726880
6
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
TRT-BA-TTR57E-TC2018-46-002-EN
TTR 57 E
EN
OPERATING MANUAL
DEHUMIDIFIER
2 EN
dehumidifier TTR 57 E
Table of contents
Notes regarding the operating manual.................................2
Safety .....................................................................................2
Information about the device................................................4
Transport and storage...........................................................5
Assembly and installation.....................................................6
Operation ...............................................................................7
Available accessories..........................................................10
Errors and faults..................................................................11
Maintenance ........................................................................12
Technical annex...................................................................15
Disposal ...............................................................................19
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
TTR 57 E
https://hub.trotec.com/?id=42658
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
Do not use the device in potentially explosive rooms.
Do not use the device in aggressive atmosphere.
Set the device up in an upright and stable position.
Let the device dry out after a wet clean. Do not operate it
when wet.
Do not use the device with wet or damp hands.
Do not expose the device to directly squirting water.
Never insert any objects or limbs into the device.
Do not cover or transport the device during operation.
Do not sit on the device.
This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
EN 3
dehumidifier TTR 57 E
Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
The electrical connection must correspond to the
specifications in chapter Technical data.
Insert the mains plug into a properly secured mains
socket.
Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
Make sure that the air inlet and outlet are not obstructed.
Make sure that the suction side is kept free of dirt and
loose objects.
Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
Only transport the device in an upright position with an
emptied condensation tank or drain hose.
Discharge the collected condensate before transport and
storage. Do not drink it. Health hazard!
Intended use
Only use the device for drying and dehumidifying room air, while
adhering to and following the technical data.
In addition, the device may also be used as a kind of clothes
dryer to dry wet laundry.
Intended use comprises:
dehumidifying and drying:
living rooms, bedrooms, bathrooms and basements
laundries, holiday homes, camper vans, boats
maintaining the dryness of:
storage spaces, archives, laboratories, garages
bathrooms, wash rooms, changing rooms etc.
Improper use
The device is not intended for industrial use.
Do not place the device on wet or flooded ground.
Do not place any objects, e.g. clothing, on the device.
Do not use the device outdoors.
Any unauthorised modifications, alterations or structural
changes to the device are forbidden.
Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Personnel qualifications
People who use this device must:
be aware of the dangers that occur when working with
electric devices in damp areas.
have read and understood the operating manual, especially
the Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist companies for cooling and
air-conditioning or by Trotec.
4 EN
dehumidifier TTR 57 E
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Note
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
Behaviour in the event of an emergency
1. Switch off the device.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
Information about the device
Description of the device
The TTR57E operates on the desiccant principle, without
compressor or refrigerant.
The fully automatic control and the condensation tank with
integrated overflow protection ensure fault-free operation.
The fan sucks in damp room air via the air inlet with air filter,
the condenser and the desiccant wheel located behind it.
Within the internal regeneration circuit the air is led via a
heating element, it dries the desiccant wheel and leads the
moist, warm air through the condenser. At the cooler
condenser, heat is withdrawn from the room air and cooled
below dew point. The water vapour contained in the room air
precipitates in form of condensate. The condensate drops into
the condensation tank. Optionally, the condensate can be
discharged via a condensation hose connected to the
connection opening.
The drier air, thus conditioned, is fed back to the room air via
the air outlet. The drier air mixes with the air in the room. The
relative humidity in the room where the device is positioned is
reduced by the constant circulation of the room air.
A float is attached inside the condensation tank, which in case
of a filled condensation tank interrupts the dehumidification.
When switching off, the device emits an acoustic signal and the
Tank Full LED on the control panel is illuminated (see chapter
Operating elements). The indicator light only goes out again
once the emptied condensation tank is reinserted.
The device can reduce the relative humidity of a room to
approx. 40%.
In addition, the device may also be used as a kind of clothes
dryer to dry wet laundry.
EN 5
dehumidifier TTR 57 E
Device depiction
2
1
3
4
5
1
2
6
7
8
5
3
No. Designation
1 Control panel
2 Handle
3 Air outlet
4 Colour LEDindication for humidity level
blue=humidity >70%
green=humidity50%–70%
red=humidity<50%
5 Condensation tank
6 Air inlet with air filter
7 Power cable
8 Connection opening for condensation hose
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a carry
handle.
Before transporting the device, observe the following:
Switch off the device.
Due to the follow-up time of the internal components,
the device only switches off completely after
approx. 2 minutes.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Do not use the power cable to drag the device.
Drain the remaining condensate from the device and the
condensation drain hose (see chapter Maintenance).
After transporting the device, observe the following:
Set up the device in an upright position after transport.
