484649
23
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
23
Safety socket connection with conventional
brake lights
(applies to 7-pin and 13-pin sockets!)
The fact that there are two conventional brake lights and
a third brake light with LED technology does not affect
this connection.
Route the provided 2-wire cable (10 m) with the wire-end fer-
rules through the socket holder (g) and the rubber sleeve (h).
Open cover and push socket connection out of socket hous-
ing (i).
Connect wire with longitudinal red stripe to pin 6 and black
wire to pin 3 (pin designation printed on connection and on
inside of cover).
Re-insert socket connection into socket housing (i).
Screw socket housing (i) to socket holder (g) using 3 sheet
metal screws (j). (Several alternative positions are available by
using the mounting holes in the socket holder and rotating
the rubber seal.)
Loosely route cable through strain relief (k) and secure with
2 sheet metal screws. Depending on the installation situation,
the cable can be led out of the socket holder through one of
the three recesses.
j
B 3.9 x 33
(3 x)
i
h
Pin 3
Pin 6
g
PT 4 x 10
k
Secure safety socket to the (plastic) shaft cover of the cara-
van with 4 bolts, nuts and washers.
M4 x 16
(4 x)
Washer 4,3
(4 x)
Nut M4 (4 x)
No holes must be drilled in the chassis.
Alternatively, the safety socket can be secured using the two
worm drive hose clamps.
Route wire connected to pin 6 (with red stripe) to control unit
(shorten if necessary), crimp on a flat plug and connect as
shown in the connecting diagram.
Route wire connected to pin 3 (black) to control unit (shorten
if necessary), crimp on a ring and screw to negative battery
terminal as shown in connecting diagram.
The connection to the control unit must be made in the
order – nut, battery negative terminal ring, nut, cable
pin 3 ring, nut.
Re-check whether all cables are correctly connected, attached
using the provided clips and cannot chafe.
Safety socket connection with LED brake lights
This connection must always be used if all brake lights
are of the LED variety! With two conventional brake
lights and a third brake light with LED technology, the connec-
tion is made as described in “Safety socket connection with
conventional brake lights”.
7-pin safety socket
Connect pin 3 of the caravan plug to the negative battery
terminal.
Connect pin 3 of the safety socket to the controller
(with one wire of the 2-wire cable).
13-pin safety socket
Connect pin 11 of the caravan plug to the negative battery
terminal.
Connect pin 11 of the safety socket to the controller
(with one wire of the 2-wire cable).
If it is not possible to make a connection using pin 11 (pin
missing, for example), use pin 3 as an alternative.
It must be ensured that ground connections pin 11
and pin 3 are not interconnected in an electrically
conductive manner at the trailer side!
Connecting diagram with LED brake lights
1
+
-
Safety
socket
Engagement
motors
Drive
motor
Drive-
motor
Battery
1
– + – +
– +
234
Caravan
plug
13-pin
3
11
8
1
2
97
5
4
6
10
1213
7-pin
3
4
6
7
1
5
2
11
3
8
1
2
97
5
4
6
10
1213
6
4
7
1
5
2
3
Safety
contact
Fuse
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Truma Mover Mover TE R4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Truma Mover Mover TE R4 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Deens als bijlage per email.

De handleiding is 12,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info