809800

VTech LM808-1W Handleiding

1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Note
• This baby monitor should be for use by adults only.
• It is not a substitute for proper adult supervision, and should not be used as such.
Test your baby monitor
You may test the baby monitor before initial use, and at regular times thereafter.
Caution
• For hearing protection, make sure the parent unit is more
than 1 metre away from the baby unit. If you hear any
feedback, move the parent unit further until the noise
stops. You can also press on the parent unit to reduce
the noise.
1. Make sure your baby unit and parent unit are on.
2. The parent unit displays images from the baby unit.
• Speak towards the microphone of the baby unit.
You will hear the sound at the parent unit.
Note
• When the parent unit displays and then No Link to CAM # (# represents the baby unit
number), and the LINK LED light flashes, move the parent unit closer to the baby unit (observe the
minimum distance of 1 metre). You can also check if the baby unit is connected to a live power socket
and switched on.
Tip
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the
baby unit.
Positioning the baby monitor
Caution
• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the
baby’s cot or playpen.
Note
• To avoid interference from other electronic devices, place your
baby monitor at least 1 metre away from devices such as wireless
routers, microwaves, cell phones and computers.
1. Place the baby unit more than 1 metre away from your baby.
2. Adjust the angle of the baby unit camera to aim at your baby.
3. Bend down the temperature sensor so that it stays away from baby unit to avoid deviation
of temperature detection.
4. Place the parent unit more than 1 metre away from the baby unit to avoid feedback.
Power on or off the baby unit
• Slide the ON/OFF switch to ON to turn on the baby unit. The ON/OFF LED light turns on.
• Slide the ON/OFF switch to OFF to turn off the baby unit. The ON/OFF LED light turns off.
Power on or off the parent unit
• Press and hold POWER to turn on the parent unit. The screen turns on.
• Press and hold POWER again to turn off the parent unit. The screen turns off.
Turn on or off the parent unit screen
You can turn on or off the parent unit screen without powering off the parent unit. You can
still hear sound from the baby unit.
• Press and hold LCD ON/OFF on the parent unit to turn off the screen.
• Press any keys on the parent unit to turn on the screen again.
Adjust speaker volume
For parent unit:
• Press or on the parent unit at any time when viewing images. As you adjust the
volume, the number of solid bar shows on indicates the current volume level.
For baby unit:
The baby unit speaker volume determines the lullaby volume and talkback volume
transmitted from parent unit. It can be adjusted in the parent unit.
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose the desired volume level, Level 1 is the softest while Level 5 is the
loudest. Then, press to confirm your selection.
User’s manual
LM808-1W
Full Colour Video Monitor
1. Press when the parent unit is idle.
2. Press or to choose VOX Sensitivity.
3. Press or to choose the desired sensitivity level.
Tips
• You can adjust the baby unit placement to improve the sound detection.
• If you want to use a sound machine or white noise machine for natural white noise while using this
baby monitor to check on your baby, you can:
- Lower the volume of your sound machine or white noise machine; or
- Lower the sensitivity level of your baby monitor to medium (level 3) or below. Default level is the
highest level.
Turn on or off the sound activation
When Sound activation is on, the parent unit screen remains off to save power when the
baby unit detects no sound.
Once the baby unit detects sounds that are louder than the chosen sound sensitivity level,
the parent unit screen and speaker turn on automatically. The parent unit will then turn off
again after 50 seconds of no sound detection.
1. Press when the parent unit is idle.
2. Press or to choose Sound-activated Screen.
3. Press or to choose On or Off, then press to confirm your selection.
Notes
• If you have muted the parent unit speaker, only the parent unit screen will turn on when a sound is
detected.
• When the parent unit screen is off and it receives alerts, for example, link lost between parent unit
and baby unit, or battery is low, the parent unit screen and speaker will turn on for 10 seconds.
Zoom
You can zoom in while viewing images from the baby unit.
• Press to zoom in.
• Press or to move the zoomed image downward or upward.
