775390
1
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
 

Pantalla en
blanco
El ciclocomputador está en modo de
envío. Pulse un botón.
La pila se ha agotado, o no se ha instalado
correctamente. Instale una pila adecuada.
Datos erró-
neos
El imán está desalineado o demasiado
lejos. Reajuste la posición del imán y
del sensor.
La pila está a punto de agotarse.
Reemplace la pila.
Ninguna
velocidad
actual
El imán está desalineado o demasiado
lejos. Reajuste la posición del imán y
del sensor.
La velocidad
no es cor-
recta.
El tamaño de la rueda es incorrecto.
Restablezca el ciclocomputador.
El sensor no lee el imán correctamente.
Reajuste la alineación del imán y del
sensor.
Ninguna
cadencia
El imán no lee el sensor correctamente.
Reajuste la alineación del imán y del
sensor.
Los contactos entre el ciclocomputador
y la base no se tocan porque el ciclo-
computador no se encuentra en la base.
Reinstálelo.
Ningún
ritmo
cardíaco
La pila de la correa de ritmo cardíaco está
a punto de agotarse. Reemplace la pila.
La correa de ritmo cardíaco no está en
contacto con la piel. Humedézcala y
colóquela bien.
“Error” de
empareja-
miento
Asegúrese de que el ciclocomputador y el
sensor están a una distancia inferior a 3
pies (1 m) entre sí.
Compruebe la pila del sensor.

Si el ciclocomputador proporciona
información errónea, es posible que se esté
agotando la pila. Reemplace las pilas siempre
que el ciclocomputador no funcione bien, o
cada 6 meses. Al adquirir pilas nuevas, lo
mejor es que se lleve las antiguas con usted a
la tienda.
CR2032, pila de litio, 3 voltios
Si se quita la pila, el ciclocomputador reesta-
blecerá automáticamente los totales de función
a cero. Una vez instalada la nueva pila, puede
ajustar los totales manualmente, pero debe
haber anotado estos valores antes de quitar
la pila.

1. Quite el ciclocomputador de la base.
2. Busque la tapa del compartimiento para pilas.
3. Gírela en el sentido contrario al de las agujas
del reloj un cuarto de vuelta (F5).
4. Retire la tapa, dejando la pila al descubierto.
Tenga cuidado de no perder la anilla de goma que sirve como sello.
5. Quite la pila antigua.
6. Inserte la pila nueva con la ‘cruz’ y la etiqueta
identificativa señalando hacia arriba (F6).
7. Vuelva a colocar la tapa del compartimiento
para pilas (y el anillo de sello) y gire un cuarto
de vuelta en el sentido de las agujas del reloj.

Trek Bicycle Corporation garantiza todos los
ciclocomputadores Incite contra defectos en
mano de obra y materiales.
Esta garantía cubre los modelos de ciclocom-
putador de Trek Incite 6i, 8i, 9i, ACH t ACH
Digital durante un periodo de dos años desde
la fecha de venta.
Esta garantía no cubre el desgaste y uso
normal, incluyendo la duración de la vida de
la batería.
• El montaje incorrecto
• La instalación de piezas o accesorios no
pretendidos originalmente para, o no compati-
bles con el componente según se vende
• Daños o fallos debidos a accidente, mal uso,
abuso o negligencia.
Esta garantía queda anulada en su integridad
por cualquier modificación del componente o
de sus piezas.
Esta garantía está limitada expresamente a
la reparación o cambia del artículo defectuoso
y es el único remedio de la garantía. Esta
garantía se extiende desde la fecha de compra,
se aplica solamente al propietario original y
no es transferible. Trek no se hace respon-
sable de daños consecuentes ni fortuitos.
Algunos estados no permiten la exclusión de
daños consecuentes o fortuitos, por lo que la
exclusión anterior puede que no se le aplique
a usted.
Las reclamaciones según está garantía deben
hacerse a través de un distribuidor autorizado.
Es necesaria la prueba de compra. Esta
garantía concede a los consumidores derechos
legales específicos y dichos derechos pueden
variar de lugar a lugar. Esta garantía no afecta
a los derechos reglamentarios del consumidor.


F4 F5 F6 F8
F3
700 x 20 2086 26 x 1.5 2010
700 x 23 2096 26 x 1.90 2045
700 x 25 2105 26 x 1.95 2050
700 x 28 2136 26 x 2.0 2055
700 x 32 2155 26 x 2.1 2068
700 x 35 2168 26 x 2.2 2075
700 x 38 2180 Custom
0000 - 2999
F7
F1
A
Mode
F2
A: Mode button
B: Set button
C: Scroll buttons
C
Scroll
B
Set


25.4
26.0
31.8
1.0 -
3.0mm
2. Pulse los botones de desplazamiento izquierdo y derecho 4
cambia el icono de la rueda.



La velocidad actual se muestra siempre.
1. Pulse repetidamente el botón Modo o el botón Ajuste hasta
SPEED.
2. Pulse repetidamente los botones de desplazamiento hasta AVG
y MAX.
• AVG: velocidad media
• El monitor de ritmo indica si la velocidad actual es
superior o inferior al valor AVG.
• MAX: velocidad máxima
 4
Mantenga pulsados los botones Modo y Ajuste 4 se restablece
a 0.00.

1. Pulse repetidamente el botón Modo o el botón Ajuste hasta la
velocidad.
2. Mantenga pulsado el botón Ajuste 4 aparece el icono de la
rueda.
3. Pulse repetidamente el botón Ajuste 4 Rueda 1 o rueda 2.
4. Pulse el botón de desplazamiento para confirmar la selección.
5. Pulse repetidamente los botones de desplazamiento hasta
alcanzar el tamaño de rueda preferido.
MENÚ DE
TAMAÑO
DE RUEDA
TAMAÑO DE RUEDA
PERSONALIZADO
6. Pulse el
botón Ajuste
para selecci-
onar.
7. Pulse el
botón Modo
4 aparece
la pantalla
de velocidad.
6. Determine la circunferencia de la
rueda (F8).
7. Pulse repetidamente el botón de
desplazamiento hasta el número de
4 cifras.
8. Mantenga pulsado el botón Ajuste 4
parpadea el primer dígito.
9. Pulse repetidamente el botón de
desplazamiento hasta el valor.
10. Pulse el botón Ajuste para
confirmar la selección 4 parpadea
4 el siguiente dígito.
11. Repita los pasos 9 y 10 para el
resto de dígitos.
12. Pulse el botón Modo 4 aparece la
pantalla SPD.
Para ajustar el tamaño de la otra rueda, siga los mismos pasos, pero en el paso 3
seleccione la otra rueda.


1. Pulse repetidamente el botón Modo o el botón Ajuste hasta
seleccionar CLOCK.
2. Pulse repetidamente los botones de desplazamiento hasta
seleccionar el reloj (00:00P) o la hora de conducción
(00:00:00).

1. Pulse repetidamente el botón Modo o el botón Ajuste hasta
seleccionar CLOCK.
2. Mantenga pulsado el botón Ajuste para confirmar la selección
4 parpadea 12 (horas del reloj).
3. Pulse repetidamente los botones de desplazamiento hasta
seleccionar 12 y 24.
4. Pulse el botón Ajuste para confirmar la selección 4 parpadea
la hora (A o P).
5. Pulse repetidamente los botones de desplazamiento hasta
seleccionar la hora.
6. Pulse el botón Ajuste para confirmar la selección 4 parpadean
los minutos.
7. Pulse repetidamente los botones de desplazamiento de
minutos.
8. Pulse el botón Ajuste para confirmar la selección 4 parpadea
la pantalla del reloj.


1. Pulse repetidamente el botón Modo o el botón Ajuste hasta
seleccionar ODOMETER.
2. Pulse repetidamente los botones de desplazamiento hasta
seleccionar TRP y TTL.

1. Pulse repetidamente el botón Modo o el botón Ajuste hasta
seleccionar ODOMETER.
2. Pulse repetidamente los botones de desplazamiento hasta
seleccionar TTL.
3. Mantenga pulsado el botón Ajuste 4 parpadea el primer
dígito.
4. Pulse repetidamente los botones de desplazamiento hasta
seleccionar el número que desee.
5. Pulse el botón Ajuste para confirmar la selección 4 parpadea
4 el siguiente dígito.
6. Repita los pasos 4 y 5 hasta que haya seleccionado todos los
dígitos 4 aparece la pantalla TTL.


1. Pulse repetidamente el botón Modo o el botón Ajuste hasta
seleccionar ODOMETER.
2. Pulse repetidamente los botones de desplazamiento hasta
seleccionar TRP.
3. Mantenga pulsado el botón Ajuste 4 parpadea MPH.
4. Pulse repetidamente los botones de desplazamiento hasta
seleccionar KMH o MPH.
5. Pulse el botón Ajuste para confirmar la selección 4 parpadea
Fº.
6. Pulse repetidamente los botones de desplazamiento hasta
seleccionar F° o C° y seleccione el paso 7 para el modelo de su
ciclocomputador:
LINK LINK TEAM
7. Pulse el
botón
Ajuste para
confirmar
la selección
4 aparece
La pantalla
TRP.
7. Pulse el botón Ajuste para confirmar
la selección 4 aparece _CAd
(cadencia) con OFF u ON parpade-
ando.
8. Pulse repetidamente los botones de
desplazamiento hasta seleccionar
OFF u ON.
9. Pulse el botón Ajuste para confirmar
la selección 4 aparece _Hr (ritmo
cardíaco) con OFF u ON parpade-
ando.
10. Pulse repetidamente los botones
de desplazamiento hasta seleccionar
OFF u ON.
11. Pulse el botón Ajuste para
confirmar la selección 4 parpadea
4 La pantalla TRP.

El ciclocomputador Link Team puede mostrar la cadencia
(CAd) o el ritmo cardíaco (Hr). Para utilizar una de estas
funciones o ambas, debe fijar la función en ON (véase
“Unidades y medición” arriba).
Si una función se ajusta en OFF, el ciclocomputador no
intentará EMPAREJARSE o CONECTARSE con ese sensor.

Para utilizar esta función, debe ajustar la función CADENCE
en ON (véase “Unidades y medición” arriba).

1. Pulse repetidamente el botón Modo hasta seleccionar Cadence.
2. Pulse repetidamente los botones de desplazamiento hasta
seleccionar CUR, AVG o MAX.

1. Pulse repetidamente el botón Modo hasta seleccionar Cadence.
2. Mantenga pulsados los botones Modo y Ajuste 4 Se restablece
en 000.

Para utilizar esta función, debe adquirir la correa de ritmo
cardíaco opcional de su proveedor. Asimismo, debe ajustar
la función de ritmo cardíaco en ON (véase “Unidades y
medición” arriba).

1. Pulse repetidamente el botón Modo o el botón Ajuste hasta
seleccionar Heart Rate.
2. Pulse repetidamente los botones de desplazamiento hasta
seleccionar CUR, AVG, MAX o ZONE.

1. Pulse repetidamente el botón Modo hasta seleccionar HEART
RATE.
2. Mantenga pulsados los botones Modo y Ajuste 4 se restablece
en 000.

1. Pulse repetidamente el botón Modo hasta seleccionar Heart
Rate.
2. Pulse repetidamente los botones de desplazamiento hasta
seleccionar ZONE.
a. Aparece el tiempo en la zona.
b. Aparece el tiempo por encima de la zona.
c. Aparece el tiempo por debajo de la zona.

1. Pulse repetidamente el botón Modo hasta seleccionar Heart
Rate.
2. Mantenga pulsado el botón Ajuste 4 aparece SET ZONE 4
parpadea el primer dígito del límite superior.
3. Pulse repetidamente los botones de desplazamiento para
cambiar el valor.
4. Pulse el botón Ajuste para confirmar la selección 4 parpadea
4 el segundo dígito.
5. Pulse repetidamente los botones de desplazamiento para
cambiar el valor.
6. Pulse el botón Ajuste para confirmar la selección 4 parpadea
el tercer dígito.
7. Pulse el botón Ajuste para confirmar la selección 4 parpadea
el límite inferior.
8. Repita los pasos del 3 al 7 para seleccionar el límite inferior 4
aparece la pantalla de zona.


Presione firmemente el ciclocomputador (no la base) hacia
atrás (F3).

Lea detenidamente este manual y guárdelo para futura
referencia. Si no comprende la información de este
manual o tiene alguna pregunta sobre su ciclocom-
putador Incite que este manual no cubre, consulte con su
distribuidor Trek o póngase en contacto con nosotros en:
Trek Bicycle Corporation
Attn: Customer Service
801 W. Madison Street
Waterloo, Wisconsin 53594, Estados Unidos
http://www.trekbikes.com 920.478.4670


Cuando vaya en bicicleta, no mire al ciclocom-
putador durante períodos prolongados de tiempo
(F1). Si no se fija en la carretera, podría chocar
contra algún obstáculo, lo que le haría perder el
control y caer.


Hay cuatro botones (F2):
A: Modo
B: Ajuste
C: Desplazamiento (dos botones: arriba y abajo)
Existen tres maneras de utilizar los botones:
Pulsar: pulsar una vez.
Pulsar repetidamente: pulsar repetidamente las veces
necesarias.
Mantener: mantener pulsado durante dos o tres segundos.

CLOCK
CLK
TME
Hora del día, que aparece en horas y minutos, u
hora de conducción, que muestra los segundos.
Formato de 12 horas (con AM/PM) o de 24
horas
Lectura máxima: 23:59 (reloj) o 23:59:59 (hora
de conducción)
ODOMETER
ODO
Distancia conducida, que se muestra en millas o
kilómetros.
TRP: trayecto (desde el último reinicio)
TTL: total desde el último restablecimiento
Lectura máxima: 99.999
SPEED Siempre muestra la velocidad actual de la bicicleta
en millas por hora (MPH) o kilómetros por hora
(KMH).
AVG: velocidad media desde el último reinicio,
mostrando hasta las decenas.
MAX: valor máximo desde el último reinicio
Lecturas máximas: 80,5 mph o 129,6 kph
PACER Se muestra siempre. Indica si la velocidad actual
es más rápida o más lenta que la velocidad media.
Se indica mediante una flecha hacia arriba
(más rápido) o una fecha hacia abajo (más
lento)..
TEMPERATURE Se muestra siempre.
Indica la temperatura actual, en Fahrenheit o
Celsius en números enteros.
Lectura mínima: -2° F +/-2°, -19° C +/-1°
Lectura máxima: 140° F +/-2°, 60° C +/-1°
WHEEL
SELECTION
Se muestra siempre (F4).
Indica la configuración de piñón que utiliza el
ciclocomputador.
Rueda 1
INCITE
ACH
Rueda 2
INCITE
ACH

CADENCE Revoluciones del juego de bielas por minuto.
Aparece en números enteros.
Lectura máxima: 240
AVG: cadencia media desde el último reinicio
MAX: cadencia máxima desde el último reinicio
HEART RATE
HR
Ritmo cardíaco en latidos por minuto.
CUR: actual
AVG: ritmo cardíaco medio desde el último
restablecimiento
MAX: ritmo cardíaco máximo desde el último
restablecimiento
ZONE: las flechas indican si el ritmo cardíaco
se encuentra dentro, por encima o por debajo
de una zona establecida
BACKLIGHT Proporciona retroiluminación a la pantalla durante
5 segundos.
Para activarla, mantenga pulsado el botón
Modo.

Si el ciclocomputador es nuevo (o si ha reemplazado la
pila), se debe programar para su elección de unidades
y se deben identificar las señales correctas del sensor
(velocidad para Link; también cadencia y ritmo cardíaco
para Link Team). Siga los cuatro pasos de instalación
rápida, emparejamiento, conexión y reinicio.

1. Instale la pila o pulse el botón de restablecimiento (el
pequeño botón plateado en la parte trasera del ciclocom-
putador, debajo de la tapa del compartimiento para pilas.
Aparecerá el icono de rueda 1 y “700-23”.
2. Pulse repetidamente el botón de desplazamiento para
cambiar el tamaño de la rueda.
Seleccione el tamaño del neumático mediante el gráfico (F7) o establezca un
tamaño de rueda personalizado.
3. Pulse el botón Ajuste para seleccionar 4 parpadea KMH
o MPH.
4. Pulse repetidamente el botón de desplazamiento para
cambiar el valor.
5. Pulse el botón Ajuste para confirmar la selección 4
parpadea Fº o Cº.
6. Pulse repetidamente el botón de desplazamiento para
cambiar el valor.
7. Pulse el botón Ajuste para confirmar la selección 4
parpadea 4 12 (horas del reloj).
8. Pulse repetidamente los botones de desplazamiento para
seleccionar el reloj de 12 ó 24 horas.
9. Pulse el botón Ajuste para confirmar la selección 4
parpadea la hora (A o P).
10. Pulse repetidamente los botones de desplazamiento para
cambiar la hora.
11. Pulse el botón Ajuste para confirmar la selección 4
parpadean los minutos.
12. Pulse repetidamente los botones de desplazamiento para
cambiar los minutos.
13. Pulse el botón Ajuste para confirmar la selección 4
parpadea SPEED PAIR?.
14. Sigua los pasos de “Emparejamiento”.

Link y Link Team son ciclocomputadores digitales
de 2,4 Ghz. Reciben transmisiones codificadas desde
los sensores para la velocidad, la cadencia y el ritmo
cardíaco. Para que el ciclocomputador pueda recibir estas
transmisiones, el ciclocomputador y el sensor se deben
reconocer entre como un par. Un par utiliza un código
exclusivo, de modo que los sensores cercanos no causen
interferencias.
Cada sensor (velocidad, cadencia y ritmo cardíaco)
envía un tipo de señal específico. En un modo determi-
nado, el ciclocomputador sólo reconocerá las señales
de ese tipo de sensor. Por ejemplo, el ciclocomputador
sólo reconocerá los datos de velocidad del sensor de
velocidad.
Existen dos maneras de realizar el procedimiento de
emparejamiento: el paso 14 de “1. Instalación rápida” o
Bajo demanda. El método Instalación rápida borra todos
los datos del ciclocomputador. El procedimiento Bajo
demanda no borra los datos. Para realizar la instalación
inicial, siga la instalación rápida.


1. Coloque el ciclocomputador en la bicicleta o a 3 pies (1
metro) del sensor.
2. Haga que el sensor envíe una señal (gire la rueda de la
bicicleta para la velocidad, gire las bielas para la cadencia
o colóquese la correa para el ritmo cardíaco).
3. Mantenga pulsado el botón 4 PAIR... 4
LINK LINK TEAM
4Aparece
la
pantalla
de
velocidad.
Suelte el
botón.
4 Aparece CADENCE PAIR?.
4. Haga que el sensor envíe una
señal (gire las bielas para la
cadencia).
5. Mantenga pulsado el botón 4
PAIR... 4 Aparece la pantalla de
velocidad. Suelte el botón.


Si reemplaza la pila de un sensor o de la unidad
principal, o cambia los sensores, utilice el procedimiento
Bajo demanda.
1. Coloque el ciclocomputador en la bicicleta o a 3 pies (1
metro) del sensor.
2. Haga que el sensor envíe una señal (gire la rueda de la
bicicleta para la velocidad, gire las bielas para la cadencia
o colóquese la correa para el ritmo cardíaco).
3. Pulse ambos botones de desplazamiento 4 PAIR?
4. Mantenga pulsado el botón 4 PAIR... 4 consulte la tabla
siguiente para Link y Link Team.

Cuando se deja de pedalear (o se quita la correa
de ritmo cardíaco de Link Team), el sensor no envía
ninguna señal. Si el ciclocomputador no encuentra
ninguna señal, realiza una búsqueda.
Tras cinco minutos de búsqueda, el ciclocomputador se
desconecta de los sensores, detiene la búsqueda y pasa a
modo de espera. Esto ahorra energía de la pila, ya que la
búsqueda utiliza esa energía. Tras 20 minutos de inactiv-
idad, el ciclocomputador pasa a modo suspendido.
Desde el modo en espera o suspendido, para empezar a
recibir datos se debe conectar el ciclocomputador a cada
sensor. Existen dos formas de conectarse:

1. Envíe las señales del sensor (gire la rueda, pedalee la
biela y/o colóquese la correa de ritmo cardíaco).
2. Pulse cualquier botón.
El ciclocomputador se conectará automáticamente a cada sensor. Esto puede
tardar algunos segundos. Si el ciclocomputador no encuentra una señal, después
de 20 segundos pasará al siguiente sensor, con el orden: velocidad, cadencia, ritmo
cardíaco.
Si el ciclocomputador no se puede conectar a ningún sensor, en la pantalla aparece
“- -”. Siga las instrucciones “Para conectar desde el modo de espera” o consulte
la sección de solución de problemas.

1. Haga que los sensores envíen señales (gire la rueda,
pedalee la biela y/o colóquese la correa de ritmo cardíaco).
2. Mantenga pulsado el botón Ajuste y el botón Modo 4
parpadea “0” 4 ”0” aparece sin parpadear 4 aparece el
valor.
3. Suelte los botones.
Si aparece ---, compruebe la distancia entre el ciclocomputador y el sensor, y entre
el sensor y el imán. Si el ciclocomputador sigue sin conectarse, siga los pasos para
emparejar el ciclocomputador o consulte la sección de solución de problemas.


Su ciclocomputador graba dos conjuntos de datos: el
total de datos desde el momento en el que se instaló, y
los datos del recorrido desde el último reinicio (el ritmo
cardíaco se ajusta aparte: consulte la sección Ritmo
cardíaco):
• ODOMETER TRP
• SPEED AVG, MAX
• CADENCE AVG, MAX
• CLOCK (hora de conducción)

1. Pulse repetidamente el botón Modo hasta CLOCK.
2. Pulse repetidamente el botón de desplazamiento hasta la
hora de conducción.
3. Mantenga pulsados los botones Ajuste y Modo.
La configuración de hora de conducción muestra ‘00:00.00’, lo que indica que el
modo de recorrido se ha puesto a cero.
4. Suelte los botones.

El ciclocomputador puede recopilar datos para dos
tamaños de rueda diferentes. Consulte “Uso de las
funciones, velocidad”. Estas instrucciones muestran
como cambiar al otro tamaño de rueda.
1. Pulse repetidamente el botón Modo hasta ODOMETER.

Please read this manual carefully and save it for
future reference. If you do not understand the
information in this manual, or you have a question
about your Incite computer that this manual does not
cover, consult your Trek dealer, or contact us at:
Trek Bicycle Corporation
Attn: Customer Service
801 W. Madison Street
Waterloo, Wisconsin 53594 USA
http://www.trekbikes.com 920.478.4670

While riding your bicycle, do not stare at the
computer for long periods of time (F1). If you do
not watch the road, you could hit an obstacle,
which may cause you to lose control and fall.


There are four buttons (F2):
A- Mode
B- Set
C- Scroll (two buttons: up and down)
There are three ways to use the buttons:
Push- press once
Cycle - press repeatedly as needed
Hold- press and hold in for two or three seconds

CLOCK
CLK
TME
Time of day, displays in hours and minutes, or
Ride Time showing seconds.
12-hour (with AM/PM) or 24-hour format
Highest reading: 23:59 (Clock) or 23:59:59
(Ride Time)
ODOMETER
ODO
Distance ridden, displays in miles or kilometers.
TRP-Trip (since last ReStart)
TTL- Total since last Reset
Highest reading: 99,999
SPEED
SPD
Always displays current speed of the bicycle
in miles per hour (MPH) or kilometers per
hour (KMH)
AVG- Average speed since last ReStart, dis-
played to tenths.
MAX- Highest value since last ReStart
Highest readings: 80.5mph or 129.6kph
PACER Always displays. Indicates whether current
speed is faster or slower than average speed
Displayed by arrow pointing up (faster) or
down (slower).
TEMPERATURE Always displays
Current temperature displayed in Fahrenheit
or Celsius in whole numbers.
Lowest reading: -2° F +/-2°, -19° C +/-1°
Highest reading: 140° F +/-2°, 60° C +/-1°
WHEEL
SELECTION
Always displays (F4)
Indicates which wheel setting is in use by
computer
Wheel 1
INCITE
ACH
Wheel 2
INCITE
ACH
ALTITUDE Height relative to sea level.
CUR- Current
TRP- Trip (since last Restart)
TTL- Total gained since last ReSet
MAX- Highest value since last ReSet
Effective range:
FT -1250 to +30180
M -381 to +9200
CADENCE
CAD
RPM
Revolutions of the crankset per minute
Displays in whole numbers
Highest reading: 240.
AVG- Average cadence since last ReStart
MAX- Maximum cadence since last ReStart
HEART RATE
HR
Rate of heart in beats per minute
CUR- Current
AVG- Average heart rate since last ReSet
MAX- Maximum heart rate since last ReSet
ZONE- Arrows indicate whether your heart
rate is within a set zone, above the zone,
or below the zone

COMPASS Direction of travel

BACKLIGHT Provides backlight to display for 5 seconds.
To activate, Hold the Mode button.

