765111
15
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
OWNER’S MANUAL
TR 4.0
Please carefully read this entire manual before operating your new treadmill
1
TABLE OF CONTENTS
Important Safety Instructions 2
Important Electrical Instructions 3
Grounding Instructions 3
Important Operation Instructions 4
Assembly Instructions 5
Transport Instructions 11
Features 12
Console Operation 14
Programmable Features 17
Using Heart Rate Transmitter 27
General Maintenance 29
Exploded View Diagram/Parts List 34
ATTENTION
This treadmill is intended for residential use only and is warranted for this application.
Any other application voids this warranty in its entirety.
XT810-AT38CEGS_1109A
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your treadmill from the electrical
outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install
the treadmill on a flat level surface with access to a 230-volt, 10-amp grounded outlet with
only the treadmill plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH
ONLY ONE OUTLET ON THE END.
The treadmill should be the only appliance in the circuit in which it is connected.
DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER
ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A serious shock or fire hazard
may result along with computer malfunctions. See Grounding Instructions, page 3.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet
and treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance
between the rear of the treadmill and any fixed object.
Keep children away from the treadmill. There are obvious pinch points and other caution
areas that can cause harm.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not
working properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, then remove the plug from the outlet.
Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Their purpose is to provide you
with an approximate measurement in relation to your target heart rate. Use of a chest
transmitter strap is a much more accurate method of heart rate analysis. Various factors,
including the user’s movement, may affect the accuracy of heart rate readings. The
pulse sensors are intended only as exercise aids in determining heart rate trends in
general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for
use on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
3
IMPORTANT ELECTRICAL INSTRUCTIONS
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any appliance with a
large motor, the GFCI will trip often. Route the power cord away from any moving part of the treadmill
including the elevation mechanism and transport wheels.
NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%)
or more, the performance of your treadmill may be affected. Such conditions are not covered under your
warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for
proper testing.
NEVER expose this treadmill to rain or moisture. This product is NOT designed for use outdoors, near a
pool or spa, or in any other high humidity environment. The operating temperature specification is 40 to
120 degrees Fahrenheit, and humidity is 95% non-condensing (no water drops forming on surfaces).
Circuit Breakers: Some circuit breakers used in homes are not rated for high inrush currents that can
occur when a treadmill is first turned on or even during use. If your treadmill is tripping the house circuit
breaker (even though it is the proper current rating) but the circuit breaker on the treadmill itself does not
trip, you will need to replace the home breaker with a high inrush type. This is not a warranty defect.
This is a condition we as a manufacture have no ability to control. This part is available through most
electrical supply stores. Examples: Grainger part # 1D237, or available online at www.squared.com
part # QO120HM.
GROUNDING INSTRUCTIONS
This product must be grounded. If the treadmill should malfunction or breakdown, grounding provides a path
of least resistance for electric current, reducing the risk of electric shock. This product is equipped with a cord
having an equipment-grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly
grounded. Do not modify the plug provided with the product if it will not fit the outlet; have a proper outlet
installed by a qualified electrician.
This product is for use on a nominal 230-volt circuit, and has a grounding plug that looks like the plug
illustrated below. A temporary adapter that looks like the adapter illustrated below may be used to
connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly grounded outlet, (shown below) can be installed
by a qualified electrician. The green colored rigid ear-lug, or the like, extending from the adapter, must be
connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is
used, it must be held in place by a metal screw.
4
IMPORTANT OPERATION INSTRUCTIONS
NEVER operate this treadmill without reading and completely understanding the
results of any operational change you request from the computer.
Understand that changes in speed and incline do not occur immediately. Set your
desired work level on the computer console and release the adjustment key. The
computer will obey the command gradually.
NEVER use your treadmill during an electrical storm. Surges may occur in your
household power supply that could damage treadmill components. Unplug the
treadmill during an electrical storm as a precaution.
Use caution while participating in other activities while walking on your treadmill;
such as watching television, reading, etc. These distractions may cause you to lose
balance which may result in serious injury.
Do not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure.
SAFETY TETHER CORD
A safety tether cord is provided with this unit. It is a simple magnetic design that
should be used at all times. It is for your safety should you fall or move too far back on
the tread-belt. Pulling this safety tether cord will stop tread-belt movement.
