603737
105
Verklein
Vergroot
Pagina terug
1/106
Pagina verder
HOME-USE SEWING MACHINE
with OEKAKI FUNCTION
OEKAKI 50
OEKAKI SERIES
Read this manual carefully before use and always follow the instructions.
Keep this manual in a convenient place for easy reference.
If you give the sewing machine to someone else, also give them this Instruction Manual.
Utility stitching page 44
OEKAKI (free-motion embroidering) page 72
For video tutorial, visit http://www.toyotaoekakisewing.com
Use the “sewing” and “OEKAKI ”
functions to create original
projects!
In addition to sewing utility stitches such as straight stitches and decorative stitches,
OEKAKI 50 is equipped with the “OEKAKI (free-motion embroidering)” function, allowing
you to embroider your own designs. Enjoy creating attractive projects with simple
operations using the foot controller.
Before use
One-touch switching from
operation panel
Switch the sewing mode between “utility stitching” and “OEKAKI (free-motion
embroidering)” with the press of a button.
* The presser foot must be replaced with the correct foot when the mode is
switched.
OEKAKI
(free-motion embroidering)
Utility stitching
OEKAKI
(free-motion embroidering)
Utility stitching
Foot controller function differs
depending on the mode
The sewing speed (for “utility stitching”) or stitch width (for “OEKAKI (free-motion
embroidering)”) is adjusted by how much the foot controller is pressed down.
Sewing speed adjustment Stitch width adjustment
4
Contents
1 Checking accessories
Accessories .........................................................................................................................................6
Separately sold accessories ..............................................................................................................8
2 Important safety instructions
Be sure to read this section before use ..........................................................................................10
Changing the power plug .................................................................................................................11
3 Functions of the machine
Part names ......................................................................................................................................... 14
Operation panel part names.............................................................................................................16
Functions of various parts ...............................................................................................................17
Operating the foot controller............................................................................................................18
Using the quick adviser ....................................................................................................................20
4 Sewing preparations
Connecting the power.......................................................................................................................22
Correct needle selection...................................................................................................................23
Changing the needle .........................................................................................................................24
Changing the presser foot................................................................................................................25
Changing the presser foot holder....................................................................................................26
5 Threading the sewing machine
Winding the bobbin...........................................................................................................................28
Threading the lower thread ..............................................................................................................32
Threading the upper thread..............................................................................................................34
Using the needle threader ................................................................................................................38
Pulling up the lower thread ..............................................................................................................42
6 Utility stitching
Selecting the stitch ...........................................................................................................................44
Selecting the stitch width .................................................................................................................45
Selecting the stitch length................................................................................................................46
Selecting the sewing speed .............................................................................................................47
Stitch patterns ...................................................................................................................................48
Relationship between the needle, thread and fabric, and adjusting the thread tension............52
5
EN
7 Sewing (utility stitching)
Basic operations ...............................................................................................................................54
Straight stitch ...........................................................................................................................54
Ending stitching .......................................................................................................................55
Thread cutting ..........................................................................................................................55
Reverse sewing ........................................................................................................................55
One stitch sewing ....................................................................................................................56
Advanced operations........................................................................................................................ 57
Zigzag sewing...........................................................................................................................57
Overcasting .............................................................................................................................. 58
Blind hem stitching..................................................................................................................60
Zipper insertion ........................................................................................................................ 63
Buttonhole sewing ...................................................................................................................66
Shortening jeans ......................................................................................................................68
8 Basics of OEKAKI (free-motion embroidering)
Features of OEKAKI (free-motion embroidering)........................................................................... 72
Relationship between the needle, thread and fabric in OEKAKI mode, and adjusting the thread
tension................................................................................................................................................73
9 Sewing (free-motion embroidering)
OEKAKI (free-motion embroidering) preparations ........................................................................74
Practicing free-motion embroidering ..............................................................................................78
Tacking...............................................................................................................................................84
10 Special sewing tips
Sewing thick or thin fabrics .............................................................................................................86
Sewing tube-shaped fabrics.............................................................................................................86
Sewing leather and vinyl ..................................................................................................................87
Sewing equally spaced lines of stitching .......................................................................................87
Adjusting the thread tension............................................................................................................88
When the fabric cannot be removed from the sewing machine ...................................................90
11 Troubleshooting
When the sewing machine is operating incorrectly.......................................................................92
When an error code appears............................................................................................................ 96
12 Maintenance and storage
Feed dog and hook maintenance ....................................................................................................98
Storage precautions........................................................................................................................103
13 Others
Recycling .........................................................................................................................................104
Servicing double-insulated products (230V–240V)......................................................................104
Specifications .................................................................................................................................. 105
6
Accessories
Open the package, and check that the following accessories are included.
Accessories in the package
Do not connect any controller (device) other than
that specified.