When the computer is new (or if you have replaced
the battery) the computer must be programmed for
your choice of units and the correct sensor signals
must be identified (Speed, Cadence, and Heart Rate).
Follow the four steps of Quick Set-up, Pair, Connect,
and ReStart.

1. Install the battery or push the Reset button (the tiny
silver button on back of computer, below the battery
cover) 4 Wheel 1 icon and “700-23” appear.
2. Cycle the Scroll buttons to change wheel size.
Select the tire size, use the chart (F7), or set a custom wheel size.
3. Push the Set button to select 4 KMH or MPH flashes.
4. Cycle the Scroll buttons to change.
5. Push the Set button to select 4 or C° flashes.
6. Cycle the Scroll buttons to change.
7. Push the Set button to select 4 12 (hour clock)
flashes.
8. Cycle the Scroll buttons to 12 or 24 hour clock.
9. Push the Set button to select 4 Hour flashes (A or P)
10. Cycle the Scroll buttons to change the Hour.
11. Push the Set button to select 4 Minutes flashes.
12. Cycle the Scroll buttons to change the Minutes.
13. Push the Set button to select 4 SPEED PAIR?
flashes.
14. Follow the steps in “2. Pair.”

The Alpine and the ACH Digital are 2.4Ghz digital
computers. They receive coded transmissions from the
sensors for Speed, Cadence, and Heart rate. Before
the computer can receive these transmissions, the
computer and the sensor must recognize each other as
a Pair. A Pair uses a unique code so that other nearby
sensors will not cause interference.
The sensor for each mode (Speed, Cadence, and
Heart rate) sends a specific type of signal. In a given
mode, the computer will only recognize signals from
that type of sensor. As an example, the computer will
only recognize Speed data from the Speed sensor.
Note: A combined speed/cadence sensor sends only one signal, so with this
feature only one operation is necessary to Pair or Connect both modes.
There are two methods for the Pair procedure:
• Quick Set-up erases all computer data. For the initial
set up, follow the Quick Set-up.
• On Demand procedure does not erase data.

1. Place the computer on the bike, or within 3 feet (1
meter) of the sensor.
2. Make the sensor send a signal (spin the bicycle wheel
for Speed, spin the cranks for Cadence, or wear the
heart rate strap for Heart Rate).
3. Push the Set button 4 PAIR... 4
 
4. The Speed screen
appears. You are
ready to ride.
The Alpine computer is
shipped with the Cadence
sensor and Heart Rate
sensor turned Off. To turn
On these features, follow
the instructions in “Units
and Measurement.” Then
repeat these instructions, but
follow the steps for the ACH
Digital to Pair the Cadence
and Heart Rate sensors.
4. CAD PAIR? appears.
5. Make the cadence
sensor send a signal.
6. Push the Set button
4 PAIR... 4HR
PAIR? appears.
7. Make the Heart Rate
sensor send a signal.
8. Push the Set button
4 PAIR... 4 the
SPEED screen
appears. You are
ready to ride.

If you replace the battery in a sensor or the
main unit, or change sensors, use the On Demand
procedure.
1. Place the computer on the bike, or within 3 feet (1
meter) of the sensor.
2. Cycle the Mode button to the mode you want to pair
(Speed, Cadence, or Heart Rate).
3. Make the sensor for that mode send a signal.
4. Press both Scroll buttons 4 PAIR?
5. Push the Set button 4 PAIR... 4 The screen of the
next mode appears. You are ready to ride.

When you stop riding (or remove the heart rate
strap) the sensor does not send a signal. When the
computer can not find a signal, it searches.
After five minutes of searching, the computer discon-
nects from the sensor(s), stops searching, and goes
into Standby mode. In Standby mode, the speed shows
“——”. This saves battery power, because the search
uses extra battery power.
After 20 minutes of inactivity, the computer goes
into Sleep mode. In sleep mode, the screen is blank.
From Standby or Sleep mode, to start receiving data
you must Connect the computer with each sensor.
There are two ways to Connect:

1. Send the sensor signals (roll the wheel, pedal the
crank, and/or wear the heart rate strap within range).
If only one sensor is sending, the computer will only connect to that one signal
in that one mode.
2. Push any button.
The computer will automatically connect to each sensor. This may take a few
seconds. If the computer cannot find a signal, after 20 seconds it will move to
the next sensor in order: Speed, Cadence, Heart rate.
If the computer cannot connect to any sensor, the screen displays “- -”. Follow
the instructions “To Connect from Standby,” or see Troubleshooting.

1. Make the sensors send signals (roll the wheel, pedal the
crank, and/or wear the heart rate strap within range).
If only one sensor is sending, the computer will only connect to that one signal
in that one mode.
2. Hold the Set button and the Mode button 4 ”0” flashes
3. Release the buttons 4 ”0” shows without flashing 4
the value appears.
If --- appears, the computer did not connect with the sensor. Check the distance
of the computer to the sensor, and the sensor to the magnet. If the computer still
does not Connect, follow the steps to Pair the computer, or see Troubleshooting.

Your computer records two sets of data: Total data
from the time it was installed and Trip data from the
last ReStart (Heart Rate data is set separately- see the
Heart Rate section):
• ODOMETER TRP
• SPEED AVG, MAX
• CADENCE AVG, MAX
• CLOCK (Ride Time)
• ALTIMETER

1. Cycle the Mode button to CLOCK.
2. Cycle the Scroll buttons to Ride Time (six digits, e.g.
00:21:13).
3. Hold the Set button and the Mode button.
Ride Time setting reads ‘00:00.00’ indicating trip mode is set to zero.
4. Release the buttons.

The computer can collect data for two different
wheel sizes. These instructions show how to change to
the other wheel size. To set the other wheel size, see
“Using the Features, Speed.”
1. Cycle the Mode button to ODOMETER.
2. Push the left Scroll button and the right Scroll button
4 the wheel icon changes.



Current speed always displays.
1. Cycle the Mode button or the Set button to SPEED.
2. Cycle the Scroll buttons to AVG and MAX.
• AVG - average speed
• Pacer indicates if current speed is above or
below AVG
• MAX- maximum speed
 4
Hold the Mode button and the Set button 4 Resets to
0.00.

1. Cycle the Mode button or the Set button to Speed.
2. Hold the Set button 4 Wheel icon appears.
3. Cycle the Set button 4 Wheel 1 or Wheel 2.
4. Push the Scroll button to select.
5. Cycle the Scroll buttons to your preferred wheel size.
WHEEL SIZE
MENU CUSTOM WHEEL SIZE
6. Push the Set
button to
select.
7. Push the
Mode button
4 Speed
screen
appears.
6. Determine the wheel circum-
ference (F8)
7. Cycle the Scroll buttons to
the 4-digit number.
8. Hold the Set button 4 the
first digit flashes
9. Cycle the Scroll buttons to
the value
10. Push the Set button to
select 4 the next digit
flashes
11. Repeat step 9 and step 10
for the other digits
12. Push the Mode button 4
SPD screen appears.
To set the other Wheel Size, repeat the steps, but in Step 3 choose the other wheel.


1. Cycle the Mode button or the Set button to CLOCK.
2. Cycle the Scroll buttons to Clock (00:00P) or Ride Time
(00:00:00).

1. Cycle the Mode button or the Set button to CLOCK.
2. Hold the Set button 4 12 (hour clock) flashes.
3. Cycle the Scroll buttons to 12 and 24.
4. Push the Set button to select 4 Hour flashes (A or P)
5. Cycle the Scroll buttons to Hour.
6. Push the Set button to select 4 Minutes flashes.
7. Cycle the Scroll buttons to Minutes.
8. Push the Set button to select 4 Clock screen appears.


1. Cycle the Mode button or the Set button to
ODOMETER.
2. Cycle the Scroll buttons to TRP and TTL.

1. Cycle the Mode button or the Set button to
ODOMETER.
2. Cycle the Scroll buttons to TTL.
3. Hold the Set button 4 First digit flashes.
4. Cycle the Scroll buttons to the preferred number.
5. Push the Set button to select 4 the next digit flashes.
6. Repeat Step 4 and Step 5 until you have selected all
digits 4 TTL screen appears.


1. Cycle the Mode button or the Set button until
ALTITUDE appears.
2. Cycle the Scroll buttons to see the data:
• TTL- total altitude gain since ReSet
• CUR- current altitude
• TRP- altitude gain since last ReStart
• MAX- maximum altitude

1. Cycle the Mode button to ALTITUDE.
2. Cycle the Scroll buttons to CUR.
3. Hold the Set button 4 Current elevation appears, and
the + or - (above or below sea level) is flashing.
4. Cycle the Scroll buttons to your preferred value ( +
or -).
5. Push the Set button to select 4 the first digit flashes.
6. Repeat steps 4 and 5 until all digits have been set 4
Altitude CUR screen appears.

1. Cycle the Mode button to Altitude.
2. Cycle the Scroll buttons to TTL.
3. Hold Set 4 Total elevation gain appears with the first
digit flashing.
4. Cycle the Scroll buttons until the first digit shows your
preferred value.
5. Push the Set button to select 4 the next digit flashes.
6. Repeat steps 4 and 5 until all digits have been set 4
the computer returns to the Altitude TTL screen.


1. Cycle the Mode button or the Set button to
ODOMETER.
2. Cycle the Scroll buttons to TRP.
3. Hold the Set button 4 KPH flashes.
4. Cycle the Scroll buttons to KMH or MPH.
5. Push the Set button to select 4 flashes.
6. Cycle the Scroll buttons to F° or C°.
7. Push the Set button to select 4 CAd (cadence) appears
with OFF or ON flashing.
8. Cycle the Scroll buttons to OFF or ON.
If you turn a feature to OFF, the battery will last longer.
9. Push the Set button to select 4 Hr (heart rate)
appears with OFF or ON flashing.
10. Cycle the Scroll buttons to OFF or ON.
11. Push the Set button to select 4 TRP screen appears.

Your computer can display Cadence (CAd) or Heart
Rate (Hr). To use one or both of these features,
you must set the feature to ON (see “Units and
Measurement” above). If a function is turned OFF, the
computer will not try to PAIR or CONNECT with that
sensor. If the sensor is not connected, the computer
will not show the data for that mode.

To use this feature, you must set the CADENCE
feature to ON (see “Units and Measurement” above).

1. Cycle the Mode button or Set button to Cadence.
2. Cycle the Scroll buttons to CUR, AVG, or MAX.
4
1. Cycle the Mode button to Cadence.
2. Hold the Mode button and the Set button 4 Resets
to 000.

To use this feature, purchase the optional heart rate
strap from your dealer. Also, you must set the Heart
Rate feature to ON (see “Units and Measurement”
above).

1. Cycle the Mode button or the Set button to Heart Rate.
2. Cycle the Scroll buttons to CUR, AVG, MAX, or ZONE.
4
1. Cycle the Mode button to HEART RATE.
2. Hold the Mode button and the Set button 4 Resets
to 000.

1. Cycle the Mode button to Heart Rate.
2. Cycle the Scroll buttons to ZONE.
a. In-zone time appears.
b. Above-zone time appears.
c. Below-zone time appears.

1. Cycle the Mode button to Heart Rate.
2. Hold the Set button 4 SET ZONE appears 4 first
digit of Upper limit flashes
3. Cycle the Scroll buttons to change number
4. Push the Set button to select 4 second digit flashes
5. Cycle the Scroll buttons to change number
6. Push the Set button to select 4 third digit flashes
7. Push the Set button to select 4 Lower limit flashes
8. Repeat steps 3-7 to select lower limit 4 Zone screen
appears.


1. Cycle the Mode button to COMPASS 4 the Compass
and Speed screen appears.
2. Cycle the Scroll buttons to degrees (numbers) or
direction (letters).

The declination is the difference between the
direction of the magnetic north pole and true north
pole. Before Setup, the DEC is set at 0.
The declination must be set and the computer must
be calibrated so that it can find true North. This
procedure must be done after a Reset, changing the
batteries, or moving the computer a large geographic
distance.
When you set the DEC on the computer, you must
indicate whether the magnetic pole is East or West
of the true north pole, and the degrees. The correct
declination for an area is usually listed on a map of
the area.
1. Cycle the Mode button to COMPASS.
2. Hold the Set button 4 DEC-- appears.
If you do not want to set the declination, push the Mode button 4 CAL appears
(see steps 8-10 below). If the computer is already calibrated, push the Mode
button again 4 the Compass and Speed screen appears.
3. Cycle the Set button to DEC-W or DEC-E.
4. Cycle the Scroll buttons to the declination value.
5. Push the Mode button to select 4 CAL appears.



6. Push the Mode
button 4 the
Compass and
Speed screen
appears.
Make sure there are no magnetic
items or metal near the computer.
6. With the face of the
computer level, push the
Set button, then rotate
the computer in a full
circle.
7. Push the Set button
4END appears.
8. Push the Mode button 4
the Compass and Speed
screen appears.

To remove the computer from its mount on the
handlebar, press firmly on the computer (not on the
base) in a rearward direction (F3).

Blank screen Computer is in shipping mode. Push a button.
Battery is dead, or installed incorrectly. Reinstall
good battery.
Erratic data Magnet misaligned or too far away. Re-adjust mag-
net and sensor placement.
Battery power is low. Replace battery.
No current
speed
Magnet misaligned or too far away. Re-adjust mag-
net and sensor placement.
Speed is
incorrect.
Wheel size is incorrect. Reset computer.
Sensor is not reading magnet properly. Readjust
magnet and sensor alignment.
No cadence Magnet is not reading sensor properly. Readjust
magnet and sensor alignment.
Contacts between computer and base are not touch-
ing because computer is not on base. Reinstall.
No heart
rate
Heart rate strap battery power is low. Replace
battery.
Heart rate strap is not contacting skin. Moisten and
reposition.
Pair “Error” Make sure the computer and the sensor are closer
than 3 feet (1 M)
Check sensor battery
“——” dis-
plays
The computer has lost connection with the sensor.
See the section “3. Connect.

If the computer is giving erratic information, a
battery may be running low. Replace the batteries
whenever the computer malfunctions, or every 6
months. When purchasing new batteries, it is best to
take the old batteries to the store with you.
CR2032, lithium cell, 3 volts
When the battery is removed, the computer automati-
cally resets function totals to Zero. After installing a
new battery, you can manually set your totals, but you
must note those values before removing the battery.

1. Remove the computer from its base.
2. Identify the battery cover.
3. Rotate in a counter-clockwise direction about one-
quarter turn (F5).
4. Lift the battery cover, exposing the battery.
Be careful to avoid losing the rubber O-ring seal.
5. Remove the old battery.
6. Insert the new battery with the ‘cross’ and identifying
label pointing up (F6).
7. Replace the battery cover (and O-ring seal) and turn
one-quarter turn clockwise.

Trek Bicycle Corporation warrants each new Incite computer
against defects in workmanship and materials.
This warranty covers
Trek Incite computer models for a period of two years from the
date of sale.
This warranty does not cover
Normal wear and tear, including the length of battery life
Improper assembly
Installation of parts or accessories not originally intended
for, or compatible with the component as sold
Damage or failure due to accident, misuse, abuse, or neglect
This warranty is void in its entirety by any modification of the
component or its parts.
This warranty is expressly limited to the repair or replacement
of a defective item and is the sole remedy of the warranty. This
warranty extends from the date of purchase, applies only to the
original owner, and is not transferable. Trek is not responsible
for incidental or consequential damages. Some states do not
allow the exclusion of incidental or consequential damages, so
the above exclusion may not apply to you.
Claims under this warranty must be made through an authorized
dealer. Proof of purchase is required.
This warranty gives the consumer specific legal rights, and those
rights may vary from place to place. This warranty does not affect
the statutory rights of the consumer.

1.0-8.0 mm

1. Determine the wheel circumference (F8)
2. Cycle the Scroll button to the 4-digit number.
3. Hold the Set button4the first digit flashes
4. Cycle the Scroll button to the value
5. Push the Set button to select4the next digit
flashes
6. Repeat Step 4 and Step 5 for the other digits
7. Return to Step 3 of Quick Set-up

Lesen Sie sich dieses Handbuch sorgfältig durch und
bewahren Sie es gut auf. Wenn Sie etwas nicht verstehen,
oder wenn Sie Fragen zu Ihrem Incite-Computer haben, die
das Handbuch nicht beantwortet, wenden Sie sich an Ihren
Trek-Händler oder an uns unter:
Trek Bicycle Corporation
Attn: Customer Service
801 W. Madison Street
Waterloo, Wisconsin 53594, USA
http://www.trekbikes.com 920.478.4670


Schauen Sie beim Radfahren nicht zu lange auf den
Computer (F1). Wenn Sie nicht auf die Straße schauen,
übersehen Sie womöglich ein Hindernis, verlieren die
Kontrolle und stürzen.


Das Gerät weist vier Tasten auf (F2):
A – Modus
B – Einstellen
C – Bildlauf (zwei Tasten: auf und ab)
Die Tasten können auf drei Arten verwendet werden:
Einmal – Taste einmal drücken
Mehrmals – Taste mehrmals drücken, bis gewünschte Anzeige
erscheint
Halten – Taste einige Sekunden gedrückt halten

UHR
CLK
TME
Uhrzeit in Stunden und Minuten oder Fahrtdauer in
Stunden, Minuten und Sekunden.
12-Stunden-Format (mit AM/PM) oder 24-Stunden-
Format
Höchster Anzeigewert: 23:59 (Uhr) oder
23:59:59 (Fahrtdauer)
KILOMETERZÄHLER
ODO
Zurückgelegte Strecke in Meilen oder Kilometern.
TRP – seit dem letzten Neustart (Trip)
TTL – seit dem letzten Zurücksetzen (Total)
Höchster Anzeigewert: 99.999
GESCHWINDIGKEIT
ODO
Permanente Anzeige. Aktuelle Geschwindigkeit in
Meilen pro Stunde (MPH) oder Kilometer pro Stunde
(KMH)
AVG – Durchschnittsgeschwindigkeit seit dem letz-
ten Neustart, Anzeige zehntelgenau.
MAX – Höchstgeschwindigkeit seit dem letzten
Neustart
Höchster Anzeigewert: 80.5 mph oder 129.6
kmh
SCHRITTGEBER Permanente Anzeige. Zeigt an, ob die aktuelle
Geschwindigkeit über oder unter dem Durchschnitt
liegt.
Anzeige von Pfeil nach oben (schneller) oder
Pfeil nach unten (langsamer)
TEMPERATUR Permanente Anzeige
Aktuelle Temperatur in Fahrenheit oder Celsius in
ganzen Zahlen.
Niedrigster Anzeigewert: -2 °F +/-2 °, -19 °C +/-1 °
Höchster Anzeigewert: 140 °F +/-2°, 60 °C
+/-1°
RADAUSWAHL Permanente Anzeige (F4)
Zeigt an, auf welche Radmaße der Computer
eingestellt ist.
Wheel 1
INCITE
ACH
Wheel 2
INCITE
ACH

TRITTFREQUENZ Kurbelumdrehungen pro Minute
Anzeige in ganzen Zahlen
Höchster Anzeigewert: 240.
AVG – Durchschnittsfrequenz seit dem letzten
Neustart
MAX – Maximale Trittfrequenz seit dem letzten
Neustart
PULS
HR
Puls in Schlägen pro Minute
CUR – Aktueller Puls
AVG – Durchschnittlicher Puls seit dem letzten
Zurücksetzen
MAX – Maximaler Puls seit dem letzten
Zurücksetzen
ZONE – Richtungspfeile, die anzeigen, ob Ihr
Puls innerhalb, oberhalb oder unterhalb des
gewünschten Pulsbereichs liegt
HINTER-
GRUNDBEL-
EUCHTUNG
Schaltet die Hintergrundbeleuchtung für 5 Sekunden
ein.
Zum Aktivieren Modustaste gedrückt halten.

Nach dem Einbau des Computers (oder nach einem
Batteriewechsel) müssen die gewünschten Maßenheiten
eingestellt und die korrekten Sensorsignale (Link:
Geschwindigkeit, Link Team: Geschwindigkeit, Trittfrequenz
und Puls) identifiziert werden. Führen Sie die in den vier
Abschnitten „Einrichten“, „Koppeln“, Verbinden“ und „Neu
startenbeschriebenen Schritte aus.

1. Batterie einlegen oder Reset-Knopf (den kleinen
silbernen Knopf unterhalb der Batterieabdeckung an der
Geräterückseite) drücken4Das Wheel 1-Symbol und die
Anzeige „700-23“ erscheint.
2. Mit den Bildlauftasten die gewünschte Radgröße auswählen.
Stellen Sie anhand des Diagramms (F7) die korrekte Radgröße fest, oder wählen Sie eine
andere Radgröße aus.
3. Taste „Einstellen“ einmal drücken4KMH oder MPH blinkt.
4. Mit den Bildlauftasten die gewünschte Einheit auswählen.
5. Taste „Einstellen“ einmal drücken4 oder C° blinkt.
6. Mit den Bildlauftasten die gewünschte Einheit auswählen.
7. Taste „Einstellen“ einmal drücken__12 oder 24 blinkt.
8. Mit den Bildlauftasten die 12- oder 24-Stunden-Anzeige
auswählen.
9. Taste „Einstellen“ einmal drücken4A oder P blinkt
10. Mit den Bildlauftasten die Tageszeit (A = Vormittag, P =
Nachmittag) einstellen.
11. Taste „Einstellen“ einmal drücken4Die Minutenanzeige
blinkt.
12. Mit den Bildlauftasten die Minuten einstellen.
13. Taste „Einstellen“ einmal drücken4SPEED PAIR? blinkt.
14. Die unter „Koppeln“ beschriebenen Schritte ausführen.

Link und Link Team sind digitale 2,4-GHz-Computer.
Sie erhalten kodierte Daten von den Sensoren für
Geschwindigkeit, Trittfrequenz und Puls. Damit der Computer
diese Daten empfangen kann, müssen sich der Computer und
der Sensor gegenseitig als Paar erkennen. Ein Paar verwendet
jeweils einen eigenen Code, damit andere Sensoren im
Empfangsbereich keine Störungen verursachen.
Jeder Sensor (Geschwindigkeit, Trittfrequenz und Puls)
sendet einen bestimmten Signaltyp. Je nach eingestelltem
Modus erkennt der Computer nur die Signale des entspre-
chenden Sensors. So verarbeitet der Computer beispiels-
weise im Geschwindigkeitsmodus nur die Daten des
Geschwindigkeitssensors.
Die Koppelung kann auf zweierlei Weise vorgenommen
werden: entweder mit dem in Schritt 14 der Anleitung
„1. Einrichten“ beschriebenen oder mit dem On Demand-
Verfahren. Beim Einrichten werden alle Computerdaten
gelöscht. Beim On Demand-Verfahren gehen keine Daten
verloren. Bei der erstmaligen Einrichtung gehen Sie wie
unter „Einrichten“ beschrieben vor.

1. Den Computer am Fahrrad anbringen oder maximal 1 Meter
vom Sensor entfernt halten.
2. Sensorsignal erzeugen (Geschwindigkeit: Laufrad drehen;
Trittfrequenz: Tretkurbel drehen; Puls: Brustband des
Pulsmessers anlegen).
3. Taste „Einstellen“ gedrückt halten4PAIR... 4
LINK LINK TEAM
4 Die
Geschwindigkeit-
sanzeige erscheint.
Taste loslassen.
4 CADENCE PAIR? erscheint.
4. Sensorsignal erzeugen
(Trittfrequenz: Tretkurbel
drehen).
5. Taste „Einstellen“ gedrückt
halten 4 PAIR... 4 Die
Geschwindigkeitsanzeige
erscheint. Taste loslassen.

