727846
3
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
TRT-BA-IRD1200-IRD1800-IRD2400-IRD3200-TC2017-52-004-EN
IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
EN
OPERATING MANUAL
INFRARED RADIANT HEATER
2 EN
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Table of contents
Notes regarding the operating manual.................................2
Safety .....................................................................................3
Information about the device................................................5
Transport and storage...........................................................5
Assembly and installation.....................................................6
Operation .............................................................................10
Errors and faults..................................................................12
Maintenance ........................................................................13
Technical annex...................................................................14
Disposal ...............................................................................14
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of hot surface
This symbol indicates dangers to the life and health of
persons due to hot surface.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
IRD 1200
https://hub.trotec.com/?id=41386
IRD 1800
https://hub.trotec.com/?id=41387
IRD 2400
https://hub.trotec.com/?id=41388
IRD 3200
https://hub.trotec.com/?id=41389
EN 3
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
Warning
Children of less than 3years should be kept away
unless continuously supervised.
Children aged from 3years and less than 8years shall
only switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children aged from 3years and less than 8years shall
not plug in, regulate and clean the appliance or
perform user maintenance.
Warning
Do not use the device in small rooms if persons are
present who cannot leave the room independently and
who are not under constant supervision.
Do not use the device in potentially explosive rooms.
Do not use the device in aggressive atmosphere.
Let the device dry out after a wet clean. Do not operate it
when wet.
Do not use the device with wet or damp hands.
Do not expose the device to directly squirting water.
Never insert any objects or limbs into the device.
Do not cover or transport the device during operation.
This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
The electrical connection must correspond to the
specifications in chapter Technical data.
Insert the mains plug into a properly secured mains
socket.
Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
During the installation of the device observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
Do not use the device in immediate proximity to curtains.
Do not transport the device during operation.
Allow the device to cool down before transport and/ or
maintenance work.
The device must not be installed directly beneath a wall
socket.
The device must be set up in a way that the switches and
controllers cannot be touched by a person in a bathtub or
shower.
4 EN
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Intended use
Use the device IRD 1200/ IRD 1800/ IRD 2400/ IRD 3200 for
heating surfaces in roofed and non-roofed outdoor areas.
Intended use comprises:
heating surfaces
in storage facilities,
in construction areas,
in containers,
in the catering trade,
at trade fairs and events,
in outdoor areas (e.g. terraces).
Improper use
The device is not intended for industrial use.
Do not place any objects, e.g. clothing, on the device.
Do not use the device for heating in vehicles.
Do not use this device in the vicinity of fuel, solvents,
varnishes or other easily inflammable vapours or in rooms
where these substances are stored.
The device may not be used as a heating device for
babies / children or animals.
The device may not be installed inside a shower or directly
above a bathtub.
The device must not be used near swimming pools.
Do not use this device in the immediate vicinity of sinks,
bathtubs or other water containers.
Never immerse the device in water.
Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Any unauthorised changes, modifications or alterations to the
device are forbidden.
Personnel qualifications
People who use this device must:
be aware of the dangers that occur when working with
electric devices in damp areas.
have read and understood the operating manual, especially
the Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
Trotec.
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of hot surface
Some parts of this product can become very hot and
cause burns. Particular attention has to be given where
children and vulnerable people are present!
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
Improper installation or mounting entails a risk of fire.
Warning
Risk of injury due to infrared radiation!
Do not stay in the device's immediate vicinity for too
long. Do not look directly into the device for too long.
Observe the minimum distances.
Warning
In order to avoid overheating and fire hazards, the
device must not be covered!
Behaviour in the event of an emergency
1. Switch off the device.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
EN 5