Do not use the power cord with any other
machine.
Do not use an extension cord with the power cord.
Only use the foot controller that is supplied with
this machine.
1 Checking accessories
123
456
78
1 Soft cover (×1)
2 Quick adviser holder (×1)
3 Power cord (×1)
4 Quick instructions (×1)
5 Instruction Manual CD-ROM (×1)
6 Foot controller (×1)
7 Starter kit (×1)
* For practicing free-motion embroidering
8 Warranty card (×1)
Caution
7
EN
Accessories in the extension table
Note
Only use bobbins designed
specifically for this sewing
machine. Specially designed
bobbins can be purchased at
http://www.home-sewing.com.
Otherwise, contact your retailer.
Some accessories are in the accessory box of the extension table. Open the
cover of the extension table, and take out accessories.
123
456
789
10 11
12 13
No. 18/110 (×2)
No. 14/90 (×2)
No. 11/75 (×1)
Ball point needle no. 11/75 (×1)
1 Zigzag sewing foot (×1)
* Installed on the sewing machine.
2 Overcasting foot (×1)
3 Gliding foot (×1)
4 Zipper foot (×1)
5 Blind stitch foot (×1)
6 Embroidering foot (×1)
7 Buttonhole foot (×1)
8 Non stick foot (×1)
9 Quilting guide (×1)
10 Needle plate screwdriver (×1)
11 Buttonhole cutter (×1)
12 Needle
13 Plastic bobbin (×5)
* One installed in the machine
Tip
Cover
8
Separately sold accessories
Various accessories are sold separately in order to expand the use of the sewing machine.
Purchasing separately sold accessories
These accessories can be purchased from our website (http://www.home-sewing.com). Otherwise, contact your
retailer.
123
456
789
1 Straight stitch foot
This presser foot is for sewing only straight
stitches.
It is useful when sewing thin fabrics.
2 Rolled hemming foot
This presser foot sews rolled hems at the
edge of fabric. It can be used when sewing the
ends of handkerchiefs and scarves.
3 Clear presser foot
Since this presser foot is transparent, the
stitching can be seen, making this presser foot
useful for sewing over a drawn pattern or
along drawn stitching lines.
4 Gathering foot
This foot can be used to easily make frills or
gathers in lace.
5 Piping foot
Since this presser foot is off center, it is useful
for attaching piping tape.
6 Walking foot
Since this presser foot is fed on top of the
fabric, it is useful for stretch fabric or quilted
fabric where misaligned stitching easily
occurs.
7 Flower stitch foot
This presser foot is useful for sewing circular
patterns.
8 Twin needle
Using two threads at the same time, patterns
can be sewn with parallel stitching.
9 Supplemental spool pin
This is used when sewing with the twin
needle.
9
EN
10
Be sure to read this section before use
These safety instructions are designed to prevent danger or damage arising from the incorrect operation of the
machine. Read carefully and always follow the instructions.
Explanation of “ Warning” and “ Caution”
Symbol explanation
2 Important safety instructions
Warning
An incorrect operation could result in death or serious injury.
Caution
An incorrect operation could result in injuries or damage to the machine.
Do not touch.
Prohibited actions
Required actions
Remove the power plug from the outlet.
11
EN
"UK ONLY Important Read carefully"
Changing the power plug
The wires in this main lead are colored in accordance with the following code:
BLUE-NEUTRAL; BROWN-LIVE (OR ACTIVE)
As the colors of the main lead of this appliance may not correspond with the colored markings identifying the
terminals in your plug - PROCEED AS FOLLOWS:
The earth plug pin is unnecessary. As the machine is designed under double insulation structure, the earth wire
is removed from the machine. The wire colored BROWN must be connected to the terminal marked L or A or
colored RED. The wire colored BLUE must be connected to the terminal marked N or colored BLACK. Neither
wire is to be connected to the earth terminal of a three-pin plug.
Warning
Use an AC 220 to 240 V power source.
Not doing so could cause an electric shock or a fire.
Do not allow the power cord to be damaged, modified, excessively bent, pulled or twisted.
Doing so could cause an electric shock or a fire.
If the power cord is damaged, it must be replaced by a cord designed specifically for this model.
Warning
When changing the power plug or cord, do not allow it to be repaired, disassembled or
modified, except at an authorized dealer or service center.
Doing so could cause an electric shock or a fire.
If, for any reason, the power plug of this product is removed, it should be immediately
disposed of safely and not stored where it could be inadvertently used again.
Not doing so could cause an electric shock or a fire.
Caution
Be sure to close the bobbin case cover before operating the machine.
Not doing so could cause injuries.
Before changing the needle or threading the upper or lower thread, use the main power
switch to “turn off” the sewing machine.
Not doing so could cause injuries.
Do not look away from the needle while operating the sewing machine.
Doing so could cause injuries.