• Press or to move the zoomed image leftward or rightward.
• Press again to zoom out.
Talk
You can use the TALK function of the parent unit to comfort your baby.
1. Press and hold TALK on the parent unit. The TALK light turns on.
2. Speak towards the microphone on the parent unit. Your voice is broadcast to the baby unit.
3. Release the TALK key to stop the broadcast.
Notes
• The parent unit speaker is muted during voice broadcast. Sound transmission from the baby unit
resumes after TALK is released.
• The baby unit’s talkback volume can be adjusted via the parent unit menu.
Set alert tone
Low battery tone
You can set the parent unit to beep when the parent unit operates in low battery condition.
1. Press when the parent unit is idle.
2. Press or to choose Alert settings.
3. Press or again to choose Low Battery Tone, then press .
4. Press or to choose On or Off, then press to confirm your selection.
No link alert
You can set the parent unit to beep when the link between the parent unit and the baby unit is
lost.
1. Press when the parent unit is idle.
2. Press or to choose Alert settings.
3. Press or to choose No Link Alert, then press .
4. Press or to choose On or Off, then press to confirm your selection.
Monitor the temperature
Your baby unit monitors the temperature of your baby’s room with its built-in temperature
sensor. If the detected temperature is out of the preset temperature range, the parent unit
will display an alert message.
Set temperature range
You can set the desired room temperature alert range. The minimum temperature can be set
between 11 oC and 20 oC. The maximum temperature can be set between 21 oC and 30 oC.
1. Press when the parent unit is idle.
2. Press or to choose Temperature.
3. Press or to choose Minimum or Maximum, then press .
4. Press or to choose the desired minimum or maximum temperature, then press to
confirm your selection.
Temperature alert tone
You can turn on the temperature alert tone so that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. Press when the parent unit is idle.
2. Press or to choose Temperature.
1
Connect and charge the battery
What’s in the box
2
Before use
3
Using the baby monitor
3 Using the baby monitor (Cont’d)
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Maximum power used by the transmitter: 0.1W (100mW)
Channels 32
LCD 5” Colour LCD
(WQVGA 480x272 pixel)
Nominal effective range Actual operating range may vary according to environmental
conditions at the time of use
Power requirements Parent unit: 3.6V Ni-MH battery
Baby unit power adaptor: Output: 5V DC @ 1A
Parent unit power adaptor: Output: 5V DC @ 1A
Technical specifications
Specifications are subject to change without notice.
© 2021 VTech Communications, Inc.
All rights reserved. 07/21. LM808-1W_UK_CIB_V5-
EXIT
Caution
• The default volume of your parent unit is level 4, and the maximum volume is level 7. If you experience
high-pitched screeching noise from your baby monitor while positioning:
- Make sure your baby unit and parent unit are more than 1 metre apart, OR
- Lower the volume of your parent unit.
Operating range
The operating range of the baby monitor is up to 300 metres outdoors. The actual operating
range may vary depending on the environmental conditions and other interferences such as
walls, doors and other obstructions.
Lullaby
The baby monitor has five lullabies and four soothing sounds for you to comfort your baby.
You can play lullabies or soothing sounds on the baby unit by controlling remotely with the
parent unit.
To play lullabies:
1. Press when the parent unit is idle.
2. Press or to choose Play Lullaby.
3. Press or to choose Play Melodies, then press .
4. Press or to choose a lullaby, or choose Play All, then press .
• If Play All is selected, the five lullabies will be played one after the other, until all of
them are played.
5. When the desired lullaby is selected, press or to choose Play, then press .
To play soothing sounds:
1. Press when the parent unit is idle.
2. Press or to choose Play Lullaby.
3. Press or to choose Play Soothing Sounds, then press .
4. Press or to choose a soothing sound, then press .
To stop lullabies or soothing sounds:
1. Press when the parent unit is idle.
2. Press or to choose Play Lullaby.
3. Press or to choose Stop, then press .
To set auto timer for lullabies:
While the baby unit is playing a lullaby or soothing sound, the auto timer feature automatically
stops the lullaby or soothing sound after playing for 15/30/45/60 minutes. You can set auto
timer for lullabies with the parent unit.