To Use:
1. Place the magnet into position on the round metal portion of the console control head.
Your treadmill will not start and operate without this. Removing the magnet also
secures the treadmill from unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note:
The magnet has strong enough power to minimize accidental, unexpected stopping.
The clip should be attached securely to make certain it does not come off. Be familiar
with its function and limitations. The treadmill will stop, depending on speed, with a
one to two step coast anytime the magnet is pulled off the console. Use the Stop /
Pause switch in normal operation.
5
ASSEMBLY INSTRUCTIONS
!!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ
BEFORE UNPACKING YOUR FOLDING TREADMILL!!
Serious injury could occur if this folding treadmill is not unpacked properly.
There is a Velcro strap installed around the treadmill base that prevents the treadmill
from unfolding accidentally during shipping. If this strap is not removed properly the
treadmill could spring open unexpectedly and cause injury if someone is standing near
the treadmill when the strap is removed.
To ensure your personal safety during removal of the shipping strap please make sure
the treadmill is positioned flat on the ground, in the orientation it would be in if you were
using the treadmill. Do not turn the treadmill up on its side while removing the shipping
strap. This could cause the treadmill’s folding mechanism to spring open. If the end of
the Velcro strap (that you need to grab to remove it) happens to be under the treadmill
deck, reach under the deck to grab it, but do not tilt the treadmill up to gain access to
the strap end.
Cut the banding straps with a short box cutter (razor knife); separate the carton from the
one underneath it by prying up on the staples (if applicable). Pull the carton over the
treadmill parts and locate the hardware pack. The hardware pack is separated into five
sections; one section containing tools and four sections labeled steps 1-4 which contain
the hardware needed for assembly of each step. The assembly steps below are
numbered one through four and correspond to the hardware in the numbered sections
of the hardware pack. Remove only the hardware for the step you are currently
assembling to avoid confusion and mix ups.
Then remove the treadmill from the carton and lay it on a level surface.
ASSEMBLY TOOLS
#
1
07
.
Combination M5 Allen Wrench
& Phillips Head Screw Driver #109. Phillips Head Screw Driver #18. Deck/Belt Lubricant
#106. M6 Allen Wrench #63. Safety Key
6
UPRIGHT TUBE ASSEMBLY
1. Slide the bottom console covers onto the console mast tubes (52 onto 5 Left side & 53 onto 4
Right side). Make sure they are oriented as shown in the illustration.
2. Connect computer cables (32 & 33) on the right side.
3. Insert console mast tubes (4 & 5) into the frame. Caution: Be careful not to pinch the cables you
just connected. Doing so could affect the console function. Pull the end of the cable tight as
you insert the right console mast tube.
4. Insert three Button Head Socket Bolts (102) and one Button Head Socket Bolt (103) and Split
Washer (108) on each side. Partially tighten these using the M6 Allen Wrench (106). Don’t
completely tighten these until the end of step 3.
HARDWARE
1
#
102
. 5/16” x 15mm
Button Head Socket
Bolt (6 pcs)
#
108
. 3/8” x 2T
Split Washer
(2 pcs)
#
103
. 3/8” x 2”
Button Head Socket
Bolt (2 pcs)
7
8
CONSOLE ASSEMBLY
1. Connect the following cables together: Incline cables 35 to 39, Speed cables 34 to 38, and
Computer cables 33 to 31.
2. Place the console (37) onto the brackets at the top of the console mast tubes and attach with two
Button Head Bolts (104) and two Split Washers (108) on each side. Caution: Be careful not to
pinch any of the cables. Doing so may affect the console function. Firmly tighten with the
Combination M5 Allen Wrench & Phillips Head Screw Driver (107).
HARDWARE
2
#
108
. 3/8” x 2.0T
Split Washer (4 pcs)
#
104
. 3/8” x 1
-
3/4”
Button Head Socket
Bolt (4 pcs)
9
BASE COVERS
1. Attach the bottom console covers (52 & 53) to the console with five Sheet Metal Screws (105)
on each side. Tighten with the Phillips Head Screw Driver (109) or Combination M5 Allen
Wrench & Phillips Head Screw Driver (107).
2. Attach the cross brace (3) to the console mast tubes (4 & 5) with two Button Head Socket Bolts
(102) on each side. Tighten with the M6 Allen Wrench (106).
3. Firmly tighten the eight Button Head Socket Bolts inserted in Step 1 with the M6 Allen Wrench
(106). Place the accessory holder tray (48) securely on top of the cross brace (3).