Do not touch moving parts such as the needle, take-up lever or handwheel.
Doing so could cause injuries.
Do not place your hand or fingers under the needle.
Doing so could cause injuries.
12
Do not use when young children are near the machine.
Children shall not play with the machine as they could touch the needle and be injured.
When leaving the sewing machine after using it, use the main power switch to “turn off”
the sewing machine, and then remove the power plug from the outlet.
Not doing so could cause injuries.
Before using the sewing machine, make sure that the presser foot holder clamp screw,
needle clamp screw and needle plate screw are firmly tightened, and that the presser foot
is correctly set in the presser foot holder.
Not doing so could cause injuries.
Before removing covers, oiling or performing any other user maintenance procedures
described in this Instruction Manual, be sure to remove the power plug from the outlet.
Not doing so could cause injuries.
Do not perform the following actions.
Doing so could cause injuries.
Sewing without lowering the presser foot.
Sewing while the needle is incorrectly installed.
Using a bent needle.
Sewing while jerking the fabric.
Do not repair, disassemble or modify the sewing machine, except as described in this
Instruction Manual.
Doing so could cause an electric shock, a fire or injuries.
Only use this sewing machine for the intended purposes described in this Instruction
Manual.
Not doing so could cause injuries or damage.
Only use the manufacturer-recommended accessories described in this Instruction
Manual.
Not doing so could cause injuries or damage.
Do not drop or insert foreign objects into any gaps, such as those exposed when the face
cover or bobbin case is removed.
Doing so could cause injuries or damage.
Do not operate the sewing machine while any ventilation openings are plugged. Do not
allow lint, dust or any other material to accumulate in the foot controller or sewing
machine ventilation openings.
Doing so could cause injuries or damage.
Do not use the sewing machine outside.
Doing so could cause an electric shock or a fire.
Do not operate the sewing machine in a location where sprays are being used or oxygen
is being administered.
Doing so could cause a fire.
When the sewing machine is not in use, store it safely off the floor since protruding parts
may cause injuries if someone trips over it.
Not doing so could cause injuries.
Caution
13
EN
The machine can be used by, children aged from 8 years and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge, only if they are supervised or have been given proper
instructions concerning use of the machine in a safe way and fully understand the hazards involved.
Do not operate the sewing machine on an unstable surface such as a sofa or a bed.
If the sewing machine falls down, it could be damaged or cause injuries.
After using the main power switch to “turn off” the sewing machine, remove the power
plug from the outlet.
Not doing so could cause injuries or damage.
Caution
14
Part names
3 Functions of the machine
1 Thread cutter
2 Face cover
3 Take-up lever
4 Thread guide
5 Upper thread tension dial
6 Operation panel
7 Spool pin
8 OEKAKI (free-motion
embroidering) button
9 Reverse sewing button
10 Extension table
11 LED light (inside)
12 Needle clamp screw
13 Needle thread guide
14 Needle
15 Needle plate
16 Bobbin case
17 Bobbin case cover
18 Feed dog
19 Presser foot
20 Presser foot holder
clamp screw
21 Presser foot holder
22 Needle threader lever
23 Buttonhole lever
6
21
20
19
17
16
18
15
14
12
13
4
3
2
1
10
11
9
8
7
5
23
22
15
EN
24 Handwheel
25 Thread winder guide
26 Thread winding
spindle
27 Hollow handle for
carrying
28 Presser foot lever
29 Drop feed lever
30 Foot controller
storage space
31 Foot controller jack
32 Terminal box
33 Main power switch
34 Foot controller
35 Power cord
36 Quick adviser holder
25
30
35
34
29
28
27
26
31
36
32
33
24
16
Operation panel part names
From the operation panel on the front of the sewing machine, various stitch settings can be selected.
1 LED display
This displays the number of the selected stitch in addition to the selected settings and sewing speed. It
also displays the setting for the function LED that is lit.
2 (setting) buttons
These can be used to change the selected stitch and the settings.
3 (start/stop) button
Press to start or stop the sewing machine.
4 (needle up/down) button
Each press of the button raises or lowers the needle. Use this button when changing the sewing
direction or sewing intricate areas.
5 (function) button
Each press of the button selects one of the functions (7 through 10).
6 Function LEDs
The LED lights up to indicate the function selected with the function button. The setting can be changed
with the (setting) buttons only for the function whose LED is lit.
7 Stitch number
The number of the stitch selected in utility stitching mode will be indicated.
8 Stitch width
The width of the selected stitch can be changed.
9 Stitch length
The length of the selected stitch can be changed.
10 Sewing speed
The sewing speed can be changed. Press to sew slower, or press to sew faster. The selected
sewing speed will be maintained, even if another stitch is selected.
11 (OEKAKI (free-motion embroidering)) button
Each press of the button selects the utility stitching mode or the OEKAKI (free-motion embroidering)
mode. The button lights up in green when the machine is in the OEKAKI mode.
