636393
8
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
UNO
X
R
using the + or - keys (the program number
will show on the display)
- start the cooking program pressing the key
START/STOP
While the oven works with a program the
visualization of the cooking parameters is like the
one you have in the manual mode.
While the oven works with a program IT IS NOT
POSSIBLE to modify the cooking parameters.
It is possible to interrupt the cooking cycle by
pressing the START / STOP key.
At the end of a cooking cycle the heating elements
and motors will be switched off, the buzzer will ring
for 15 seconds, the digits 0.00 will flash for 45
seconds on the display, the set temperature remains
the one entered at the beginning of the cooking
cycle and the START/STOP LED will remain turned
on.
If during the 45 seconds of flashing digits (0.00) the
operator set a time (using the + or – keys), the oven
automatically starts functioning.
At the end of the 45 seconds or if the cooking cycle
is interrupted by pressing the START / STOP keys,
all the parameters previously set will turn into 0 (the
operator will be in the same situation there is when
the oven has just been turned on) and the START/
STOP LED will be switched off.
Automatic pre-heating
An automatic pre-heating phase is run only when
you use the oven with programs.
When you start the program with the START / STOP
key, the oven starts to heat up the cavity and you do
not see any digit on the displays. When the oven
reaches the pre-heating temperature, it gives a long
sound. At this point, it is necessary to open the door,
place the trays with the food to be cooked inside the
oven and close the door: the chosen program will
start automatically.
Pre-heating temperature is equal to the set
temperature plus 30°C.
3.2 DESCRIPTION AND USE OF THE Dynamic
CONTROL PANEL
The control panel can work both in the manual and
in the programmed mode.
For each cooking cycle (both in the manual and
in the programmed mode) the operator can set 3
cooking steps. For each step it is possible to enter
desired time, cavity temperature, percentage of
humidity.
MANUAL MODE
Switching On / Switching Off
As soon as current reaches the appliance, the
control panel switches automatically on; on the
display you will read the digits 0.00 (they express
the time in hours.minutes), the LED of the “TIME”
switches on as well as the lights inside the cavity.
15 minutes after the end of the cooking cycle (both
in the manual and in the programmed mode) both
in the cases that a program finishes or the operator
pushes the START/STOP key, if no keys are pressed,
the control panel switches automatically off. The
lights, all the display and all the LEDS will be
switched off, except for the START / STOP LED. To
switch on the control panel it is sufficient to press the
START/STOP key.
SELECT key.
The SELECT key allows the operator to select three
parameters: TIME, TEMPERATURE and HUMIDITY.
TIME set up
To set the time of functioning, it is sufficient to
operate on the + and – keys (time can be set from 0
hours and 01 minute to 9 hours and 59 minutes)
When you read INF on the TIME display, the oven
will work continuously until you stop it pressing the
START/STOP key.
TEMPERATURE set up
To set the temperature desired inside the cavity
it is sufficient to operate on the + and – keys
(temperature can be set from 0 to 260°C – starting
temperature 30°C)
ENGLISH
ENGLISH
8
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Unox XF185 Dynamic bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Unox XF185 Dynamic in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info