Wenn Sie einen Sensor bzw. die Batterie eines Sensors oder
des Computers selbst auswechseln, verwenden Sie das On
Demand-Verfahren.
1. Den Computer am Fahrrad anbringen oder maximal 1 Meter
vom Sensor entfernt halten.
2. Sensorsignal erzeugen (Geschwindigkeit: Laufrad drehen;
Trittfrequenz: Tretkurbel drehen; Puls: Brustband des
Pulsmessers anlegen).
3. Beide Bildlauftasten drücken 4 PAIR?
4. Taste „Einstellen“ gedrückt halten 4 PAIR... 4 Fahren Sie
wie in der oben stehenden Tabelle unter Link bzw. Link Team
beschrieben fort.

Wenn Sie anhalten (oder das Brustband des Link Team-
Pulsmessers abnehmen), sendet der Sensor kein Signal mehr.
Das Ausbleiben des Signals veranlasst den Computer, eine
Signalsuche zu starten.
Nach fünf Minuten bricht der Computer die Suche ab,
beendet die Sensorverbindung(en) und wechselt in den
Standby-Modus. Auf diese Weise wird die Batterie geschont,
da die Signalsuche einen hohen Stromverbrauch verursacht.
Nach 20-minütiger Inaktivität wechselt der Computer in den
Sleep-Modus.
Im Standby- oder Sleep-Modus muss der Computer erst
wieder mit den Sensoren verbunden werden, damit er Daten
empfangen kann. Die Verbindung kann auf zweierlei Weise
hergestellt werden:

1. Sensorsignal erzeugen (Laufrad drehen, Tretkurbel drehen
und/oder Brustband des Pulsmessers anlegen).
2. Beliebige Taste drücken.
Der Computer stellt automatisch die Verbindung zu dem jeweiligen Sensor her. Dieser
Vorgang kann einige Sekunden in Anspruch nehmen. Wenn der Computer nach 20 Sekunden
noch kein Signal gefunden hat, testet er den jeweils nächsten Sensor (Geschwindigkeit ->
Trittfrequenz -> Puls).
Wenn der Computer zu keinem Sensor eine Verbindung herstellen kann, erscheint im
Display die Anzeige „- -“. Gehen Sie wie unter „Verbindung im Standby-Modus herstellen“
beschrieben vor, oder lesen Sie die Hinweise im Abschnitt „Problembehebung“.

1. Sensorsignal erzeugen (Laufrad drehen, Tretkurbel drehen
und/oder Brustband des Pulsmessers anlegen).
2. Tasten „Einstellen“ und „Modus“ gedrückt halten 4 ”0” blinkt
4 ”0” wird dauerhaft angezeigt 4 Der Wert erscheint.
3. Tasten loslassen
Wenn „---“ angezeigt wird, überprüfen Sie den Abstand zwischen Computer und Sensor
sowie zwischen Sensor und Magnet. Wenn der Computer noch immer keine Verbindung
herstellen kann, führen Sie die unter „Koppeln“ beschriebenen Schritte aus, oder lesen Sie
die Hinweise im Abschnitt „Problembehebung“.


Ihr Computer zeichnet zwei Datensätze auf, nämlich
zum einen die kumulierten Daten seit dem Einbau (bzw.
Zurücksetzen) des Geräts und zum anderen die Trip-Daten
seit dem letzten Neustart (Puls wird separat eingestellt – siehe
Abschnitt „Puls“):
• KILOMETERZÄHLER TRP
• GESCHWINDIGKEIT AVG, MAX
• TRITTFREQUENZ AVG, MAX
• UHR (Fahrtdauer)

1. Mit der Modustaste in den UHR-Modus wechseln.
2. Mit den Bildlaufleisten die Fahrtdauer auswählen.
3. Tasten „Einstellen“ und „Modus“ gedrückt halten.
Der Fahrtdaueranzeige springt auf „00:00.00“, um anzuzeigen, dass die Trip-Daten auf
null gestellt wurden.
4. Tasten loslassen

Der Computer kann Daten für zwei verschiedene Radgrößen
aufzeichnen. Siehe Abschnitt Verwenden der Funktionen,
Geschwindigkeit“. Führen Sie die folgenden Schritte aus, um
zwischen den beiden Radgrößen umzuschalten.
1. Mit der Modustaste in den KILOMETERZÄHLER-Modus
wechseln.
2. Linke und rechte Bildlauftaste drücken 4 Das Radsymbol
wechselt.



Die aktuelle Geschwindigkeit wird permanent angezeigt.
1. Mit der Taste „Modus“ oder „Einstellenin den
GESCHWINDIGKEIT-Modus wechseln.
2. Mit den Bildlauftasten die Einstellung AVG oder MAX
auswählen.
• AVG – Durchschnittsgeschwindigkeit
• Der Schrittgeber zeigt an, ob die aktuelle
Geschwindigkeit über oder unter der Durchschnittsgesch
windigkeit AVG liegt
• MAX Höchstgeschwindigkeit
 4
Tasten „Modus“ und „Einstellengedrückt halten 4 Anzeige
springt auf 0.00.

1. Mit der Taste „Modus“ oder „Einstellenin den
GESCHWINDIGKEIT-Modus wechseln.
2. Taste „Einstellen“ gedrückt halten 4 Das Radsymbol wird
angezeigt.
3. Mit der Taste „Einstellen“ die gewünschte Radgrößenposition
auswählen 4 Wheel 1 oder Wheel 2.
4. Mit der Bildlauftaste die gewählte Einstellung aktivieren.
5. Mit den Bildlauftasten die gewünschte Radgröße einstellen.

Veuillez lire ce manuel avec attention et le conserver
comme document de référence. Si vous ne comprenez pas
des informations fournies dans ce manuel ou si vous avez
des questions sur votre compteur Incite auxquelles ce
manuel ne répond pas, renseignez-vous auprès de votre
revendeur Trek ou contactez-nous à l’adresse :
Trek Bicycle Corporation
Attn : Customer Service
801 W. Madison Street
Waterloo, Wisconsin 53594 États-Unis
http://www.trekbikes.com 920.478.4670

Lorsque vous roulez, évitez de consulter le compteur
trop longtemps (Figure 1). Si vous ne regardez pas la
route, vous risquez de percuter un obstacle, donc de
perdre le contrôle et de chuter.


Les boutons sont au nombre de quatre (Figure 2) :
A - Mode
B - Config
C- Défil (deux boutons : haut et bas)
Ces boutons s’utilisent de trois manières :
en appuyant dessus une fois ;
en appuyant dessus autant de fois que nécessaire ;
en les maintenant enfoncés pendant deux ou trois secondes

HORLOGE
CLK
TME
Heure du jour affichée en heures et minutes, ou
Ride Time (Durée du parcours) avec les secondes.
Format 12 heures (avec AM/PM) ou 24 heures
Valeur maximum : 23:59 (Horloge) ou 23:59:59
(Durée du parcours)
ODOMÈTRE
ODO
Distance parcourue, affichée en miles ou en
kilomètres.
TRP : distance depuis la dernière réinitialisa-
tion partielle.
TTL : distance totale depuis la dernière réini-
tialisation totale.
Valeur maximum : 99,999
VITESSE Vitesse actuelle du vélo toujours affichée en miles/
heure (MPH) ou en kilomètres/heure (KMH).
AVG : vitesse moyenne depuis la dernière réini-
tialisation partielle (nombre à une décimale).
MAX : valeur la plus élevée depuis la dernière
réinitialisation partielle.
Valeurs maximum : 80,5 mph ou 129,6 kmh
INDICATEUR DE
RYTHME
Toujours affiché. Indique si la vitesse actuelle est
supérieure ou inférieure à la vitesse moyenne.
Est indiqué par une flèche orientée vers le
haut (vitesse supérieure) ou orientée vers
le bas (vitesse inférieure).
(TEMPÉRATURE Toujours affichée.
Température actuelle affichée en degrés
Fahrenheit ou Celsius (nombres entiers).
Valeur minimum : -2° F +/- 2°, -19° C +/- 1°
Valeur maximum : 140° F +/- 2°, 60° C +/-
SÉLECTION DE
ROUE
Toujours affichée (Figure 4).
Indique le paramètre de roue actuellement
utilisé par le compteur.
Roue 1
INCITE
ACH
Roue 2
INCITE
ACH

CADENCE Tours de pédalier par minute.
Valeur affichée en nombre entier.
Valeur maximum : 240.
AVG : cadence moyenne depuis la dernière réini-
tialisation partielle.
MAX : cadence maximum depuis la dernière
réinitialisation partielle.
RYTHME
CARDIAQUE
HR
Nombre de pulsations cardiaques par minute.
CUR : valeur actuelle.
AVG : nombre moyen de pulsations cardiaques
depuis la dernière réinitialisation totale.
MAX : nombre maximum de pulsations cardi-
aques depuis la dernière réinitialisation totale.
ZONE : flèches indiquant si le rythme cardiaque
est dans une zone définie, au-dessus ou au-
dessous de cette zone.
RÉTROÉCLAIRAGE Affichage de l’écran par rétroéclairage pendant
5 secondes.
Pour l’activer, maintenez le bouton Mode
enfoncé.

Lorsque vous utilisez le compteur pour la première
fois (ou si vous avez remplacé la pile), vous devez
sélectionner les unités à utiliser et identifier les signaux
de capteur appropriés (Vitesse pour Link, ainsi que
Cadence et Rythme cardiaque pour Link Team). Suivez les
quatre procédures : Configuration rapide, Appariement,
Connexion et Réinitialisation partielle.

1. Installez la pile ou appuyez sur le bouton de réinitialisation
totale (le petit bouton couleur argent situé à l’arrière du
compteur, sous le couvercle de la pile) 4 L’icône Roue 1 et
« 700-23 » apparaissent.
2. Appuyez plusieurs fois sur le bouton Défil pour changer de
taille de roue.
Sélectionnez la taille du pneu, utilisez le graphique (Figure 7) ou saisissez une taille
de roue personnalisée.
3. Appuyez sur le bouton Config pour valider votre choix 4
KMH ou MPH clignote.
4. Appuyez plusieurs fois sur le bouton Défil pour changer la
valeur.
5. Appuyez sur le bouton Config pour valider votre choix 4
F° ou clignote.
6. Appuyez plusieurs fois sur le bouton Défil pour changer la
valeur.
7. Appuyez sur le bouton Config pour valider votre choix 4
12 (heure) clignote.
8. Appuyez plusieurs fois sur les boutons Défil pour basculer
entre les formats 12 heures et 24 heures.
9. Appuyez sur le bouton Config pour valider votre choix 4
L’heure clignote (A ou P)
10. Appuyez plusieurs fois sur le bouton Défil pour changer
l’heure.
11. Appuyez sur le bouton Config pour valider votre choix 4
Les minutes clignotent.
12. Appuyez plusieurs fois sur le bouton Défil pour changer
les minutes.
13. Appuyez sur le bouton Config pour valider votre choix 4
SPEED PAIR? clignote.
14. Suivez les étapes décrites dans la section « Appariement ».

Les compteurs Link et Link Team sont des compteurs
numériques cadencés à 2,4 GHz. Les capteurs leur
envoient des signaux codés sur la vitesse, la cadence et le
rythme cardiaque. Pour que le compteur puisse recevoir
ces informations, ce dernier et le capteur doivent se
reconnaître l’un l’autre comme une paire. Une paire utilise
un code unique, empêchant ainsi les autres capteurs à
proximité de générer des interférences.
Chaque capteur (Vitesse, Cadence et Rythme cardiaque)
envoie un signal d’un type bien particulier. Dans un
mode donné, le compteur ne reconnaît que les signaux
émis par le type de capteur en question. Par exemple, il
ne reconnaît que les données de vitesse envoyées par le
capteur Vitesse.
Vous pouvez effectuer la procédure d’appariement comme
expliqué à l’étape 14 de la section « 1. Configuration
rapide » ou à la demande. La configuration rapide
efface toutes les données en mémoire. La procédure à
la demande conserve les données. Lors de la première
utilisation du compteur, suivez la procédure Configuration
rapide.

1. Placez le compteur sur le vélo ou à moins de 1 mètre du
capteur.
2. Faites envoyer un signal par le capteur (en faisant tourner
la roue pour envoyer une vitesse, en tournant le pédalier
pour envoyer une cadence ou en appliquant la ceinture
thoracique sur votre poitrine pour envoyer un rythme
cardiaque).
3. Maintenez le bouton Config enfoncé 4 PAIR... apparaît 4
LINK LINK TEAM
4 L’écran
Speed
(Vitesse)
apparaît.
Relâchez le
bouton.
4 CADENCE PAIR? apparaît.
4. Faites envoyer un signal par le
capteur (en tournant le pédalier
pour obtenir une cadence).
5. Maintenez le bouton Config
enfoncé.4 PAIR... apparaît4
L’écran Speed (Vitesse) apparaît.
Relâchez le bouton.

Si vous remplacez la pile dans un capteur ou dans
l’unité principale, ou si vous changez de capteur, suivez la
procédure à la demande.
1. Placez le compteur sur le vélo ou à moins de 1 mètre du
capteur.
2. Faites envoyer un signal par le capteur (en faisant tourner
la roue pour envoyer une vitesse, en tournant le pédalier
pour envoyer une cadence ou en appliquant la ceinture
thoracique sur votre poitrine pour envoyer un rythme
cardiaque).
3. Appuyez sur les boutons Défil. 4 PAIR? apparaît.
4. Maintenez le bouton Config enfoncé. 4 PAIR... apparaît.
4 Consultez le tableau ci-dessus pour les modèles Link et
Link Team.

Lorsque vous arrêtez de rouler (ou que vous retirez la
ceinture thoracique Link Team), le capteur n’envoie plus
de signaux. Lorsque le compteur ne détecte aucun signal,
il lance une recherche.
Après cinq minutes, il se déconnecte du ou des capteurs,
interrompt la recherche et se met en attente. Ceci permet
d’optimiser l’autonomie de l’appareil, car la recherche
consomme de l’énergie. Après 20 minutes d’inactivité, le
compteur se met en veille.
Pour réactiver la réception de données à partir du mode
d’attente ou de veille, vous devez connecter le compteur
à chaque capteur. Pour ce faire, deux possibilités s’offrent
à vous :

1. Faites envoyer des signaux par un ou plusieurs capteurs
(en faisant tourner la roue, en tournant le pédalier et/ou en
appliquant sur votre poitrine la ceinture thoracique).
2. Appuyez sur un bouton quelconque.
Le compteur se connecte automatiquement à chaque capteur. L’opération peut
prendre quelques secondes. Si le compteur ne détecte aucun signal dans un délai
de 20 secondes, il passe au capteur suivant dans l’ordre décrit ci-après : Vitesse,
Cadence, Rythme cardiaque.
Si le compteur ne parvient pas à se connecter à un capteur, l’écran affiche « - - ».
Suivez les instructions de la procédure « Pour connecter le compteur à partir du mode
d’attente » ou consultez la section Dépannage.

1. Faites envoyer des signaux par un ou plusieurs capteurs
(en faisant tourner la roue, en tournant le pédalier et/ou en
appliquant sur votre poitrine la ceinture thoracique).
2. Maintenez les boutons Config et Mode enfoncés. 4 « 0 »
clignote. 4 « 0 » s’affiche sans clignoter. 4 La valeur
apparaît.
3. Relâchez les boutons.
Si --- apparaît, vérifiez la distance entre le compteur et le capteur, et entre le capteur
et l’aimant. Si le compteur ne se connecte toujours pas, suivez la procédure permet-
tant d’apparier le compteur ou consultez la section Dépannage.


Le compteur enregistre deux sortes de données : les
totaux cumulés depuis son installation et les données
de trajet enregistrées depuis la dernière réinitialisation
partielle (les données concernant le rythme cardiaque
sont traitées à part, reportez-vous à la section Rythme
cardiaque) :
• ODOMETER (ODOMÈTRE) TRP
• SPEED (VITESSE) AVG, MAX
• CADENCE (CADENCE) AVG, MAX
• CLOCK (HORLOGE) (Ride Time - Durée du parcours)


1. Appuyez plusieurs fois sur le bouton Mode jusqu’à afficher
CLOCK (HORLOGE).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
Ride Time (Durée du parcours).
3. Maintenez les boutons Config et Mode enfoncés.
Le paramètre Ride Time (Durée du parcours) affiche la valeur « 00:00.00 », indiquant
que le mode parcours est réinitialisé.
4. Relâchez les boutons.

Le compteur peut collecter les données pour deux tailles
de roue. Reportez-vous aux instructions figurant dans la
section « Vitesse » dans « Utilisation des fonctions ». Elles
vous indiquent comment sélectionner une autre taille de
roue.
1. Appuyez plusieurs fois sur le bouton Mode jusqu’à afficher
ODOMETER (ODOMÈTRE).
2. Appuyez sur le bouton Défil situé à gauche et sur le bouton
Défil situé à droite. 4 L’icône de roue change.



La vitesse actuelle est toujours affichée.
1. Appuyez plusieurs fois sur le bouton Mode ou Config
jusqu’à afficher SPEED (VITESSE).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
AVG et MAX.
• AVG : vitesse moyenne
• L’indicateur de vitesse indique si la vitesse actuelle est
supérieure ou inférieure à la moyenne.
• MAX : vitesse maximum
 4 
Maintenez les boutons Mode et Config enfoncés. 4 Les
valeurs sont remises à 0.00.

1. Appuyez plusieurs fois sur le bouton Mode ou Config jusqu’à
afficher SPEED (VITESSE).
2. Maintenez le bouton Config enfoncé. 4 L’icône de roue
apparaît.
3. Appuyez plusieurs fois sur le bouton Config. 4 Roue 1 ou
Roue 2 apparaît.
4. Appuyez sur le bouton Défil pour sélectionner la valeur.
5. Appuyez plusieurs fois sur le bouton Défil pour choisir votre
taille de roue préférée.
TAILLE DE
ROUE TAILLE DE ROUE PERSONNALISÉE
6. Appuyez sur
le bouton
Config pour
valider votre
choix.
7. Appuyez sur
le bouton
Mode 4
L’écran
Speed
(Vitesse)
apparaît..
6. Mesurez la circonférence de la
roue (Figure 8).
7. Appuyez plusieurs fois sur le bouton
Défil jusqu’à afficher le nombre à
quatre chiffres.
8. Maintenez le bouton Config enfoncé
4 Le premier chiffre clignote.
9. Appuyez plusieurs fois sur le bouton
Défil jusqu’à afficher la valeur
correcte.
10. Appuyez sur le bouton Config pour
valider votre choix 4 Le chiffre
suivant clignote.
11. Répétez les étapes 9 et 10 pour les
autres chiffres.
12. Appuyez sur le bouton Mode. 4
L’écran SPD apparaît.
Pour définir la taille de l’autre roue, répétez la procédure en choisissant l’autre roue à l’étape 3.


1. Appuyez plusieurs fois sur le bouton Mode ou Config jusqu’à
afficher CLOCK (HORLOGE).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à
afficher Clock (Horloge) (00:00P) ou Ride Time (Durée du
parcours) (00:00:00).

1. Appuyez plusieurs fois sur le bouton Mode ou Config jusqu’à
afficher CLOCK (HORLOGE).
2. Appuyez sur le bouton Config. 4 12 (heure) clignote.
3. Appuyez plusieurs fois sur les boutons Défil pour basculer
entre 12 et 24.
4. Appuyez sur le bouton Config pour valider votre choix. 4
L’heure clignote (A ou P)
5. Appuyez plusieurs fois sur les boutons Défil pour sélectionner
l’heure.
6. Appuyez sur le bouton Config pour valider votre choix. 4 Les
minutes clignotent.
7. Appuyez plusieurs fois sur les boutons Défil pour sélectionner
les minutes.
8. Appuyez sur le bouton Config pour valider votre choix. 4
L’écran Clock (Horloge) apparaît.


1. Appuyez plusieurs fois sur le bouton Mode ou Config jusqu’à
afficher ODOMETER (ODOMÈTRE).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
TRP et TTL.

1. Appuyez plusieurs fois sur le bouton Mode ou Config jusqu’à
afficher ODOMETER (ODOMÈTRE).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
TTL.
3. Maintenez le bouton Config enfoncé. 4 Le premier chiffre
clignote.
4. Appuyez plusieurs fois sur les boutons Défil pour choisir le
chiffre.
5. Appuyez sur le bouton Config pour valider votre choix 4 Le
chiffre suivant clignote.
6. Répétez les étapes 4 et 5 jusqu’à sélectionner tous les chiffres.
4 L’écran TTL apparaît.


1. Appuyez plusieurs fois sur le bouton Mode ou Config jusqu’à
afficher ODOMETER (ODOMÈTRE).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
TRP.
3. Maintenez le bouton Config enfoncé. 4 MPH clignote.
4. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
KMH ou MPH.
5. Appuyez sur le bouton Config pour valider votre choix. 4
clignote.
6. Appuyez plusieurs sur les boutons Défil jusqu’à afficher F°
ou C° et effectuez l’étape 7 correspondant à votre modèle de
compteur :
LINK LINK TEAM
7. Appuyez sur
le bouton
Config pour
valider votre
choix.4
L’écran TRP
apparaît.
7. Appuyez sur le bouton Config
pour valider votre choix.4 CAD
(cadence) apparaît avec OFF ou ON
clignotant.
8. Appuyez plusieurs fois sur les
boutons Défil pour basculer entre
OFF et ON.
9. Appuyez sur le bouton Config pour
valider votre choix.4 Hr (rythme
cardiaque) apparaît avec OFF ou ON
clignotant.
10. Appuyez plusieurs fois sur les
boutons Défil pour basculer entre
OFF et ON.
11. Appuyez sur le bouton Config pour
valider votre choix.4 L’écran TRP
apparaît.

Votre compteur Link Team affiche la cadence (CAd) ou le
rythme cardiaque (Hr). Pour utiliser l’une ou l’autre de ces
fonctions, vous devez la configurer sur ON (reportez-vous à la
section « Unités et mesure » ci-dessus).
Si une fonction est désactivée (OFF), le compteur ne tente
pas de l’apparier ni de la connecter au capteur correspondant.

Pour utiliser cette fonction, vous devez configurer la
fonction CADENCE (CADENCE) sur ON (reportez-vous à la
section « Unités et mesure » ci-dessus).

1. Appuyez plusieurs fois sur le bouton Mode jusqu’à afficher
CADENCE (CADENCE).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
CUR, AVG ou MAX.

1. Appuyez plusieurs fois sur le bouton Mode jusqu’à afficher
CADENCE (CADENCE).
2. Maintenez les boutons Mode et Config enfoncés.4 Les valeurs
sont remises à 000.

Pour utiliser cette fonction, vous devez acheter une ceinture
thoracique chez votre revendeur. Vous devez également
configurer la fonction Rythme cardiaque sur ON (reportez-
vous à la section « Unités et mesure » ci-dessus).

1. Appuyez plusieurs fois sur le bouton Mode ou Config jusqu’à
afficher Heart Rate (Rythme cardiaque).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
CUR, AVG, MAX ou ZONE.

1. Appuyez plusieurs fois sur le bouton Mode jusqu’à afficher
HEART RATE (RYTHME CARDIAQUE).
2. Maintenez les boutons Mode et Config enfoncés.4 Les valeurs
sont remises à 000.

1. Appuyez plusieurs fois sur le bouton Mode jusqu’à afficher
Heart Rate (Rythme cardiaque).
2. Appuyez plusieurs fois sur les boutons Défil jusqu’à afficher
ZONE.
a. Le temps passé à l’intérieur de la zone apparaît.
b. Le temps passé au-dessus de la zone apparaît.
c. Le temps passé au-dessous de la zone apparaît.

1. Appuyez plusieurs fois sur le bouton Mode jusqu’à afficher
Heart Rate (Rythme cardiaque).
2. Maintenez le bouton Config enfoncé.4 SET ZONE (CONFIG
ZONE) apparaît.4 Le premier chiffre de la limite supérieure
clignote.
3. Appuyez plusieurs fois sur les boutons Défil pour le modifier.
4. Appuyez sur le bouton Config pour valider votre choix.4 Le
chiffre suivant clignote.
5. Appuyez plusieurs fois sur les boutons Défil pour le modifier.
6. Appuyez sur le bouton Config pour valider votre choix.4 Le
chiffre suivant clignote.
7. Appuyez sur le bouton Config pour valider votre choix.4 La
limite inférieure clignote.
8. Répétez les étapes 3 à 7 pour configurer la limite inférieure.4
L’écran Zone apparaît.


