4
GB
General Safety
WARNING: When using electric power tools,
fire, electric shock and personal injury including the following safety information.
attempting to operate this product and save these instructions for future use.
WARNING: This appliance is not intended for use by persons (including children) with reduced,
capabilities or lack of experience or knowledge unless they have been given super
of the appliance by a person responsible for their safety
with the appliance.
CAUTION: Use the power tool,
the working conditions and the work to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
The term “power tool”
(cordless) power tool.
1 - Cluttered areas and benches invite injuries
2 - Consider work area environment
- Do not expose tools to rain
- Do not use tools in damp or wet locations
- Keep work area well lit
- Do not use tools in the presence of flammable liquids or gases
3 - Guard against electric shock - Avoid body contact with earthed or grounded surfaces (e.g.
ranges, refrigerators)
4 - Keep other persons away - Do not let persons,
the extension cord and keep them away from the work area
5 - Store idle tools - When not in use,
6 - Do not force the tool - It will perform the job better and safer at the rate for which it was intended
7 - Use the right tool - Do not force small tools to do the job of a heavy duty tool
- Do not use tools for purposes not intended; for example do not use circular saws to cut tree limbs or logs
8 - Dress appropriately
- Do not wear loose clothing or jewellery
- Suitable safety footwear is recommended when working outdoors.
- W
9 -
-Use safety glasses
-Use face or dust mask if working operations create dust
WARNING: Not using protective equipment or appropriate clothing can cause personal injury or increase the severity
of an injury.
10 - Connect dust extraction equipment - I
equipment, ensure these are connected and properly used
11 - Do not abuse the power cable - Never yank the power cable to disconnect it from the socket. Keep the power
cable away from heat, oil and sharp edges.
shock
12 - Secure work -
13 - Do not overreach - Keep proper footing and balance at all times
14 - Maintain tools with care
- Keep cutting tools sharp and clean makes the tool easier to control and less likely to bind or lock in the
workpiece
- Follow instruction for lubricating and changing accessories
- Inspect tool power cables periodically and if damaged have them repaired by an authorized ser
- Inspect extension cables periodically and replace if damaged
- Keep handles dry,
- Set the tool up in a stable position
WARNING: Many accidents are caused by poorly maintained power tools.
15 - Disconnect tools - When not in use,
cutters, disconnect tools from the power supply
WARNING: The use of accessories or attachments not recommended by the manufacturer may result in a risk of injury
to persons.
16 - Remove adjusting keys and wrenches - Form the habit of checking to see that keys and adjusting wrenches
are removed from the tool before switching it on
17 - Avoid unintentional starting - Ensure switch is in
inserting a battery pack, or when picking up or carrying the tool
WARNING: Unintended starting of a tool can cause major injuries.
18 - Use outdoor extension leads - When the tool is used outdoors,
use and so marked. Use of an extension cable suitable for outdoor use reduces the risk of electric shock
19 - Stay alert
- W
- Do not use a power tool while you are under the influence of drugs, alcohol or medication
WARNING: A moment of inattention while operating power tools may result in serious personal injury.
20 - Check damaged parts
- Before further use of tool, it should be carefully checked to determine that it will operate properly and perform
its intended function
- Check for alignment of moving parts, binding of moving parts,
conditions that may affect its operation
- A guard or other part that is damaged should be properly repaired or replaced by an authorized service centre
unless otherwise indicated in this instruction manual
- Have defective switches replaced by an authorized service centre
WARNING: Do not use the tool if the on/off switch does not turn it on and off.
tool is used.
21 - Have your tool repaired by a qualified person - This electric tool complies with the relevant safety rules.
Repairs should only be carried out by qualified persons, otherwise this may result in considerable danger to the
user
WARNING: When servicing use only identical replacement parts.
WARNING: If the power cable is damaged it must be replaced by the manufacturer or an authorised service centre.
22 - Power tool mains plugs must match the mains socket - Never modify the plug in any way
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching sockets will reduce risk of
electric shock
23 - If operating a power tool outside use a residual current device (RCD) - Use of an RCD reduces the risk of
electric shock
NOTE: The term
or “earth leakage circuit breaker (ELCB)”.