Leave the device to rest for one hour before switching it
back on. Otherwise the device could be damaged and no
longer work properly. Any warranty claims will be voided in
this case.
Storage
Before storing the device, proceed as follows:
Drain the remaining condensate from the device and the
condensation drain hose (see chapter Maintenance).
Empty and clean the condensation tank and the
condensation drain hose prior to storage.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
When the device is not being used, observe the following
storage conditions:
dry and protected from frost and heat
in an upright position where it is protected from dust and
direct sunlight
with a cover to protect it from invasive dust, if necessary
Place no further devices or objects on top of the device to
prevent it from being damaged.
6 EN
dehumidifier TTR 57 E
Assembly and installation
Scope of delivery
1x Device
1x Air filter
1x Activated carbon filter
1x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Start-up
When positioning the device, observe the minimum distance
from walls or other objects as described in the Technical data
chapter.
A
B
C
C
D
Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
Set the device up in an upright and stable position.
Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
Make sure that extension cables are completely unrolled.
When positioning the device, keep a sufficient distance to
heat sources.
Make sure that no curtains or other objects interfere with
the air flow.
When positioning the device, particularly in wet areas,
secure it locally with an RCD (residual current device)
which complies with the respective regulations.
Notes regarding the dehumidification performance
The dehumidification performance depends on:
the layout of the room
the room temperature
the relative humidity
The higher the room temperature and relative humidity, the
greater the dehumidification performance.
For use in living rooms, a relative humidity of approx. 50 to
60% is sufficient. In storage facilities and archives, the
humidity should not exceed approx. 50%.
Inserting the air filter
Note
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
Make sure that the air filter is installed before switching
the device on.
26256
No. Operating element
6 Air filter
25 HEPA filter (optional)
26 Activated carbon filter
EN 7
dehumidifier TTR 57 E
Opening the ventilation flaps
1. Prior to switching the device on, open the ventilation flaps
at the air outlet.
Inserting the condensation tank
Ensure that the float inside the condensation tank is
inserted correctly.
Ensure that the condensation tank is empty and inserted
correctly.
Connecting the power cable
Insert the mains plug into a properly secured mains
socket.
Operation
After being switched on, the device operates fully
automatically – depending on the selected operating mode
or until the float indicates that the condensation tank is full
and the device switches itself off.
Avoid open doors and windows.
Operating elements
16 17 18 19 20
21
22
23
24
13
14
15
9 10 11 12
No. Designation Meaning
9 low LED Indication of low fan speed
10 med LED Indication of medium fan speed
11 high LED Indication of high fan speed
12 Segment display Indicates the room temperature
(0 to 50°C)
Indicates the ambient air's relative
humidity (35% to 95%RH)
Indicates the set humidity level when
pressing the Humidity button
Indicates the preselected hours for
approx.8seconds when pressing the
Timer button
13 Speed button Sets the fan speed
14 On LED Illuminated in green = operation
indication
Flashes red = device tilted (over)
15 Drying LED Laundry drying mode indication
16 Drying button Starts laundry drying mode
17 Humidity button Sets the target humidity value:
continuous operation (CO), 40%, 50%,
60%, 70%
18 On/Off button Switches the device on or off
19 Timer button Starts programming the timer function
20 Ventilation
button
Starts ventilation mode
8 EN
dehumidifier TTR 57 E
No. Designation Meaning
21 Auto button Starts automatic mode
> 70% RH = high fan speed
55%–70% RH = low fan speed
< 55% RH = The device switches off for
30minutes and will then check the
relative humidity level again
Automatic start-up at more than
55%RH
22 Tank Full LED Condensation tank full or not positioned
correctly indication
23 Timer LED Timer function indication
24 Ventilation LED Ventilation mode indication
Switching the device on
Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.
Note
Wait for 3 minutes before you switch the device back
on (e.g. after draining the condensation tank).
1. Use the On/Off button(18) to switch the device on.
ð The device starts to dehumidify.
Setting the operating mode
Ventilation mode
The device can be set to three fan speeds: low, med and high.
Low:
The device operates at a low fan speed and low heating
capacity to save energy and keep the operating noise to a
minimum. The heating switches off when the relative humidity
in the ambient air falls below the set nominal value. If the
humidity increases to above the set value, the heating will
switch on again. The indication for the room humidity level on
the front of the device is deactivated.
Med:
The device operates at normal fan speed and high heating
capacity.
High:
The device operates at high fan speed and high heating
capacity.
Select the fan speed as follows:
1. Press the Speed button(13) until the low LED(9) is
illuminated.
2. Repeatedly press the Speed button(13) until the
med LED(10) is illuminated.