Appuyez fermement sur le compteur (pas sur la base) vers
l’arrière (Figure 3).

Écran vide Le compteur est en mode expédition. Appuyez sur un
bouton.
La pile est morte ou mal installée. Réinstallez une pile en
état de marche.
Données irré-
gulières
Aimant décalé ou trop éloigné. Ajustez la position de
l’aimant et du capteur.
Niveau faible de la pile. Remplacez la pile.
Aucune
vitesse affi-
chée
Aimant décalé ou trop éloigné. Ajustez la position de
l’aimant et du capteur.
Vitesse incor-
recte
La taille de roue est incorrecte. Réinitialisez le compteur.
Le capteur ne détecte pas correctement l’aimant. Réalignez
l’aimant et le capteur.
Aucune
cadence
Laimant ne détecte pas le capteur correctement. Réalignez
l’aimant et le capteur.
Les contacts du compteur et de la base ne se touchent pas,
car le compteur n’est sur sa base. Replacez-le sur sa base.
Aucun rythme
cardiaque
La pile de la ceinture thoracique chargée de transmettre les
pulsations cardiaques est usagée. Remplacez la pile.
La ceinture thoracique chargée de transmettre les pul-
sations cardiaques n’est pas en contact avec la peau.
Humidifiez-la et remettez-la en place.
Erreur
d’appariement
Vérifiez que le compteur et le capteur sont éloignés de
moins de 1 mètre.
Vérifiez la pile du capteur.

Si le compteur fournit des informations confuses, il se peut
que l’alimentation soit insuffisante. Remplacez la pile en
cas de dysfonctionnement du compteur ou tous les 6 mois.
Lorsque vous achetez une nouvelle pile, il est préférable
d’apporter l’ancienne avec vous au magasin.
Pile au lithium CR2032, 3 volts
Lorsque vous retirez la pile, le compteur remet automatique-
ment les totaux des différentes fonctions à zéro. Une fois la
pile remplacée, vous pouvez reconfigurer manuellement vos
totaux, mais cela implique vous ayez noté leur valeur avant le
retrait de la pile usagée.

1. Retirez le compteur de sa base.
2. Repérez le couvercle de la pile.
3. Faites-le tourner d’un quart de tour dans le sens contraire des
aiguilles d’une montre (Figure 5).
4. Soulevez le couvercle pour accéder à la pile.
Veillez à ne pas perdre le joint torique en caoutchouc.
5. Retirez la pile usagée.
6. Mettez la nouvelle pile en place, le signe + et l’étiquette vers le
haut (Figure 6).
7. Remettez le couvercle (et le joint torique) en place et tournez-le
d’un quart de tour dans le sens des aiguilles d’une montre.

Trek Bicycle Corporation garantit chaque compteur Incite neuf contre les
défauts de matériaux et de fabrication.
Cette garantie couvre les modèles de compteur Trek Incite 6i, 8i, 9i, 11i ;
ACH et ACH Digital pendant une période de deux ans à partir de la date
d’achat.
Cette garantie ne couvre pas l’usure normale du compteur, y compris la
durée de vie de la pile
• Un montage incorrect
• L’installation de pièces ou d’accessoires qui ne sont à l’origine pas
prévus ou compatibles avec le compteur tel qu’il est vendu
• Les dommages ou défaillances occasionnés par un accident, une
mauvaise utilisation, un mauvais traitement ou une négligence.
Toute modification apportée au dispositif ou à ses pièces entraîne
l’annulation de cette garantie dans son intégralité.
Cette garantie est expressément limitée à la réparation ou au remplace-
ment d’un article défectueux ; il s’agit de l’unique recours de la garantie.
Cette garantie commence à courir à partir de la date d’achat, ne s’applique
qu’au propriétaire initial et est incessible. Trek ne peut être tenu pour
responsable des dommages indirects ou accessoires. Certains états (Etats-
Unis) n’autorisent pas l’exclusion des dommages indirects ou accessoires ;
il se peut donc que l’exclusion ci-dessus ne s’applique pas à vous.
Les réclamations au titre de cette garantie doivent être adressées par
l’intermédiaire d’un concessionnaire Trek agréé. Une preuve d’achat est
exigée.
Cette garantie donne au consommateur des droits juridiques spécifiques,
et ces droits peuvent varier d’un endroit à un autre. Cette garantie
n’affecte pas les droits statutaires du consommateur.
RADGRÖSSENMENÜ ANDERE RADGRÖSSE
AUSWÄHLEN
6. Taste „Einstellen
einmal drücken.
7. Modustaste
drücken 4 Die
Geschwindigkeit-
sanzeige erscheint.
6. Radumfang bestimmen (F8)
7. Mit der Bildlauftaste den
4-stelligen Zahlencode
auswählen.
8. Taste „Einstellen“ gedrückt
halten 4 Die erste Stelle
blinkt
9. Mit der Bildlauftaste den
gewünschten Wert einstellen
10. Taste „Einstellen“ einmal
drücken 4 Die nächste Stelle
blinkt
11. Die Schritte 9 und 10
wiederholen, um die Werte
für die übrigen Stellen des
Zahlencodes festzulegen
12. Modustaste drücken 4 Die
Geschwindigkeitsanzeige
erscheint.
Zum Einstellen der anderen Radgröße wiederholen Sie diese Schritte, wählen aber in Schritt 3 die
jeweils andere Position aus.


1. Mit der Taste „Modus“ oder „Einstellenin den UHR-Modus
wechseln.
2. Mit den Bildlauftasten die Uhrzeit (00:00P) oder die Fahrtdauer
(00:00:00) auswählen.

1. Mit der Taste „Modus“ oder „Einstellenin den UHR-Modus
wechseln.
2. Taste „Einstellen“ gedrückt halten___12 oder 24 blinkt.
3. Mit den Bildlauftasten die 12- oder 24-Stunden-Anzeige
auswählen.
4. Taste „Einstellen“ einmal drücken 4A oder P blinkt
5. Mit den Bildlauftasten die Tageszeit (A = Vormittag, P =
Nachmittag) einstellen.
6. Taste „Einstellen“ einmal drücken 4Die Minutenanzeige blinkt.
7. Mit den Bildlauftasten die Minuten einstellen.
8. Taste „Einstellen“ einmal drücken 4Die Uhrzeitanzeige
erscheint.


1. Mit der Taste „Modus“ oder „Einstellenin den
KILOMETERZÄHLER-Modus wechseln.
2. Mit den Bildlauftasten die Einstellung TRP oder TTL auswählen.

1. Mit der Taste „Modus“ oder „Einstellenin den
KILOMETERZÄHLER-Modus wechseln.
2. Mit den Bildlauftasten die Einstellung TTL auswählen.
3. Taste „Einstellen“ gedrückt halten 4Die erste Stelle blinkt.
4. Mit den Bildlauftasten den gewünschten Wert auswählen.
5. Taste „Einstellen“ einmal drücken 4Die nächste Stelle blinkt.
6. Die Schritte 4 und 5 wiederholen, um die Werte für die übrigen
Stellen festzulegen. 4Die TTL-Anzeige erscheint.


1. Mit der Taste „Modus“ oder „Einstellenin den
KILOMETERZÄHLER-Modus wechseln.
2. Mit den Bildlauftasten die Einstellung TRP auswählen.
3. Taste „Einstellen“ gedrückt halten 4MPH blinkt.
4. Mit den Bildlauftasten die Einstellung KMH oder MPH
auswählen.
5. Taste „Einstellen“ einmal drücken 4blinkt.
6. Mit den Bildlauftasten die Einstellung F° oder C° auswählen
und mit dem Ihrem Computermodell entsprechenden Schritt 7
fortfahren.
LINK LINK TEAM
7. Taste
„Einstellen
einmal
drücken
4Die TRP-
Anzeige
erscheint.
7. Taste „Einstellen“ einmal drücken
4Die Trittfrequenzanzeige (CAd)
erscheint, OFF oder ON blinkt.
8. Mit den Bildlauftasten die Einstellung
OFF oder ON auswählen.
9. Taste „Einstellen“ einmal drücken
4Die Pulsanzeige (Hr) erscheint, OFF
oder ON blinkt.
10. Mit den Bildlauftasten die
Einstellung OFF oder ON auswählen.
11. Taste „Einstellen“ einmal drücken
4Die TRP-Anzeige erscheint.

Ihr Link Team-Computer kann die Trittfrequenz (CAd)
oder den Puls (Hr) anzeigen. Um eine oder beide dieser
Funktionen zu verwenden, müssen Sie sie das betref-
fende Leistungsmerkmal aktiveren (ON, siehe Abschnitt
„Maßeinheiten“).
Wenn eine Funktion deaktiviert (OFF) ist, versucht der
Computer nicht, die Koppelung oder Verbindung mit dem
betreffenden Sensor herzustellen.

Um diese Funktion zu verwenden, müssen Sie das betref-
fende Leistungsmerkmal aktiveren (ON, siehe Abschnitt
„Maßeinheiten“).

1. Mit der Modustaste in den TRITTFREQUENZ-Modus wechseln.
2. Mit den Bildlauftasten die Einstellung CUR, AVG oder MAX
auswählen.

1. Mit der Modustaste in den TRITTFREQUENZ-Modus wechseln.
2. Tasten „Modus“ und „Einstellen“ gedrückt halten 4Anzeige
springt auf 000.

Um diese Funktion zu verwenden, benötigen Sie das
als Zubehör bei Ihrem Händler erhältliche Brustband
für den Pulsmesser. Außerdem müssen Sie das betref-
fende Leistungsmerkmal aktivieren (ON, siehe Abschnitt
„Maßeinheiten“).

1. Mit der Taste „Modus“ oder „Einstellenin den PULS-Modus
wechseln.
2. Mit den Bildlauftasten die Einstellung CUR, AVG, MAX oder
ZONE auswählen.

1. Mit der Modustaste in den PULS-Modus wechseln.
2. Tasten „Modus“ und „Einstellen“ gedrückt halten 4Anzeige
springt auf 000.

1. Mit der Modustaste in den PULS-Modus wechseln.
2. Mit den Bildlauftasten die Einstellung ZONE auswählen.
a. Zeit innerhalb des Pulsbereichs erscheint.
b. Zeit oberhalb des Pulsbereichs erscheint.
c. Zeit unterhalb des Pulsbereichs erscheint.

1. Mit der Modustaste in den PULS-Modus wechseln.
2. Taste „Einstellen“ gedrückt halten 4SET ZONE erscheint 4Die
erste Stelle des oberen Grenzwerts blinkt
3. Mit den Bildlauftasten den gewünschten Wert auswählen
4. Taste „Einstellen“ einmal drücken 4Die zweite Stelle blinkt
5. Mit den Bildlauftasten den gewünschten Wert auswählen
6. Taste „Einstellen“ einmal drücken 4Die dritte Stelle blinkt
7. Taste „Einstellen“ einmal drücken 4Die erste Stelle des unteren
Grenzwerts blinkt
8. Wiederholen Sie die Schritte 3 bis 7, um den unteren Grenzwert
festzulegen 4Die Pulsbereichsanzeige erscheint.


Drücken Sie den Computer (nicht die Grundplatte) kräftig nach
hinten (F3).

Leerer Bildschirm Computer ist nicht betriebsbereit. Drücken Sie eine beli-
ebige Taste.
Batterie ist leer oder falsch eingesetzt. Erneuern Sie die
Batterie, oder setzen Sie die vorhandene Batterie kor-
rekt ein.
Unregelmäßige Daten Magnet falsch ausgerichtet oder zu weit entfernt. Justieren
Sie Magnet und Sensor neu.
Batterie schwach. Wechseln Sie die Batterie aus.
Keine Anzeige der aktu-
ellen Geschwindigkeit
Magnet falsch ausgerichtet oder zu weit entfernt. Justieren
Sie Magnet und Sensor neu..
Falsche
Geschwindigkeitsanzeig
Falsche Radgröße eingegeben. Setzen Sie den Computer
zurück.
Sensor erkennt Signale des Magneten nicht korrekt.
Justieren Sie Magnet und Sensor neu.
Keine Anzeige der
Trittfrequenz
Magnet wird vom Sensor nicht korrekt erkannt. Justieren
Sie Magnet und Sensor neu.
Es besteht kein Kontakt zwischen dem Computer und der
Grundplatte, weil der Computer nicht auf der Grundplatte
eingesetzt ist. Computer einsetzen.
Keine Anzeige der
Pulsfrequenz
Batterie im Brustband des Pulsmessers schwach. Wechseln
Sie die Batterie aus.
Brustband des Pulsmessers hat keinen Hautkontakt.
Feuchten Sie den Sensor des Brustbands an und justieren
Sie das Brustband neu.
Koppelungsfehler Stellen Sie sicher, dass Computer und Sensor maximal 1 m
voneinander entfernt sind.
Prüfen Sie die Sensorbatterie.

Wenn der Computer unregelmäßige Informationen ausgibt,
ist möglicherweise eine Batterie zu schwach. Wechseln Sie die
Batterie aus, sobald der Computer Fehlfunktionen zeigt, oder
aber alle 6 Monate. Beim Kauf neuer Batterien sollten Sie die
alten im Laden zurückgeben.
CR2032, Lithium-Batterie, 3 V
Beim Entfernen der Batterie setzt der Computer automatisch
alle Funktionen auf null zurück. Nach dem Einsetzen der neuen
Batterie können Sie Ihre Gesamtwerte manuell eingeben. Dazu
müssen Sie sich die Werte jedoch vor dem Batteriewechsel
notieren.

1. Entfernen Sie den Computer von der Grundplatte.
2. Suchen Sie die Batterieabdeckung.
3. Drehen Sie die Batterieabdeckung um neunzig Grad gegen den
Uhrzeigersinn (F5).
4. Nehmen Sie die Batterieabdeckung ab, um die Batterie
freizulegen.
Achten Sie darauf, dass der zum Abdichten verwendete O-Ring nicht verloren geht.
5. Entfernen Sie die alte Batterie.
6. Setzen Sie die neue Batterie so ein, dass die Seite mit dem
Pluszeichen (+) und dem Markenzeichen nach oben zeigt (F6).
7. Setzen Sie die Batterieabdeckung wieder ein (O-Ring nicht
vergessen!), und drehen Sie die Abdeckung um neunzig Grad im
Uhrzeigersinn.

Die Trek Bicycle Corporation gewährleistet, dass jedes Incite-Produkt frei
von Produktions- und Materialfehlern ist.
Diese Gewährleistung gilt für die Trek Incite Computermodelle vom Typ 6i, 8i, 9i, 11i, ACH,
und ACH Digital für eine Dauer von zwei Jahren ab Kaufdatum.
Normale Abnutzung und Verschleiß, einschließlich der Lebensdauer der Batterie sind in der
Gewährleistung nicht enthalten.
• Unsachgemäße Montage
• Montage von Zubehörteilen und Accessoires, die mit dem gekauften
Gerät nicht kompatibel sind und nicht ursprünglich zur Verwendung an dem
gekauften Gerät gedacht waren.
• Beschädigungen oder Defekte in Folge unsachgemäßen Einsatzes,
Unfalls oder Nachlässigkeit.
Die Gewährleistung verliert ihre volle Gültigkeit bei Veränderungen an dem
Gerät oder Teilen davon.
Die Gewährleistung ist ausdrücklich auf die Reparatur oder den Austausch
von defekten Teilen beschränkt, die das einzige Rechtsmittel der
Gewährleistung sind. Die Gewährleistung beginnt am Tag des Kaufs, gilt
nur für den Eigentümer und ist nicht übertragbar. Trek übernimmt keine
Haftung für Unfall- oder Folgeschäden. In einigen Staaten ist der Ausschluss
von Unfall- ,bzw. Folgeschäden nicht erlaubt, somit besteht die Möglichkeit,
dass der o.a. Ausschluss für Sie nicht zutreffend ist.
Sämtliche in Folge dieser Gewährleistung auftretenden Ansprüche sind
durch einen autorisierten Fachhändler abzuwickeln. Dabei ist die Vorlage
des Kaufnachweises erforderlich.
Durch diese Gewährleistung werden dem Verbraucher bestimmte, durch das
Gesetz vorgegebene Rechte gewährt, die sich je nach Standort unterscheiden
können. Der durch das Gesetz vorgesehene Schutz für den Verbraucher
bleibt von dieser Gewährleistung unberührt.

Leggere il manuale con attenzione e conservarlo per
eventuali riferimenti futuri. Se le informazioni contenute
in questo manuale risultassero poco chiare o se si desider-
asse approfondire alcuni aspetti relativi al computer Incite
non trattati nel testo, rivolgersi al rivenditore Trek oppure
contattare:
Trek Bicycle Corporation
Attn: Customer Service
801 W. Madison Street
Waterloo, Wisconsin 53594
http://www.trekbikes.com 920.478.4670

Non fissare a lungo il computer mentre si guida la
bicicletta (F1). È importante tenere gli occhi sulla
strada, per evitare eventuali ostacoli che potrebbero
causare la perdita di controllo del mezzo e possibili
cadute.


Sono presenti quattro pulsanti (F2):
A- Modalità
B- Impostazione
C- Scorrimento (due pulsanti: su e giù)
Esistono tre modalità di utilizzo dei pulsanti:
Push- premere una volta
Cycle – premere più volte a seconda della necessità
Hold- tenere premuto per due o tre secondi

OROLOGIO
CLK
TME
Orario del giorno, visualizzato in ore e minuti, o
cronometro che indica i secondi.
Formato 12 ore AM/PM o 24 ore
Lettura più alta: 23:59 (orologio) o 23:59:59
(cronometro)
CONTACHILOMETRI
ODO
La distanza percorsa viene indicata in miglia o in
chilometri.
TRP-Distanza percorsa (dall’ultimo riavvio)
TTL- Distanza totale dall’ultimo azzeramento
Lettura più alta: 99,999
VELOCITÁ Indica sempre la velocità corrente della bicicletta in
miglia orarie (MH) o in chilometri orari (KMH)
AVG- Velocità media dall’ultimo riavvio, indicata
in decimi.
MAX- Valore massimo dall’ultimo riavvio
Letture più alte: 80.5mph o 129.6kmh
ANDATURA Sempre visibile. Indica se la velocità corrente è
superiore o inferiore rispetto alla velocità media
La visualizzazione mostra una freccia rivolta
verso l’alto (velocità superiore alla media) o
verso il basso (velocità inferiore alla media)..
TEMPERATURA Sempre visibile
Indica la temperatura corrente in gradi interi
Fahrenheit o Celsius.
Lettura più bassa: -2° F +/-2°, -19° C +/-1°
Lettura più alta: 140° F +/-2°, 60° C +/-1°
SELEZIONE RUOTE Sempre visibile (F4)
Indica l’impostazione ruote utilizzata dal
computer
Ruota 1
INCITE
ACH
Ruota 2
INCITE
ACH

CADENZA Numero di giri/min del set di pedali
Indicato in numeri interi
Lettura più alta: 240.
AVG- Cadenza media dall’ultimo riavvio
MAX- Cadenza massima dall’ultimo riavvio
FREQUENZA
CARDIACA
HR
Frequenza cardiaca in battiti/min
CUR- Corrente
AVG- Frequenza cardiaca media dall’ultimo
riavvio
AVG- Frequenza cardiaca massima dall’ultimo
riavvio
ZONA- Le frecce indicano se la frequenza
cardiaca rientra nella zona di frequenza
preimpostata, oppure è ad essa superiore o
inferiore.
RETRO-
ILLUMINAZIONE
Fornisce una retroilluminazione al display per 5
secondi.
Per attivarla, tenere premuto il pulsante Mode..

Quando il computer è nuovo (o se avete sostituito le
batterie) deve essere programmato a seconda delle unità
da voi scelte e devono essere individuati i corretti segnali
sensori (velocità per il Link; anche la cadenza e la frequenza
cardiaca per il Link Team). Seguire le quattro fasi di
impostazione rapida, accoppiamento, connessione e riavvio.

1. Installare le batterie o premere il pulsante Reset (il pulsan-
tino argentato sul retro del computer, sotto il coperchio del
vano batteria) 4 Appaiono l’icona Ruota 1 e “700-23”.
2. Premere più volte il pulsante Scroll per cambiare dimensione
della ruota.
Selezionare la dimensione del pneumatico, usare la tabella (F7), o impostare una
dimensione della ruota personalizzata.
3. Premere il pulsante Set per selezionare 4 KMH o MPH
inizia a lampeggiare.
4. Premere più volte il pulsante Scroll per apportare modifiche.
5. Premere il pulsante Set per selezionare 4 o C° inizia a
lampeggiare.
6. Premere più volte il pulsante Scroll per apportare modifiche.
7. Premere il pulsante Set per selezionare 4 12 (orologio)
inizia a lampeggiare.
8. Premere più volte i pulsanti Scroll per l’orologio 12/24 ore.
9. Premere il pulsante Set per selezionare 4 Ora (A o P) inizia
a lampeggiare.
10. Premere più volte i pulsanti Scroll per modificare l’ora.
11. Premere il pulsante Set per selezionare 4 I minuti iniziano
a lampeggiare.
12. Premere più volte i pulsanti Scroll per modificare i minuti.
13. Premere il pulsante Set per selezionare 4 COPPIA DI
VELOCITÁ? inizia a lampeggiare.
14. Seguire le fasi in Accoppiamento”.

Il Link e il Link Team sono computer digitali a 2,4Ghz.
Ricevono trasmissioni codificate dai sensori per la velocità,
la cadenza e la frequenza cardiaca. Per poter ricevere queste
trasmissioni, il computer e il sensore devono riconoscersi
come Coppia. Una Coppia utilizza un codice univoco in
modo che gli altri sensori vicini non causino interferenze.
Ogni sensore (velocità, cadenza e Frequenza cardiaca)
invia un tipo specifico di segnale. In questo modo, il
computer riconoscerà soltanto i segnali provenienti da
quel tipo di sensore. Per fare un esempio, il computer
riconoscerà i dati sulla velocità solo se provenienti dal
relativo sensore.
Sono previste due modalità di procedura di accoppia-
mento: Fase 14 di “1. Impostazione rapida” o A Richiesta.
L’Impostazione rapida cancella tutti i dati del computer. La
procedura A Richiesta non cancella i dati. Per la configura-
zione iniziale, seguire l’Impostazione Rapida.

1. Posizionare il computer sulla bicicletta, o entro 3 piedi (1
metro) dal sensore.
2. Far emettere un segnale dal sensore (far girare la ruota della
bicicletta per la velocità, i pedali per la cadenza o indossare
la cinghia per il battito cardiaco per la frequenza cardiaca).
3. Tenere premuto il pulsante Set 4 PAIR... 4
LINK LINK TEAM
4 Appare la
velocità sullo
schermo.
Rilasciare il
pulsante.
4 CADENCE PAIR? viene visualiz-
zato.
4. Far emettere un segnale dal
sensore (far girare i pedali per la
cadenza).
5. Tenere premuto il pulsante Set 4
PAIR... 4 Appare la velocità sullo
schermo. Rilasciare il pulsante.

Se sostituite le batterie in un sensore o sull’unità princi-
pale, o cambiate sensori, utilizzate la procedura A Richiesta.
1. Posizionare il computer sulla bicicletta, o entro 3 piedi (1
metro) dal sensore.
2. Far emettere un segnale dal sensore (far girare la ruota della
bicicletta per la velocità, i pedali per la cadenza o indossare
la cinghia per il battito cardiaco per la frequenza cardiaca).
3. Premere entrambi i pulsanti Scroll 4 PAIR?
4. Tenere premuto il pulsante Set 4 PAIR... 4 vedere la
tabella in alto per il Link e il Link Team.