5
6
7
8
9
10
11
1
2
3
4
17
EN
Functions of various parts
The various parts of the sewing machine have the functions described below.
2
1
3
Up
Down
Upper thread tension dial
Turn this dial to increase or decrease the
tension of the upper thread.
Reverse sewing button
When a straight stitch is selected, the
machine will sew in reverse while the
reverse sewing button is pressed.
The machine will sew in reverse
when the reverse sewing button is
pressed without pressing the start/
stop button.
If a stitch other than a straight stitch
is selected, three reinforcement
stitches are sewn, and then the
machine stops.
Presser foot lever
When sewing, lower the presser foot lever to
lower the presser foot. (1)
When inserting fabric, lift up the presser foot
lever to raise the presser foot. (2)
The presser foot can be raised even higher by
raising the presser foot lever to 3.
* Since the presser foot lever does not remain in 3,
hold it in place while inserting the fabric. This
position is useful when sewing thick fabric.
Handwheel
Turn the handwheel to
manually raise and lower the
needle.
Note
Always turn the
handwheel towards
yourself (in the direction
of the arrow).
If it is turned in the
opposite direction, the
thread may become
tangled.
With the drop feed lever
at the back of the
machine, the feed dog
can be lowered or raised.
Drop feed lever
18
Operating the foot controller
When the foot controller is connected, the sewing machine cannot be started by pressing the start/stop
button. At the end of sewing, the machine can be stopped by pressing the start/stop button.
Operation
1 Press the ‘{’ side of the main power switch to turn off
the sewing machine.
* For details on connecting the power, refer to page 22.
2 Insert the foot controller connector into the foot
controller jack on the machine.
3 Press the ‘|’ side of the main power switch to turn on
the sewing machine.
4 Press on the foot controller to operate the sewing
machine.
The more you press the foot controller, the faster the machine
sews.
Release the foot controller to stop the machine.
* The speed set with “Sewing speed” (refer to page 47) will be the
maximum speed when the foot controller is pressed.
* In OEKAKI (free-motion embroidering) mode, operating the foot
controller changes the stitch width. (refer to page 72)
Do not connect any controller (device) other than that specified.
Before unplugging the foot controller cord from the jack, turn off the sewing machine.
Caution
Be sure to use the main power switch to turn off the sewing machine before
connecting the foot controller.
Not doing so could cause injuries.
Caution
Caution
Main power
switch
Connector
19
EN
Storing the foot controller
When the foot controller is not being used, it can be stored on the back of the sewing machine.
1 Wind the cord, and place it in the foot controller.
2 Secure the foot controller in the storage area at the
back of the sewing machine, as shown in the
illustration.
* Align the tabs on the sides of the foot controller with the grooves in
the storage space.
Removal
With your fingers, press in on the sides of the foot
controller, and then pull it towards you.
Groove
Tab
1
2
3
2
1
1
2
20
Using the quick adviser
Refer to the quick adviser when checking the procedures of basic operations and selecting a stitch.
Installation
When the quick adviser is installed on the sewing machine, you can easily check basic operating procedures
and stitch information.
Hook the holders of the quick adviser onto the handle
at the back of the sewing machine.
* When the quick adviser is not in use, it can be stored by folding it
down the back of the sewing machine
* In order to prevent the sewing machine from being tipped over, hold
it down when folding down the quick adviser.
Note
When the quick adviser is installed, do not push down on it with excessive force. Doing so could
cause damage.
Hollow
handle for
carrying
Tab
21
EN
Placing on a table
The quick adviser can be removed from the sewing machine and placed on a nearby surface such as a table.
Fold back the legs of the quick adviser as shown in
the illustration.
22
Connecting the power
1 Insert the power cord connector into the terminal box.
2 Insert the power plug into the outlet ensuring the outlet is in a safe and accessible position.
3 Press the ‘|’ side (power on) of the main power switch.
The power is turned on.
4 Sewing preparations
Warning
Do not touch the power plug with wet hands.
Doing so could cause an electric shock.
Hold the power plug when removing it from the outlet.
Not doing so could damage the cord and cause an electric shock, a fire or injuries.
Caution
Before plugging in the power cord, use the main power switch to turn off the sewing
machine.
Not doing so could cause injuries.
Power cord
Terminal box
Connector
Power plug
Main power switch
‘ I ’ (On)
‘ O ’ (Off)
23
EN
Correct needle selection
A bent needle is extremely dangerous since it may break during use. Before sewing, place the flat side of the
needle on a flat surface and check it. Do not use the needle if the space between the needle and flat surface is
uneven.
Other needle problems
Note
Since a bent or blunt needle is difficult to see, replace the needle if the sewing performance is poor.
The point of the
needle is blunt/worn
away.
