665059
7
Verklein
Vergroot
Pagina terug
1/90
Pagina verder
7
GB
7. Disconnect the Battery Charger from the power supply and store in a clean, dry
environment out of the reach of children
Normal battery charging time is approximately 1 hour for a recently fully discharged battery
at normal temperature. Charging times will vary outside these conditions
The Battery does not need to be fully discharged before recharging but a fully charged
Battery must not be charged
You can interrupt charging at any point to use the Battery. Under normal conditions the
Battery Charger charges at a higher rate but reduces the charging rate as the Battery
becomes fully charged. An 80% charge is achieved after 1/2hr of charging
3.0Ah High Capacity Battery (optional accessory)
A high capacity battery is available that provides double the capacity. It also allows the tool
to stand vertically which may be advantageous for some uses. Please note the full charging
time will be approximately 2 hours for the high capacity battery
Battery Charging Table
Red LED Green LED
Battery Charger (11) plugged in OFF Flashing
Battery Charger evaluating Battery (5) OFF Flashing
Fast charging ON OFF
Highly discharged Battery slow charging Flashing OFF
Abnormal Battery temperature charging Flashing OFF
Fully charged OFF ON
Battery or Battery Charger fault Flashing Flashing
Abnormal temperature ON ON
Note: If the lights on the Battery Charger fail to illuminate according to the chart above or
indicate a fault condition:
Check the Battery is firmly seated in the Battery Charger
Check all connections and that mains power is switched on
Initial charge
The initial charge will vary depending on the existing charge in the Battery. Allow the
Battery to reach full charge as indicated on the Battery Charger
After discharging, recharge the Battery completely, as indicated by the LED on the Battery
Charger, for the next 4 to 5 uses. This will ensure that the Battery is performing to its
highest capacity
Subsequent full charges will take approximately 1 hour. However, the Battery can be
recharged when the Battery is only partially discharged
Re-charging the battery
After use, a li-ion battery must be allowed to cool down before charging
If a hot battery is inserted into the charger both LEDs will illuminate. The charger will begin
to charge when the battery has cooled sufficiently (this may take several minutes)
Installing the battery
The Battery should fit easily into the Battery Charger. If the Battery is difficult to fit, check
the condition of the Battery and contacts
Battery - length of service
The length of service from each charging cycle will depend on the type of workload. The
Battery Charger and Battery for this tool have been designed to provide a long trouble-free
working life. The Battery Charger intelligently monitors the condition of the Battery and
selects the ideal charging rate for the condition of the Battery. It protects the Battery from
over-charging or charging at too high a rate. However, like all batteries, performance will
be reduced over time
To maximise battery life:
Store and charge the Battery in a cool area. Temperatures above or below normal room
temperature will reduce battery life
Never store li-ion batteries in a discharged condition. Recharge them immediately after they
are discharged. For storing long term, store fully charged
All batteries gradually lose their charge, even li-ion batteries, but the discharge rate is very
low. If the tool is stored for long periods of time without use, recharge the battery every
three to four months and disconnect the battery from the power tool before it is stored. This
practice will prevent the li-ion battery being damaged when stored
Fitting accessories
Fitting a blade or scraper
WARNING: Always wear suitable gloves when handling sharp blades>
1. Remove the Battery if fitted
2. Use the supplied Blade Hex Key (15) to loosen and remove the Blade Bolt (14) and Blade
Washer (13), turning the Blade Bolt anti-clockwise as you face the bolt head as shown in
image A
3. Position the blade or scraper on to the Blade Mounting (9) so that the mounting holes in the
blade engage with the pins on the Blade Mounting. See image B
4. The blade or scraper can be positioned at an angle not directly in line with the tool if
required, so long as the blade or scraper mounting holes are engaged with the pins on the
Blade Mounting
5. Re-fit the Blade Bolt and Blade Washer as shown in image B carefully ensuring the blade
or scraper correctly sits in the Blade Mounting pins as the bolt is tightened. The blade or
scraper and Blade Mounting can be damaged if the pins are not inserted into the Blade
Mounting holes
