Handleiding Triton SJA200 (pagina 7 van 62) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks)

665092

Verklein

Vergroot

Pagina terug

1/62

Pagina verder

Product Familiarisation

1. Fixed Jaw Urethane Face

2. Moving Jaw Urethane Faces (2pce)

3. Moving Jaw Locking Tab

4. Body

5. Rear Leg Locking Knob

6. Rear Leg

7. Foot Plates

8. Foot Pedal

9. Front Legs

10. Foot Pedal Locking Latch

11. Front Leg Locking Knobs

12. Extension Tray Mounting Holes

13. Lock / Release Switch

14. Fixed Jaw

15. Moving Jaw

Intended Use

The SuperJaws Portable Clamping System is a portable work holder which

clamps a variety of workpieces for a multitude of different applications.

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise

yourself with all its features and functions

• Ensure that all parts of the tool are present and in good condition. If any parts are

missing or damaged, have such parts replaced before attempting to use this tool

Before Use

Setting up

1. With SuperJaws placed upside down on the ground, loosen the Rear Leg Locking

Knob (5) and slide the Rear Leg (6) from its storage position (Image B)

• Pivot the Rear Leg just clear of the front face (Image A)

• Slide it all the way forward then lift and slide it fully into its

housing at the rear, then tighten the knob (Image C)

DO NOT extend the rear leg beyond the marked line (Fig. I)

2. Raise the Foot Pedal (8) until it ‘clicks’ into position (Image D)

3. Pivot the Front Legs (9) out as far as they will go (Image E), then turn the

Front Leg Locking Knobs (11) clockwise; until the rounded section of

the knob tightens onto the leg housing, as shown (Image F & G)

• Several turns may be necessary on initial set-up, until the clamps tighten into

place. A half turn is all that is required to release the legs when folding

4. Turn SuperJaws upright and recheck all legs are locked ﬁrmly in position (Image H)

5. Rotate the Moving Jaw Locking Tab (3) to the horizontal

position (Image I). SuperJaws is now ready for use

Folding

Folding is the reverse procedure of the steps described above. Ensure that:

• The Lock / Release Switch (13) is in the ‘unlock’ position (Image J)

• The Foot Pedal Locking Latch (10) is used to release and fold the Foot Pedal (8) (Image K)

• The Moving Jaw Locking Tab (3) is in the ‘vertical’ position

to prevent the jaw from sliding out (Image L)

• The Rear Leg (6) is engaged fully into its housing, and the Rear

Leg Locking Knob (5) is tightened ﬁrmly (Image M)

• When in its folded position, the Rear Leg becomes a carrying

handle, for easy transportation (Image N)

Operation

Clamping

1. Check that the Moving Jaw Locking Tab (3) is set to the ‘horizontal’ position (Image O),

and push the Moving Jaw (15) back until your workpiece ﬁts between the jaws (Image P)

2. Place the workpiece against the Fixed Jaw (14) and slide the moving

jaw forward until it touches the workpiece (Image Q)

Note: The jaw can also be advanced forward by pressing the Foot Pedal (8) repeatedly.

3. Slide the Lock / Release Switch (13) down to the ‘lock’ position (Image R)

Note: If preferred the switch can be locked after the work is clamped.

4. Apply downward pressure on the Foot Pedal (8) until sufﬁcient

clamping force has been applied (Image S)

Note: For extra force you may stand on the Foot Pedal (maximum

100kg), but do not jump on it, as you could damage the unit.

Releasing

1. Slide the Lock / Release Switch (13) up to the ‘release’ position (Image T)

2. Push on the Foot Pedal (8) then allow it to return up and release the workpiece (Image U)

Note: Ensure you are supporting the workpiece to prevent

it from falling once the jaw is released.

Note: If you have clamped the object very tightly, you may need to

exert more pressure on the Foot Pedal before it will release.

3. Slide the Moving Jaw (15) back, and remove your workpiece (Image V)

Clamping on one side of the jaw

• Some large or awkward workpieces can only be clamped on one side of the jaws (Image W)

Note: Always ﬁt a spacer (the same thickness as your workpiece) to the

other side of the jaws, to prevent the Moving Jaw (15) from skewing.

Clamping large objects (460mm to 956mm)

• The Moving Jaw (15) can be reversed to accommodate

workpieces measuring between 460mm and 956mm:

1. Set the Lock / Release Switch (13) to the ‘release’ position, and

ensure that the Foot Pedal (8) is released (Image X)

2. Check the Moving Jaw Locking Tab (3) is in the horizontal position (Image Y)

3. Slide the Moving Jaw fully from its tracks (Image Z)

4. Rotate the Moving Jaw by 180°, and re-insert it into the tracks (Images AA & AB)

Notes:

• When clamping objects with the Moving Jaw (15) reversed, ensure the workpiece

sits down onto, and is parallel to, the sliding jaw. Avoid clamping workpieces

at the top of the jaws (with a gap between the workpiece and the base of

the Moving Jaw) as excessive pedal pressure could damage the unit

• When clamping large or heavy materials, provide outboard support (such as a

MSA200 Triton Multi-Stand 330090) to prevent SuperJaws from tipping over

Using as an anvil

• The ﬁxed jaw is sufﬁciently robust to be used as an anvil

for strip metal work (Images AC & AD)

• Do not use the Moving Jaw as an anvil, as this could cause damage

• For thicker materials we recommend the use of the optional

SJA470 Engineers’ Jaws (product code 330120)

Using as a press

• When the Lock / Release Switch (13) is in the ‘release’ position

(Image X), SuperJaws can be used as a press (Image AE)

• With each full stroke of the Foot Pedal (8), the Moving Jaw

(15) will advance approximately 25mm (1”)

Ripping a plank

1. When ripping a plank, stop cutting before reaching the jaws (Image AF)

2. Remove the workpiece and re-clamp with sufﬁcient amount of the cut beyond

the jaws, so that you can drop in your saw to recommence your cut

3. Before clamping, insert a spacer slightly thicker than your saw

cut, at the jaw area, to keep the cut open (Image AG)

Clamping square tubing

• Square tubing or similar can be clamped diagonally into the jaws using

the V-grooves for easier, more precise sawing (Image AH)

Note: Use the V-grooves in the urethane jaws to securely hold your material.

Sharpening chainsaws

• SuperJaws is ideal for clamping a chainsaw or chain

blade while sharpening the teeth (Image AI)

Note: If sharpening a chainsaw, use two wooden blocks, either side of the bar, to ensure

the clamping jaws are clear of the chain, which can then be rotated as each tooth is ﬁled.

Outdoor use

• SuperJaws is ideal for outdoor use. However, if SuperJaws gets

wet, it is important to dry the tool to prevent corrosion. Also re-

apply any oil or grease that may have been affected by rain

330105_Z1MANPRO1.indd 7 09/12/2016 11:53

Triton SJA200 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info