WARNING: When used in
Current Device (RCD) with a rated residual current of 30mA or less.
WARNING: Before connecting a tool to a power source (mains switch power point receptacle,
the voltage supply is the same as that specified on the nameplate of the tool.
than that specified for the tool can result in serious injury to the user
the tool. Using a power source with a voltage less than the nameplate rating is harmful to the motor
T
WARNING: AL
defenders, a suitable dust mask and suitable gloves when using a saw table.Ensure all people in the vicinity of
the work area use adequate protection. Keep bystanders a safe distance away
WARNING: AL
extraction system when sawing wood. Certain types of wood are toxic or may cause allergic reactions in people
and animals, especially when exposed to very fine dust.
vacuum dust extraction.
WARNING: The rated speed of the saw blade must be at least equal to the maximum speed marked on the
power tool. Accessories running faster than their rated speed could break and fly apart.
a) ONLONL
saw blades, ensuring that the riving knife is not thicker than the blade kerf,
b) ENSURE your work area is safe and sufficiently lightened,
potential dangers.
c) NEVER attempt to cut metals or drywall products containing masonrIt is exclusively
designed for use with wood and wood-like products.
d) DO NOThe compatible circular saws and the table setup
are not suitable for this kind of cutting.
e) ALRemove sawdust frequently and c
saw,
f) NEVER attempt to remo
spinning. AL
come to a standstill.
g) NEVER leave the saw running unattended.
come to a complete stop.
h) CAREFULLand follow these recommendations when
using a saw table.
i) ALThe feed direction is indicated
by the arrow moulded into the table surface.
j) ALEnsure the fence is parallel to the blade,
angled towards the blade, and securely lock the fence at both ends.
k) ALNEVER use the rip fence during the
same operation as the mitre gauge.
l) NEVER remove the blade guard or riving knife. Riving knives are also known under the term
m) AL
blade. The push stick must
contact with the blade. Use a featherboard and push blocks for non-through cuts.
saw,
n) NEVER perform any free-hand operations,AL
either the rip fence or a mitre fence to position and guide the work.
o) NEVER reach behind, over or within 75mm (3”) of the blade,
p) ALNEVER use the rip fence as a cut-off
gauge when cross cutting.
q) NEVER attempt to free a stalled saw blade,AL
machine from the power supply
r) AL
necessary,Use roller supports or saw horses wherever possible.
s) NEVER let go of the workpiece before it is pushed all the way past the sausing a push stick where
necessary.
t) AVOID irregularly shaped workpieces that do not have a straight edge to guide along the rip fence.
u) DO NODO NOT use table saws to cut logs or firewood.
v) ALW where a sudden slip could cause your hand or other
parts of your body to come into contact with the blade.
w) INSPECT the throat plate before use. Replace throat plates that are damaged or worn.
x) ONLThe use of incompatible
accessories may inherently be dangerous and lead to severe injury or property damage.
instructions and safe usage procedures, provided with the accessory
y) ALWThis avoids accidental
starting upon reconnecting to the power supply
Kickback Prevention
Note: Kickback occurs when the blade stalls rapidly
the workpiece is driven back towards the operator
serious injury.
WARNING:
precautions are taken, kickback forces can be controlled by the operator
a) ALNEVER remove the riving
knife, to prevent the kerf from c
b) NEVER attempt to cut with a dull or warped blade.AL
cut.
c) ALIf the fence tilts inward towards the blade,
may come into contact with the back edge of the blade, and may be thrown back towards the user uncontrollably
as a result.
d) NEVER use the rip fence and mitre gauge simultaneouslyThis can lead to serious kickback and severe injury
e) Use CAUTION when cutting large sheets.Ensure larger stock is properly supported by adequate in-feed and
out-feed supports.
f) DO NOT cut round stock or workpieces that cannot lay flat on the table.Avoid cutting twisted, distorted or
knotty wood.
g) DO NOWet sawdust can accumulate on
the blade, further increasing the likelihood of kickback.
h) AL
forces.
i) Stay out of blade path and position your body to either side of the blade, but not in line with the blade.
255671_Z1MANPRO1.indd 4 23/11/2016 10:38