6. Check that the blade or scraper is securely fitted and the bolt is tight before refitting the
Battery
Note: Blades or scrapers that are cranked or bent must be mounted on the tool so that the end
of the blade is away from the tool as shown in image B
Fitting the sanding pad and paper
1. Remove the Battery if fitted
2. Use the supplied Blade Hex Key (15) to loosen and remove the Blade Bolt (14) and Blade
Washer (13) turning the Blade Bolt anti-clockwise as you face the bolt head as shown in
image A
3. Mount the sanding pad (17) onto the Blade Mounting (9) so that the mounting holes in the
sanding pad engage with the pins on the Blade Mounting. See image C
4. The sanding pad can be positioned at an angle if required but normally a point of the
triangle base is directly in line with the body of the tool
5. Re-fit the Blade Bolt and Blade Washer as shown in image C carefully ensuring the sanding
pad correctly sits in the Blade Mounting pins as you tighten the bolt. The sanding pad and
Blade Mounting can be damaged if the pins are not inserted into the Blade Mounting holes
6. Before using the tool, Check that the sanding pad is securely fitted and the bolt is tight
7. Select the required sanding sheet for your intended task. Each sheet is marked with its grit
level on the reverse side. A lower grit number means that the sanding sheet has a coarser
grit and so is more abrasive
8. The sanding pad and sanding sheets use a hook and loop system for attachment. To mount
the sheet carefully line up one corner of the sheet with a corner of the sanding pad and
gradually allow the rest of the sheet to contact the pad checking alignment as you do so
until the sheet is fitted correctly. See image D
9. Refit battery
Operation
Built-In Safety Features
IMPORTANT: The oscillating multi-tool has 3 important safety features which will prevent the
tool from operating under certain circumstances.
1. Cell Protection: If the battery charge is very low the tool will stop operating to prevent the
battery being fully discharged which will damage li-ion batteries
2. Over Heat Protection: If the battery or tool temperature is too high the tool will switch off to
prevent damage to the battery pack and tool
3. Over Current Protection: If excessive current is being drawn from the battery then the tool
will switch off to prevent damage to the battery pack and tool
It is recommended to swap batteries before the current battery is fully discharged to prevent
the tool from powering down in use. Allow the tool to cool between uses to prevent it getting
too hot and do not apply force when operating the tool but let the blade or sanding base do the
work. This should reduce the possibility of the tool powering down as you operate it.
Note: The tool may take up to 30 minutes to reset before it operates again if over-heat
protection has operated and up to a minute if over current protection has operated.
Switching on and off
Note: Gloves should be worn when operating this tool. Anti-vibration gloves are recommended
to protect users from the vibration level of the oscillating mechanism.
1. Hold the tool firmly as shown in Fig. E with the thumb over the On/Off Switch (1) as shown
in image E
2. Slide the On/Off Switch forward to switch on the tool
3. Adjust the speed using the Variable Speed Control (3). It is a fully variable control but six
speed settings are printed on the wheel for the operator’s reference
4. Operate the tool as required
WARNING: Do not operate the tool at maximum speed for extended periods.
Notes:
Allow the tool to reach the required speed before making contact with the workpiece
Always remove the tool from the workpiece when changing speed
After use slide the On/Off Switch back to turn off the tool
It is good practice to set the Variable Speed Control to the minimum level after use
A high speed setting is required for most cutting and sanding operations
A low speed setting may be required for polishing and careful detail sanding with a high
grit sanding sheet
WARNING: Motor Vents (2) allow heat generated from the motor to escape the body of
the tool and must not become blocked. Dust, wood chippings and swarf can block the Motor
Vents and cause the tool to shut down when the over-temperature protection operates. Swarf,
created when cutting metal, can also cause permanent damage if it enters the tool. Do not
103691_Z1MANPRO.indd 7 31/08/2016 11:16
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Triton T12OT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Triton T12OT in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks als bijlage per email.

De handleiding is 7,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info