3. Repeatedly press the Speed button(13) until the
high LED(11) is illuminated.
Setting the desired relative room humidity
You can adjust the desired relative room humidity. The selected
room humidity level is indicated on the segment display(12).
You can select the following settings: (CO), 40%,50%,60%
and 70%. To do so, please proceed as follows:
1. Press the Humidity button(17).
ð The selected room humidity level is indicated on the
segment display(12).
2. Press the Humidity button(17) again until the desired value
is shown on the segment display(12).
Continuous operation
The device dehumidifies the air constantly and regardless of the
relative humidity.
The desired relative room humidity cannot be adjusted in this
operating mode.
1. Use the On/Off button(18) to switch the device on.
2. Press the Humidity button(17) until the segment
display(12) shows continuous operation(CO).
For reasons of safety, the device switches off automatically for
30minutes after 8hours of continuous operation. After the
30minutes have passed, the cycle starts again and the device
switches back on for another 8hours.
Ambient temperature above 36°C
If the ambient temperature exceeds 36°C, the heating switches
off for 30minutes while the fan keeps running. After the
30minutes have passed, the device checks the room humidity
and temperature. If the room humidity is higher than the
previously selected value, the device switches back on for
another 8hours. If the room humidity is lower than this value or
if the ambient temperature is higher than 36°C, the device
switches off again for another 30minutes.
EN 9
dehumidifier TTR 57 E
Colour LED for current room humidity
Regardless of the operating mode, the colour LED indicates the
current relative room humidity by means of 3 different colours.
LED colour Meaning
Blue
Relative room humidity above
70%
Green
Optimal relative room humidity
between 50% and 70%
Red
Relative room humidity below
50%
Setting the timer
For the device to switch on or off automatically after a
predefined number of hours (1 to 24) you can programme the
timer.
The timer can be programmed in increments of 1hour (1to
24h).
Note
Do not leave the operating device unattended in a
freely accessible room with an activated timer.
Automatic switch-on
1. Switch the device off.
2. Press and hold the Timer button(19) until the segment
display(12) shows the desired duration in hours.
ð The Timer LED(23) is illuminated.
ð The number of hours is shown on the segment
display(12).
ð After the predefined time, the device switches itself on.
Automatic switch-off
ü The device is switched on.
1. Press and hold the Timer button(19) until the segment
display(12) shows the desired duration in hours.
ð The Timer LED(23) is illuminated.
ð The number of hours is shown on the segment
display(12).
ð After the predefined time, the device switches itself off.
Operation with hose attached to the condensation
connection
At a high humidity level it is recommendable to constantly drain
the condensate via a hose, for otherwise the condensation tank
has to be emptied too frequently.
To do so, proceed as follows:
ü A suitable hose (diameter: 11mm) is ready for use.
ü The device is switched off.
1. Remove the condensation tank(5).
2. Push one end of the hose onto the hose connection.
10 EN
dehumidifier TTR 57 E
3. Put the condensation tank(5) back in.
4. Guide the other hose end to a suitable drain or sufficiently
dimensioned collection container. Please note that the
hose must not be kinked.
Drying laundry
In addition, the device may also be used as a kind of clothes
dryer to dry wet laundry in living or working spaces.
When positioning the device or a clothes horse, please observe
the minimum distances specified in the technical data.
For drying laundry the following values should be selected:
cupboard dry = 46 % relative humidity
iron dry = 58 % relative humidity
slightly dried = 65 % relative humidity
If necessary, use a measuring device to determine the humidity
level.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch off the device.
Wait for approx. 2 minutes.
Due to the follow-up time of the internal components,
the device only switches off completely after
approx. 2 minutes.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Empty the condensation tank, if need be.
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Available accessories
Warning
Only use accessories and additional equipment
specified in the operating manual.
Using insertion tools or accessories other than those
specified in the operating manual may cause a risk of
injury.
Designation Article number
HEPA filter TTR 57 E 7.710.000.051
EN 11
dehumidifier TTR 57 E
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damage.
Check the on-site fusing.
Check the condensation tank for correct seating.
The device comes equipped with a tilt protection, it
switches off automatically when tilted. The On LED(14) is
illuminated in green during operation. When On LED(14)
flashes red, check whether device is in an upright position
on a level surface.
Check the room temperature. Observe the device's
permissible operating range according to the technical
data.
At an ambient temperature above 36°C, the heating is
switched off automatically making condensate formation
impossible.
Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device is running, but there is no formation of
condensate:
Check the float in the condensation tank for dirt. If
necessary, clean the condensation tank. The float must be
able to move freely.
Check the room temperature. Observe the device's
permissible operating range according to the technical
data.
