665086
6
Verklein
Vergroot
Pagina terug
1/82
Pagina verder
6
GB
g) Make sure there are no nails or other foreign objects in the area of the workpiece to
be sanded.
h) Never use this sander for wet sanding. Failure to comply may result in electrical shock,
causing serious injury or worse.
i) Use only identical replacement parts when servicing this spindle sander.
j) Make sure the spindle has come to a complete stop before touching the workpiece.
k) Take precautions when sanding painted surfaces. Sanding lead-based paint is NOT
RECOMMENDED. The contaminated dust is too difficult to control, and could cause lead
poisoning.
When sanding paint:
a) Protect your lungs. Wear a dust mask or respirator.
b) Do not allow children or pregnant women in the work area until the paint sanding
job is finished and the clean-up is completed
c) Do not eat, drink, or smoke in an area where painted surfaces are being sanded
d) Use a dust collection system when possible. Seal the work area with plastic. Do not
track paint dust outside of the work area
e) Thoroughly clean the area when the paint sanding project is completed
Product Familiarisation
1. On-Board Table Insert Storage
2. On/Off Switch
3. Motor Housing
4. Table Top
5. Spindle
6. Spindle Lock Nut
7. Lower Spindle Washer
8. On-Board Spindle Storage
9. Upper Spindle Washers (x3)
10. Table Insert (x 6)
11. Sanding Sleeve (x 6)
12. Rubber Drum (x 5)
13. Dust Extraction Port
14. Wrench
Intended Use
Bench-mounted sanding machine with a rotating and height oscillating sanding drum.
For sanding curved and straight surfaces on intricate as well as larger workpieces.
Unpacking Your Tool
Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Bench mounting
If the spindle sander is to be used in a permanent position, it is recommended that you secure
it to a rigid work surface.
Use the holes in the base of the spindle sander (image A) as a template to mark and drill
four holes in your intended mounting surface (ie workbench). Secure the spindle sander
into position using large bolts, washers and nuts (not supplied)
If the spindle sander is intended to be more portable, fix a board to the base which can be
easily clamped and removed from various mounting surfaces
f using bolts make sure they are long enough to penetrate the workbench or board
sufficiently for a secure fix
Note: Use nylon insert lock nuts or spring washers in the fixings to prevent vibration from
loosening the fixings.
Note: Never use bolts that require force to push through the Bench Mounting Holes as these
may crack the plastic body as will over-tightening the fixings.
Dust extraction
It is recommended that the spindle sander is used with a dust extraction system for a cleaner
and safer work environment.
1. Attach the hose from the dust extraction system to the Dust Extraction Port (13) and
ensure it is secure
2. For greatest efficiency, activate the dust extraction system before turning on the spindle
sander
Selecting a table insert
Failure to use the correct table insert with its matching sanding sleeve could result in pinched
fingers or the workpiece being pulled down between the table insert and the sanding sleeve.
The sanding sleeve should fit snugly into the central cutout of the table insert (Images B
and C).
Use the following chart to help determine the correct table insert and upper spindle washer to
use with each sanding sleeve.
Sanding
Sleeve Dia
Table
Insert Size
Upper Spindle
Washer Size
13 mm / 1/2" 13 mm / 1/2" Small
19 mm / 3/4" 19 mm / 3/4" Medium
26 mm / 1" 26 mm / 1" Medium
38 mm / 1 1/2" 38 mm / 1 1/2" Large
51 mm / 2" 51 mm / 2" Large
76 mm / 3" 76 mm / 3" Large
Selecting the right grade of sanding sleeve
Sanding sleeves are available in a variety of different grades: coarse (80 grit), medium
(150 grit) and fine (240 grit)
Use a coarse grit to sand down rough finishes, medium grit to smooth the work, and fine
grit to finish off
Always use good quality sanding sleeve to maximise the quality of the finished task
It is advisable to do a trial run on a scrap piece of material to determine the optimum
grades of sanding sleeve for a particular job. If there are still marks on your work after
sanding, try either going back to a coarser grade and sanding the marks out before
recommencing with the original choice of grit, or try using a new piece of sanding sleeve
to eliminate the unwanted marks before going on to a finer grit and finishing the job
Fitting a sanding sleeve
Note: All of the Sanding Sleeves (11), except the smallest 13mm (1/2”) Sanding Sleeve fit over
a matching Rubber Drum (12).
Note: Ensure there is no contact between the Sanding Sleeve and the Table Insert before
turning the machine on.
1. Fit the Lower Spindle Washer (7) over the Spindle (5) with the grooves facing upwards
(Image D)
2. Select the correct Sanding Sleeve for the intended job. Select the corresponding Rubber
Drum, (except when using the 13mm sanding sleeve)
3. Select the appropriate Table Insert (10) in accordance with the table in ‘Selecting a
table insert’
4. Fit the Table Insert over the Spindle and onto the Lower Spindle Washer (see Image B).
Ensure the Table Insert is flush with the table
5. Fit the Rubber Drum over the Spindle (Images E and F)
6. Slide the Sanding Sleeve over the Rubber Drum
7. Fit the Upper Spindle Washer (9) over the Spindle
Use the large washer with the 75mm (3”), 51mm (2”), and 38mm (1 1/2”) Rubber Drums
Use the medium washer with the 26mm (1”) and 19mm (3/4”) Rubber Drums
Use the small washer with the 13mm (1/2”) Sanding Sleeve
8. Fit the Spindle Lock Nut (6) on the Spindle (Images G and H). Tighten the nut just enough
to expand the Rubber Drum against the Sanding Sleeve. Do not over-tighten
When the sanding sleeve is completely worn it is possible to turn it upside down and
maximise its service life by using the remaining grit
Note: If the sleeve rotates on the drum when switched on, the Spindle Lock Nut has not been
sufficiently tightened to compress the drum and therefore grip the sleeve.
IMPORTANT: Do not use a sanding sleeve that is too worn. This can lead to excessive heat
build-up and damage the rubber drum. Damaged rubber drums due to worn sanding sleeves
will not be covered under warranty.
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection,
as well as suitable gloves, when working with this tool.
WARNING: ENSURE gloves and clothes worn do not have loose threads that could get
caught by the rotating spindle and drag your hand or head into the rotating spindle causing
severe injury. It is recommended to wear gloves that are not fabric based.
Switching on and off
The On/Off Switch (2) is located on the front of the spindle sander (Image A)
To turn the spindle sander ON: Press the green button marked (-)
To turn the spindle sander OFF: Press the red button marked (O)
516693_Z1MANPRO1.indd 6 30/08/2016 16:28
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Triton TSPS450 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Triton TSPS450 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks als bijlage per email.

De handleiding is 7,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info