The point of the
needle is bent.
Caution
Do not use damaged needles.
If a faulty needle is used, not only could it impair the sewing performance, but it could also
break, or damage the needle plate or hook.
Flat side of
needle
Flat surface
Flat surface
24
Changing the needle
We recommend placing fabric or paper over the needle plate in order to prevent the needle from falling in through
any holes in the needle plate.
1 Turn the handwheel towards yourself to raise the point of the needle higher than the needle
plate.
* The needle plate screwdriver will not turn while the needle is raised to its highest position.
2 Hold the needle in one hand, loosen the needle
clamp screw with the needle plate screwdriver,
and then remove the needle.
* Loosen the needle clamp screw until the needle can be
removed.
3 Position the flat surface of the needle towards the
back of the machine, and then insert the needle
until it contacts the pin.
* Good sewing results cannot be achieved if the needle does not
contact the pin.
Caution
Before changing the needle, use the main power switch to turn off the sewing machine.
Not doing so could cause injuries.
Be sure to dispose of broken needles in a safe manner.
Not doing so could cause injuries.
Tip
Needle plate
screwdriver
Needle
clamp
screw
Pin
Flat side of
needle
25
EN
Changing the presser foot
For video tutorial, visit http://www.toyotaoekakisewing.com
Removal
1 Raise the presser foot lever.
2 Turn the handwheel towards yourself to raise the
needle.
Note
Be sure to turn the handwheel towards yourself.
If the handwheel is turned in the opposite direction, the
thread may become tangled.
3 Push the presser foot holder button in the direction of
the arrow to release the presser foot.
Caution
Before changing the presser foot, use the main power switch to turn off the sewing
machine.
Not doing so could cause injuries.
Presser foot lever
Handwheel
Presser foot
holder button
Presser foot
26
Installation
1 Position the presser foot pin directly below the groove
in the presser foot holder.
2 Lower the presser foot lever to attach the presser foot.
* Raise the presser foot lever again to check that the presser foot is
securely attached.
In order to avoid losing the presser foot, we recommend storing the
machine, when it is not being used, with the needle and the presser
foot lowered.
Place a piece of fabric under the presser foot to protect the feed dog.
Changing the presser foot holder
Removal
1 Raise the presser foot lever.
2 Follow the procedure described in “Changing the presser foot” (refer to page 25) to remove
the presser foot.
3 Hold the presser foot holder with your right hand,
and then turn the needle plate screwdriver towards
the back of the machine with your left hand to
loosen the presser foot holder clamp screw.
Tip
Caution
Before changing the presser foot holder, use the main power switch to turn off the
sewing machine.
Not doing so could cause injuries.
Presser foot
holder
Groove
Presser
foot pin
Presser
foot
lever
Needle plate
screwdriver
Presser foot
holder clamp
screw
Presser foot
holder
27
EN
Installation
1 Raise the presser foot lever.
2 Align the presser foot holder with the presser bar.
3 Push up the presser foot holder until it contacts the
presser foot holder clamp screw, and then, while
holding the presser foot holder in place with your
right hand, turn the needle plate screwdriver
towards yourself with your left hand to tighten the
presser foot holder clamp screw.
Note
If the presser foot holder is not correctly installed, the needle may hit the presser foot or the stitching
will not be sewn correctly.
Caution
Firmly tighten the screw with the included screwdriver, and check that the needle does
not hit the presser foot.
If the screw is loose, the needle will hit the presser foot and break or bend, which could cause
injuries.
Presser bar
Presser foot
holder
Presser foot
holder clamp
screw
Presser foot
holder clamp
screw
28
Winding the bobbin
For video tutorial, visit http://www.toyotaoekakisewing.com
Note
Prepare a thread spool and specially designed bobbin.
Specially designed bobbins can be purchased from our website
(http://www.home-sewing.com). Otherwise, contact your retailer.
5 Threading the sewing machine
Thread guide
Spool of thread
Bobbin
29
EN
1 Turn off the sewing machine.
2 Pull up the spool pin, and then place the spool of
thread on it.
3 Pull the thread from the thread spool, and then
hold it with one hand (1) while passing it around
the thread guide with the other hand (2).
4 From the inside, pass the thread through the hole
in the bobbin as shown. Place the bobbin on the
thread winding spindle so the groove aligns with
the shaft projection.
5 Turn on the sewing machine.
Caution
While the bobbin is being wound, do not touch the thread winding spindle or the
handwheel.
Doing so could cause injuries.
Main power
switch
Spool of
thread
Spool pin
1
2
Thread guide
Thread
Hole
Groove
Bobbin
Shaft
projection
Thread
winding
spindle
Main power
switch
30
6 Slide the thread winding spindle in the direction of
the arrow until it snaps into place.