Ensure that the relative room humidity complies with the
technical data.
Check the air filter for dirt. If necessary, clean or replace
the air filter.
From the outside, check the condenser for dirt (see
chapter Maintenance). If the condenser is dirty, have it
cleaned by a specialist company or by Trotec.
The device is loud or vibrates:
Check whether the device is set up in a stable and upright
position.
Condensate is leaking:
Check the device for leaks.
The device gets very warm, is loud or loses power:
Check the air inlets and air filters for dirt. Remove external
dirt.
From the outside, check the device for dirt (see chapter
Maintenance). If the inside of the device is dirty, have it
cleaned by a specialist company for cooling and air-
conditioning or by Trotec.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to a specialist company for cooling and air-conditioning
or to Trotec for repair.
12 EN
dehumidifier TTR 57 E
Maintenance
Maintenance intervals
Maintenance and care interval before every
start-up
as needed at least every
2weeks
at least every
4weeks
at least every
6months
at least
annually
Check the air inlets and outlets for dirt
and foreign objects and clean if
necessary
X X
Clean the exterior
X X
Visually check the inside of the device
for dirt
X X
Check the air filter for dirt and foreign
objects and clean or replace if necessary
X X
Replace the air filter
X
Check for damage
X
Check the attachment screws
X X
Test run
X
Empty the condensation tank and/or
drain hose
X
Maintenance and care log
Device type: .............................................
Device number: ....................................
Maintenance and care interval
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Check air inlets and outlets for dirt and
foreign objects and clean if necessary
Clean the exterior
Visually check the inside of the device
for dirt
Check the air filter for dirt and foreign
objects and clean or replace if necessary
Replace the air filter
Check for damage
Check the attachment screws
Test run
Empty the condensation tank and/or
drain hose
Comments
1. Date: ...........................................
Signature: ........................................
2. Date: ............................................
Signature: .........................................
3. Date: .............................................
Signature: .........................................
4. Date: .............................................
Signature: .........................................
5. Date: ...........................................
Signature: ........................................
6. Date: ............................................
Signature: .........................................
7. Date: .............................................
Signature: .........................................
8. Date: .............................................
Signature: .........................................
9. Date: ...........................................
Signature: ........................................
10. Date: ..........................................
Signature: .........................................
11. Date: ...........................................
Signature: .........................................
12. Date: ...........................................
Signature: .........................................
13. Date: .........................................
Signature: ........................................
14. Date: ..........................................
Signature: .........................................
15. Date: ...........................................
Signature: .........................................
16. Date: ...........................................
Signature: .........................................
EN 13
dehumidifier TTR 57 E
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch the device off.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down completely.
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
Cleaning the housing
Clean the housing with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Visual inspection of the inside of the device for dirt
1. Remove the air filter.
2. Use a torch to illuminate the openings of the device.
3. Check the inside of the device for dirt.
4. If you see a thick layer of dust, have the inside of the
device cleaned by a specialist company for cooling and air-
conditioning or by Trotec.
5. Put the air filter back in.
Cleaning the air filter
Note
Ensure that the air filter is not worn or damaged. The
corners and edges of the air filter must not be
deformed or rounded. Before reinserting the air filter,
make sure that it is undamaged and dry!
Note
Neither the activated carbon filter nor the HEPA
filter(optional) can be cleaned. Both filters must be
replaced if required.
The air filter has to be cleaned as soon as it is dirty. This is
brought to light e.g. by a reduced capacity (see chapter Errors
and faults).
The lifetime of the activated carbon filter or HEPA filter depends
on the ambient conditions and the application period of the
device.
1. Remove the air filter from the device.
2. Clean the filter using a slightly damp, soft, lint-free cloth. If
the filter is heavily contaminated, clean it with warm water
mixed with a neutral cleaning agent.
14 EN
dehumidifier TTR 57 E
3. Allow the filter to dry completely. Do not insert a wet filter
into the device!
4. Reinsert the air filter into the device.
Emptying the condensation tank
When the condensation tank(5) is full or not inserted correctly,
the device stops dehumidification operation and switches itself
off. The Tank Full LED(22) lights up and an acoustic signal is
emitted.
1. Take the condensation tank(5) out of the device.
2. Empty the condensation tank(5) over a drain or sink.
3. Rinse the condensation tank(5) with clear water. Regularly
clean the condensation tank(5) using a mild cleaning
agent (no dish detergent!).
4. Refit the condensation tank(5) into the device. Make sure
not to damage the float when inserting or removing the
condensation tank(5).
ð In doing so, make sure that the float is positioned
correctly.
ð In doing so, make sure that the condensation tank(5) is
inserted correctly, for otherwise the device cannot be
switched back on.
