753915
15
Verklein
Vergroot
Pagina terug
1/21
Pagina verder
EN 15
angle grinder PAGS 11-125
10. Check the cutting disc(15) for proper fit.
11. Check whether the cutting disc can rotate freely. Make
sure that the disc does not touch the guard or any other
parts.
12. Carry out a test run of approx.1minute without load prior
to every disc change and every start-up in order to check
the cutting disc for correct fit.
Caution
If the disc is out-of-round, rotates unevenly, vibrates,
oscillates, or if unusual noises or sparks are generated,
the cutting disc must be exchanged immediately.
Otherwise, there is a risk of injury.
Speed selection
The required speed depends on the material and the operating
conditions and can be determined by way of field-testing. It is
recommended to use a higher speed level for cutting and
grinding harder materials, and a lower speed level for softer
materials.
The setting range covers the levels1–6 as well as the maximum
(3,000–12,000rpm).
You can change the preselected speed level at any time.
1. Turn the setting wheel(3) to the desired rated speed level.
3
Connecting the power cable
1. Insert the mains plug into a properly secured mains
socket.
Operation
Tips and notes on handling the angle grinder
General information:
Carry out a test run of approx.1minute without load prior
to every disc change and every start-up in order to check
the cutting disc for correct fit.
Only use tools which are approved for the device used.
Before every application, make sure that you have selected
the correct tool for the intended use.
Check the tool in the tool holder for proper fit before every
application. The tool must be firmly locked in place in the
designated holding fixtures on the tool holder.
Check whether the cutting disc can rotate freely. Make
sure that the disc does not touch the guard or other parts.
Only use discs with a speed imprinted that is at least as
high as the speed indicated on the device's nameplate.
Clamp the workpiece unless it is firmly and safely
positioned by its own weight.
Do not overload the device so that it comes to a standstill.
After operation at high load, let the device run at idle for
several minutes to allow the tool to cool down.
Do not touch the discs until they have cooled down.
Keep the venting slots clear to prevent the motor from
overheating.
Cutting:
Only use intact, flawless cutting discs. Bent, blunt or
otherwise damaged cutting discs could break.
Never use the cutting disc for roughing!
Only advance moderately during operation and make sure
that the cutting disc does not get jammed.
Do not slow down the decelerating cutting disc by pressing
against the side of the disc.
Always move the cutting disc through the workpiece in
reverse rotation.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Trotec PAGS 11-125 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Trotec PAGS 11-125 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Trotec PAGS 11-125

Trotec PAGS 11-125 Gebruiksaanwijzing - Nederlands - 22 pagina's

Trotec PAGS 11-125 Gebruiksaanwijzing - Deutsch - 23 pagina's

Trotec PAGS 11-125 Gebruiksaanwijzing - Français - 23 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info