Quando fermate la bicicletta (o rimuovete la cinghia
per la frequenza cardiaca del Link Team) il sensore non
invia segnali. Quando il computer non riesce a trovare un
segnale, lo cerca.
Dopo cinque minuti di ricerca, il computer si disconnette
dai sensori, interrompe la ricerca ed entra in modalità di
attesa (Standby). In tal modo si risparmia la carica delle
batterie che viene utilizzata nella ricerca. Dopo 20 minuti di
inattività, il computer va in Sleep mode.
Dalla modalità di Standby o Sleep mode, per iniziare a
ricevere dati è necessario collegare il computer con ogni
sensore. Sono previste due modalità di connessione:

1. Inviare i segnali del sensore (muovere la ruota, azionare i
pedali, e/o indossare la cinghia per la frequenza cardiaca
entro il raggio d’azione).
2. Premere un pulsante qualsiasi.
Il computer si collegherà automaticamente a ogni sensore. L’operazione richiederà
alcuni secondi. Se il computer non trova un segnale, dopo 20 secondi passerà al sensore
successivo secondo l’ordine: velocità, cadenza, Frequenza cardiaca.
Se il computer non riesce a collegarsi a un sensore qualsiasi, lo schermo visualizzerà “-
-”. Seguire le istruzioni “Connessione da Standby,” o vedere Risoluzione dei problemi.

1. Far emettere segnali dai sensori (muovere la ruota, azionare
i pedali, e/o indossare la cinghia per la frequenza cardiaca
entro il raggio d’azione).
2. Tenere premuto il pulsante Set e il pulsante Mode 4 ”0”
inizia a lampeggiare 4 ”0” appare senza lampeggiare 4
viene visualizzato il valore.
3. Rilasciare i pulsanti.
Se appare --- , verificare la distanza fra il computer e il sensore, e fra il sensore e il
magnete. Se il computer ancora non si collega, seguire le fasi per l’Accoppiamento del
computer o consultare Risoluzione dei problemi.

Il computer registra due serie di dati: I dati totali dal
momento in cui è stato installato e i dati relativi al viaggio
a partire dall’ultimo Riavvio (i dati relativi alla Frequenza
cardiaca sono disposti a parte – vedere la sezione Frequenza
cardiaca):
• CONTACHILOMETRI TRP
• VELOCITÁ MEDIA, MASSIMA
• CADENZA MEDIA, MASSIMA
• OROLOGIO (Cronometro)

1. Premere più volte il pulsante Mode per impostare l’orologio.
2. Premere più volte i pulsanti Scroll per impostare il
cronometro.
3. Tenere premuto il pulsante Set e il pulsante Mode.
L’impostazione del cronometro mostra ‘00:00.00’ a indicare che la modalità di viaggio
è azzerata.
4. Rilasciare i pulsanti.

Il computer può raccogliere dati relativi a due diverse
dimensioni delle ruote. Vedere “Utilizzo delle caratteris-
tiche, velocità”. Queste istruzioni spiegano come passare a
un’altra dimensione della ruota.
1. Premere più volte il pulsante Mode per impostare
CONTACHILOMETRI.
2. Premere il pulsante Scroll sinistro e destro 4 l’icona della
ruota cambia.



La velocità corrente è sempre visibile.
1. Premere più volte il pulsante Mode o il pulsante Set per
impostare VELOCITÁ.
2. Premere più volte i pulsanti Scroll per impostare AVG e MAX.
• AVG – velocità media
• Il frequenziometro indica se la velocità attuale è
superiore o inferiore alla media.
• MAX- velocità massima
 4
Tenere premuto il pulsante Mode e il pulsante Set 4 per
azzerare a 000.

1. Premere più volte il pulsante Mode o il pulsante Set per
impostare VELOCITÁ.
2. Tenere premuto il pulsante Set 4 Appare l’icona della ruota.
3. Premere più volte il pulsante Set 4 Ruota 1 o Ruota 2.
4. Premere il pulsante Scroll per selezionare.
5. Premere più volte il pulsante Scroll per scegliere la
dimensione voluta.

Lees deze handleiding zorgvuldig door en bewaar
deze ter referentie. Als je de informatie in deze
handleiding niet begrijpt of als je vragen hebt over je
Incite-computer die niet in deze handleiding worden
beantwoord, neem je contact op met je Trek-dealer of
schrijf je naar:
Trek Bicycle Corporation
T.a.v: Customer Service
801 W. Madison Street
Waterloo, Wisconsin 53594 USA
http://www.trekbikes.com +001 920.478.4670

Kijk tijdens het fietsen niet langdurig naar de
computer (F1). Als je niet naar de weg kijkt, loop
je het risico een obstakel te raken, waardoor je de
controle over de fiets zou kunnen verliezen en zou
kunnen vallen.


De computer is voorzien van vier knoppen (F2):
A - Mode
B - Set
C - Scroll (twee knoppen: omhoog en omlaag)
De knoppen kunnen op drie manieren worden
gebruikt:
Drukken: één keer drukken.
Bladeren: meerdere keren drukken totdat de gewenste
functie of waarde wordt weergegeven.
Ingedrukt houden: twee of drie seconden ingedrukt
houden.

CLOCK
CLK
TME
Tijdstip weergegeven in uren en minuten. Voor
de rittijd worden ook seconden weergeven.
12 uursnotatie met AM/PM-aanduiding of 24
uursnotatie.
Hoogste waarde: 23:59 (klok) of 23:59:59
(rittijd)
ODOMETER
ODO
Afgelegde afstand in mijlen of kilometers.
TRP: trip (sinds laatste herstart).
TTL: totaal sinds laatste Reset.
Hoogste meetwaarde: 99,999
SPEED Geeft altijd de huidige snelheid van de fiets
weer in mijl per uur (MH) of kilometer per
uur (KMH).
AVG: gemiddelde snelheid sinds laatste her-
start, afgerond op één decimaal.
MAX: hoogste waarde sinds laatste herstart.
Hoogste meetwaarde: 80.5mph of
129.6kph
PACER Wordt altijd weergegeven. Geeft aan of de
huidige snelheid boven of onder de gemiddelde
snelheid ligt.
Er wordt een pijl-omhoog (sneller) of pijl-
omlaag (langzamer) weergegeven..
TEMPERATURE Wordt altijd weergegeven.
De huidige temperatuur in hele graden
Fahrenheit of Celsius.
Laagste meetwaarde: -2° F +/-2°, -19°
C +/-1°
Hoogste meetwaarde: 140° F +/-2°,
60° C +/-1°
WHEEL
SELECTION
Wordt altijd weergegeven (F4).
De wielmaat die door de computer wordt
gebruikt.
Wheel 1
INCITE
ACH
Wheel 2
INCITE
ACH

CADENCE Het aantal trapasomwentelingen per minuut.
Weergave in hele getallen.
Hoogste meetwaarde: 240.
AVG: gemiddelde cadans sinds laatste
herstart.
MAX: maximum cadans sinds laatste
herstart
HEART RATE
HR
Aantal hartslagen per minuut
CUR: de huidige waarde.
AVG: de gemiddelde hartslag sinds laatste
herstart.
MAX: maximum hartslag sinds laatste
herstart.
ZONE: aan de hand van pijlen wordt aange-
geven of de hartslag in, beneden of boven
de ingestelde zone ligt.
BACKLIGHT Vijf seconden achtergrondverlichting.
Als je de achtergrondverlichting wilt acti-
veren, houd je de knop Mode ingedrukt.

Als de computer nieuw is (of als de batterij is
vervangen), moeten de gewenste eenheden en de
juiste signalen (snelheid voor Link; voor de Link
Team tevens de cadans en hartslag) worden ingesteld.
Volg de vier stappen Snel instellen, Paren, Verbinding
maken en Herstarten.

1. Plaats de batterij of druk op de resetknop (de kleine
zilverkleurige knop aan de achterzijde van de computer
onder de batterijdeksel) 4 Wheel 1 en ‘700-23’ worden
weergegeven.
2. Blader met de Scroll-knop om de wielmaat te wijzigen.
Selecteer de bandmaat, gebruik hiervoor de tabel (F7), of geef een aangepaste
wielmaat op.
3. Druk op de knop Set om de maat in te stellen. 4 KMH
of MPH begint te knipperen.
4. Blader met de Scroll-knoppen om een andere optie te
selecteren.
5. Druk op de knop Set om de optie in te stellen 4 F° of
C° begint te knipperen.
6. Druk op de Scroll-knoppen om een andere optie weer
te geven.
7. Druk op de knop Set om de gewenste optie in te
stellen.___De 12 (uursnotatie) begint te knipperen.
8. Gebruik de Scroll-knoppen om 12 of 24 te weer te
geven.
9. Druk op de knop Set om de gewenste optie in te
stellen. 4 De uurweergave begint te knipperen (A of
P)
10. Gebruik de Scroll-knoppen de uren te wijzigen.
11. Druk op de knop Set om de uren in te stellen. 4 De
minuutweergave begint te knipperen.
12. Gebruik de Scroll-knoppen de minuten te wijzigen.
13. Druk op de knop Set om de minuten in te stellen 4
SPEED PAIR? begint te knipperen.
14. Volg de stappen in ‘Paren’.

De Link en Link Team zijn digitale computers met
een snelheid van 2,4 Ghz. Ze ontvangen gecodeerde
gegevens van de sensoren voor de snelheid, cadans
en hartslag. Voordat de computer deze gegevens kan
ontvangen, moeten de sensor en de computer elkaar
herkennen als een paar. Een paar gebruikt een unieke
code zodat de sensoren in de nabije omgeving geen
interferentie veroorzaken.
Elke sensor (snelheid, cadans en hartslag) verzendt
een specifiek type signaal. In een bepaalde modus
herkent de computer alleen het signaal van de
bijbehorende sensor. De computer verwerkt bijvoor-
beeld alleen de snelheidsgegevens van de bijbehorende
snelheidsensor.
De sensoren en de computer kunnen op twee
manieren worden gepaard: Stap 14 van ‘1. Snel
instellen’ of tussentijds verzoek. Tijdens de procedure
Snel instellen worden alle computergegevens gewist.
Als je de computer tussentijds instelt, worden er geen
gegevens gewist. Als je de computer voor de eerste
keer instelt, volg je de procedure Snel instellen.

1. Plaats de computer op de fiets of binnen 1 meter (3
voet) van de sensor.
2. Zorg dat de sensor een signaal verzendt (draai het wiel
voor de snelheid, de trapas voor de cadans of draag de
hartslagband voor de hartslag).
3. Houd de knop Set ingedrukt. 4 PAIR... 4
LINK LINK TEAM
4 Het
scherm
Speed
verschijnt.
Laat de
knop los.
4 CADENCE PAIR? verschijnt.
4. Zorg dat de sensor een
signaal verzendt (draai de
trapas voor de cadans).
5. Houd de knop Set ingedrukt.
4 PAIR... 4 Het scherm
Speed verschijnt. Laat de
knop los.

Als je de batterij in een sensor of de computer
vervangt of sensoren verwisselt, gebruik je de tussen-
tijdse paringsprocure.
1. Plaats de computer op de fiets of binnen 1 meter (3
voet) van de sensor.
2. Zorg dat de sensor een signaal verzendt (draai het wiel
voor de snelheid, de trapas voor de cadans of draag de
borstband voor de hartslag).
3. Druk tegelijkertijd op beide Scroll-knoppen. 4 PAIR?
4. Houd de knop Set ingedrukt 4 PAIR... 4 Zie de
bovenstaande tabel voor de Link en Link Team.

Als je stilstaat (of wanneer je de borstband voor
de Link Team niet draagt), worden er geen sensor-
signalen verzonden. Wanneer er geen signaal wordt
gevonden, gaat de computer op zoek naar een signaal.
Na vijf minuten zoeken, wordt de verbinding met de
sensor(en) verbroken en stopt computer met zoeken.
De computer schakelt naar de stand-bymodus. Dit
bespaart batterijen omdat het zoeken energie van de
batterijen vergt. Na 20 minuten inactiviteit schakelt
de computer naar de slaapstand.
Wanneer de computer stand-by of in de slaapstand
staat, moet je de computer met de sensor(en)
verbinden voordat je gegevens kunt ontvangen. Je
kunt op twee manieren verbinding maken:

1. Zorg dat er sensorsignalen worden verzonden (draai
het wiel, de trapas en/of draag de borstband binnen het
bereik van de computer).
2. Druk op een knop.
De computer maakt automatisch verbinding met de sensoren. Dit kan enkele
seconden duren. Als de computer na 20 seconden nog geen signaal heeft
gevonden, wordt op volgorde naar de volgende sensor gezocht: snelheid,
cadans, hartslag.
Als de computer met geen enkele sensor verbinding kan maken, wordt ‘- -’
weergegeven. Volg de instructies in het gedeelte ‘Verbinding maken vanuit de
stand-bymodus’ of zie het gedeelte ‘Problemen oplossen’.

1. Zorg dat er sensorsignalen worden verzonden (draai
het wiel, de trapas en/of draag de borstband binnen het
bereik van de computer).
2. Houd de knoppen Set en Mode ingedrukt. 4 ’0’ begint
te knipperen. 4 ’0’ knippert niet meer. 4 De waarde
wordt weergegeven.
3. Laat de knoppen los.
Als --- wordt weergegeven, controleer je de afstand van de computer tot de
sensor en van de sensor tot de magneet. Als de computer nog steeds geen
verbinding kan maken, volg je de stappen in het gedeelte ‘Paren’ of zie het
gedeelte ‘Problemen oplossen’.

Je computer registreert twee sets gegevens: de
totalen vanaf het moment dat de computer is ingesteld
en de ritgegevens vanaf de laatste herstart (de
hartslaggegevens worden afzonderlijk verwerkt, zie
het gedeelte Hartslag):
• ODOMETER TRP
• SPEED AVG, MAX
• SPEED AVG, MAX
• CLOCK (Ride Time)

1. Blader met de knop Mode naar CLOCK.
2. Blader met de Scroll-knoppen naar Ride Time.
3. Houd de knoppen Set en Mode ingedrukt.
De instelling voor Ride Time is ‘00:00.00’. Dit betekent dat de tripmodus op
nul is gesteld.
4. Laat de knoppen los.

De computer kan gegevens bewaren voor twee
wielmaten. Zie ‘De functies gebruiken, Snelheid’.
Aan de hand van deze instructies kun je de andere
wielmaat wijzigen.
1. Blader met de knop Mode naar ODOMETER.
2. Druk op de linker en rechter Scroll-knop. 4 Het
wielpictogram wordt gewijzigd.



De huidige snelheid wordt altijd weergegeven.
1. Blader met de knop Mode of Set naar SPEED.
2. Blader met de Scroll-knoppen naar AVG en MAX.
• AVG: gemiddelde snelheid
• Aan de hand van een pijl wordt aangegeven of
de huidige snelheid boven of onder de gemiddelde
snelheid ligt.
• MAX: maximum snelheid
 4
Houd de knoppen Mode en Set ingedrukt. 4 De waarde
wordt ingesteld op 0.00.

1. Blader met de knop Mode of Set naar SPEED.
2. Houd de knop Set ingedrukt. 4 Het wielpictogram
verschijnt.
3. Blader met de knop Set. 4 Wheel 1 of Wheel 2 wordt
weergegeven.
4. Druk op de knop Scroll om de gewenste optie te
selecteren.
5. Blader met de Scroll-knoppen naar de gewenste
wielmaat.
MENU VOOR
WIELMAAT AANGEPASTE WIELMAAT
6. Druk op
de knop
Scroll om
de geselect-
eerde
wielmaat in
te stellen.
7. Druk op
de knop
Mode. 4
Het scherm
Speed wordt
weerge-
geven..
6. Bepaal de omtrek van het
wiel (F8).
7. Blader met de knop Scroll
naar het viercijferige getal.
8. Houd de knop Set
ingedrukt.___Het eerste
cijfer begint te knipperen.
9. Blader met de Scroll-
knoppen naar de gewenste
waarde.
10. Druk op de knop Set om
de waarde in te stellen. 4
_Het volgende getal begint
te knipperen.
11. Herhaal step 9 en 10 voor
de overige cijfers.
12. Druk op de knop Mode. 4
Het scherm SPD verschijnt..
Herhaal de stappen om de andere wielmaat in te stellen, maar kies bij stap 3 het
andere wiel.


1. Blader met de knop Mode of Set naar CLOCK.
2. Blader met de Scroll-knoppen naar Clock (00:00P) of
Ride Time (00:00:00).

1. Blader met de knop Mode of Set naar CLOCK.
2. Houd de knop Set ingedrukt 4 12 (uursnotatie) begint
te knipperen.
3. Blader met de Scroll-knoppen naar 12 of 24.
4. Druk op de knop Set om de optie te selecteren. 4 De
uurweergave begint te knipperen (A of P)
5. Blader met de Scroll-knoppen om de uren op te geven.
6. Druk op de knop Set om de uren in te stellen. 4 De
minuutweergave begint te knipperen.
7. Blader met de Scroll-knoppen om de minuten op te
geven.
8. Druk op de knop Set om de gewenste waarde in te
stellen 4 Het scherm Clock wordt weergegeven.


1. Blader met de knop Mode of Set naar ODOMETER.
2. Blader met de Scroll-knoppen om TRP en TTL weer te
geven.

1. Blader met de knop Mode of Set naar ODOMETER.
2. Blader met de Scroll-knoppen naar TTL.
3. Houd de knop Set ingedrukt. 4 Het eerste cijfer
begint te knipperen.
4. Blader met de Scroll-knoppen naar het gewenste cijfer.
5. Druk op de knop Set om de waarde in te stellen. 4
Het volgende cijfer begint te knipperen.
6. Herhaal stap 4 en 5 totdat je alle cijfers hebt ingesteld.
4 Het scherm TTL wordt weergegeven.


1. Blader met de knop Mode of Set naar ODOMETER.
2. Blader met de Scroll-knoppen naar TRP.
3. Houd de knop Set ingedrukt 4 MPH begint te
knipperen.
4. Blader met de Scroll-knoppen naar KMH of MPH.
5. Druk op de knop Set om de gewenste optie in te stellen
4 F° begint te knipperen.
6. Blader met de Scroll-knoppen naar F° of C° en kies stap
7 voor het betreffende model computer:
LINK LINK TEAM
7. Druk op de
knop Set om
de gewenste
optie in te
stellen. 4
Het scherm
TRP wordt
weerge-
geven.
7. Druk op de knop Set om de
gewenste optie in te stellen
4 CAd (cadans) wordt
weergegeven. De optie OFF
of ON begint te knipperen.
8. Blader met de Scroll-
knoppen naar OFF of ON.
9. Druk op de knop Set_ om de
gewenste optie te selecteren
4 CAd (cadans) wordt
weergegeven. De optie OFF
of ON begint te knipperen.
10. Blader met de Scroll-
knoppen naar OFF of ON.
11. Druk op de knop Set om
de gewenste optie selecteren
4 Het scherm TRP wordt
weergegeven.

Met de Link Team-computer kan tevens de cadans
(CAd) of hartslag (Hr) worden weergegeven. Als je
een van deze functies of beide functies wilt gebruiken,
moet je de functie instellen op ON (zie ‘Eenheden en
meetwaarden’ hierboven).
Als een functie niet is ingeschakeld (OFF), zal de
computer geen paarprocedure uitvoeren en wordt er
geen verbinding met de sensor gemaakt.

Als je de cadans wilt weergeven, moet je de functie
CADENCE instellen op ON (zie ‘Eenheden en
meetwaarden’ hierboven).

1. Blader met de knop Mode naar Cadence.
2. Blader met de Scroll-knoppen naar CUR, AVG of MAX.

1. Blader met de knop Mode naar Cadence.
2. Houd de knoppen Mode en Set ingedrukt. 4 De
waarde wordt ingesteld op 000.

Als je de hartslagfunctie wilt gebruiken, moet
je de optionele borstband voor de hartslagmeting
aanschaffen. Daarnaast moet je de hartslagfunctie
instellen op ON (zie ‘Eenheden en meetwaarden’
hierboven).

1. Blader met de knop Mode of Set naar Heart Rate.
2. Blader met de Scroll-knoppen naar CUR, AVG, MAX of
ZONE.

1. Blader met de knop Mode naar HEART RATE.
2. Houd de knoppen Mode en Set ingedrukt. 4 De
waarde wordt ingesteld op 000.

1. Blader met de knop Mode naar Heart Rate.
2. Blader met de Scroll-knoppen naar ZONE.
a. De tijd in de zone wordt weergegeven.
a. De tijd beneden de zone wordt weergegeven.
a. De tijd boven de zone wordt weergegeven.

1. Blader met de knop Mode naar Heart Rate.
2. Houd de knop Set ingedrukt. 4 SET ZONE verschijnt.
4 Het eerste cijfer van de bovenlimiet begint te
knipperen.
3. Blader met de Scroll-knoppen om het cijfer te wijzigen.
4. Druk op de knop Set om de gewenste in te stellen. 4
Het tweede cijfer begint te knipperen.
5. Blader met de Scroll-knoppen om het cijfer te wijzigen.
6. Druk op de knop Set om de gewenste in te stellen. 4
Het derde cijfer begint te knipperen.
7. Druk op de knop Set om de gewenste waarde in te
stellen. 4 De onderlimiet begint te knipperen.
8. Herhaal stap 3 tot en met 7 om de onderlimiet in te
stellen. 4 Het scherm Zone wordt weergegeven.


Druk stevig op de computer (niet de houder) en
schuif de computer schuin naar beneden (F3).

Leeg
scherm
Computer bevindt zich in transportmodus. Druk
op een knop.
Batterij is leeg of onjuist geplaatst. Plaats een
goede batterij
Foutieve
gegevens
Magneet niet goed uitgelijnd of afstand te groot.
Stel de plaatsing van de magneet en de sensor bij
Batterij is bijna leeg. Vervang de batterij.
Geen
huidige
snelheid
Magneet niet goed uitgelijnd of afstand te groot.
Stel de plaatsing van de magneet en de sensor bij.
Onjuiste
snelheid
Onjuiste wielmaat. Stel de computer opnieuw in..
Sensor leest de magneet niet goed. Stel de uitlijning
van de magneet en de sensor bij..
Geen cadans Sensor leest de magneet niet goed. Stel de uitlijning
van de magneet en de sensor bij..
De contactpunten van de computer en de houder
maken geen contact, omdat de computer niet
(goed) in de houder is geplaatst. Plaats de computer
(opnieuw) in de houder.
Geen hart-
slag
De batterij van de borstband is bijna leeg. Vervang
de batterij..
De borstband maakt geen contact met de huid.
Maak de borstband vochtig en verplaats de band..
Pair-fout Zorg dat de afstand tussen de computer en de sen-
sor niet meer dan 1 meter (3 voet) bedraagt.
Controleer de batterij van de sensor.

Wanneer de computer onjuiste gegevens weergeeft,
is de batterij mogelijk bijna leeg. Vervang de batterijen
wanneer de computer niet goed werkt of vervang
de batterij elke zes maanden. Wanneer je nieuwe
batterijen koopt, kun je de oude batterijen het beste
meenemen naar de winkel.
CR2032, lithiumbatterij, 3 volt
Wanneer je de batterij verwijdert, worden de
totaalwaarden voor de functies automatisch gereset
(teruggezet naar nul). Als je de totalen noteert voordat
je de batterij verwijdert, kun je de totalen naderhand
handmatig instellen.

1. Haal de computer uit de houder.
2. De batterijdekseltje bevindt zich aan de onderzijde van
de computer.
3. Draai het dekseltje klep ongeveer een kwartslag tegen
de klok in (F5).
4. Verwijder het dekseltje om toegang te verkrijgen tot
de batterij.
Let goed op dat je de rubberen afsluitring niet laat vallen.
5. Verwijder de oude batterij.
6. Plaats de nieuwe batterij met het plusteken (+) en het
opschrift naar boven (F6).
7. Plaats het batterijdekseltje (en de afsluiting) terug en
draai het een kwartslag rechtsom.