7 While holding the thread with your right hand,
press the (start/stop) button with your left
hand. Otherwise, begin winding the bobbin by
stepping on the foot controller.
After the thread has been wound around the
bobbin about 10 times, press the (start/stop)
button. Otherwise, release the foot controller to
stop the sewing machine.
8 Cut off the extra thread above the bobbin
hole.
* Cut off the thread so that no excess extends from the
bobbin hole.
The LEDs in the display
blink in sequence to
indicate that the bobbin is being wound.
31
EN
9 To change the bobbin winding speed, press the
(function) button until the LED lights
up, and then select the speed with the and
(setting) buttons. (refer to page 47)
* The bobbin winding speed appears only briefly in the LED
display.
10 Press the (start/stop) button. Otherwise, step
on the foot controller to continue winding the
bobbin.
When bobbin winding becomes slow, press the
(start/stop) button again. Otherwise, release
the foot controller to stop bobbin winding.
11 Return the thread winding spindle by sliding it in
the direction of the arrow (1), and then remove the
bobbin from the thread winding spindle and cut
the thread (2).
Note
If the thread winding spindle is not returned, the needle
does not move and sewing is not possible.
1
2
Thread
winding
spindle
32
Threading the lower thread
For video tutorial, visit http://www.toyotaoekakisewing.com
Open the bobbin case cover, and insert the bobbin into the bobbin case.
If the bobbin is incorrectly inserted into the bobbin case, the stitching will not be sewn correctly.
1 Turn off the sewing machine.
2 Remove the bobbin case cover by sliding it
towards yourself.
3 Insert the bobbin into the bobbin case so that the bobbin rotates counterclockwise when
thread is fed off.
Main power
switch
Bobbin case
cover
Bobbin case
Bobbin
Check the orientation of the bobbin.
Thread unwinding direction
Counterclockwise Clockwise
33
EN
4 Pass the thread through A, then B, and then pull
the thread to the back, as shown.
5 Pull out about 15 cm of thread to the back.
6 Insert the tabs on the bobbin case cover into the hook retainer grooves, and then push the
bobbin case cover closed.
Pass through the groove.
B
A
15 cm
Bobbin case
cover
Groove
Tab
Bobbin
case
cover
34
Threading the upper thread
For video tutorial, visit http://www.toyotaoekakisewing.com
1 Turn off the sewing machine.
2 Raise the presser foot lever.
3 Turn the handwheel towards yourself to raise the
take-up lever to its highest position.
Otherwise, press the (needle up/down) button
to raise the take-up lever to its highest position
before turning off the sewing machine in step 1.
* If the needle and take-up lever are not raised, they cannot be
threaded.
Thread guide
Spool of thread
Take-up lever
Main power
switch
Presser foot lever
Hand-
wheel
Take-up lever
35
EN
4 Pull up the spool pin, and then place the spool
of thread on it.
5 Pull the thread from the thread spool, and then
hold it with one hand (1) while passing it
around the thread guide with the other hand (2).
6 Pull the thread from the thread guide down
through the groove.
7 Wind the thread around from the right to the
left.
Spool of
thread
Spool pin
1
2
Thread guide
Groove
Thread
guide plate
36
8 Pass the thread up the groove next to the
thread guide plate, then through the take-up
lever from the right.
9 Pull the thread down through the same groove.
10 Pass the thread behind the needle thread
guide and to the right.
* The thread can easily be passed through the needle
thread guide by holding the thread in your left hand, then
feeding the thread with your right hand, as shown.
Take-up lever
Thread
guide plate
Groove
Needle
thread
guide
37
EN
11 Pass the thread behind the right side of the
needle thread guide.
12 Pull the thread to check that it passes through
the needle thread guide as shown.
13 From the front, pass the thread through the eye
of the needle.
* For details on using the needle threader, refer to page 38.
14 Pass the thread through the slit in the presser
foot, and then pull out about 15 cm of thread to
the back.
Eye of
needle
15 cm
Slit in presser foot
38
Using the needle threader
For video tutorial, visit http://www.toyotaoekakisewing.com
* Use sewing machine needles no. 11/75 through 18/110 with the needle threader. (Needle no. 14/90 is
included when the sewing machine is purchased.)
The needle cannot be threaded if the thread is too thick for the needle. For details on possible needle and
thread combinations, refer to “Relationship between the needle, thread and fabric, and adjusting the thread
tension” (page 52).
Preparing to use the needle threader
1 Turn the handwheel towards yourself until
the needle is in its highest position.
Otherwise, press the (needle up/down) button to
raise the needle before turning off the sewing machine.
* If the needle is not in its highest position, it cannot be threaded.
2 Raise the presser foot lever.
3 Check that the thread has been passed through the
needle thread guide.
Caution
Before using the needle threader, use the main power switch to turn off the sewing
machine.
Not doing so could cause injuries.
