166761
1
Verklein
Vergroot
Pagina terug
1/17
Pagina verder
MOBILE POWER AMPLIFIERS
2 X 165 WATT
2 CHANNEL AMPLIFIER
4 X 140 WATT
4 CHANNEL AMPLIFIER
2 X 250 WATT
2 CHANNEL AMPLIFIER
4 X 250 WATT
4 CHANNEL AMPLIFIER
2 X 425 WATT
2 CHANNEL AMPLIFIER
4 X 150 WATT
1 X 300 WATT
5 CHANNEL AMPLIFIER
2 X 600 WATT
2 CHANNEL AMPLIFIER
1 X 540 WATT
1 CHANNEL AMPLIFIER
Ultimate Sound,Inc.
163 University Parkway
Pomona, CA 91768 USA
Tel: 909-594-2604
Fax: 909-594-0191
E mail : technicalsupport@ultimate-sound.com
WWW.ULTIMAT
E
-
SOUND.CO
M
Ultimate Europe AB
Flojelbergsgatan 7A S-431 37
Molndal, Sweden
Tel : 46-31 87 64 50
Fax : 46-31 87 20 04
E mail : europeansupport@ultimate-europe.com
INTRODUCTION
I. Description
This device is a high power, audio amplifier. Use it responsibly. Very
loud music can cause permanent hearing loss. This amplifier is intended
for installation in vehicles with a 12-Volt, negative ground electrical
system. Attempting to connect or operate the amplifier in another type of
electrical system may cause damage to the amplifier or the electrical
system.
II. About This Manual
Read the Instructions-
Be sure that you have read all operating instructions and understand all
safety precautions before installing and operating the amplifier. We
recommend that you have your T
3 series amplifier installed by a
specialist.
Follow the Instructions-
The instructions are intended to help you safely obtain the best
performance from the amplifier. Carefully follow all installation and
operating instructions.
Save the Operating Manual-
Keep the manual in a safe place after installing the amplifier. You may
have questions later.
Text Conventions used in this Manual-
Bold-
Headings and important information.
Bold, Underlined-
Very important information.
"Bold"-
As labeled on the amplifier, or quoted from elsewhere in this
manual.
III. Safety and Operating Precautions-
Caution!
This symbol warns the user of a potential risk or hazard if instructions are
not followed.
This arrow symbol points to a specific instruction for avoiding a
potential hazard.
ii
1
1. Installation
1.1 Installation- Mounting the Amplifier
Step 1- Disconnect the negative (-) battery cable before mounting the
amplifier or making any connections. Check the battery and alternator
ground (-) connections. Make sure they are properly connected and free of
corrosion
Step 2- Choose a mounting location for your amplifier. Find a location on a
flat surface away from heat and moisture. Be sure the mounting location and
the drilling of pilot holes for mounting will not present a hazard to any
wires, control cables, fuel lines, fuel tanks, hydraulic lines, or other vehicle
systems or components. Common mounting locations are under the front
passenger seat, or in the trunk area. Choose a location with unimpaired air
circulation. The amplifier will dissipate heat more efficiently if mounted
vertically.
Step 3- Use the supplied screws. Place the amplifier in the mounting
location, and mark the positions of the holes with a marker, pen or pencil.
Carefully drill the mounting holes in the marked positions.
Caution!
Check carefully before drilling any pilot holes.
Step 4- Use the supplied mounting screws to securely fasten the amplifier to
the mounting surface.
1.2 Installation- Power Connections
Step 1- Run a power cable from the battery to the amplifier mounting
location. Use rubber grommets to protect the cable anywhere it has to go
through metal.
T
3 4600,T3 4320,T3 2700,T3 2600,T3 2300,T3 5600,T3 1000 Use #8 AWG
or larger power and ground cable.
T
3 2160 - Use #10 AWG or larger power and ground cable.
Step 2- Connect one end of an in-line fuse holder to the power cable.
Connect the other end of the fuse holder to the positive battery post with 20
cm (or less) of the same cable. This fuse location will protect the system and
the vehicle against the possibility of a short circuit in the power cable. Be
sure to use a fuse and fuse holder adequate for the application. Do not place
a fuse in the holder at this time.
