809801

VTech LM808-2W Handleiding

2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Below are the questions most frequently asked about the baby monitor.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby unit and the parent unit.
2. Remove the batteries in the parent unit. Then, install the batteries again.
3. Wait a few seconds before connecting power back to the baby unit and the parent unit.
4. Turn on the baby unit and the parent unit.
5. Wait for the parent unit to synchronize with the baby unit. Allow up to one minute for
this to take place.
Why doesn’t the
baby unit and parent
unit power-on light
illuminate when the units
are switched on?
Perhaps the parent unit is not connected to the power. Insert the appliance plug into the
parent unit and insert the adaptor in a wall socket. Then, press and hold POWER to switch
on the parent unit and to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug into the
baby unit and insert the adaptor in a wall socket. Then, slide the ON/OFF switch to ON
to switch on the baby unit and to establish connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Check that the power jack is firmly inserted into the parent unit socket and the adaptor is
fully inserted in the wall socket. Make sure your power is not controlled by an electronic
wall switch.
Why is my screen in black
and white? The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors, like
lighting, objects, colours and backgrounds may affect the image quality on your parent
unit screen. Adjust the baby unit angle or place the baby unit at a higher level to prevent
glare and a blurry display.
Why does the baby
monitor produce
feedback?
The parent unit and baby unit may be too close to each other.
• Move the parent unit away from the baby unit until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent unit
beep? The baby unit may be out of range. Move the parent unit closer to the baby unit (but not
less than 1 metre).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit until battery icon becomes solid.
The temperature of your baby’s room may be too high or too low.
Why does the parent unit
react too quickly to other
sounds?
The baby unit also picks up other sounds than those of your baby. Adjust the VOX
sensitivity level to a lower level or lower the parent unit speaker volume.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
The parent unit speaker volume may be too low. Press to increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby
unit to set to a higher level.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby unit may be out of range. Move the parent unit closer to the baby unit (but not
less than 1 metre.
Other electronic and wireless products may cause interference with your baby monitor.
Try installing your baby monitor as far away from these devices as possible.
If you power on only one baby unit, your parent unit may display and No link to CAM #,
and the LINK LED light flashes. Press VIEW to switch to the baby unit you have powered on.
Frequently asked questions
If you are not going to use the baby monitor for some time, store the parent unit, the baby unit and the
adaptors in a cool and dry place.
Storage
1 LED lights
• Indicate the different statuses of
the parent unit. For details, refer to
Parent Unit Lights.
2LCD display
3VOL
4 VOL
5 Zoom
• Press to zoom in or out.
6VIEW / LCD ON/OFF
7Microphone
8POWER
9TALK
• Press and hold to talk to the selected
baby unit.
10
• While in a menu, press to return to
the main menu or idle screen.
• While viewing zoomed image,
press and hold to move the zoomed
image leftward.
11
• While in a menu, press to scroll up.
• While viewing zoomed image,
press and hold to move the zoomed
image upward.
12
• While in a menu, press to choose an
item.
• While viewing zoomed image,
press and hold to move the zoomed
image rightward.
13 MENU/SELECT
• Press to enter the menu.
• While in a menu, press to choose an
item, or save a setting.
14
• While in a menu, press to scroll down.
• While viewing zoomed image,
press and hold to move the zoomed
image downward.
15 Antenna
16 RESET
• Force reboot the parent unit.
17 Stand
18 Speaker
19 Power jack
EXIT
Parent unit overview
Parent Unit Lights
LINK • On when the parent unit is linked to
the baby unit.
• Flashes when the link to the baby
unit is lost.
• On when the parent unit is
connected to AC power, or the
battery is charging.
• Flashes when the parent unit
battery is low and needs charging.
• Off when the parent unit is
disconnected from AC power.
• On when the parent unit speaker
volume is set to off; or
• When the parent unit is talking to
the baby unit.
TALK • On when the parent unit is talking to
the baby unit.
19
The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark
room. When the baby unit being viewed detects low light levels, the infrared LEDs are
switched on automatically. The images from the baby unit are in black and white, and
appears on the screen.
Notes
• It is normal to see a short white glare on your parent unit screen as the baby unit adapts to the dark
environment.
• When the infrared LEDs are on, the images are in black and white.
Tip
• Depending on the surroundings and other interfering factors, like lighting, objects, colours and
backgrounds, the video quality may vary. Adjust the baby unit angle or place the baby unit at a higher
level to prevent glare and a blurry display.