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Information about the device
Device description
The infrared radiant heater (blacklight) IRD 1200 serves to
quickly generate heat without emitting light.
The device is based on the functional principle of heat
generation by infrared radiation. Persons or objects are heated
directly.
Via a stainless steel heating coil enclosed in aluminium, the
device emits most of its radiation energy in the long-wave
infrared spectrum. The device does not generate any dazzling
red light during operation. In addition, this type of heat
generation is also energy-saving. The full heating capacity is
only reached after approx.10min of operation. This is why the
device is classified as slow-acting with regard to its operating
principle.
The maximum effective range is approx.2.7metres. Wind and
draught, however, can reduce this effective range. For this
reason, it is recommended to use the device in outdoor areas
sheltered from the wind.
The 3heating levels can be selected using the remote control.
The device indicates operation by means of two coloured LEDs.
Using the timer function the device can be switched off
automatically with time delay.
suitable for interior spaces and outdoor use in areas
sheltered from the wind
IP55 type of protection – splash- and water-jet-proof
suitable for mounting on walls and ceilings
adjustable angle
no dust circulation (suitable for allergy sufferers)
Device depiction
1
2
5
3
TIMERP3
P2P1
4
No. Designation
1 Display with infrared receiver for remote control
2 On/off switch
3 Guide rail for device holder
4 Remote control
5 Aluminium cover
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
Switch the device off.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Do not use the power cable to drag the device.
Allow the device to cool down sufficiently.
6 EN
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Storage
When the device is not being used, observe the following
storage conditions:
dry and protected from frost and heat
in an upright position where it is protected from dust and
direct sunlight
with a cover to protect it from invasive dust, if necessary
Remove batteries from the remote control.
Assembly and installation
Scope of delivery
TIMERP3
P2P1
6
7
8
9
10
11
12
13
4
14
15
161718
1x Device (not pictured)
4x Mounting bracket(6)
2 x Device holder(7)
4 x Hexagon nut M8(8)
4 x Spring washer Ø 8.1 mm(9)
4 x Washer Ø 8.4 mm(10)
4 x Threaded steel anchor M8(11)
2 x Wing screw M6(12)
4 x Hexagon screw M6(13)
4 x Spring washer Ø 6.1 mm(14)
4 x Hexagon nut M6(15)
4 x Spring washer Ø 4.1mm(16)
4 x Hexagon nut M4(17)
4 x Phillips screw M4(18)
1 x Remote control(4)
1xManual (not pictured)
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
The device is suited for wall and ceiling mounting. Observe the
following requirement for installation inside a room:
Warning
Risk of fire due to improper installation!
There is a risk of fire if the required minimum
distances are not observed.
The device must be positioned at a distance of at least
220 cm from the floor and at least 100 cm from walls
and other objects such as curtains or sockets.
Mounting the wall/ceiling holder
Info
The mounting procedure is identical for all devices.
ü Use tools suitable for the intended task.
1. Connect one device holder and one mounting bracket each
using two medium hexagon screws(M6), hexagon
nuts(M6) and spring washers(Ø6.1mm).
2. Connect the second device holder to the second mounting
bracket.
EN 7
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
3. Push the two device holders into the guide rails one after
the other. Pay attention not to push the device holders
over the power cable when inserting them in the guide rail.
4. The brackets' position can be freely adjusted. The
recommended distances are provided in the table below:
Holder
distance
IRD 1200 IRD 1800 IRD 2400 IRD 3200
Minimum 400 mm 600 mm 800 mm 1100 mm
Maximum 930 mm 1195 mm 1460 mm 1815 mm
5. Tighten the two wing screws on the device to lock the
device holders.
Installation
When installing the device, observe the minimum distances
from walls and other objects as described in the Technical data
chapter.
Minimum distance of 220cm and maximum distance of
270cm from the floor.
Minimum distance of 100 cm to the front or from objects.
Minimum distance of 30 cm from the ceiling in case of
wall mounting or, for technical reasons, 19.5cm in case of
ceiling mounting.
Minimum distance of 20 cm to the sides.
Do not install the device directly in front of a wall socket.
The socket should be located next to the device. If the
device is installed on a pitched ceiling, the socket should
be located at the bottom side of the device.
Do not install the device directly behind a door.
Never install the device in a way that it radiates directly
onto walls or other objects.
Only install the device in a horizontal position.
8 EN
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Please note that the minimum distance to the front also
applies to objects mounted on the ceiling, e.g. fans, lamps
or sprinkler systems.
220 cm
30 cm
20 cm
20 cm
100 cm
Info
Please note that in case of ceiling mounting the
distance from the ceiling is 19.5cm due to the length
of the mounting brackets.
For wall mounting, the minimum distance of 30cm
from the ceiling applies.
The following is required for installation:
a pencil for marking the drill holes
a suitable drill
wall plugs appropriate for the structure of the wall and for
the device weight
a screwdriver
a spirit level
Note
Always install the device with the help of other
persons.
1. Measure the distance between the holders on the device
and use this value for the distance between the drill holes.
2. Mark the drill holes on the wall / ceiling. Please note the
mounting brackets must be fastened vertically.
3. Drill the holes into the wall / ceiling at the marked
positions.
4. Insert suitable wall plugs into the drill holes.
5. Screw the mounting brackets to the wall / ceiling.
6. Check the mounting brackets for tight fit.
EN 9
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
7. The device can be installed at an inclination angle of 0°,
15°, 30° or 45 °.
Please note that the inclination angle must be 15°, 30° or
45° for wall mounting and 0°, 15° or 30° for ceiling
mounting.
30°
45°
15°
8. Connect the mounting brackets on the device to those on
the wall/ ceiling at the desired inclination angle. For each
side, use two Phillips screws, two small hexagon nuts(M4)
and spring washers(Ø4.1mm).
9. Make sure that the device is attached securely.
Effective range
The device heats objects and persons inside a certain effective
range. This effective range differs depending on whether the
device is installed indoors or outdoors. In outdoor areas, the
effective range is influenced by the weather and may be
reduced.
a
b
c
d
a Height b Depth
c Width d Effective range
IRD 1200 IRD 1800 IRD 2400 IRD 3200
a 2.2 m 2.2 m 2.2 m 2.2 m
b 2.1 m 2.1 m 2.1 m 2.1 m
c (indoors) 1.9 m 2.4 m 2.95 m 3.55 m
d (indoors) approx.
4.0 m
2
approx.
5.1 m
2
approx.
6.2 m
2
approx.
7.5 m
2
c (outdoors) 1.55 m 1.95 m 2.35 m 2.75 m
d (outdoors) approx.
3.3 m
2
approx.
4.1 m
2
approx.
5.0 m
2
approx.
5.8 m
2
10 EN
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Start-up
Info
Odours might arise upon initial start-up or after a
longer period of non-use.
Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
Make sure that extension cables are completely unrolled.
Make sure that there are no curtains or similar objects in
the immediate vicinity.
Prior to initial start-up, insert the batteries in the remote control.
Connecting the power cable
Insert the mains plug into a properly secured mains
socket.
Make sure that the power cable is guided along the back
of the device. Never guide the power cable along the front
of the device!
Operation
Info
The device will only emit heat if the settings are made
via the remote control.
Display
20
21
19
No. Designation Meaning
19 Operating light Flashes red when the device has been
switched on via the on/off switch.
Is permanently illuminated in red when
the device has been switched on via the
remote control.
20 Timer LED Is permanently illuminated in green
when the timer is active.
21 Segment display Heating level indication:
P0 = device in standby mode
P1 = level 1
P2 = level 2
P3 = level 3
Indication of the number of hours during
timer programming
Info
An acoustic signal is emitted each time a setting is
activated.
Info
If you switch off the device via the remote control, the
device will be set to standby mode. If standby
operation is not required, you can switch the device off
via the on/off switch(2).
EN 11
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Remote control
The device settings can only be made using the remote control
included in the scope of delivery.
Therefore, keep the remote control in a safe place, otherwise
the device can no longer be operated. Should you still be unable
to find the remote control, you can reorder a new one from
Trotec.
TIMERP3
P2P1
22
23
27
26
24
25
No. Designation Meaning
22 Transmitter Sends signals to the device.
23 Power button Switching the device on and off
24 P2 button Selecting heating capacity level2
25 TIMER button Timer function
Automatic switch-off in increments of
1hour up to 24hours
26 P3 button Selecting heating capacity level3
27 P1 button Selecting heating capacity level1
The heating capacity in the individual heating levels is 33%
(level1), 66% (level2) and 100% (level3):
Heating
capacity
IRD 1200 IRD 1800 IRD 2400 IRD 3200
P1 = level1 400 W 600 W 800 W 1070 W
P2 = level2 800 W 1200 W 1600 W 2140 W
P3 = level3 1200 W 1800 W 2400 W 3200 W
Info
If you switch off the device via the remote control, the
device will be set to standby mode. If standby
operation is not required, you can switch the device off
via the on/off switch(2).
Switching the device on
Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.
1. Set the on/off switch(2) on the device to I.
ð The operating light(19) flashes.
ð The device is now in standby mode.
2. Press the Power button(23) on the remote control.
ð The segment display(21) indicates P0.
ð The operating light(19) is illuminated.
ð The device is switched on, but does not heat yet.
3. Press the corresponding button(24, 26, 27) on the remote
control to set the desired heating level.
ð The device heats.
ð The selected heating level flashes in the segment
display(21).
ð The operating light(19) is permanently illuminated
during operation.
Setting the timer
The timer allows you to program an automatic switch-off time in
increments of 1hour up to 24hours at any heating level.
You can change the heating level during timer programming.