The maximum fuse rating for each amplifier in the T
3 series is:
T
3 4600 -2 X 30 A. T3 4320 - 30 A T3 2700 -2 X 30 A.
T
3 2600 -2 X 25 A. T3 2300 - 30 A. T3 2160 -15 A.
T
3 5600 -3 X 25 A. T3 1000 -2 X 20 A.
Caution!
Bridging fuses or replacing a fuse with one of a higher rating may
cause damage to the amplifier and the vehicle's electrical system.
POWER
Step 3- Run a remote turn on cable from the switched +12V source you
will be using to turn on the system components. This may be a toggle switch,
a relay, or your source unit’s remote trigger wire, or power antenna trigger
wire. Run this lead to the amplifier mounting location. Use #18 AWG wire
or larger.
+12V RMT GND
Step 4- Locate a secure grounding connection as
close to the amplifier as possible. Make sure the
location is clean and provides a direct electrical
connection to the frame of the vehicle. Connect
one end of a short piece of the same size cable as
the power cable to the grounding point. Run the other end of the cable to the
amplifier mounting location.
Step 5- connect the ground cable to the screw terminal labeled
“POWER, GND”.
Step 6- Connect the power cable to the amplifier at the screw terminal
labeled “POWER, +12V”.
Step 7- Connect the remote turn on cable to the screw terminal labeled
“POWER, RMT”.
1.3 Installation- Speaker Connections
Step 1- Run #16 AWG or larger connecting wire from your speakers to the
amplifier mounting location. Keep speaker wires away from power cables
and amplifier input cables. Use grommets anywhere the wires have to pass
through holes in the metal frame or sheet metal. Connect to the speakers
according to the type of terminals on each speaker.
Step 2- Strip 3/8" of insulation from the end of each wire and twist the wire
strands together tightly. Make sure there are no stray strands that might
touch other wires or terminals and cause a short circuit.
Step 3- Crimp spade lugs over the wire ends or tin the ends with solder to
provide a secure termination.
Step 4- Connect the wire ends to your amplifier as follows:
2
SPEAKER TERMINALS
3
Follow the (A/B/C/D+) (A/B/C/D-), channel and polarity markings, making
sure they match the channel and polarity of the connections at the
speakers.
MULTIPLE SPEAKER CONNECTION
PARALLEL- Each additional speaker decreases the load impedance
for the amplifier. The amplifier delivers more current and works
harder.
Caution : impedances lower than 2 ohms may cause damage to your
amplifier and is not recommended.
SERIES- Each additional speaker increases the load impedance for the
amplifier. Impedances higher than 8 ohms are rarely used for car
audio.
(+)
(
-
)
+
-
(+)
(
-
)
4 Ohm 2 Ohm
PARALLEL CONNECTION USING 4 OHM SPEAKERS
A
M
P
L
I
F
I
E
R
O
U
T
P
U
T
(A+) (A-) (B+) (B-)
( + ) ( - )
BRIDGE
SPEAKER
SPEAKER
(C+) (C-) (D+) (D-)
( + ) ( -
)
BRIDGE
SERIES CONNEC
4 Ohm 8 Ohm
4
(A+) (A-) (B+) (B-)
( + ) ( - )
BRIDGE
SPEAKER
1.4 Installation- Self-Bridging, 2+1 Mode
BRIDGED MONO-
Connect a 4Ω ohm speaker to the
terminals marked “(+), BRIDGE, (-)”,
making sure they match the polarity of
the connections at the speakers.
Caution!
Speaker or multiple speaker loads
totaling less than 4 ohms are not
recommended for “Bridged” or
“2+1 Mode”, and may damage the
amplifier.
T
3 4600, T3 4320-
Set the “MODE” switch to “2CH, 3CH”, or “4CH” and connect the
speakers accordingly. For “3CH” operation, bridge the “C” and “D”
channels.