Trek Bicycle Corporation garandeert elke nieuwe
Incite computer tegen defecten in vakmanschap en
materialen.
Deze garantie dekt Trek Incite computer modellen 6i,
8i, 9i, 11i, ACH, en ACH Digital voor een periode van
twee jaar vanaf de verkoopdatum.
Deze garantie dekt geen Normale slijtage, inclusief
de duurzaamheid van de batterij
• Onjuiste montage
• Installatie van onderdelen of accessoiries die niet
orgineel bedoeld zijn, of verenigbaar zijn met het
onderdeel als die verkocht is
• Schade of defecten als gevolg van ongelukken,
verkeerd gebruik, misbruik, of verwaarlozing
Deze garantie wordt in zijn geheel ongeldig door elke
aanpassing van de componenten of zijn onderdelen.
Deze garantie is uitdrukkelijk beperkt tot de
reparatie of vervanging van een defect onderdeel
en is het enige middel van garantie. Deze garantie
gaat in vanaf de datum van aankoop, en is alleen
van toepassing op de originele eigenaar, en kan niet
worden overgedragen. Trek is niet verantwoordelijk
voor incidentele of consequentiele schade. Sommige
staten/landen staan de uitsluiting van incidentele of
voortvloeiende schade niet toe, dus de bovengenoemde
uitsluiting is mogelijk niet van toepassing op u.
Eisen onder deze garantie moeten worden gemaak
door een geautoriseerde dealer. Aankoopbewijs is
vereist.
Deze garantie heeft de gebruiker specifieke legale
rechten, en deze kunnen van plaats tot plaats varieren.
Deze garantie beinvloedt niet de statutaire rechten
van de klant.
MENU
DIMENSIONE
RUOTE
DIAMETRO RUOTE
PERSONALIZZATO
6. Premere il
pulsante Set
per selezi-
onare.
7. Premere il
pulsante
Mode___
Appare la
velocità sullo
schermo
6. Determinare la circonferenza della
ruota (F8)
7. Premere più volte il pulsante Scroll
per impostare un numero a 4 cifre.
8. Tenere premuto il pulsante Set__la
prima cifra inizia a lampeggiare
9. Premere più volte il pulsante Scroll
per ottenere il valore desiderato
10. Premere il pulsante Set per selezi-
onare __la cifra successiva inizia a
lampeggiare
11. Ripetere le fasi 9 e 10 per le altre
cifre
12. Premere il pulsante Mode___SPD
appare sullo schermo
Per impostare un’altra Dimensione della ruota, ripetere le varie fasi, ma alla fase 3 scegliere
un’altra ruota.


1. Premere più volte il pulsante Mode o il pulsante Set per
impostare l’orologio.
2. Tenere premuti i pulsanti Scroll per impostare l’Orologio
(00:00P) o il cronometro (00:00:00).

1. Premere più volte il pulsante Mode o il pulsante Set per
impostare l’orologio.
2. Premere il pulsante Set 4 12 (orologio) inizia a lampeggiare.
3. Premere più volte i pulsanti Scroll per impostare 12 o 24.
4. Premere il pulsante Set per selezionare 4 L’ Ora (A o P) inizia
a lampeggiare.
5. Premere più volte i pulsanti Scroll per impostare l’Ora.
6. Premere il pulsante Set per selezionare 4 I minuti iniziano a
lampeggiare.
7. Premere più volte i pulsanti Scroll per impostare i Minuti.
8. Premere il pulsante Set per selezionare 4 L’orologio appare
sullo schermo.


1. Premere più volte il pulsante Mode o il pulsante Set per
impostare il contachilometri.
2. Premere più volte i pulsanti Scroll per impostare TRP e TTL.

1. Premere più volte il pulsante Mode o il pulsante Set per
impostare il contachilometri.
2. Premere più volte i pulsanti Scroll per impostare TTL.
3. Tenere premuto il pulsante Set 4 La prima cifra inizia a
lampeggiare
4. Premere più volte i pulsanti Scroll per impostare il numero
stabilito.
5. Premere il pulsante Set per selezionare 4 la cifra successiva
inizia a lampeggiare
6. Ripetere la Fase 4 e la 5 fino a completare la selezione di tutte
le cifre 4 TTL appare sullo schermo.


1. Premere più volte il pulsante Mode o il pulsante Set per
impostare il contachilometri.
2. Premere più volte i pulsanti Scroll per impostare TRP.
3. Tenere premuto il pulsante Set 4 MPH inizia a lampeggiare
4. Tenere premuti i pulsanti Scroll per impostare KMH o MPH.
5. Premere il pulsante Set per selezionare 4 inizia a lampeg-
giare.
6. Tenere premuti i pulsanti Scroll per impostare F° o e
scegliere la Fase 7 per il vostro modello di computer:
LINK LINK TEAM
7. Premere il
pulsante
Set per
selezionare
4 TRP
appare sullo
schermo..
7. Premere il pulsante Set per selezi-
onare 4 CAd (cadenza) appare con
OFF o ON lampeggianti.
8. Tenere premuti i pulsanti Scroll per
impostare OFF o ON.
9. Premere il pulsante Set per selezi-
onare 4 Hr (frequenza cardiaca)
appare con OFF o ON lampeggianti.
10. Tenere premuti i pulsanti Scroll
per impostare OFF o ON.
11. Premere il pulsante Set per
selezionare 4 TRP appare sullo
schermo..

Il vostro computer Link Team può visualizzare cadenza
(CAd) o Frequenza cardiaca (Hr). Per utilizzare una o
entrambe queste funzioni, è necessario impostare la funzione
su ON (vedere sopra “Unità e Misura”).
Se una funzione viene impostata su OFF, il computer non
cercherà di accoppiarsi o collegarsi con quel sensore.

Per utilizzare questa funzione, è necessario impostare la
funzione CADENZA su ON (vedere sopra “Unita e Misura”).

1. Premere più volte il pulsante Mode per impostare la cadenza.
2. Premere più volte i pulsanti Scroll per impostare CUR, AVG
o MAX.

1. Premere più volte il pulsante Mode per impostare la cadenza.
2. Tenere premuto il pulsante Mode e il pulsante Set 4 per
azzerare a 000.

Per utilizzare questa funzione, acquistare dal vostro
fornitore la cinghia facoltativa per la frequenza cardiaca.
Inoltre, è necessario impostare la funzione di frequenza
cardiaca su ON (vedere sopra “Unità e Misura”).

1. Premere più volte il pulsante Mode o il pulsante Set per
impostare la frequenza cardiaca.
2. Premere più volte i pulsanti Scroll per impostare CUR, AVG,
MAX o ZONE.

1. Premere più volte il pulsante Mode per impostare
FREQUENZA CARDIACA.
2. Tenere premuto il pulsante Mode e il pulsante Set 4 per
azzerare a 000.

1. Premere più volte il pulsante Mode per impostare la frequenza
cardiaca.
2. Premere più volte i pulsanti Scroll per impostare ZONA.
a. Appare la frequenza che rientra nella zona preimpostata.
b. Appare la frequenza superiore alla zona preimpostata.
c. Appare la frequenza inferiore alla zona preimpostata.

1. Premere più volte il pulsante Mode per impostare la frequenza
cardiaca.
2. Tenere premuto il pulsante Set 4 Appare SET ZONE _la
prima cifra del Limite superiore inizia a lampeggiare
3. Premere più volte i pulsanti Scroll per modificare il numero.
4. Premere il pulsante Set per selezionare 4 la seconda cifra
inizia a lampeggiare
5. Premere più volte i pulsanti Scroll per modificare il numero.
6. Premere il pulsante Set per selezionare 4 la terza cifra inizia
a lampeggiare
7. Premere il pulsante Set per selezionare 4 Limite inferiore
inizia a lampeggiare
8. Ripetere le fasi da 3 a 7 per selezionare il limite inferioret 4
Zone appare sullo schermo.


Premere con decisione il computer (non la base) all’indietro
(F3).

Lo schermo
è vuoto
Il computer è nella modalità di trasporto. Premere un pul-
sante.
La batteria è scarica oppure è stata installata in modo non
corretto. Reinstallare una batteria carica..
I dati non
sono affid-
abili
Il magnete è male allineato oppure è troppo distante.
Riposizionare il magnete e il sensore.
La batteria si sta scaricando. Sostituire la batteria.
Non viene
indicata la
velocità cor-
rente
Il magnete è male allineato oppure è troppo distante.
Riposizionare il magnete e il sensore..
La velocità
non è cor-
retta
Il diametro ruote non è corretto. Azzerare il computer.
Il sensore non legge correttamente i dati del magnete.
Riallineare il magnete e il sensore
Non viene
indicata la
cadenza
Il magnete non legge correttamente i dati del sensore.
Riallineare il magnete e il sensore..
I contatti fra il computer e la base non sono presenti perché il
computer non è sulla base. Reinstallare.
Non viene
indicata la
frequenza
cardiaca
La batteria della cinghia per la frequenza cardiaca si sta
scaricando. Sostituire la batteria..
La cinghia per la frequenza cardiaca non è a contatto con la
pelle. Inumidire e riposizionare..
“Errore” di
accoppia-
mento
Assicurarsi che la distanza fra il computer e il sensore non
superi i 3 piedi (1 metro))
Controllare la batteria del sensore

Se il computer sta fornendo informazioni errate, la batteria
si sta scaricando. Sostituire le batterie ogni volta che si rileva
un malfunzionamento del computer, oppure ogni sei mesi.
Quando si devono acquistare nuove batterie, si consiglia di
portare con le vecchie batterie.
CR2032, celle di litio, 3 volt
Quando viene rimossa la batteria, il computer riporta
automaticamente i totali delle funzioni a zero. Dopo aver
inserito una nuova batteria, è possibile impostare manual-
mente i totali, ma si consiglia di prenderne nota prima di
rimuovere la batteria scarica.

1. Estrarre il computer dalla base.
2. Individuare il coperchio del vano batteria.
3. Ruotare in senso orario per un quarto di giro (F5).
4. Sollevare il coperchio per esporre la batteria.
Fare attenzione a non perdere la guarnizione ad anello di gomma.
5. Estrarre la vecchia batteria.
6. Inserire la nuova batteria con la “croce” e l’etichetta identifica-
tiva rivolte verso l’alto (figura F6).
7. Riposizionare il coperchio del vano batteria (ricordarsi di
inserire la guarnizione ad anello) e ruotare in senso orario per
un quarto di giro.

La Trek Bicycle Corporation garantisce ciascun nuovo
computer Incite contro difetti di fabbricazione e dei materiali:
Questa garanzia copre i modelli 6i, 8i, 9i, 11i, ACH, e ACH
Digital dei computer della Trek Incite per un periodo di due
anni dalla data di vendita.
Questa garanzia non copre le normali usura e rotture,
incluso la lunghezza del periodo di vita della batteria
• Assemblaggio non adeguato
• Installazione di parti o accessori non originariamente
progettati per, o compatibili con la bicicletta così come viene
venduta
• Danni o malfunzionamenti a causa di incidente, uso
scorretto, abuso o negligenza
La presente garanzia si intende totalmente nulla in caso di
modificazioni al Trailster o ai suoi componenti.
La presente garanzia è espressamente limitata alla ripara-
zione o alla sostituzione di un articolo difettoso ed è il solo
risarcimento previsto dalla garanzia. La presente garanzia
vale a partire dalla data di acquisto, è applicabile solo al
proprietario originale e non è trasferibile. Trek non è respon-
sabile per danni incidentali o consequenziali. Alcuni stati non
permettono l’esclusione di danni accidentali o conseguenti,
pertanto l’esclusione suddetta potrebbe non interessarvi.
Le richieste coperte da tale garanzia devono essere presen-
tate presso il rivenditore autorizzato. E’ necessario presentare
una prova di acquisto.
La presente garanzia dà al consumatore diritti legali
specifici, e tali diritti possono variare da luogo a luogo. La
presente garanzia non ha effetto sui diritti stabiliti dalla
legge per il consumatore
Japanese
このマニュアルは、よくお読みになったうえで、今後
の参考のために保管しておいてください。このマニュア
ルの内容を理解できない場合、または、購入されたイン
サイトコンピューターに関して、このマニュアルに記載
されていない内容についてご質問がある場合は、トレッ
ク販売店または下記までご連絡ください。
Trek Bicycle Corporation
Attn: Customer Service
801 W. Madison Street
Waterloo, Wisconsin 53594 USA
http://www.trekbikes.com 920.478.4670
安全性に関する情報と一般的なガイドライン
走行中は、長時間にわたりコンピューターを覗き
こまないようにしてください(図F1)。道路から
目を離すと、障害物にぶつかってコントロールを失
い、転倒する危険性があります。
機能
ボタンの使用方法
このコンピューターには4つのボタンがあります(
図F2)。
A―モード
B―セット
C―スクロール(アップとダウンの2つのボタン)
以下の3種類の方法でボタンを操作します。
押す―1回押す
連続して押す―必要に応じて何回か連続して押す
長押しする―2~3秒間押し続けたあと放す
モード
時計
CLK
TME
時刻を時分で表示。走行時間の
場合は秒も表示。
12時間表示(AM/PM付き)、
または24時間表示。
表示最高値:23:59(時計)ま
たは23:59:59(走行時間)
オドメ
ーター
ODO
走行距離をマイルまたはキロメ
ートルで表示。
TRP―トリップメーター(
前回のリスタート以降の走行
距離)
TTL―前回のリセット以降の
積算距離
表示最高値:99,999
速度 現在の車速をマイル(MH)ま
たはキロメートル(KMH)で常
時表示。
AVG―前回リスタートして以
降の平均速度を小数点第1位ま
で表示。
MAX―前回リスタートして以
降の最高速度を表示。
表示最高値:80.5MHまたは
129.6KMH
ペー
スメー
カー
常時表示。現在の速度が平均速
度よりも速いか遅いかを表示。
上向き矢印(速い)または下向
き矢印(遅い)で表示。
気温 常時表示。
現在の気温を華氏または摂氏で
整数表示。
表示最低値:-2°F±2°、-
19°C±1°
表示最高値:140°F±2°、
60°C±1°
ホイー
ル選択
常時表示(図F4)。
コンピューターがどのホイール
設定を使用しているかを表示。
ホイール1
INCITE
ACH
ホイール2
INCITE
ACH
LinkTeamのみ
ケイデ
ンス
クランクセットの回転数(
毎分)
整数表示
表示最高値:240
AVG―前回リスタートして以
降の平均ケイデンス
MAX―前回リスタートして以
降の最高ケイデンス
心拍数
HR
1分あたりの心臓の鼓動数
CUR―現在値
AVG―前回リセットして以降
の平均心拍数
MAX―前回リセットして以降
の最高心拍数
ZONE―現在の心拍数が、設
定範囲内か、設定範囲を上回っ
ているか、下回っているかを
示す矢印
バック
ライト
バックライトを5秒間点灯
作動させるには、モードボタン
を長押しします。.
1.クイックセットアップ
新品のコンピューターを取り付ける場合(またはバッ
テリーを交換した場合)、単位を選定してプログラム
しなければなりません。また、正しいセンサー信号(
Linkの場合は速度、LinkTeamの場合はさらにケイデン
スと心拍数)を指定しなければなりません。クイックセ
ットアップ、ペアリング、接続、およびリスタートの
4段階に従ってください。
セットアップ手順の開始方法
1.バッテリーを入れるか、リセットボタン(コンピューター本体裏
側の電池カバー下にある小さな銀色のボタン)を押します。→ホ
イール1のアイコンが現れ、「700-23」と表示されます。
2.ホイールのサイズを変更するには、スクロールボタンを連続し
て押します。
表(F7)を使用してタイヤサイズを選択するか、カス
タムサイズを設定します。
3.セットボタンを押し、選択モードにします。→KMHまたはMPHが
点滅します。
4.変更するには、スクロールボタンを連続して押します。
5.セットボタンを押し、選択モードにします。→゚Fまたは℃が点
滅します。
6.変更するには、スクロールボタンを連続して押します。
7.セットボタンを押し、選択モードにします。→12(12時間制時
計)が点滅します。
8.スクロールボタンを連続して押し、12時間制か24時間制を選
択します。
9.セットボタンを押し、選択モードにします。→時表示が点滅しま
す(AまたはP)。
10.時(Hour)を変更するには、スクロールボタンを連続して押
します。
11.セットボタンを押し、選択モードにします。→分表示が点滅
します。
12.分(Minutes)を変更するには、スクロールボタンを連続して
押します。
13.セットボタンを押し、選択モードにします。→”SPEED
PAIR?”と点滅表示されます。
14.以降の操作は次のペアリングの手順に従ってください。
2.ペアリング
LinkおよびLinkTeamは2.4GHzのデジタルコンピュー
ターです。回転数、ケイデンス、および心拍の各センサ
ーから送信されるコード信号を受信します。信号を受信
する前に、コンピューターおよびセンサーはペアとして
お互いを認識していなければなりません。一組のペア
は、近くのセンサーから干渉を受けないように、固有の
コードを使用します。
回転数、ケイデンス、および心拍の各センサーは特定
のタイプの信号を送信します。モードにかかわらず、コ
ンピューターはセンサーが送信する上記各タイプの信
号のみを認識します。たとえば、コンピューターは回
転数データについては回転数センサーからの信号しか
認識しません。
ペアリング手順には、「1.クイックセットアップ」の
手順14またはオンデマンド手順の2種類があります。ク
イックセットアップではすべてのデータが消去されま
す。オンデマンドの手順ではデータは消去されません。
使用開始時のセットアップは、クイックセットアップに
従って行ってください。
クイックセットアップ中にコンピューターの
ペアリングをする方法
1.コンピューターをバイクに取り付けるか、センサーから3フィー
ト(1メートル)以内の位置に置きます。
2.センサーから信号を送信します(回転数信号を送信するにはホ
イールを回転させます。ケイデンス信号を送信するにはクラン
クを回転させます。心拍信号を送信するには心拍ストラップを
装着します)。
3.セットボタンを長押しします。→PAIRノ
LINK LINK TEAM
→速度画面
が表示さ
れます。
ボタンを
放しま
す。
→”CADENCEPAIR?”と表示され
ます。
4.センサーから信号を送信します(ケ
イデンス信号の場合クランクを回
転させます)。
5.セットボタンを長押しします。→
PAIR→速度画面が表示されます。
ボタンを放します。
オンデマンドでコンピューターのペアリング
をする方法
センサーまたはメインユニットの電池を交換、また
はセンサーを交換した場合は、オンデマンド手順を使
用します。
1.コンピューターをバイクに取り付けるか、センサーから3フィー
ト(1メートル)以内の位置に置きます。
2.センサーから信号を送信します(回転数信号を送信するにはホ
イールを回転させます。ケイデンス信号を送信するにはクラン
クを回転させます。心拍信号を送信するには心拍ストラップを
装着します)。
3.スクロールボタンを両方押します。→”PAIR?”と表示されます。
4.セットボタンを長押しします。→PAIR→LinkおよびLinkTeamにつ
いては上の表を参照してください。
3.接続
走行が終了すると(LinkTeam心拍ストラップの場合
は身につけていない状態になると)、センサーは送信を
停止します。コンピューターは受信信号がない場合、信
号をスキャンします。
5分間スキャンしたあと、コンピューターはセンサー
との接続を解除し、スキャンを停止して、スタンバイモ
ードになります。スキャニングは電力を消費するので、
スタンバイモードにより電池の電力を節約することがで
きます。作動しない状態が20分間続くと、コンピュータ
ーはスリープモードになります。
スタンバイモードまたはスリープモードからデータ受
信を開始するには、コンピューターを各センサーに接
続しなければなりません。接続には以下の2種類の方法
があります。
スリープモードからの接続方法
1.センサーから信号を送信します(ホイールを回転させる、クラン
クをペダリングする、心拍ストラップを身につけるなどを受信範
囲内で行います)。
2.ボタンをどれか押してください。
コンピューターは自動的に各センサーに接続されま
す。これには数秒間かかることがあります。コンピュー
ターが信号を受診できなかった場合は、20秒経過後、速
度、ケイデンス、心拍の順に次のセンサーに移ります。
コンピューターがどのセンサーにも接続できなかった
場合、”--”が表示されます。以降の操作は、「スタンバ
イモードからの接続方法」の説明に従うか、トラブルシ
ューティングを参照してください。
スタンバイモードからの接続方法
1.センサーから信号を送信します(ホイールを回転させる、クラン
クをペダリングする、心拍ストラップを身につけるなどを受信範
囲内で行います)。
2.セットボタンとモードボタンを長押しします。→”0”が点滅しま
す。→”0”が点滅なしで表示されます。→数値が表示されます。
3.ボタンを放します。
“---”が表示された場合、コンピューターとセンサーの
距離、およびセンサーとマグネットの距離を点検してく
ださい。コンピューターが依然として接続していない場
合は、コンピューターのペアリングのステップに従う
か、トラブルシューティングを参照してください。
4.走行前の準備:リスタート
コンピューターには2セットのデータが記録されま
す。以下は、使用開始時からの累計データと前回のリス
タート以降の走行データです(心拍データは別個にセッ
トされます。「心拍数」を参照してください)。
•オドメーター TRP
•平均速度(SPEEDAVG)、最高速度(SPEEDMAX)
•平均ケイデンス(CADENCEAVG)、最高ケイデンス(
CADENCEMAX)
•走行時間(CLOCK)
リスタートの方法(走行データをゼロに戻
す)
1.時計が表示されるまで、モードボタンを連続して押します。
2.走行時間が表示されるまで、スクロールボタンを連続して押
します。
3.セットボタンとモードボタンを同時に長押しします。
走行時間の表示が”00:00:00”になっていれば、トリップモードはゼ
ロに設定されています。
4.ボタンを放します。
ホイールサイズの設定方法
このコンピューターでは、ホイールサイズのデータを
2種類まで登録することができます。「各機能の使用」
セクションの「速度」を参照してください。ホイールサ
イズの変更方法を以下に示します。
1.オドメーターが表示されるまで、モードボタンを連続して押
します。
2.左右のスクロールボタンを押します。→ホイールのアイコンが
変わります。
各機能の使用方法
速度
速度データの表示方法
現在の速度は常に表示されます。
1.セットボタンかモードボタンを連続して押し、速度を表示さ
せます。
2.平均速度および最高速度を表示するには、スクロールボタンを連
続して押します。
•AVG―平均速度
ペースメーカーにより、現在の速度が平均速度を上回っているか
下回っているかが示されます。
•MAX―最高速度
平均速度と最高速度のゼロリセットの方法
モードボタンとセットボタンを同時に長押ししま
す。→0.00にリセットされます。
ホイールサイズ1およびホイールサイズ2の
設定方法
1.セットボタンかモードボタンを連続して押し、速度を表示
させます。
2.セットボタンを長押しします。→ホイールのアイコンが表示
されます。
3.セットボタンを連続して押します。→ホイール1とホイール
2が切り替わります。
4.スクロールボタンを押して選択します。
5.使用するホイールのサイズが表示されるまでスクロールボタ
ンを連続して押します。
ホイール
サイズメニ
ュー
カスタムホイールサイズ
6.セットボタ
ンを押して
選択しま
す。
7.モードボタ
ンを押しま
す。→速度
画面が表示
されます。
6.ホイールの円周を測定します
(図F8)。
7.4桁の数字が表示されるまで
スクロールボタンを連続して
押します。
8.セットボタンを長押ししま
す。→1桁目が点滅します。
9.目的の数字になるまでスク
ロールボタンを連続して押
します。
10.セットボタンを押し、選択
モードにします。→2桁目が
点滅します。
11.他の桁の数字についても手
順9と10を繰り返します。
12.モードボタンを押します。→
速度画面が表示されます。
もう一方のホイールサイズを設定するには、上記の
手順を繰り返します。ただし、手順3では別のホイー
ルアイコンを選択してください。
時計
時間データの表示方法
1.セットボタンかモードボタンを連続して押し、時計を表示
させます。
2.時間(00:00P)または走行時間(00:00:00)が表示されるま
で、スクロールボタンを連続して押します。
時間の設定方法
1.セットボタンかモードボタンを連続して押し、時計を表示
させます。
2.セットボタンを長押しします。→12(12時間制時計)が点
滅します。
3.12時間表示と24時間表示を切り換えるには、スクロールボタ
ンを連続して押します。
4.セットボタンを押し、選択モードにします。→時表示が点滅し
ます(AまたはP)。
5.時間を変更するには、スクロールボタンを連続して押しま
す。
6.セットボタンを押し、選択モードにします。→分表示が点
滅します。
7.分を変更するには、スクロールボタンを連続して押します。
8.セットボタンを押し、選択モードにします。→時計画面が表
示されます。
オドメーター
距離データの表示方法
1.モードボタンかセットボタンを連続して押し、オドメーター
を表示させます。
2.スクロールボタンを連続して押し、TRPおよびTTLを表示
させます。
オドメーターの設定方法
1.モードボタンかセットボタンを連続して押し、オドメーター
を表示させます。
2.スクロールボタンを連続して押し、TTLを表示させます。
3.セットボタンを長押しします。→1桁目が点滅します。
4.目的の数字が表示されるまで、スクロールボタンを連続し
て押します。
5.セットボタンを押し、選択モードにします。→2桁目が点滅
します。
6.すべての桁の選択が終わるまで手順4と5を繰り返します。→
TTL画面が表示されます。
単位と測定法
MPH/KMH、および゜F/℃の設定
1.モードボタンかセットボタンを連続して押し、オドメーター
を表示させます。
2.スクロールボタンを連続して押し、TRPを表示させます。
3.セットボタンを長押しします。→MPHが点滅します。
4.KMHまたはMPHが表示されるまでスクロールボタンを連続
して押します。
5.セットボタンを押し、選択モードにします。→゜Fが点滅
します。
6.スクロールボタンを連続して押し、゜Fと℃を切り換えま
す。手順7はお使いのコンピューターのモデルに応じて選択
してください。
LINK LINK TEAM
7.セットボタ
ンを押し、
選択モード
にします。
→TRP画面
が表示され
ます。
7.セットボタンを押し、選択モ
ードにします。→CAd(ケイ
デンス)が表示され、OFFま
たはONが点滅します。
8.スクロールボタンを連続して
押し、OFFまたはONを選択
します。
9.セットボタンを押し、選択
モードにします。→Hr(心
拍)が表示され、OFFまたは
ONが点滅します。
10.スクロールボタンを連続し
て押し、OFFまたはONを選
択します。
11.セットボタンを押し、選択
モードにします。→TRPが表
示されます。
LinkTeamのみ
LinkTeamコンピューターはケイデンス(CAd)ま
たは心拍(Hr)を表示できます。この機能のどちら
かまたは両方を使用するには、その機能をONにセッ
トしなければなりません(上の「単位と測定法」を
参照してください)。
OFFになっている機能については、コンピュータ
ーはそのセンサーとのペアリングまたは接続をし
ません。
ケイデンス
ケイデンス機能を使用するには、ケイデンス機能を
ONにセットしなければなりません(上の「単位と測
定法」を参照してください)。
ケイデンスデータの表示法
1.モードボタンを連続して押し、ケイデンスを表示させます。
2.スクロールボタンを連続して押し、CUR、AVG、および
MAXを表示させます。
AVGとMAXをゼロにリセットするには
1.モードボタンを連続して押し、ケイデンスを表示させます。
2.モードボタンとセットボタンを同時に長押しします。→0.00に
リセットされます。
心拍数
この機能を利用するには、最寄りの販売店からオ
プションの心拍ストラップを購入してください。ま
た、心拍機能もONにセットしなければなりません(
上の「単位と測定法」を参照してください)。
心拍データの表示方法
1.モードボタンかセットボタンを連続して押し、心拍を表示
させます。
2.スクロールボタンを連続して押し、CUR、AVG、MAX、また
はZONEを表示させます。
AVGとMAXをゼロにリセットするには
1.モードボタンを連続して押し、心拍を表示させます。
2.モードボタンとセットボタンを同時に長押しします。→0.00に
リセットされます。
ZONEデータを表示させるには
1.モードボタンを連続して押し、心拍を表示させます。
2.スクロールボタンを連続して押し、ZONEを表示させます。
a.ゾーン内時間が表示されます。
b.ゾーン超過時間が表示されます。
c.ゾーン未満時間が表示されます。
ZONEを設定するには
1.モードボタンを連続して押し、心拍を表示させます。
2.セットボタンを長押しします。→SETZONEが表示されます。
→上限値の1桁目が点滅します。
3.スクロールボタンを連続して押し、数字を変更します。
4.セットボタンを押し、選択モードにします。→2桁目が点滅
します。
5.スクロールボタンを連続して押し、数字を変更します。
6.セットボタンを押し、選択モードにします。→3桁目が点滅
します。
7.セットボタンを押し、選択モードにします。→下限値が点
滅します。
8.下限値について手順3~7を繰り返します。→ZONE画面が表
示されます。
その他の情報
コンピューターをコンピューターベースか
ら取り外す
コンピューターを後方へ強く押します。ベース部を
押さないでください(図F3)。
トラブルシューティング
画面
に何も
表示さ
れない
コンピューターが出荷モード
になっています。任意のボタン
を押してください。
電池が切れているか、電池の
取り付け方法が間違っていま
す。新品または残量が十分ある
電池に交換してください。
デー
タが正
しく表
示され
ない
磁石の位置が間違っている
か、離れ過ぎています。磁石
とセンサーの位置を調整して
ください。
電池の残量が低過ぎます。電
池を交換してください。
車速
が表示
されな
磁石の位置が間違っている
か、離れ過ぎています。磁石
とセンサーの位置を調整して
ください。
速度
が正し
く表示
されな
ホイールサイズが間違ってい
ます。コンピューターを再設定
してください。
センサーが磁石を正しく読み
取っていません。磁石とセンサ
ーの位置を調整してください。
ケイ
デンス
が表示
されな
センサーが磁石を正しく読
み取っていません。磁石とセ
ンサーの位置を調整してくだ
さい。.
コンピューターがベース部に
はまっておらず、コンピュータ
ーとベース部の間の接点が接触
していません。取り付けをやり
直してください。
心拍
数が表
示され
ない
心拍ストラップの電池の残量
が低下しています。電池を交換
してください。
心拍ストラップが皮膚に接触
していません。湿らせて位置を
直してください。
ペア
リング
のエラ
コンピューターとセンサーの
間の距離が3フィート(1m)以
内であるか確認してください。
センサーの電池残量を点検し
てください。
電池残量低下
コンピューターが間違った情報を表示する場合は、
電池の残量が低下している可能性があります。コン
ピューターが誤作動する場合、または6ヶ月ごとに電
池を交換してください。新しい電池を購入するとき
は、販売店に古い電池を持参し、同じ種類の電池を
購入してください。
・CR2032、3Vリチウム電池
電池を取り外すと、すべての測定値がゼロにリセッ
トされます。新しい電池を取り付けた後、累積値を
再設定する場合は、古い電池を取り外す前に累積値
をメモしておいてください。
電池の交換方法
1.コンピューターをベースから取り外します。
2.電池カバーを確認します。
3.反時計回りに約1/4回転させます(図F5)。
4.電池カバーを取り外すと、電池が見えます。
ゴム製のOリングシールをなくさないように注意してください。
5.古い電池を取り外します。
6.+の印がある面を上に向けて新しい電池を取り付けます(
図F6)。
7.電池カバーとOリングシールを元のように取り付け、時計回り
に1/4回転させます。
限定保証
トレックジャパンでは新品でお買い上げいただいたインサイト
サイクルコンピューター6i、8i、9i、11i、ACH、およびACH
Digitalにおいて、製造上および材質上の欠陥について、
購入日より2年間保証いたします。
以下の場合は本保証の対象外となります。
•通常の使用による磨耗や摩損(電池の寿命を含む)
•不適切な組み立て
•購入されたコンピューターと適合しない部品やアクセサリ
ーの装備が原因で発生したトラブル
•事故、誤用、粗略な取扱い、あるいは不注意による損傷や
故障
・販売店側で発生したパーツ交換や変更にかかった人件費や工
賃、送料、交通費、通信費など
いかなる種類のものであっても、コンポーネントもしくは部品
に改造が施された場合、本保証は無効となります。
保証は、欠陥のあるコンポーネントまたはパーツの修理または
交換に限定され、これが保証サービスを実現する唯一の手段
となります。この保証は製品の購入日から効力を有し、保証
を受ける権利は自転車の最初の持ち主だけにあり、この権利
は譲渡できません。トレックは、付随的損害または拡大的損
傷については責任を負わないものとします。
この保証はトレック正規販売店を通じて行わなければなりませ
ん。その際、レシート等の購入を証明するものが必要です。
保証期間および保証内容は、商品の種類および国またはこ
の一方によって異なる場合があります。本保証は購入者の法
的権利を定めたものであり、この権利は地域により異なりま
す。本保証は購入者の憲法上の権限に影響を及ぼしません。

