779233
7
Verklein
Vergroot
Pagina terug
1/33
Pagina verder
1312
16.11.2020
3.3.5. SETTING THE STARTUP TIME
You can set the time for automatic activation and
operation of the device. To do this, when the device
is in the standby mode, press the timer button on the
control panel (6) or on the remote control (2). After
setting the time in the range of 0-12 hours, the device
will display the set time until automatic start-up and the
timer indicator (8) will light up – this time will be counted
down and after it has expired, the device will start
automatically. The default heating temperature is 23 oC.
CAUTION: if the heating temperature has not been
set and no operating mode has been programmed,
the device will automatically turn off after 12 hours of
continuous operation.
3.3.6. PROGRAMMING THE OPERATING MODE
CAUTION: this operation can only be programmed
using the remote control!
A. Setting the time and day of the week.
In the standby or operating mode, set the time and
day of the week. Press the "SET" button (3) and
the display will show "12" as the default hour. Use
the parameters increasing or decreasing buttons
(5) to set the current hour, then by pressing the
"SET" button (3) to accept the set hour to go to the
minutes setting. The minutes are also set with the
same buttons (5) and conrmed with the "SET"
button (3). After setting the time, the weekday
"d1" will appear, which is Monday by default. Use
the parameters decreasing or increasing buttons
(5) to set the current day of the week ("d1" – "d7"
respectively Monday–Sunday), and then press
the "OK" button to conrm the settings. The time
setting range is 00–23 hours and 00–59 minutes.
CAUTION: the device must be reset after power is
removed. Then use the „SET“ button (5) to check if the
time and day of the week are correct.
B. Blowing temperature setting
During operation, press the parameter
decreasing/increasing button (5), the display will
show „23“ as the default heating temperature.
If necessary, use the same buttons (5) to set the
desired temperature (in the range of 10–49 oC),
and conrm it with the „OK“ button (5).
C. Setting the weekly operation mode.
After previous setting of the time and day of the
week, you can program the weekly operation
mode of the device.
a) Press the ON/OFF button on the device‘s panel (4)
or remote control (1) to start the device.
b) Press the program selection button (8) to enter the
weekly program settings – the program indicator
will light on the display.
c) Press the button for setting the day of the week
(7) on the remote control, and after displaying
the default day „d1“ (Monday) set the current
day by pressing the same button (according to
the diagram: („d1“ „d7“ respectively Monday–
Sunday) as necessary.
Message D1 D2 D3
Day of
the week Monday Tuesday Wednesday
Message D4 D5 D6 D7
Day of
the week Thursay Friday Saturday Sunday
d) Press the time of day edit button (10) on the
remote control, the display will show „P1“. By
pressing the same button again, we can choose
one of the six times (P1–P6) for a given day with
the setting of any time and temperature.
e) Press the ON time setting button on the remote
control (9), the display will show „00“. The next
pressing of the same button increases the time of
starting the device by one hour, etc. according to
this scheme - the time range from 00 to 24 can
be selected. For example, in the picture below,
turning on at 7:00:
On the back of the remote control, remove the
protective coating of the battery (1) – to do this, pull it
out of the battery compartment (2) by pulling it towards
you (3).
CAUTION: if the protective coating is not removed
despite the ecient battery, the remote control will not
work!
INSTALLATION/REPLACEMENT OF THE REMOTE
CONTROL BATTERY
Symptoms of a depleted remote control battery include
weak or no response to the buttons on the remote. To
remove the battery compartment, press and hold the
compartment lock (5), and with the help of a ngernail
or a sharp object, lift the battery compartment and pull
it towards you away from the remote control (4).
CAUTION: When installing batteries in the remote
control, pay attention to the correct polarity.
3.3. DEVICE USE
3.3.1. STANDBY MODE
After installing the device on a vertical wall, connect the
plug to the power source and then set the switch on
the side of the device (1) to the ON „I“ position. The
message „S“ will appear on the display, which means
that the device is in the standby mode, i.e. ready for
operation.
3.3.2. TURNING ON/OFF THE DEVICE
Press the ON/OFF button on the device control panel
(4) or remote control (1) to turn on the device. It will
automatically switch to a blowing mode, and the display
will show the message „- -“
3.3.3. SETTING THE HEATING POWER
Press the heating power selection button on the control
panel (5) or on the remote control (4) to select one of
the two heating settings. Default setting „I“ 1000 W.
Pressing the same button again changes the power
to „II“ 2000 W. The appropriate selection is signaled
adequately by one or two lights on the device control
panel (2).
3.3.4. SETTING THE TIMER
The timer function counts down the device operating
time until it is automatically turned o, i.e. it enters the
standby mode. Available hours range: 0-12. Press the
timer button on the control panel (6) or on the remote
control (2), the display will show the current time. Each
press of the timer button increases the operating time
of the device by one hour. After selecting the desired
operating time, it will be shown on the display for
about 5 seconds, followed by the timer indicator on
the display, and the display itself will show the previous
parameter.
1
24
3
5
5
38,5cm
180cm min
Below is an example of setting 9:30 for Wednesday:
f) Press the switching-o time setting button (11)
on the remote control, the device will show the
default switching-on time on the display. The
switching-o time is set in a similar way as in the
case of setting the switching-on time (selectable
time range from 00 to 24), with the dierence
that the specic time is selected using the o time
button (11) on the remote control.
CAUTION: the time of automatic switching o
of the device cannot be earlier than the time of
switching on! If the hours are the same, the device
goes into the standby mode – yes.
g) Use the parameter increasing/decreasing buttons
(5) to set the desired temperature (within the
range of 10–49 oC).
h) By repeating steps c)–g) you can set the operating
parameters for each day of the week.
i) Press the „OK“ parameter conrming button (5)
on the remote control to nish programming.
CAUTION: when working in the programmed
mode, by pressing the button for setting the
day of the week on the remote control (7), you
can enter the settings for a given day and then
using the program editing button (10) to check the
automatic start time, and by pressing the same
button again, the automatic stop time.
j) To cancel the weekly program mode, press the „P“
button (8) on the remote control.
3.3.7. ACTIVATION/DEACTIVATION OF THE OPEN
WINDOW DETECTION
After turning on the device, press the button for the
open window detection function (6) on the remote
control using the ON/OFF button (on the control panel
4 or on the remote control 1). Indicators (7) and (9) will
light up on the display of the device. The display will
show the default temperature „23“. This temperature
can be changed with the parameter decreasing/
increasing buttons (5). If the device detects a drop
in room temperature, it will stop working. To switch
the device back on, press the ON/OFF button (on the
device panel 4 or on the remote control 1). Pressing the
button for the open window detection function (6) again
deactivates it – the function indicator on the display (7)
turns off.
ENEN
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Uniprodo UNI HEATER 03 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Uniprodo UNI HEATER 03 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens als bijlage per email.

De handleiding is 1.07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info