2+1 MODE- (TRI-MODE)
Simultaneous stereo and mono operation, “2+1 Mode”, requires a passive
crossover to send low frequencies to the mono speaker and higher
frequencies to the stereo speakers. The following table lists the component
values for a 6 dB/Octave crossover at common frequencies using 4 ohm
speakers for stereo and an 8Ω speaker for mono(subwoofer):
FREQUENCY INDUCTOR CAPACITOR
80 Hz 16 mH 470 uF
100 Hz 7.5 mH 330 uF
120 Hz 7.5mH 330 uF
150 Hz 7.5 mH 220 uF
2+1 MODE WIRING DIAGRAM-
Use 100 Volt, non-polar capacitors, and connect them in series with the
stereo speakers as shown in the diagram. Connect the inductor in series with
(+)
(
-
)
+
-
(+)
(
-
)
TION USING 4 OHM SPEAKERS
A
M
P
L
I
F
I
E
R
O
U
T
P
U
T
the mono speaker as shown in the diagram. Be sure the inductor is rated to
handle the power of your amplifier.
(+)
(
-
)
5
HIGH LEVEL
1.5 Installation- Input
Connections
Low Level, High Impedance, Gold Plated
RCA Input Jacks-
For connecting to a source providing preamp level
outputs. Use heavy duty RCA patch cords designed for
mobile applications . Run the patch cables carefully,
maintaining as much distance as possible from power,
speaker, and accessory wiring. Make sure the RCA
plugs fit tightly for a secure connection.
Speaker Level Input Connector-
Use the supplied wiring harness to connect the speaker outputs from the
source unit(AM/FM/CD/DVD or Cassette) to the “HIGH LEVEL” input.
Wiring Harness Color Code- 2 Channel
White Wire
A Channel Positive( + )
White/Black Wire
A Channel Negative( - )
Gray Wire
B Channel Positive( + )
Gray/Black Wire
B Channel Negative( - )
Black Wire Ground
No Other Connection
(+)
(
-
)
(+)
(
-
)
(A+)
(A-)
(B+)
(B-)
CAPACITORSINDUCTOR
INPUT
A
B
HIGH LEVEL
Wiring Harness Color Code- 4 Channel
White Wire Channel A Positive( + )
White/Black Wire Channel A Negative( - )
Gray Wire Channel B Positive( + )
Gray/Black Wire Channel B Negative( - )
Green Wire Channel C Positive( + )
Green/Black Wire Channel C Negative( - )
Violet Wire Channel D Positive( + )
Violet/Black Wire Channel D Negative( - )
Black Wire Ground
No Other Connection
1.6 Installation- Check all Connections
Recheck all connections before reconnecting the negative(-) battery cable.
Insert the correct value fuse in the fuse holder at the battery before
attempting to turn on the system.
2. Operation
2.1 Operation- Input Level adjustments
Adjust the input level for the marked channel(s) with a small
screwdriver through the opening marked “LEVEL”. Turn
CW(clockwise) to increase the level, CCW(counterclockwise)
to decrease. Amplifiers will run cooler and produce less system
noise at lower level settings.
LEVEL
MIN MAX
Consult an experienced installation specialist for assistance in balancing the
levels in multi-amplifier systems, or systems with signal processing
accessories.
2.2 Operation- Built-in Crossovers
CROSSOVER FILTER SELECTION
The T
3 series amplifiers have built-in low-pass and high-
pass crossover filters for bi-amplifying your system.
Select " LPF, FULL or HPF" by moving the position of
the slide switch for each pair of channels. "LPF" selects
the low pass filter. "HPF" selects the high pass filter.
Selecting "FULL" defeats the crossover functions
X
-OVER
LPF- FULL- HPF
FREQUENCY ADJUSTMENT
6
LPF
40-240
After selecting the crossover function, adjust the low pass or high pass
frequency control with a small screwdriver through the opening marked
“LP/FREQ.” or "HP/FREQ.". Turn CW to set to a higher frequency,
CCW to set to a lower frequency.
7
POWER
PROTECT
BASS-BOOS
ON OFF
T
Turning the “BASS BOOST” switch to “ON” increases the
level of frequencies around 45Hz by 12dB.
2.3 Operation- Protection Circuits and
L.E.D. Indicators
“POWER.” L.E.D. INDICATOR- Provides a visual indication
that the amplifier is turned on.
