Manufacturer’s
terms of warranty
1. Case of warranty
The manufacturer grants a
warranty for malfunctions in
the appliance which are
based on material or produc-
tion faults. In addition to this,
the statutory warranty claims
against the seller remain
valid.
A claim under warranty shall
not pertain:
- for parts subject to wear and
in cases of natural wear and
tear,
- as a result of not original
Truma parts being used in
the appliance and as a result
of unsuitable gas pressure
regulators being used,
- as a consequence of failure
to respect Truma instruc-
tions for installation and use,
- as a consequence of im-
proper handling,
- as a consequence of im-
proper transport packing,
not arranged by Truma.
2. Scope of warranty
The warranty is valid for mal-
functions as stated under
item 1, which occur within
24 months after conclusion of
the purchase agreement be-
tween the seller and the final
consumer. The manufacturers
will make good such defects
by subsequent fulfilment, i.e.
at their discretion either by re-
pair or replacement. In the
event of manufacturers pro-
viding service under warranty,
the term of the warranty shall
not recommence anew with
regard to the repaired or re-
placed parts; rather, the old
warranty period shall continue
to run. More extensive claims,
in particular claims for com-
pensatory damages by pur-
chasers or third parties, shall
be excluded. This does not af-
fect the rules of the product
liability law.
The manufacturer shall bear
the cost of employing the
Truma customer service for
the removal of a malfunction
under warranty - in particular
transportation costs, travelling
expenses, job and material
costs, as long as the service
is carried out in Germany.
Customer service carried out
abroad is not covered by the
warranty.
Additional costs based on
complicated removal and in-
stallation conditions of the
appliance (e.g. removal of
furniture or parts of the vehi-
cle body) do not come under
warranty.
3. Raising the case of
warranty
The address of the manufac-
turers is: Truma Gerätetech-
nik GmbH & Co. KG, Wern-
her-von-Braun Strasse 12,
D-85640 Putzbrunn. In Ger-
many, in the event of faults,
in principle the Truma Ser-
vice Centre at the manufac-
turers' address is to be noti-
fied; abroad, respective ser-
vice partners are available
(refer to address list). Com-
plaints must be specified. In
addition, the correctly com-
pleted warranty certificate
must be presented or the Se-
rial number of the appliance
and the date of purchase
specified.
In order for the manufactur-
ers to be able to determine
whether an incident subject
to guarantee has occurred,
the end user must, at his
own risk, bring the device to
the manufacturers or send it
to them. If there is damage
to heaters (heat exchangers),
the gas pressure regulator
must also be sent back to
the factory.
In instances of the device be-
ing sent to the works, dis-
patch is to be effected by
freight transport. In cases
under guarantee, the works
shall bear the transport costs
or the costs of delivery and
return. If the damage is
deemed not to be a warranty
case, the manufacturer shall
notify the customer and shall
specify repair costs which
shall not be borne by the
manufacturer; in this case,
the customer shall also bear
the shipping costs.
5
Conection 230 V
with specific vehicle
or manufacturer
control panels
Connect control panel cable,
230 V cable and heating ele-
ment cable as shown in the
drawing.
Cables must be in accor-
dance with the technical rules
and regulations of the coun-
try in which the vehicle is to
be registered, for the first
time (e.g. in Germany VDE
0100, section 721).
7
Gas connection
Fig. A: The 8 mm gas supply
line is connected to the con-
nection nozzle (38) with cut-
ting ring connection. The cut-
ting rings are to be selected
according to the gas pipe
used (for copper pipe: sup-
port sleeves and brass cutting
ring as supplied). Carefully
hold in place with a second
wrench when tightening!
Before connecting to the wa-
ter heater make sure that the
gas lines are free from dirt,
chips and such!
Route the pipes in such a way
that the appliance can be re-
moved again for servicing.
In areas frequented by peo-
ple, keep the number of part-
ing connections in the gas
supply line to an technically
feasible minimum.
The gas system must comply
with the technical and admin-
istrative regulations of the
country in which the appli-
ance is used (in Germany, for
example, the DVGW form
G 607).
supply line
230 V
3 x 1,5 mm
2
heating
element
splitting box
control panel
PEL
N
N’ L’
8
Function check
After installation, check gas
supply line for leaks in accor-
dance with the pressure drop
method. Following this,
check the function of the ap-
pliance as specified in the op-
erating instructions, check
the function of the draining of
the water contents, in partic-
ular. There shall be no
claims under guarantee for
damage caused by frost!
Never operate the water
heater without water con-
tents. It is, however, possible
to briefly check the electrical
function without water con-
tents. Always observe the op-
erating instructions prior to
operation!
The operating instructions
and completed guarantee
card are to be given to the
owner of the vehicle.
9
Warning information
The installer or vehicle owner
must apply the yellow sticker
with the warning information,
which is enclosed with the
appliance, to a place in the
vehicle where it is clearly visi-
ble to all users (e.g. on the
wardrobe door)! Ask Truma to
send you stickers, if neces-
sary.
