489376
21
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
21
Location selection
After installation of the air-conditioning system, any ex-
isting exhaust cowl nearby must extend at least 10 cm
over the air-conditioning system. The exhaust cowl must be
extended if necessary (pay attention to the heater manufactur-
er‘s information).
The vehicle roof (roof thicknesses from 25 to 110 mm) must
be level and smooth.
There are 3 installation options:
A new cut-out has to be made (350 x 380 mm).
Cut-out from an existing skylight (400 x 400 mm) without
sealing frame (accessories).
Cut-out from an existing skylight (400 x 400 mm) with seal-
ing frame (accessories) (Operating instructions are supplied
with the sealing frame.)
Please always take the following requirements into
account:
If at all possible, the unit should only be installed a little way
from the centre of the vehicle.
Check that installation will not be obstructed in any way.
There may be electrical cables running between the inside
and the outside of the roof. Disconnect all voltage sources
before starting work (all poles).
The maximum permitted roof load must not be exceeded
(see the vehicle manufacturer‘s specification).
Check the internal installation location for obstructions.
A wooden reinforcement frame must be fitted around
the cut-out in the roof between the upper and lower roof
surface (min. 25 mm). It may be necessary to remove the
insulation.
Installation in a 400 x 400 cut-out
For optimum sealing, we recommend using the sealing frame
which can be purchased as an accessory (part no. 40091-19000).
Installation with the sealing frame is described in the installa-
tion instructions supplied with it.
Installation of the unit in vehicles with an existing skylight:
The cut-out must measure 400 x 400 mm.
Remove the existing skylight (increase the size of the cut-out
if necessary).
Remove seal residue and unevenness.
Fill screw holes with body sealant.
400
400
For the remaining installation steps, please refer to “Prepara-
tion for mains cable connection”.
Installation in a new cut-out
Vehicles without an existing cut-out:
required cut-out 350 x 380 mm
Place the template in the installation location on the vehicle
and mark and cut out the cut-out (350 x 380 mm).
Mark out the 4 holes (10 mm) for attaching the brackets and
drill through the roof.
380
350
Preparation for mains cable connection
A leadthrough for the mains cable to the connection point
should be provided in the intermediate ceiling, for example.
Lift the unit onto the roof, holding it in a horizontal position,
and insert it into the cut-out. The arrow points in the vehicle‘s
direction of travel.
If the unit has been turned over or was not horizontal at
all times, you must wait 2 hours before switching it on.
Slide the unit forward in the cut-out as far as it will go.
Remove the protective film.
21

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Truma-Aventa-comfort

Zoeken resetten

6

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Truma Aventa comfort bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Truma Aventa comfort in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Deens als bijlage per email.

De handleiding is 3,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info