Presser foot lever
Needle
thread
guide
39
EN
Understanding the needle threader mechanism
Using the needle threader
1 Completely lower the needle threader lever, and then
hook the thread on guide A as shown in the
illustration.
2 Fully turn the needle threader lever to the back, and
pull the thread through the needle threader slots.
3 Slowly return the needle threader lever towards
yourself as much as possible.
Lower
Turn
1
2
Needle
Guide A
Guide B
Hook
Guide B
Needle threader slots
There is a hook within guide B.
The hook passes through the eye of the
needle, catches the thread, then pulls it
through the needle.
Needle
threader
lever
Guide A
Needle
threader slots
Check that the hook
catches the thread.
40
4 Check that the thread has passed through the
eye of the needle, and then release the needle
threader lever while releasing the thread.
* If the needle is not threaded, check that the needle has been
raised to its highest position, and then repeat the procedure
starting with step
1.
5 Pull the thread loop that formed behind the
needle towards the back of the sewing machine.
6 Pass the thread through the slit in the presser
foot, and then pull out about 15 cm of thread to
the back.
Slit in presser foot
15 cm
41
EN
42
Pulling up the lower thread
For video tutorial, visit http://www.toyotaoekakisewing.com
1 Raise the presser foot lever. Loosely hold the upper
thread with your left hand, and then turn the
handwheel towards yourself one full turn.
Otherwise, turn on the sewing machine, and then
raise the presser foot lever.
Loosely hold the upper thread with your left hand,
and then press the (needle up/down) button
twice with your right hand.
* The first time that the button is pressed, the needle is lowered.
The second time that the button is pressed, the upper thread
catches the lower thread and the needle is raised.
2 Lightly pull the upper thread with your left hand to
pull up the lower thread.
Do not pull
the thread
taut.
Lower
thread
43
EN
3 Pull out the lower thread to the front.
4 Align the two threads, pass them through the
slit and under the presser foot, and then pull
out about 15 cm of thread to the back.
Lower thread
15 cm
Presser
foot
Slit in presser
foot
44
Selecting the stitch
For video tutorial, visit http://www.toyotaoekakisewing.com
For details on the available utility stitches and presser feet, refer to page 48.
1 Press the (function) button until the LED
lights up.
* The stitch number appears in the LED display.
* Check that the OEKAKI (free-motion embroidering) button is not lit.
2 Press the (setting) buttons to select a stitch
number.
* Hold down the button to change the setting quickly.
[Example] To select the blind hem stitch:
Press the
button until “9” appears in the display.
6 Utility stitching
45
EN
Selecting the stitch width
The stitch width (zigzag width) can be adjusted to make the stitching wider or narrower.
1 Press the (function) button until the LED
lights up.
* The stitch width appears in the LED display.
2 Press the (setting) buttons to select a stitch width.
* The settings that are available differ depending on the selected stitch. For details, refer to “Stitch patterns” (page 48).
Each press of increases the stitch width (zigzag width).
Each press of decreases the stitch width (zigzag width).
Note
This setting cannot be changed with some stitches.
If the sewing machine is turned off or a different stitch is selected after this setting has been
changed, the setting will return to the default.
When the straight stitch with variable needle entry point is selected, changing the stitch width moves
the position of the needle.
Caution
After changing the stitch width, slowly turn the handwheel and check that the needle
does not hit the presser foot.
Otherwise, the needle may bend or break.
Not doing so could cause injuries.
Left needle entry point
LED display setting “0.0”
Center needle entry point
LED display setting “2.5”
Right needle entry point
LED display setting “5.0”
46
Selecting the stitch length
The stitch length can be adjusted to make the stitching wider apart or closer together.
1 Press the (function) button until the LED
lights up.
* The stitch length appears in the LED display.
2 Press the (setting) buttons to select a stitch length.
* The settings that are available differ depending on the selected stitch. For details, refer to “Stitch patterns” (page 48).
Each press of makes the stitching wider apart.
Each press of makes the stitching closer together.
Note
This setting cannot be changed with some stitches.
If the sewing machine is turned off or a different stitch is selected after this setting has been
changed, the setting will return to the default.
Caution
If the stitches become bunched together, increase the stitch length.
Continuing to sew with the stitches bunched together may result in the needle bending or
breaking, which could cause injuries.
47
EN
Selecting the sewing speed
The sewing speed can be increased or decreased.
1 Press the (function) button until the LED
lights up.
* The sewing speed appears in the LED display.
2 Press the (setting) buttons to select a sewing speed.
* The sewing speed can be set between 01 (slow) and 10 (fast).
If the foot controller is connected to the sewing machine, the sewing speed for a utility stitch is adjusted when
the foot controller is pressed.
Caution
48
Stitch patterns
Stitch no.