Activities required after maintenance
If you want to continue using the device:
Leave the device to rest for one hour before switching it
back on. Otherwise the device could be damaged and no
longer work properly. Any warranty claims will be voided in
this case.
Reconnect the device to the mains.
If you do not intend to use the device for a considerable time:
Store the device according to the Storage chapter.
EN 15
dehumidifier TTR 57 E
Technical annex
Technical data
Parameter Value
Model TTR 57 E
Max. dehumidification
performance
9 l/ 24h
Dehumidification performance
@ 30°C and 80%RH
8.5l
Air flow rate 185 m
3
/h
Operating range (temperature) 1°C to 32°C
Operating range (relative
humidity)
35% to 90%
Mains connection 1/N/PE~220 –240V/50Hz
Max. power input 730 W
Heating capacity of heating
element
650W
Nominal current consumption 3.7A
On-site fusing 10 A
Condensation tank capacity 5 l
Sound pressure level 47 dB(A)
Dimensions
(length x width x height)
340x 232x 511 mm
Minimum distance to walls and
other objects
A: top
B: rear
C: side
D: front
60 cm
20 cm
20 cm
50 cm
Weight 7.5 kg
16 EN
dehumidifier TTR 57 E
Wiring diagram
EN 17
dehumidifier TTR 57 E
Overview of spare parts
Note: The position numbers of the spare parts differ from those
describing the positions of other parts mentioned in this
operating manual.
18 EN
dehumidifier TTR 57 E
No. Spare Part No. Spare Part No. Spare Part
Plastic Parts
101 Front Plate 113 Fixer For Heat Exchanger (Down) 125 Footstand
102 Rear Plate 114 Seperating Sheet For Heat Exchanger 126 Electric Box (Top)
103 Top Plate 115 Heater Frame 127 Electric Box (Down)
104 Air Vent 116 Small Wind Funnel 128 Box For Motor Capacitor (Down)
105 Base For Dehumidifying Wheel 117 Filter Frame 129 Box For Motor Capacitor (Top)
106 Main Wind Tunnel 118 Light Indicator 130 Handle For Watertank
107 Water Tank 119 Gear (Small) 131 Float
108 Cover For Watertank 120 Bottom Base 132 Float Base
109 Water Tray 121 Silicon Blades 133 Gear (Big)
110 Top Cover For Heat Exchanger 122 Heat Exchanger (Big)/Set 134 Fan Blade (Big)
111 Bottom Cover For Heat Exchanger 123 Heat Exchanger (Small)/Set 135 Fan Blade (Small)
112 Fixer For Heat Exchanger (Up) 124 Ring Fixer 136 Fixer For Dehumidifying Wheel
Electric Parts
201 Heater 206 Fan Motor (Small) 212 Magnetic Switch
202 Dehumidifying Wheel 207 Main P.C. Board 213 Mica Sheet For Heater Sensor
203 Fan Motor (Big) 208 Control PCB 214 Fan Motor Capacitor
204 Motor Gasket 209 PCB For Light Indicator 215 Power Cord
205 Synchronous Motor 210 Humidistat Sensor 216 Magnet
Metal Parts
301 Frame For Dehumidifying Wheel 304 Frame For Heat Exchanger 307 Cover For S.Wind Funnel
302 Cover For Heater Box 305 Heater Box 308 Fixer For Dehumidifying Wheel
303 Heater Reflector 2 306 Heater Sensor Fixer
Foam Parts
501 Gasket (Big) 503 Foam For Light Block
502 Gasket (Small) 504 Water Proof Foam For Front Plate
Screws
601 Screw Set
Wires
701 Wire Set
Packing Materials
801 Carton Box 806 Active Carbon Filter 810 Instruction Manual
803 Polyfoam - Up 807 PVC Bag For Unit 811 Circuit Diagram Sticker
804 Polyfoam - Down 808 PVC Bag For I/M
805 Nameplate Sticker 809 Rating Label
EN 19
dehumidifier TTR 57 E
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Trotec TTR57E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Trotec TTR57E in de taal/talen: Engels als bijlage per email.

De handleiding is 3,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Trotec TTR57E

Trotec TTR57E Gebruiksaanwijzing - Nederlands - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Deutsch - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Français - 21 pagina's

Trotec TTR57E Gebruiksaanwijzing - Italiano - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Português - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Espanõl - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Polski - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Türkiye - 21 pagina's

Trotec TTR57E Gebruiksaanwijzing - Dansk - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Svenska - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Norsk - 20 pagina's

Trotec TTR57E Gebruiksaanwijzing - Suomi - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info