1. Press when the parent unit is idle.
2. Press or to choose Play Lullaby.
3. Press or to choose Auto Timer, then press .
4. Press or to choose the desired lullabies duration, then press to confirm your selection.
After 15/30/45/60 minutes, the lullaby or soothing sound will stop automatically.
Adjust LCD brightness
You can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
1. Press when the parent unit is idle.
2. Press or to choose Brightness.
3. Press or to choose the desired level of brightness.
Turn on and off the dim mode
The dim mode helps save parent unit power. Your parent unit display will dim automatically
after 10 minutes of inactivity, when no keys are pressed or alerts are received from the baby
unit.
NOTESNOTE
Note
• While the screen is dimmed, any keypress or alert message will trigger the screen to return to the
preset brightness level. After 10 minutes of inactivity, it will dim again.
Adjust the sound sensitivity of the baby unit
You can turn on Sound activation and adjust the VOX sensitivity to detect sounds and turn
on the parent unit while its screen is switched off or dimmed.
When the baby unit detects sounds that exceed certain levels, the parent unit screen will
turn on and the baby unit starts transmitting the sounds to the parent unit, and you can see
and hear your baby. If you have turned on the Night light Auto-on and the Projection light
Auto-on feature, they will turn on automatically to sooth your baby.
If you turn off Sound activation, you will hear sounds from the baby unit all the time, even
when the parent unit screen is switched off.
63
> 1 metre
63
63
> 3ft (1m)
63

1metre
1
2
4
3
Connect the baby monitor
NOTESNOTE
• The rechargeable battery in the parent unit is built-in.
• Use only the power adaptors supplied with this product.
• Make sure the baby monitor is not connected to a switch-controlled electric outlet.
• Connect the power adaptors in a vertical or floor mount position only. The adaptors’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,
or cabinet outlets. Otherwise, the adaptors may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adaptor cords are out of reach of children.
Charge the parent unit battery
When you have connected the parent unit and installed its battery for the first time or after
power outage, the parent unit powers on automatically. The battery icon indicates the
battery status (see the following table).
NOTESNOTE
Notes
• Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When
the parent unit battery is fully charged, the battery icon becomes solid .
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,
turn the parent unit off while charging.
• The standby time varies depending on the sensitivity level you set, your actual use and the age of the
battery.
Battery indicators Battery status Action
The battery icon is off and
displays .
Parent unit operates
using AC power, and is
charging the battery.
The screen displays the
low battery alert
and the battery icon
becomes .
The battery has very little
charge and may be used
for only a short time.
Charge without interruption (about 30
minutes).
The battery icon becomes
.
The battery is fully
charged.
To keep the battery charged, connect
it to AC power when not in use.
Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative
Commons license.
The Stream Noise sound file was created by Caroline Ford, and is used under the Creative
Commons license.
The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative
Commons license.
The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons
license.
> 1metre
< 1metre


> 3ft (1m)
﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏
﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏
< 3ft (1m)
63
≥
< 3ft (1m)
3ft (1m)
63ē
63ē
> 1metre
< 1metre

1
2
1
2
1
2
The applied nameplate is located at the bottom of the baby
unit’s base.
When using your equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock
and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above
2 metres.
4. This product is not a substitute for adult supervision of the
infant. Supervising the infant is the responsibility of the
parent or carer. This product could cease operating, and
therefore you should not assume it will continue working
properly for any given period of time. Further, this is not
a medical device and should not be used as such. This
product is intended to assist you in supervising your baby.
5. Do not use this product near water, for example, near to
a bath, sink, swimming pool or shower.