The timer programming remains activated.
ü The device is switched on.
ü The heating level is set.
1. Press the TIMER button(25) several times to set the
desired number of hours until automatic switch-off.
ð The timer LED(20) is illuminated.
ð The segment display(21) indicates the number of hours
until automatic switch-off.
ð The timer has been programmed and the device will
switch off after the predefined time.
2. In order to delete the setting, select 00 hours using the
TIMER button(25).
ð The segment display(21) indicates the number of hours
00.
ð The timer has been deleted.
12 EN
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Info
If you switch off the device via the remote control, the
device will be set to standby mode. If standby
operation is not required, you can switch the device off
via the on/off switch(2).
Switch off the device by pressing the Power button(23) on
the remote control. The operating light flashes. Then set
the on/off switch(2) on the device to 0.
Allow the device to cool down completely.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Errors and faults
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Noise generation (clicking) during switch-on or cooling:
This is not a fault. The device's metal parts expand when
heated and contract when cooling, and thus generate
noise. This is a perfectly normal process. No measures are
required.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damages.
Check the on-site fusing.
Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device does not emit heat:
The heating rod might be defective. Have a defective
heating rod replaced by a specialist electrical company.
Check the heating level on the segment display. If P0 is
displayed, the device is running in standby mode.
Switch the device on by selecting another heating level
between P1 and P3.
Check the on/off switch. If the on/off switch is set to the0
position, the device is switched off.
Switch the device on.
Check the operating light. If the operating light flashes red,
the device is running in standby mode.
Switch on the device by selecting a heating level via the
remote control.
Contact a specialist electrical company.
The heat output is low:
Strong wind or cold temperatures in outdoor areas can
impair the device's heat output.
Check whether the device is installed in the correct
position. The device may be installed too high or the
inclination angle may be incorrect.
The device is undersized for the area to be heated.
The heating rod might be defective. Have a defective
heating rod replaced by a specialist electrical company.
EN 13
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
RCD or another fuse trips:
Check the fuse. Switch off any other devices to reduce the
load on the line.
Contact a specialist electrical company.
The device slightly vibrates during switch-on and then
stops vibrating:
Slight vibrations during switch-on are a normal process.
No measures are required.
The device does not respond to the infrared remote control:
Check whether the distance between remote control and
device is too large and reduce it if necessary.
Make sure there are no obstacles, such as furniture or
walls, between the device and the remote control. Ensure
visual contact between device and remote control.
Check the charging status of the batteries and change
them if required.
If the batteries have only just been changed, check them
for correct polarity.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch the device off.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down completely.
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
Cleaning the device
Clean the device with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Wipe the housing dry after cleaning.
14 EN
infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Technical annex
Technical data
Parameter Value
Model IRD 1200 IRD 1800 IRD 2400 IRD 3200
Heating capacity (level1 /2 /3) 400/ 800/
1200W
600/ 1200/
1800W
800/ 1600/
2400W
1070/ 2140/
3200W
Max. heating capacity 1.2 kW 1.8 kW 2.4 kW 3.2 kW
Nominal current consumption 5.2 A 7.8 A 10.4 A 13.9 A
Power supply 1/N/PE ~ 220–
240V / 50–60Hz
1/N/PE ~ 220–
240V / 50–60Hz
1/N/PE ~ 220–
240V / 50–60Hz
1/N/PE ~ 220–
240V / 50–60Hz
Plug type CEE7/4 CEE 7/4 CEE 7/4 CEE 7/4
Protection class IP55 IP55 IP55 IP55
Dimensions (depth x width x height) 55 x 930x 200mm 55 x 1195x
200mm
55 x 1460x
200mm
55 x 1815x
200mm
Minimum distance to walls and other objects:
top (wall mounting):
top (ceiling mounting):
bottom:
sides:
front:
30 cm
19.5 cm
220 cm
20 cm
100 cm
30 cm
19.5 cm
220 cm
20 cm
100 cm
30 cm
19.5 cm
220 cm
20 cm
100 cm
30 cm
19.5 cm
220 cm
20 cm
100 cm
Weight 8 kg 9.5 kg 11.5 kg 13.5 kg
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Trotec IRD1800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Trotec IRD1800 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Trotec IRD1800

Trotec IRD1800 Gebruiksaanwijzing - Nederlands - 16 pagina's

Trotec IRD1800 Gebruiksaanwijzing - Deutsch - 15 pagina's

Trotec IRD1800 Gebruiksaanwijzing - Français - 14 pagina's

Trotec IRD1800 Gebruiksaanwijzing - Italiano - 16 pagina's

Trotec IRD1800 Gebruiksaanwijzing - Espanõl - 16 pagina's

Trotec IRD1800 Gebruiksaanwijzing - Polski - 16 pagina's

Trotec IRD1800 Gebruiksaanwijzing - Türkiye - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info