“PROTECT” L.E.D. INDICATOR-
Provides a visual indication
that a problem exists and the protection circuitry has protected the
amplifier by shutting it down. Turn the system off and correct
the problem before turning the system on.
THERMAL PROTECTION-
The amplifier will shut down if its
temperature exceeds a safe operating level. The amplifier will remain off
until it cools to a safe operating temperature. Exercise care, the exterior of
the amplifier may get uncomfortably hot to the touch before shutting down.
OVERLOAD AND SHORT CIRCUIT PROTECTION-
The amplifier
will shut down if a short circuit condition exists, or if electrical current
demands exceed safe levels.
FUSE PROTECTION-
A blown fuse indicates a problem that
should be corrected before the fuse is replaced. Always replace
with the same value fuse. Never substitute a larger value fuse.
FUSE
15 A
15A
2.4 Operation- Location of Terminals,
Controls and LED indicators
T
3 4600, T3 4320
1. Power L.E.D. 2. Line level output 3. Line input jacks
4. Input level adjust 5. High pass freq. 6. Low pass Freq. adjust
7. Speaker level input 8. Protection L.E.D 9. Crossover select
10. Bass boost 11. Mode Switch
8
1. Fuse 2. Power terminals 3. Speaker terminals
1 2 3 4 5 6 7 6 5 4 3 8
9 10 11 10 9
2 3 3 1
T3 2700 T3 2600 T3 2300, T3 2160
1. Power L.E.D. 2. Speaker level input 3. Line level input
4. input level adjust 5. Bass boost 6. Low pass freq. adjust
7. Crossover select 8. High pass freq. adjust 9. Line level output
10. Protection L.E.D.
1 2 3 4 5 6 7 8 9
10
1. Fuse 2.Power terminals 3 . Speaker terminals
9
1 2 3
10
T
3 5600
1. Power L.E.D 2. Line level input 3. Input level adjust
4. High pass freq. adjust 5. Low pass freq. adjust
6. Protection L.E.D. 7. Crossover select 8. Sub- sonic freq switch
1 2 2 3 4 3 4 3 5 2 6
7 7 7 8
1. Fuses 2. Power terminals 3. Speaker terminals
1 2 3
11
12
3 1000
1. Power L.E.D 2. Speaker level input 3. Line input jacks
. Fuses 2. Power terminals
eaker terminals ( Duplicated positive and Duplicated negative )
T
4. Input level adjust 5. Bass Boost 6. Low pass freq. adjust
7. Crossover select 8. Line level output 9. Protection L.E.D.
1 2 3 4 5 6 7 8 9
1
.
3. Sp
1 2 3
13
Features and Specifications:
T3 2700 T3 2600 T3 2300 T3 2160
2 CHANNELS
POWER
AMPLIFIER
2 CHANNELS
POWER
AMPLIFIER
2 CHANNELS
POWER
AMPLIFIER
2 CHANNELS
POWER
AMPLIFIER
2 ohm Stable
Yes
Bridgeable
Yes, 4 ohm
Tri-mode
No
Terminals
Gold plated RCA jacks, speaker and power terminals
Soft Start
Yes
Line level input
RCA line level inputs,
Crossover
Low pass, High pass, 12dB/Octave, 40Hz-240Hz
Protection
Thermal, Short- circuit, DC offset, Fuse
Power Supply
Pulse Width Modulated, MOSFET power supply + 12V / Negative Ground
Line input
Yes
Bass Boost
+12dB @45Hz
High level Input
Yes
Line output
Yes
RMS/Max
Power, 4Ω, THD
<0.03%
2X200/400
Watts
2X180/360
Watts
2X 85/170
Watts
2X50/100
Watts
RMS/Max
Power, 2Ω, THD
<0.2%
2X300/600
Watts
2X215/425
Watts
2X125/250
Watts
2X80/165
Watts
Bridged
RMS/Max
Power, 4Ω
600/1200
Watts
425/850
Watts
250/500
Watts
165/330
Watts
Signal to Noise
Ratio
-100 dBA -100 dBA -100 dBA -100 dBA
Frequency
Response