Night vision
To keep this product working well and looking good, follow these guidelines:
• Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft damp cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under running water.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
General product care
Mount the baby unit on dry wall (optional)
Items to purchase
You will need to purchase the
following items separately to
mount your baby unit:
Use a pencil to mark two holes in
parallel. Make sure they are the same
distance apart as the wall mount holes
on the baby unit.
NOTESNOTE
Note
• Check for reception strength and camera
angle before drilling the holes.
2 screws
2 wall plugs
Drill two holes in the wall.
If you drill the holes into a stud, go to
step 3.
-OR-
If you drill the holes into an object other
than a stud, insert the wall plugs into
the holes. Tap gently on the ends with a
hammer until the wall plugs are flush with
the wall.
Insert the screws into the holes and
tighten the screws until only 6mm of the
screws are exposed.
Depending on your preference, choose
the upright or lateral orientation to mount
your unit. Align the wall mount holes at the
bottom or at the rear side of the baby unit
with the screws on the wall. Slide the baby
unit down until it locks into place.
OR
Tilt or rotate to adjust camera angle.
OR
NOTESNOTE
Note
• The types of screws and wall plugs you
need depend on the composition of the
wall.
Customer service and product warranty
Parent unit icons
Declaration of Conformity
The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging,
indicates they must not be disposed of in domestic waste as they contain substances that can be
damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more
than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive
(2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
Disposal of batteries and product
This product is intended for use within UK.
This equipment complies with the essential requirements to EU’s Radio Equipment
Directive (2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and
telecommunication equipment.
VTech Telecommunications Ltd. hereby declares that
this Video Monitor LM808-2W complies with the essential requirements and other relevant
provisions of EU’s Radio Equipment Directive (2014/53/EU) and UK’s Radio Equipment
Regulations 2017.
The Declaration of Conformity for the LM808-2W is available from
www.vtechbabycare.com.
Manufacturer: VTech Telecommunications Ltd.
23/F., Tai Ping Industrial Centre, Block 1, 57 Ting kok Road, Tai Po, Hong Kong.
Importer: VTech Electronics Europe Plc.
Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.
This warranty is valid for the UK and Ireland only. For products purchased outside
the UK and Ireland, please contact your local distributor or place of purchase.
P
R
O
D
U
C
T
W
A
R
R
A
N
T
Y
ONE
YEAR
PRODUCT WARRANTY
Thank you for choosing this quality product from VTech.
1.The product detailed above is covered by a one year warranty from the date of purchase,
against any defects in materials or workmanship.
2.The product may be returned to the place of purchase. Alternatively the product can be
returned to VTech Electronics Europe Plc (see address below), with proof of purchase,
without proof of purchase no replacement will be provided.
3.VTech Electronics Europe Plc will examine the product and if it is found to be defective
due to faulty materials or workmanship, will replace the product at their discretion.
4.If the product covered by this warranty is damaged due to misuse, modification or
unauthorized repair, or because of faulty batteries, battery discharge or incorrect
electrical connections, then this warranty becomes void.
5.This warranty is personal to the original purchaser and is not transferable.
6.Breakages to the LCD screen are not covered by the warranty.
7.Products returned to VTech Electronics Europe Plc, should be sent to the address shown
below and packed carefully to avoid damage in transit. Please do not include batteries or
adaptors. Please include details of the fault together with your name and address,
contact phone number and/or email address.
8.To keep an online record of your warranty, please register your product online at
www.vtech.co.uk/clubvtech
VTech Electronics Europe Plc, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane,
West Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT
CONSUMERS’ STATUTORY RIGHTS.
UK
PRODUCT REGISTRATION
Visit www.vtech.co.uk/clubvtech/login
to register your VTech product
By joining the VTech Club you can also enter competitions,
find out about news and events, seek expert advice for parents
and let your kids play fun learning games and activities.
IMPORTANT
Please retain this booklet with
your sales receipt as proof of
the date of purchase.
Customer Service
Please call our Consumer
Services Department on
03306 780149 (from UK) or
+44 3306 780149 (outside UK)
and a service representative
will be happy to help you.