HARDWARE
3
#
102
. 5/16” x 15mm
Button Head Socket
Bolt (4 pcs)
#
105
. 3.5 x 12mm
Sheet Metal Screw
(10 pcs)
10
PLASTIC PARTS ASSEMBLY
1.
Place two M5 Speed Nut Clips (84) onto each side of the frame.
2. Attach the side covers (40 & 41) to the frame with one Self Tapping Screw (146) and three Self
Tapping Screws (147) on each side. Refer to the illustration for screw placement. Tighten with the
Phillips Head Screw Driver (109).
HARDWARE
4
#
146
. 5 x 16mm
Self Tapping Screw
(2 pcs)
#
84
. Speed Nut
Clips (4 pcs)
#
147
. 5 x 16m
m
Sheet Metal Screw
(6 pcs)
11
TRANSPORTATION INSTRUCTIONS
Carefully lift the treadmill at the rear roller area, grasping the two end caps, and
roll the treadmill away.
12
FEATURES
HANDRAIL ADJUSTMENTS
The treadmill allows you to make speed and incline
changes on the side handrails. You can also choose to turn
these off if you frequently hold on to these rails. This is
achieved by pressing the disable button on the right side of
the lower portion of the console.
QUICK SPEED & INCLINE BUTTONS
You are able to set your speed and incline settings quickly by using the quick keys
on the console. Just press either Speed or Incline, then select either 1 or 2 digits
and the treadmill will automatically adjust to that value. This saves time because you
don’t have to press and hold or hold a button down until reaching the desired value.
The maximum value you may input for speed is 9.9 mph or kmph and incline 9.5%
Examples: Press the Quick Incline button, then 1, 0 = Incline Level 1.0
Press the Quick Incline button, then 3, 5 = Incline Level 3.5
Press the Quick Speed button, then 8, 0 = 8.0 mph or kmph
Press the Quick Speed button, then 0, 8 = 0.8 mph or kmph
CONSOLE
MUSCLE ACTIVATION FIGURE
There is an anatomical figure located at the top of the console. This figure will light
all areas that are activated when using the treadmill. These will light up during any of
the programs. You can control which muscles are activated by changing the incline and
swinging your arms. The pre-set programs will determine which lower body muscles
will be activated by automatically adjusting the incline. Generally the following
guidelines hold true:
The upper body LED’s will light any time your hands aren’t in contact with the pulse grip sensors
The lower body lights will activate in three degrees of engagement: Green represents minimal
muscle involvement, Amber represents medium involvement, and Red represents full or heavy
activation.
0-4.5% Elevation: even muscle distribution, all four
muscle groups will be Amber
5-15% Elevation: Quads are Amber and Glutes,
Hamstrings and Calves are Red
13
The console will display Pace, Calories burned, Time (elapsed or
countdown), Distance travelled, Pulse, Speed, Incline, Program
Name, # of Laps completed, and Segment Time. There is also a
Speed & Incline profile graph that lets you see how hard you have
worked and how challenging the upcoming segments will be.
HEART RATE BAR GRAPH
The console LCD screen will display your current heart rate anytime
a pulse is detected. The Bar Graph, located to the right of the LCD
screen, will show your current heart rate % in relation to your
projected maximum heart rate, which is determined by your age that
you entered during the programming phase of any of the 12
programs. The significance of the bar graph colors are as follows:
50-60% of maximum is Amber
65-80% of maximum is Amber and Green
85-95% or more is Amber, Green, and Red
14
OPERATION OF YOUR CONSOLE
GETTING FAMILIAR WITH THE CONTROL PANEL
CONSOLE
GETTING STARTED
Power the treadmill on by plugging it into an appropriate wall outlet, then turn on the
power switch located at the front of the treadmill below the motor cover. Ensure that
the safety key is installed, as the treadmill will not power on without it.
When the power is turned on, all the lights on the display will light for a short time.
Then the Time and Distance windows will display Odometer readings for a short
time. The Time window will show how many hours the treadmill has been in use and
the Distance window will show how many miles (or Kilometers if the treadmill is set
to metric readings) the treadmill has gone. Then a message is the message center
will show the current software version. The treadmill will then enter idle mode, which
is the starting point for operation.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw U.N.O. TR 4.0 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van U.N.O. TR 4.0 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van U.N.O. TR 4.0

U.N.O. TR 4.0 Gebruiksaanwijzing - Français - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info