Leia este manual cuidadosamente e guarde-o para
referência futura. Se não perceber as informações deste
manual ou se tiver dúvidas sobre o computador Incite
que este manual não consiga explicar, consulte o seu
revendedor Trek ou contacte-nos:
Trek Bicycle Corporation
Ao cuidado de: Serviço a Clientes
801 W. Madison Street
Waterloo, Wisconsin 53594 E.U.A.
http://www.trekbikes.com +1 920.478.4670

Quando estiver a andar na bicicleta, não se
distraia a olhar fixamente para o computador
durante longos períodos de tempo (F1). Se não
prestar atenção à estrada, poderá colidir com um
obstáculo o que poderá resultar numa possível
perda de controlo da bicicleta e queda.


Existem quatro botões (F2):
A- Modo
B- Definir
C- Deslocar(dois botões: para cima e para baixo)
Existem três formas de usar os botões:
Premir – prima uma vez
Percorrer - premir repetidamente conforme necessário
Manter - premir e manter durante dois ou três segundos

RELÓGIO
CLK
TME
Hora apresentada em horas e minutos ou Tempo
de Viagem apresentado com segundos.
Formato de 12 horas com AM/PM ou formato
de 24 horas
Leitura máxima: 23:59 (Relógio) ou 23:59:59
(Tempo de Viagem)
ODÓMETRO
ODO
Distância percorrida, apresentada em milhas ou
em quilómetros.
TRP-Parcial (desde a última Reposição)
TTL- Total desde a última Reposição
Leitura máxima: 99,999
VELOCIDADE Apresenta a velocidade actual da bicicleta em
quilómetros por hora (KMH) ou em milhas por
hora (MPH)
AVG- Velocidade média desde a última
Reposição, apresentada até às décimas.
MAX- Velocidade máxima obtida desde a
Reposição
Leitura máxima do aparelho: 129,6kmh ou
80,5mph
RITMO Sempre apresentado. Indica se a velocidade actual
é superior ou inferior à velocidade média
Indicado por uma seta que aponta para cima
(superior) ou para baixo (inferior).
TEMPER-
ATURA
Sempre apresentado
Temperatura actual apresentada em graus
Celcius ou Fahrenheit, em números inteiros.
Leitura mínima: -2° F +/-2°, -19° C +/-1°
Leitura máxima: 140° F +/-2°, 60° C +/-1°
SELECÇÃO
DE RODA
Sempre apresentado (F4)
Indica qual a definição de roda em utilização
pelo computador
Roda 1
INCITE
ACH
Roda 2
INCITE
ACH

CADÊNCIA Rotações do eixo pedaleiro por minuto.
Apresentado em números inteiros
Leitura máxima: 240.
AVG- Cadência média desde a última Reposição
MAX- Cadência máxima obtida desde a
Reposição
RITMO
CARDÍACO
HR
Ritmo cardíaco em pulsações por minuto
CUR- Actual
AVG- Ritmo cardíaco médio desde a última
Reposição
MAX - Ritmo cardíaco máximo desde a última
Reposição
ZONE- Seta que indica se o ritmo cardíaco está
acima, abaixo ou situado no intervalo definido
RETRO-
ILUMINAÇÃO
Fornece iluminação durante 5 segundos.
Para activar, mantenha premido o botão Modo.

Quando o computador for novo (ou quando tiver
substituído a pilha), o computador tem de ser
programado com as unidades da preferência do
utilizador e os sinais correctos dos sensores têm de ser
definidos (Velocidade para o Link; também Cadência
e Ritmo Cardíaco para o Link Team). Siga os quarto
passos para Configuração Rápida, Emparelhar, Ligar e
Reiniciar.

1. Instale a pilha ou carregue no botão Repor (o pequeno
botão prateado na parte de trás do computador, abaixo
da tampa da pilha) 4 Será apresentado o ícone Roda 1
com a indicação “700-23”.
2. Utilize o botão Percorrer para alterar o tamanho da
roda.
Seleccione o tamanho da roda, utilizando a tabela (F7) ou defina um tamanho de
roda personalizado.
3. Prima o botão Definir para seleccionar 4 São apresen-
tados KMH ou MPH intermitentes.
4. Utilize o botão Percorrer para efectuar alterações.
5. Prima o botão Definir para seleccionar 4 São apresen-
tados C° ou F° intermitentes.
6. Utilize o botão Percorrer para efectuar alterações.
7. Prima o botão Definir para seleccionar 4 É apresentado
12 (relógio AM/PM) intermitente.
8. Prima o botão Percorrer para escolher entre o relógio de
12 ou de 24 horas.
9. Prima o botão Definir para seleccionar 4 É apresentada
a hora (A ou P).
10. Utilize o botão Percorrer para alterar a Hora.
11. Prima o botão Definir para seleccionar 4 São apresen-
tados os Minutos intermitentes.
12. Utilize o botão Percorrer para alterar os Minutos.
13. Prima o botão Definir para seleccionar 4 É apresen-
tado SPEED PAIR? (EMPARELHAR VELOCIDADE?)
intermitente.
14. Siga os passos na secção “Emparelhar”.

O Link e o Link Team são computadores digitais de
2.4Ghz. Recebem transmissões codificadas proveni-
entes dos sensores de Velocidade, Cadência e Ritmo
Cardíaco. Antes de o computador conseguir receber
estas transmissões, é necessário que o computador
e o sensor se reconheçam e fiquem Emparelhados. O
Emparelhamento utiliza um código exclusivo para que
não possa sofrer interferências de outros sensores nas
proximidades.
Cada sensor (Velocidade, Cadência e Ritmo Cardíaco)
envia um tipo de sinal específico. Num determinado
modo, o computador apenas reconhecerá os sinais
provenientes desse tipo de sensor. Por exemplo, o
computador apenas reconhecera dados de Velocidade
provenientes do sensor de Velocidade.
Existem dois procedimentos para proceder
ao Emparelhamento. O passo 14 da secção “1.
Configuração Rápida” ou a secção Configuração
Programada. A Configuração Rápida apaga todos os
dados do computador. O procedimento Configuração
Programada não apaga os dados. Para a configuração
inicial, consulte a secção Configuração Rápida.

1. Coloque o computador na bicicleta ou a 1 metro de
distância o sensor.
2. Provoque o envio de um sinal pelo sensor (rode a roda
da bicicleta para activar o sensor de Velocidade, rode
o eixo pedaleiro para o de Cadência ou coloque a fita
de monitorização do ritmo cardíaco para o de Ritmo
Cardíaco).
3. Mantenha premido o botão Definir 4 EMPARELHAR...
4
LINK LINK TEAM
4 É
apresen-
tado
o ecrã
Velo-
cidade.
Liberte
o botão.
4 É apresentado CADENCE
PAIR? (EMPARELHAR
CADÊNCIA).
4. Provoque o envio de um
sinal pelo sensor (rode o eixo
pedaleiro para a Cadência).
5. Mantenha premido o botão
Definir 4 EMPARELHAR... É
apresentado o ecrã Velocidade.
Liberte o botão.

Se substituir a pilha de um sensor ou do aparelho
principal, ou se mudar de sensores, utilize o procedi-
mento Configuração Programada.
1. Coloque o computador na bicicleta ou a 1 metro de
distância o sensor.
2. Provoque o envio de um sinal pelo sensor (rode a roda
da bicicleta para activar o sensor de Velocidade, rode
o eixo pedaleiro para o de Cadência ou coloque a fita
de monitorização do ritmo cardíaco para o de Ritmo
Cardíaco).
3. Prima ambos os botões de Deslocamento. 4
EMPARELHAR?
4. Mantenha premido o botão Definir 4 EMPARELHAR...
4 consulte a tabela acima para o Link e o Link Team.

Quando parar de andar de bicicleta (ou quando
remover a fita do sensor de ritmo cardíaco do Link
Team) o sensor não envia nenhum sinal. Quando o
computador não conseguir encontrar nenhum sinal,
executa um procedimento de procura.
Após cinco minutos de procura, o computador desliga-
se dos sensores, pára a procura e entra em modo de
Espera. Isto poupa a pilha porque a pesquisa gasta
energia da pilha. Após 20 minutos de inactividade, o
computador entra em modo de Inactividade.
A partir do modo de Espera ou de Inactividade, para
começar a receber dados tem de Ligar o computador a
cada sensor. Existem duas formas de Ligar:

1. Envie sinais do sensor (rode a roda, rode o eixo
pedaleiro e/ou use a fita do sensor de ritmo cardíaco
dentro do raio de alcance do aparelho).
2. Prima qualquer botão.
O computador ligar-se-á automaticamente a cada sensor. Esta operação
poderá demorar alguns segundos. Se o computador não conseguir encontrar
nenhum sinal, após 20 segundos passa ao sensor seguinte pela ordem definida:
Velocidade, Cadência, Ritmo Cardíaco.
Se o computador não conseguir estabelecer ligação a nenhum sensor, o ecrã
apresentará “- -”. Siga as instruções na secção “Ligar a partir do modo de
Espera” ou Resolução de Problemas.

1. Envie sinais dos sensores (rode a roda, rode o eixo
pedaleiro e/ou use a fita do sensor de ritmo cardíaco
dentro do raio de alcance do aparelho).
2. Mantenha premido o botão Definir e o botão Modo 4 É
apresentado um ”0” intermitente 4 O ”0” é apresentado
fixo 4 o valor é apresentado.
3. Liberte os botões.
Se for apresentado ---, verifique a distância entre o computador e o sensor, e
entre o sensor e o íman. Se o computador continuar a não estabelecer ligação,
siga os passos na secção Emparelhar o computador ou consulte a secção
Resolução de Problemas.


O computador regista dois tipos de dados: Os dados
totais desde o momento em que foi instalado e os dados
da Viagem desde a última Reposição (O Ritmo Cardíaco
é definido em separado; consulte a secção Ritmo
Cardíaco):
• ODÓMETRO VIAGEM
• VELOCIDADE MÉDIA, MÁX
• CADÊNCIA MÉDIA, MÁX
• RELÓGIO (Tempo de Viagem)

1. Percorra o botão Modo até obter RELÓGIO.
2. Utilize os botões Percorrer até obter Tempo de Viagem.
3. Mantenha premidos os botões Definir e Modo.
A definição do Tempo de Viagem apresenta ‘00:00.00’, indicando que foi reposta
a zero.
4. Liberte os botões.

O computador pode recolher dados de dois
tamanhos de roda diferentes. Consulte “Utilizar as
Funcionalidades, Velocidade”. Estas instruções mostram
como alterar a definição do segundo tamanho de roda.
1. Percorra o botão Modo até obter ODÓMETRO.
2. Prima o botão de Deslocamento da esquerda e da direita
4 o ícone da roda é alterado.



A velocidade actual é sempre apresentada.
1. Percorra o botão Modo ou o botão Definir até obter
VELOCIDADE.
2. Percorra os botões de Deslocamento até obter MÉDIA
e MÁX.
• MÉDIA velocidade média
• O indicador de ritmo indica se a velocidade actual
está acima ou abaixo da MÉDIA
• MÁX- velocidade máxima
 4
Mantenha premido os botões Modo e Definir 4 Reposto
a 0.00.

1. Percorra o botão Modo ou o botão Definir até obter
Velocidade.
2. Mantenha premido o botão Definir 4 É apresentado o
ícone de Roda.
3. Percorra o botão Definir 4 Roda 1 ou Roda 2.
4. Utilize o botão Percorrer para seleccionar.
5. Utilize os botões de Deslocamento para escolher o
tamanho da roda preferido.
MENU
TAMANHO
DE RODA
TAMANHO DE RODA
PERSONALIZADO
6. Utilize
o botão
Definir
para
seleccionar.
7. Prima
o botão
Modo 4
É apresen-
tado o ecrã
Velo-
cidade.
6. Determine a circunferência
da roda (F8)
7. Utilize o botão Defini para
inserir o número com 4
dígitos.
8. Mantenha premido o botão
Definir 4 o primeiro dígito
fica intermitente
9. Utilize o botão Percorrer
para obter o valor pretendido
10. Prima o botão Definir para
seleccionar 4 o número
seguinte fica intermitente
11. Repita os passos 9 e 10
para os restantes dígitos
12. Prima o botão Modo 4
É apresentado o ecrã SPD
(Velocidade).
Para definir o outro Tamanho de Roda, repita os passos mas no passo 3 escolha
a outra roda.


1. Percorra o botão Modo ou o botão Definir até obter
RELÓGIO.
2. Percorra os botões de Deslocamento até obter
Relógio (00:00P) ou Tempo de Viagem (00:00:00).

1. Percorra o botão Modo ou o botão Definir até obter
RELÓGIO.
2. Mantenha premido o botão Definir 4 É apresen-
tado 12 (horas) intermitente.
3. Percorra os botões de Deslocamento até obter 12
e 24.
4. Prima o botão Definir para seleccionar 4 É
apresentada a hora (A ou P).
5. Percorra os botões de Deslocamento para obter
Hora.
6. Prima o botão Definir para seleccionar 4 São
apresentados os Minutos intermitentes.
7. Percorra os botões de Deslocamento Minutos.
8. Prima o botão Definir para seleccionar 4 É
apresentado o ecrã do Relógio.


1. Percorra o botão Modo ou o botão Definir até obter
ODÓMETRO.
2. Percorra os botões de Deslocamento até obter TRP
(Parcial) e TTL (Total).

1. Percorra o botão Modo ou o botão Definir até obter
ODÓMETRO.
2. Percorra os botões de Deslocamento para obter
TTL.
3. Mantenha premido o botão Definir 4 o primeiro
dígito fica intermitente
4. Utilize os botões de Deslocamento para obter o
número preferido.
5. Prima o botão Definir para seleccionar 4 o número
seguinte fica intermitente.
6. Repita os Passos 4 e 5 até ter seleccionado todos os
dígitos 4 O ecrã apresenta TTL.


1. Percorra o botão Modo ou o botão Definir até obter
ODÓMETRO.
2. Percorra os botões de Deslocamento para obter TRP.
3. Mantenha premido o botão Definir 4 MPH fica
intermitente.
4. Percorra os botões de deslocamento para obter
KMH ou MPH.
5. Prima o botão Definir para seleccionar 4 É
apresentado Fº intermitente.
6. Percorra os botões de deslocamento para obter
ou C° e escolha o Passo 7 para indicar o modelo do
computador:
LINK LINK TEAM
7. Prima
o botão
Definir
para
selecci-
onar
4 É
apresen-
tado TRP
no ecrã.
7. Prima o botão Definir para
seleccionar 4 É apresentado
CAD (cadência) com OFF ou
ON intermitentes.
8. Percorra os botões de
deslocamento para obter OFF
ou ON.
9. Prima o botão Definir para
seleccionar 4 É apresentado
Hr (Ritmo Cardíaco) com
OFF ou ON intermitentes.
10. Percorra os botões de
deslocamento para obter OFF
ou ON.
11. Prima o botão Definir para
seleccionar 4 É apresentado
TRP no ecrã.

O computador Link Team tem capacidade para
apresenta as informações de Cadência (CAd) ou
de Ritmo Cardíaco (Hr). Para usar uma ou ambas
estas funcionalidades, tem de definir a funciona-
lidade para ON (consulte a secção “Unidades e
Medidas” acima).
Se uma função estiver desligada (OFF), o
computador não tentará EPARELHAR nem LIGAR
a esse sensor.

Para usar esta funcionalidade, tem de definir
a funcionalidade CADÊNCIA como ligada (ON)
(consulte “Unidades e Medidas” acima).

1. Percorra o botão Modo até obter Cadência.
2. Percorra os botões de Deslocamento até obter CUR
(actual), MÉD (média) ou MÁX (máxima).

1. Percorra o botão Modo até obter Cadência.
2. Mantenha premido os botões Modo e Definir 4
Reposta a 000.

Para utilizar esta funcionalidade, tem de adquirir
a fita do sensor de ritmo cardíaco num revendedor.
Também tem de definir a funcionalidade Ritmo
Cardíaco como ligada (ON) (consulte “Unidades e
Medidas” acima).

1. Percorra o botão Modo ou o botão Definir até obter
Ritmo Cardíaco.
2. Percorra os botões de Deslocamento até obter CUR
(actual), MÉD (média), MÁX (máxima) ou ZONA.