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Maximum power used by the transmitter: 0.1W (100mW)
Channels 32
LCD 5” Colour LCD
(WQVGA 480x272 pixel)
Nominal effective range Actual operating range may vary according to environmental
conditions at the time of use
Power requirements Parent unit: 3.6V Ni-MH battery
Baby unit power adaptor: Output: 5V DC @ 1A
Parent unit power adaptor: Output: 5V DC @ 1A
Technical specifications
Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license.
The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.
For LM808-2W only
If you are viewing baby unit , the
POWER LED light of baby unit
turns on. As baby unit is not being
viewed, its POWER LED light flashes.
Status check - Two baby units
Select Patrol as your monitoring mode
to alternately view the image from baby
units and every 10 seconds.
Change different views
- Patrol
10s
Select Split as your monitoring
mode to view the images from both
baby units at once.
Change different views
- Split
In Single CAM or Patrol
mode, press VIEW to
switch between the
image of baby units
and .
Press VIEW
Change different views - Single CAM
26
26
26
Note
• If you power on only one baby unit, you may see the parent unit displaying and then , and
the LINK LED light flashing.
• Press VIEW in Single CAM or Patrol mode to switch to the baby unit you have powered on.
26
Press
Status icons
Connection status
• - Strong signal strength.
• - Moderate signal strength.
• - Low signal strength.
• - Weak signal strength.
Split mode (*For LM808-2W only)
Patrol mode (*For LM808-2W
only)
or
Current view status
• The baby unit number that is
being viewed when in:
-Single CAM mode.
-Patrol mode (*For LM808-2W only)
-Split mode (*For LM808-2W only)
Night vision - On
Zoom - On
Lullaby - On
oF or
oCReal-time temperature
• Real-time temperature detected
by the baby unit in Fahrenheit
(oF) or Celsius (oC) (e.g. 57
oF or
14
oC).
Temperature alert tone - On
Mute alert
• Displays when the parent unit
speaker volume is set to off.
• Displays when the parent unit is
talking to the baby unit.
9-level sound indicator
• indicates low sound level
detected by the baby unit.
• indicates moderate
sound level detected by the baby
unit.
• indicates high sound
level detected by the baby unit.
Main
menu Sub-
menu
Alert tones
• Set the parent unit to beep when the
battery is low.
• Set the parent unit to beep when the
link between the parent unit and the
baby unit is lost.
• Set the confirmation tone on or off
when selecting an option in the
menus.
• Set the parent unit to beep when the
baby unit detects sounds while in Split
mode. (*For LM808-2W only)
Temperature
/
• Set the parent unit to beep
whenever the room temperature
detected by the baby unit falls
outside of the set temperature range.
• Set the minimum temperature.
• Set the maximum temperature.
• Set temperature display in
Fahrenheit (oF) or Celsius (oC).
Main
menu Sub-
menu
Sound activation - screen and audio
/
Turn on/off sound activation
• When it is on, and the baby unit detects no
sound, the parent unit screen remains off
to save power. Once a sound is detected,
the parent unit screen and speaker turn on
automatically, and you can see and hear your
baby. The parent unit will then turn off again
after 50 seconds of no sound detection.
NOTESNOTE
Note
• When the parent unit screen is off and it receives
alerts, for example, link lost between parent unit
and baby unit, or battery is low, the parent unit
screen and speaker will turn on for 10 seconds.
VOX (Voice Activated Alert) Sensitivity
• You can set VOX sensitivity levels
to activate parent unit screen and
sound when baby unit detects
sounds that exceed certain levels.
See Sound sensitivity and sound
activation section.
Main
menu Sub-
menu
Brightness
• Adjust the parent unit’s LCD
brightness.
Camera settings
Baby unit speaker volume
• Adjust the baby unit’s speaker
volume.
Monitoring mode (*For LM808-2W only)
• Single mode
• Split mode
• Patrol mode
Lullaby
/ Play/Stop lullaby
• Select one of the soothing sounds,
or white noise.
• Select one of the five melodies.
• Play all melodies.
• Set timer to stop playing the
selected melody or soothing sound.
Warning icons and messages
• No link between units
• Battery low at Parent Unit
• Sound detected when in Split
view (*For LM808-2W only)
• Temperature too high at Baby Unit
• Temperature too low at Baby unit
Status icons
Battery status
• animates
when the battery is charging.
• - battery is fully charged.
• - battery is low and needs
charging.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VTech LM808-2W bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VTech LM808-2W in de taal/talen: Engels als bijlage per email.

De handleiding is 12.2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info