hear sounds that exceed
a certain level. You can use the parent unit to
adjust the microphone sensitivity of your baby
unit from Level 1 to Level 5. The higher the
sensitivity level, the more sensitive the baby
unit is in detecting sounds for transmitting to the
parent unit. The sound sensitivity is preset to
Level 3.
1.
2.
3.
Sound sensitivity table for reference
Sensitivity Description
Level 5 High
sensitivity
Low
sensitivity
High sensitivity level
The parent unit speaker is
constantly on, and you will
hear all sounds (including
background noises) from
your baby’s room.
Level 4 Medium high
sensitivity level
The parent unit speaker
turns on for soft babbling
and louder sounds from your
baby. It remains quiet when
your baby sleeps soundly.
Level 3 Medium sensitivity level
The parent unit speaker
turns on for loud babbling
and louder sounds from
your baby. It remains quiet
when your baby makes soft
sounds.
Level 2 Medium low
sensitivity level
The parent unit speaker
turns on for crying and louder
sounds from your baby. It
remains quiet when your
baby makes soft sounds.
Level 1 Low sensitivity level
The parent unit speaker
turns on for loud crying or
screeching sounds from
your baby. It remains quiet
when your baby makes soft
sounds.
Press MENU when the parent unit is not in
use.
Press or to choose SENSITIVITY, then
press SELECT.
Press or to choose the desired
sensitivity level, then press SELECT to
confirm your selection.
TIP
You can adjust the baby unit placement to improve
the sound detection.
1.
2.
3.
Turn the sound activation on or
off
The parent unit continuously monitors the sound
level in your baby’s room. When the sound
activation mode is on, the parent unit screen
turns on when the baby unit detects a sound.
As long as no sound is detected within
50 seconds, the parent unit screen is off to
save power. When your baby starts to cry, the
sound activation triggers the parent unit screen
automatically turns on.
Press MENU when the parent unit is not in
use.
Press or to choose
SOUND-ACTIVATED SCREEN,
then press SELECT.
Press or to choose On or Off, then
press SELECT to confirm your selection.
NOTE
NOTES
If you mute the speaker whilst sound activation
is on, then you hear a beep sound whenever the
screen turns on.
If you want to turn the parent unit screen on
continuously whilst the sound activation is on, then
set the sound sensitivity to Level 5.
Zoom
You can zoom in or out whilst viewing an image
from the baby unit.
Press to zoom in.
Press and hold , , or to move the
zoomed image upwards, downwards,
leftwards or rightwards correspondingly.
Press again to zoom out.
Talk
You can use the TALK function of the parent
unit to comfort your baby.
Press and hold TALK on the parent unit. The
TALK light turns on.
Speak towards the microphone on the parent
unit. Your voice is broadcast to the baby unit.
Release the TALK key to stop the broadcast.
The TALK light goes off.
1.
2.
3.
•
•
•
•
•
1.
2.
3.
What’s in the box Before use Overview
123
123
a
b
d
e
f
g
h
i
j
k
l
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
a
b
c
At least 1 metre
(3 feet)
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VTech VM343 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VTech VM343 in de taal/talen: Engels als bijlage per email.

De handleiding is 3.31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info