1. Percorra o botão Modo até obter RITMO
CARDÍACO.
2. Mantenha premido os botões Modo e Definir 4
Reposta a 000.

1. Percorra o botão Modo até obter Ritmo Cardíaco.
2. Percorra os botões de Deslocamento para obter
ZONA.
a. É apresentado um tempo Na Zona.
b. É apresentado um tempo Acima da Zona.
c. É apresentado um tempo Abaixo da Zona.

1. Percorra o botão Modo até obter Ritmo Cardíaco.
2. Mantenha premido o botão Definir 4 É apresen-
tado DEFINIR ZONA 4 o primeiro dígito do Limite
superior fica intermitente
3. Utilize os botões de Deslocamento para alterar o
número.
4. Prima o botão Definir para seleccionar 4 o
segundo dígito fica intermitente.
5. Utilize os botões de Deslocamento para alterar o
número.
6. Prima o botão Definir para seleccionar 4 o
terceiro dígito fica intermitente.
7. Prima o botão Definir para seleccionar 4 O Limite
inferior fica intermitente.
8. Repita os passos 3-7 para seleccionar o limite
inferior 4 É apresentado o ecrã Zona.


Prima firmemente no computador (não na base)
num sentido para trás(F3).

Ecrã em
branco
O computador está no modo de envio. Prima
um botão.
O computador não tem pilha ou está incor-
rectamente instalada. Reinstale uma bateria
com carga.
Dados
erráticos
O íman não está alinhado ou está demasiado
longe. Reajuste a colocação do íman e do sensor.
A pilha está com pouca carga. Substitua a pilha.
Não é
indicada a
velocidade
actual
O íman não está alinhado ou está demasiado
longe. Reajuste a colocação do íman e do sensor.
A velocidade
indicada
está incor-
recta.
O tamanho da roda está incorrecto. Reponha o
computador.
O sensor não está a ler o íman de forma
adequada. Reajuste o alinhamento entre o íman
e o sensor.
Sem cadên-
cia
O íman não está a ler o sensor adequadamente.
Reajuste o alinhamento entre o íman e o sensor.
Os contactos entre o computador e a base não
estão em contacto porque o computador não
está na base. Reinstale.
Sem ritmo
cardíaco
A pilha da fita do sensor de ritmo cardíaco está
fraca. Substitua a pilha.
A fita do sensor de ritmo cardíaco não está em
contacto com a pele. Humedeça e reposicione.
Erro de
emparelha-
mento
Certifique-se de que o computador e o sensor
está a menos de 1m de distância
Verifique a pilha do sensor

Se o computador fornecer informações erráticas,
a pilha pode estar fraca. Substitua as pilhas
sempre que o computador funcionar mal ou a cada
6 meses. Quando comprar novas pilhas, leve as
pilhas antigas consigo até à loja para referência.
CR2032, célula de lítio, 3 volts
Quando a pilha for removida, o computador
repõe automaticamente todas as funções a Zero.
Depois de instalar um nova pilha, poderá repor
manualmente os totais. No entanto, tem de tomar
nota destes valores antes de remover a pilha.

1. Remova o computador da base
2. Identifique a tampa do compartimento da pilha.
3. Rode no sentido oposto ao dos ponteiros do relógio
cerca de um quarto de volta (F5).
4. Levante a tampa da pilha expondo a pilha.
Tenha cuidado para evitar perder o O-ring destinado a selar o
computador.
5. Retire a pilha velha.
6. Coloque a nova pilha com a “cruz” e a etiqueta de
identificação voltadas para cima (Figura F6).
7. Volte a instalar a tampa da pilha (com o O-ring) e
rode um quarto de volta no sentido dos ponteiros
do relógio.

A Trek Bicycle Corporation garante todos os novos computa-
dores Incite contra defeitos de mão-de-obra e materiais.
Esta garantia cobre os computadores Trek Incite modelos 6i, 8i, 9i, 11i,
ACH e ACH Digital por um período de dois anos da data de venda.
Esta garantia não cobre o desgaste normal, incluindo a vida útil da
bateria.
• Montagem incorreta
• Instalação de peças ou acessórios que não se
destinavam originalmente ou não são compatíveis com o
componente como vendido
• Danos ou defeitos devidos a acidentes, uso indevido,
abuso ou negligência
Qualquer modificação do componente ou de suas peças torna
esta garantia totalmente nula.
Esta garantia se limita explicitamente ao conserto ou
troca de itens defeituosos, o que constitui o único recurso
da garantia. Esta garantia tem início na data de compra,
aplica-se apenas ao proprietário original e não é transfer-
ível. A Trek não se responsabiliza por danos incidentais ou
conseqüenciais. Alguns estados não permitem a exclusão de
danos incidentais ou conseqüenciais, então a exclusão acima
pode não se aplicar a você.
Reivindicações em conformidade com esta garantia precisam
ser feitas através de um revendedor autorizado. É necessária
a apresentação de uma comprovação da compra.
Esta garantia dá aos consumidores direitos legais especí-
ficos, os quais podem variar de um lugar para outro. Esta
garantia não afeta os direitos do consumidor previstos em
lei.


请仔细阅读本手册并妥善保管,以备
将来参考。如果您对本手册中的内容不
理解,或对本手册没有介绍的 Incite
算机存有疑问,请咨询 Trek 经销商,
或与我们
Trek Bicycle Corporation
Attn: Customer Service
801 W. Madison Street
Waterloo, Wisconsin 53594
USA
http://www.trekbikes.com
920.478.4670
安全及使
在骑自行车时,请不要长时间注视计
算机 (F1)。不注意前方道路很可能导
致与障碍物相撞,从而失控并摔
使用
计算机提供四个按钮 (F2):
A - Mode(模式)
B - Set(设置)
C - Scroll(滚动,包括两个按钮:
向上和向下)
有三种使用按钮的方法:
按下 - 按下一次
反复按下 - 根据需要重复按下
按住 - 持续按住 2 至 3 秒钟
CLK
TME
当日时间(显示
小时和分钟)或
骑行时间(精确
到秒)。
12 小时格式(
以 AM/PM 表示
上午/下午)或
24 小时格式
最高读数:
23:59(时钟)或
23:59:59(骑行
程表
ODO
已骑行距离(显
示单位:英里/公
里)。
TRP - 单次行
程(上次重新启
动至当前)
TTL - 累计行
程(上次重新启
动至当前)
最高读数:
99,999
始终显示当前车
速,单位为英里/
小时 (MPH) 或千
米/小时 (KMH)
AVG- 上次重
新启动至当前的
平均速度,精
确到小数点后
一位。
MAX - 上次重
新启动至当前的
最快速度
最高读数:
80.5mph 或
129.6kph
速器
始终显示。指
示当前速度是
快于还是慢于平
均速度
上箭头表示快于
平均速度;下箭
头表示慢于平均
速度。
始终显示
以整数显示当
前的华氏或摄氏
温度。
最低读数:-2°
F +/-2°,-19°
C +/-1°
最高读数:
140° F +/-2°,
60° C +/-1°
轮选
始终显示 (F4)
指示计算机使
车轮 1
INCITE
ACH
车轮 2
INCITE
ACH
仅限 Link Team
大齿盘每分钟的
旋转圈数
以整数形式显示
最高读数:240.
AVG- 上次重
新启动至当前的
平均转速
MAX- 上次
重新启动至当
前的最
HR
每分钟的心
跳频率
CUR- 当前心率
AVG - 上次
重置至当前的平
均心率
MAX- 上次
重置至当前的最
快心率
ZONE- 以箭头
的形式指示您的
心率是属于设定
心率区段、高于
设定区段还
提供长达五秒钟
的背光。
要激活背光,
请按住 Mode(
模式)
1. 快速
如果您的计算机是初次使用(或更换了
电池),则必须对其进行程序设定,以
选择各项指标使用的单位,同时须确保
计算机可识别正确的感应器信号(Link
的“速度”感应器以及 Link Team 的“转
速”和“心率”感应器)。请按照“快速
设置”、“配对”、“连接”和“重新
开始进
1. 安装电池或按下 Reset(重置)按钮
(位于计算机背面电池盖下方的银色
小按钮)。屏幕会显示车轮 1 图标
和“700-23”。
2. 反复按下 Scroll(滚动)按钮,更改
车轮尺寸。
参照图表 (F7) 选择轮胎尺寸,或自定义
车轮尺寸。
3. 按下 Set(设置)按钮进行选择 4
KMH 或 MPH 会闪烁。
4. 反复按下 Scroll(滚动)按钮进行
更改。
5. 按下 Set(设置)按钮进行选择 4
F° 或 C° 会闪烁。
6. 反复按下 Scroll(滚动)按钮进行
更改。
7. 按下 Set(设置)按钮进行选择 4
12(时制)会闪烁。
8. 反复按下 Scroll(滚动)按钮在 12(时
制)或 24(时制)之间切换。
9. 按下 Set(设置)按钮进行选择 4
Hour(小时)会闪烁(可选 A 或 P)
10. 反复按下 Scroll(滚动),对 Hour(
小时)进行更改。
11. 按下 Set(设置)按钮进行选择 4
Minutes(分钟)会闪烁。
12. 反复按下 Scroll(滚动)按钮,对
Minutes(分钟)进行更改。
13. 按下 Set(设置)按钮进行选择 4
SPEED PAIR?(是否对速度感应器进行
配对?)会闪烁。
14. 请按照“配对”部
2.
Link 和 Link Team 均为 2.4Ghz 数字计
算机。它们可以接受来自“速度”、“转
速”和“心率”感应器的编码传输信号。
在计算机能够接收这些传输信号前,您需
要对感应器和计算机进行配对设置,以便
它们可以互相识别。“配对”的感应器和
计算机使用特殊的编码,以避免附近的其
他感应器相互造成干扰。
每个感应器(速度、转速和心率)均分
别发出一种特定类型的信号。在给定模式
下,计算机只能识别该类型感应器发出的
信号。例如,计算机只能识别来自“速
度”感应器的“速度”数据。
您可以通过以下两种途径开始进行“配
对”操作:“1. 快速设置”部分的步骤
14 或按需设置。快速设置会清除计算机
内的所有数据。“按需设置”则不会清
除数据。对于初次设置,请按照“快速
设置”的步骤
在快速设置期间对计
1. 将计算机置于自行车上或距离感应器
3 英尺(1 米)以内的其他位置。
2. 使感应器发出信号(旋转自行车车
轮可发出“速度”信号,旋转曲柄可发
出“转速”信号,而佩戴心跳感应带可发
出“心率”信号)。
3. 按住 Set(设置)按钮 4 PAIR...(
配对…) 4
LINK LINK TEAM
4 出现
Speed(
速度)屏
幕。松
开按
4 出现 4
CADENCE
PAIR?(是
否对转速感
应器进行配
对?)。
4. 使感应器发
出信号(
旋转曲柄
发出“转
速”信
号)。
5. 按住 Set(设
置)按钮 4
PAIR...(配
对…) 4
现 Speed(
速度)屏
幕。松
根据需要对计算
如果您更换了感应器或主要部件中的电
池,或更换了感应器,请按照“按需设
1. 将计算机置于自行车上或距离感应器 3
英尺(1 米)以内的其他位置。
2. 使感应器发出信号(旋转自行车车轮发
出“速度”信号,旋转曲柄发出“转
速”信号,或佩戴心跳感应带发出“心
率”信号)。
3. 同时按下两个 Scroll(滚动)按钮 4
PAIR?(进行配对?)
4. 按住 Set(设置)按钮 4 PAIR...(配
对…) 4 请参阅上表中针对 Link
Link Team 的操作
3.
当您停止骑行(或卸下 Link Team 心
跳感应带)时,感应器将不再发出信
号。而计算机在找不到信号的情况下会
搜索信号。
搜索持续 5 分钟后,计算机将与感应器
断开连接,停止搜索并进入 Standby(待
机)模式。由于搜索也会耗费电池电量,
因此这样可以节省电池电量。计算机处
于不活动状态 20 分钟后会进入 Sleep(
休眠)模式。
如果您需要计算机从 Standby(待机)
或 Sleep(休眠)模式启动并接受数据,
则必须在计算机与每个感应器之间建立
连接。您可以
从休眠模式
1. 使感应器发出信号(在感应器有效范围
内转动车轮、蹬动曲柄和/或佩戴心跳
2. 按下任意按钮。
计算机会自动连接到每个感应器。这一
过程可能需要几秒钟的时间。如果计算机
无法找到信号,会在 20 秒钟后按照以下
顺序与下一感应器建立连接:速度感应
器、转速感应器、心率感应器。
如果计算机无法连接到任何感应器,屏
幕将显示“- -”。请按照“从待机模式建
立连接”的步骤进行操作,或参阅“故
从待机模式
1. 使感应器发出信号(在感应器有效范围
内转动车轮、蹬动曲柄和/或佩戴心跳
感应器)。
2. 按住 Set(设置)和 Mode(模式)按钮
4 “0”闪烁 4 “0”显示但不闪烁
4 会出现数值。
3. 松开按钮。
如果显示“ ---”,请检查计算机与感
应器之间的距离以及感应器与磁体之间的
距离。如果仍然无法连接计算机,请按照
对计算机进行配对设置的步骤操作
4. 开始骑行:
您的计算机可以记录两组数据:一组是
自安装之日起至当前的累计数据,另一
种是自上次重新启动至当前的“行程”数
据(心率数据是分别设置的,具体请参
阅“心率”部分):
ODOMETER TRP(里程表行程)
SPEED AVG, MAX(平均速度,最
快速度)
CADENCE AVG, MAX(平均转速,
最大转速)
CLOCK (Ride Time)(时钟,骑行
时间)
重新启动(将行程数据归零)
1. 反复按下 Mode (模式)按钮,直到出
现 CLOCK(时钟)。
2. 反复按下 Scroll(滚动)按钮,直到出
现 Ride Time(骑行时间)。
3. 按住 Set(设置)按钮和 Mode(模
式)按钮。
“骑行时间”设置读数为“00:00.00”,指
示行程设置已经归零。
4. 松开按
选择车轮
计算机可以选择两种不同的车轮尺寸数
据。请参阅“功能用法 - 速度”部分。
您可以通过这些指导学会如何更换到其
他车轮尺寸。
1. 反复按下 Mode(模式)按钮,直到出
现 ODOMETER(里程表)。
2. 按下左右 Scroll(滚动)按钮 4
轮图标将
功能
速度
查看速
屏幕上始终显示自行车当前的速度。
1. 反复按下 Mode(模式)或 Set(设置)按钮选
择 SPEED(速度)。
2. 反复按下 Scroll(滚动)按钮,直到出现
AVG和 MAX。
- AVG - 平均速度
- 感速器会指示当前速度是高于还是低于
平均速度
- MAX- 最快
重设 AVG 和 MAX 4 0
按住 Mode(模式)和 Set(设置)按钮 4
重设为“0.00”。
设置车轮尺寸 1 和车轮尺寸 2
1. 反复按下 Mode(模式)或 Set(设置)按钮选
择 SPEED(速度)。
2. 按住 Set(设置)按钮 4 出现“车轮”图
标。
3. 反复按下 Set(设置)按钮 4 出现“车轮
1”或“车轮 2”。
4. 按下 Scroll(滚动)按钮进行选择。
5. 反复按下 Scroll(滚动)按钮,根据自
车轮尺 自定义车
6. 按下 Set(
设置)按钮进
行选择。
7. 按下
Mode(
模式)按
4 出现
Speed(速
度)屏幕。
6. 确定车轮周长 (F8)
7. 反复按下 Scroll(
滚动)按钮选择
4 位数字。
8. 按住 Set(设置)
按钮 4 第一位
数字闪烁
9. 反复按下 Scroll(
滚动)按钮选
择数值
10. 按下 Set(设
置)按钮进行选
4 下一位数
字将闪烁
11. 重复步骤 9 和
10,对其他各位
数字进行设置
12. 按下 Mode(模
式)按钮 4
现 SPD(速度)
屏幕
要对其他车轮尺寸进行设置,请重复以上步
骤,但请在步骤 3 中选择其
时钟
查看时
1. 反复按下 Mode(模式)或 Set(设置)按钮,
选择 CLOCK(时钟)。
2. 反复按下 Scroll(滚动)按钮,选择 Clock(
时钟)(00:00P) 或 Ride Time(骑行时间)
(00:00:00)。
设置
1. 反复按下 Mode(模式)或 Set(设置)按钮,
选择 CLOCK(时钟)。
2. 按下 Set(设置)按钮 4 12(时制)将
闪烁。
3. 反复按下 Scroll(滚动)按钮选择 12 24。
4. 按下 Set(设置)按钮进行选择 4 Hour(小
时)会闪烁(可选 A 或 P)
5. 反复按下 Scroll(滚动)按钮选择小时。
6. 按下 Set(设置)按钮进行选择 4 Minutes(
分钟)会闪烁。
7. 反复按下 Scroll(滚动)按钮选择分钟。
8. 按下 Set(设置)按钮进行选择 4 出现
Clock(时钟)屏幕。
里程表
查看距
1. 反复按下 Mode(模式)或 Set(设置)按钮,
选择 ODOMETER(里程表)。
2. 反复按下 Scroll(滚动)按钮,直到出现
TRP(行程)和 TTL(累计行程)。
设置里
1. 反复按下 Mode(模式)或 Set(设置)按钮,
选择 ODOMETER(里程表)。
2. 反复按下 Scroll(滚动)按钮,直到出现
TTL(累计行程)。
3. 按住 Set(设置)按钮 4 第一位数字闪烁。
4. 反复按下 Scroll(滚动)按钮选择需要的
数字。
5. 按下 Set(设置)按钮进行选择 4 下一位
数字将闪烁。
6. 重复步骤 4 和 5,对各位数字进行设置 4
出现 TTL 屏幕。
单位和度量制
设置 Mph/Kph 和 F°/C°
1. 反复按下 Mode(模式)或 Set(设置)按钮,
选择 ODOMETER(里程表)。
2. 反复按下 Scroll(滚动)按钮选择 TRP(
行程)。
3. 按住 Set(设置)按钮__MPH 闪烁。
4. 反复按下 Scroll(滚动)按钮选择 KMH
MPH。
5. 按下 Set(设置)按钮进行选择 4
烁。
6. 反复按下 Scroll(滚动)按钮选择 F°
C°,然后根据计算机型号执行第 7 步操作
LINK LINK TEAM
7. 按下
Set(设
置)按钮
进行选
4
现 TRP(
行程)屏
幕。
7. 按下 Set(设置)按
钮进行选择 4
现 Cad(转速),
同时其 OFF(关
闭)或 ON(开
启)选项闪烁。
8. 反复按下 Scroll(
滚动)按钮选择
OFF(关闭)或
ON(开启)。
9. 按下 Set(设置)按
钮进行选择 4
现 Hr(心率),同
时其 OFF(关闭)
或 ON(开启)选
项闪烁。
10. 反复按下 Scroll(
滚动)按钮选择
OFF(关闭)或
ON(开启)。
11. 按下 Set(设置)
按钮进行选择 4
出现 TRP(行程)
屏幕。
仅限 Link Team
Link Team 计算机可以显示“转速”(CAd)
或“心率”(Hr)。要使用这些功能中的一项或全
部,您必须将该功能设置为 ON(开启)(请参
见上面的“单位和度量制”)。
如果将功能设置为 OFF(关闭),则计算机将
不会尝试与相应的感应器“配对”或“连接”。
转速
要使用此功能,必须将“转速”功能设置为
ON(开启)(请参见上面的
查看转
1. 反复按下 Mode(模式)按钮,直到出现
Cadence(转速)。
2. 反复按下 Scroll(滚动)按钮,直到出现
CUR(当前转速)、AVG(平均转速)或
MAX(最大转速)。
AVG 和 MAX 重置为
1. 反复按下 Mode(模式)按钮,直到出现
Cadence(转速)。
2. 按住 Mode(模式)和 Set(设置)按钮 4
重设为“000”。
心率
要使用此功能,请从经销商处购买心跳感应带
选件。另外,您还必须将“心率”功能设置为
ON(开启)(请参见上面的
查看心率
1. 反复按下 Mode(模式)或 Set(设置)按钮,
直到出现 Heart Rate(心率)。
2. 反复按下 Scroll(滚动)按钮,直到出现
CUR(当前心率)、AVG(平均心率)或
ZONE(区段)。
AVG 和 MAX 重置为
1. 反复按下 Mode(模式)按钮,直到出现
HEART RATE(心率)。
2. 按住 Mode(模式)和 Set(设置)按钮 4
重设为“000”。
查看区段
1. 反复按下 Mode(模式)按钮,直到出现
HEART RATE(心率)。
2. 反复按下 Scroll(滚动)按钮,直到出现
ZONE(区段)。
出现位于区段的心率的时间。
出现超出区段的心率的时间。
出现低于区段
设置 ZONE(区段)
1. 反复按下 Mode(模式)按钮,直到出现
HEART RATE(心率)。
2. 按住 Set(设置)按钮 4 出现 SET ZONE(
设置区段) 4 区段上限的第一位数字闪烁
3. 反复按下 Scroll(滚动)更改数字
4. 按下 Set(设置)按钮进行选择 4 第二位
数字闪烁。
5. 反复按下“Scroll”(滚动)更改数字
6. 按下 Set(设置)按钮进行选择 4 第三位
数字闪烁。
7. 按下 Set(设置)按钮进行选择 4 区段 4
下限数字闪烁。
8. 重复步骤 3-7 选择下限 4 出现 4 Zone(
区段)
其他信息
将计算机从
用力向后按计算机(不是底座)即可 (F3)。
故障
计算机处于运输模式
电池损坏,或安装不正
确。重新安装状态良好的
电池即可。
数据 磁体未对准或相距太
远。请重新调整磁体与感
应器的安
电池电量不足。
无法
显示当
前速
磁体未对准或相距太
远。请重新调整磁铁与感
应器的安
速度
读数
不正
确。.
车轮尺寸不正确。请重置
感应器不能从磁体正确
读数。请重新调整磁体与
感应器的
无法
显示转
感应器不能从磁体正确读
数。请重新调整磁体与感
应器的安装位置。
由于计算机不在底座上,
因此计算机与底座之间的
触点未接触
无法
显示心
心跳感应带电池电量
心跳感应带未接触皮肤。
请沾湿感应带并重新贴.
对“错
误”
确保计算机和感应器之间
的距离不超过 3英尺 (1 M)
检查感应
电池电
如果计算机信息出现紊乱,可能是电池电量不
足造成的。请在计算机出现故障时及时更换电
池,或每隔 6 个月更换一次。购买新电池时,最
好带上旧电池。
- CR2032,锂电池,3 V
卸下电池后,计算机会自动将所有功能的值重
置为零。您可以在安装新电池后手动设置所有功
能的值,但是在卸下电池前请务必记
更换
1. 将计算机从底座拆除。
2. 找到电池盖。
3. 逆时针方向旋转四分之一圈 (F5)。
4. 撬起电池盖,露出电池。
小心不要遗失 O 形的橡胶密封圈。
5. 取下旧电池。
6. 插入带有“十字型”标记的新电池,十字标记
朝上(图 F6)。
7. 将电池盖(和 O 形密封圈)盖回,然后顺时
有限质量保证:
特莱克自行车有限公司保证出厂的每台Incite电
脑没有工艺和材料缺陷。
本质量保证适用于特莱克6i、8i、9i、11i、
ACH和ACH Digital型Incite电脑,为期两年,自
销售之日开始计算。
但不适用于一般的磨损和撕扯,包括电池
寿命。
-
- 装配不当。
- 未按部件或附件的初始用途安装,或与
销售的元部件不兼容。
- 因事故、使用不当、滥用或疏忽导致的
损伤或故障。
用户私自改装产品的元件或部件的,本保证
将全部无效。
本保证只适用于有缺陷部件的修理或更换,只
是一种质量保证的补救措施。 本保证自产品购买
日开始生效,只适用于最初的买主,不得转让。
特莱克不对偶发损害或间接损害承担责任。 有些
州不允许厂家免于承担偶发损害或间接损害的责
任,因此上述免责声明可能不适合您。
本保证项下的索赔应由经授权的经销商提出。
提出索赔时必须提供购买凭证。
本保证让消费者享有某些合法权利,此类权
利可能因地而异。 本保证不妨碍消费者享有的
法定权利。
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Trek Incite ACH Alpine bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Trek Incite ACH Alpine in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info