6. CAUTION: Use only the battery provided. There may be
a risk of explosion if a wrong type of battery is used for
the parent unit. The battery cannot be subjected to high
or low extreme temperature and low air pressure at high
altitude during use, storage or transportation. Disposal of
battery into fire or a hot oven, or mechanically crushing or
cutting or the battery can result in an explosion. Leaving
the battery in an extremely high temperature surrounding
environment can result in an explosion or the leakage of
flammable liquid of gas. Battery subjected to extremely
low air pressure may result in an explosion or the leakage
of flammable liquid or gas. Dispose of used battery
according to the instructions.
7. Use only the adaptors included with this product.
Incorrect adaptor polarity or voltage can seriously
damage the product.
Baby unit power adaptor: Output: 5V DC 1A;
Parent unit power adaptor: Output: 5V DC 1A.
Use only adaptors and battery listed below.
Power adaptor information:
VTech Telecommunications Limited.
Model : VT05EUK05100(UK), VT05EEU05100(EU)
Rechargeable battery information:
Corun - Ni-MH AAA900mAh 3.6V
Ni-MH AAA900mAh 3.6V
9. The power adaptors are intended to be correctly oriented
in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
10. For pluggable equipment, the socket-outlet should
be installed near the equipment and should be easily
accessible.
11. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
12. Do not cut off the power adaptors to replace them with
other plugs, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
14. This product should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supply in your home,
consult your dealer or local power company.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf,
stand or other unstable surfaces.
17. This product should not be placed in any area where
proper ventilation is not provided. Slots and openings
in the back or bottom of this product are provided for
ventilation. To protect them from overheating, these
openings must not be blocked by placing the product
on a soft surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or heat
source.
18. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of any
kind on the product.
19. To reduce the risk of electric shock, do not disassemble
this product, but take it to an authorized service facility.
Opening or removing parts of the product other than
specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can
cause electric shock when the product is subsequently
used.
20. You should test the sound reception every time you turn
on the units or move one of the components.
21. Periodically examine all components for damage.
22. There is a very low risk of privacy loss when using
certainelectronic devices, such as baby monitors,
cordless telephones,etc. To protect your privacy, make
sure the product has never beenused before purchase,
reset the baby monitor periodically bypowering off
and then powering on the units, and power off thebaby
monitor if you will not use it for some time.
23. Children should be supervised to ensure that they do not
play with the product.
24. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 0oC
and 40oC.
2. Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to
excessive heat such as bright sunshine or
fire.
4. Warning—Strangulation Hazard—
Children have STRANGLED in cords. Keep this cord out
of the reach of children (more than 0.9 m away). Do not
remove this tag.
5. Never place the baby unit(s) inside the baby’s cot or
playpen. Never cover the baby unit(s) or parent unit with
anything such as a towel or a blanket.
6. Other electronic products may cause interference with
your baby monitor. Try installing your baby monitor
as far away from these electronic devices as possible:
wireless routers, radios, cellular telephones, intercoms,
room monitors, televisions, personal computers,
kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the
pacemaker.
• Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and
according to the instructions in this user’s manual, the product
is safe to be used based on scientific evidence available
today.
Important safety instructions
VOX
Sensitivity
level Level 5
(Highest)
Level 4
(High)
Level 3
(Medium)
Level 2
(Low)
Level 1
(Lowest)
Description (Default setting)
The parent unit
screen and speaker
turn on for very small
sounds, including
background noises
from your baby’s room.
The parent unit screen
and speaker turn on
for soft babbling
and louder sounds
from your baby. The
parent unit remains
quiet when your baby
sleeps soundly.
The parent unit screen
and speaker turns on
for loud babbling and
louder sounds from
your baby. The parent
unit remains quiet
when your baby makes
soft sounds.
The parent unit screen
and speaker turn on
for crying and louder
sounds from your
baby. The parent unit
remains quiet when
your baby makes soft
sounds.
The parent unit screen
and speaker turn on
for loud crying or
screeching sounds
from your baby. The
parent unit remains
quiet when your baby
makes soft sounds.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VTech LM808-1W bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VTech LM808-1W in de taal/talen: Engels als bijlage per email.

De handleiding is 10.52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info