10Hz-30kHz 10Hz-30kHz 10Hz-30kHz 10Hz-30kHz
Separation
-60dB -60dB -60dB -60dB
Input Sensitivity
100mV-1.5V 100mV-1.5V 100mV-1.5V 100mV-1.5V
Fuse
2 X 30A 2 X 25A 30A 15A
Dimensions
/Inches
19.7x11.9
x2.18
11.8x11.9
x2.18
9.8x11.9
x2.18
7.1x11.9
x2.18
Dimensions
/mm
500x301.6
x55.3
300x301.6
x55.3
250x301.6
x55.3
180x301.6
x55.3
14
T
3 4600 T3 4320 T3 1000 T3 5600
4 CHANNELS
POWER
AMPLIFIER
4 CHANNELS
POWER
AMPLIFIER
1 CHANNEL
POWER
AMPLIFIER
5 CHANNELS
POWER
AMPLIFIER
2 ohm Stable
Yes
Bridgeable
Yes No Yes
Tri-mode
Yes No
Terminals
Gold plated RCA jacks, speaker and power terminals
Soft Start
Yes
Line level input
RCA line level inputs,
Crossover
LPP, HPF, 12dB/Oct.40Hz-240Hz Low pass High/Low pass
Protection
Thermal, Short- circuit, DC offset, Fuse
Power Supply
Pulse Width Modulated, MOSFET power supply + 12V / Negative Ground
Line input
Yes
Bass Boost
+12dB @45Hz No
High level Input
Yes No
Line output
Yes No
RMS/Max
Power, 4Ω, THD
<0.03%
4X85/170
Watts
4X50/100
Watts
1x180/360
Watts
4X50/100
1X100/200
Watts
RMS/Max
Power, 2Ω, THD
<0.2%
4X125/250
Watts
4X70/140
Watts
1X275/540
Watts
4X75/150
1X150/300
Watts
Bridged
RMS/Max
Power, 4Ω
2x250/500
Watts
2x140/280
Watts
Mono
Channels
2X150/300
1X150/300
Watts
Signal to Noise
Ratio
-100 dBA -100 dBA -100 dBA -100 dBA
Frequency
Response
10Hz-30kHz 10Hz-30kHz 10Hz-30kHz 10Hz-30kHz
Separation
-60dB -60dB -60dB -60dB
Input Sensitivity
100mV-1.5V 100mV-1.5V 100mV-1.5V 100mV-1.5V
Fuse
2 X 30A 30A 2 X 20A 3 X 25A
Dimensions
/Inches
13.8x11.9
x2.18
8.7x11.9
x 2.18
8.7x11.9
x2.18
15.7x11.9
x2.18
Dimensions
/mm
350x301.6
x55.3
220x301.6
x55.3
220x301.6
x55.3
400x301.6
x55.3
These specifications are subject to change in the continuing effort to
improve the product.
15
Troubleshooting:
Condition Possible Cause Possible Solution
No sound Low or no remote turn
on voltage, or no remote
turn on connection
Check the remote turn on
connection and the voltage at
the amplifier and source unit
Blown fuse(s) Check all system fuses
Wiring problems Recheck all connections
Check for short circuits
Blown speakers Check speakers on another
amplifier
Amplifier
shut down
Protection circuit
protecting against
overheating or overload
Check for adequate ventilation
Check load impedance(2 ohm
stereo, 4 ohm bridged)
Check speaker wiring for short
to the vehicle chassis
Reduce input level
Distortion Input level not properly
adjusted
Speaker damage
Readjust amplifier input level
Check speakers on another
amplifier
Poor bass
response
Speakers out of phase Recheck speaker wiring
Reverse polarity of one channel
Ticking
noise
Radiated noise from
spark plug wires
Reroute amplifier input wiring
Install a noise filter
Whining
noise
Alternator noise caused
by poor grounding of
amplifier, source, other
component, battery, or
alternator
Check all ground connections
Install a noise filter on the
source unit’s power cable
Install a coupling transformer
in the signal path to improve
ground isolation for the signal
path
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ultimate t3 2600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ultimate t3 2600 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info