Application
Stitch
length
(default
setting)
Stitch
width
(default
setting)
Presser foot
Stitch
pattern
Straight stitch (center)
1.0–4.0
(2.0)
(2.5)
* Needle
position
Zigzag sewing foot Zipper foot Gliding foot
Straight stitch with variable
needle entry point
1.0–4.0
(2.0)
0–5.0
(0)
* Needle
position
Zigzag sewing foot
Reinforced straight stitch
1.0–3.0
(3.0)
(2.5)
* Needle
position
Zigzag sewing, appliqués
0–4.0
(3.0)
1.0–5.0
(4.0)
Mending, thin fabric
overcasting
0.5–4.0
(1.0)
3.0–5.0
(5.0)
Reinforced zigzag stitch
1.0–3.0
(3.0)
2.0–5.0
(5.0)
Decorative stitch
1.0–3.0
(3.0)
3.0–5.0
(5.0)
Thick fabric overcasting
1.0–3.0
(3.0)
3.0–5.0
(5.0)
Zigzag sewing foot Overcasting foot
Blind hem stitching
1.0–4.0
(2.0)
2.0–5.0
(4.0)
Zigzag sewing foot Blind stitch foot
Overcasting
1.0–4.0
(2.0)
2.0–5.0
(4.0)
Zigzag sewing foot Overcasting foot
Stretch stitching
2.5–4.0
(3.5)
1.5–5.0
(2.0)
Zigzag sewing foot
Decorative stitch
1.0–3.0
(3.0)
3.0–5.0
(5.0)
1
2
3
4
5
6
7
8
9
10
11
12
49
EN
Overcasting
1.0–3.0
(3.0)
3.0–5.0
(5.0)
Zigzag sewing foot Overcasting foot
Appliqués
2.0–3.0
(3.0)
2.0–5.0
(5.0)
Zigzag sewing foot
Shell tuck stitching
2.0–3.0
(3.0)
2.0–5.0
(5.0)
Blind hem stitching
0.5–4.0
(1.0)
3.0–5.0
(4.0)
Zigzag sewing foot Blind stitch foot
Decorative stitch
0.5–4.0
(1.0)
3.0–5.0
(4.0)
Zigzag sewing foot
Decorative stitch
2.0–4.0
(2.0)
2.0–5.0
(5.0)
Decorative stitch
2.0–4.0
(2.0)
2.0–5.0
(5.0)
Decorative stitch
2.0–4.0
(2.0)
2.0–5.0
(5.0)
Decorative stitch
2.0–4.0
(2.0)
2.0–5.0
(3.5)
Decorative stitch
2.0–4.0
(2.0)
2.0–5.0
(3.5)
Decorative stitch
0.5–3.0
(0.5)
2.0–5.0
(5.0)
Decorative stitch
1.0–3.0
(3.0)
3.0–5.0
(5.0)
Decorative stitch
1.5–3.0
(2.0)
3.0–5.0
(5.0)
Stitch no.
Application
Stitch
length
(default
setting)
Stitch
width
(default
setting)
Presser foot
Stitch
pattern
13
14
15
16
17
18
19
20
21
22
23
24
25
50
Decorative stitch
1.5–3.0
(3.0)
3.0–5.0
(5.0)
Zigzag sewing foot
Decorative stitch
1.0–3.0
(2.0)
3.0–5.0
(5.0)
Decorative stitch, scalloping
0.4–1.0
(0.6)
3.0–5.0
(5.0)
Decorative stitch
0.4–1.0
(0.6)
3.0–5.0
(5.0)
Decorative stitch
1.5–3.0
(2.0)
2.0–5.0
(5.0)
Decorative stitch
0.4–1.0
(0.6)
3.0–5.0
(5.0)
Decorative stitch
0.4–1.0
(0.6)
3.0–5.0
(5.0)
Decorative stitch
1.5–3.0
(2.0)
3.0–5.0
(5.0)
Decorative stitch
1.0–3.0
(1.0)
3.0–5.0
(5.0)
Decorative stitch
1.5–3.0
(2.5)
3.0–5.0
(5.0)
Decorative stitch
1.5–3.0
(2.5)
3.0–5.0
(5.0)
Decorative stitch
1.5–3.0
(2.5)
3.0–5.0
(5.0)
Decorative stitch
1.5–3.0
(2.5)
(2.5)
* Needle
position
Stitch no.
Application
Stitch
length
(default
setting)
Stitch
width
(default
setting)
Presser foot
Stitch
pattern
26
27
28
29
30
31
32
33
34
35
36
37
38
51
EN
Decorative stitch
0.4–1.0
(0.6)
3.0–5.0
(5.0)
Zigzag sewing foot
Decorative stitch
1.5–3.0
(2.0)
3.0–5.0
(4.0)
Decorative stitch
0.4–1.0
(0.6)
3.0–5.0
(5.0)
Decorative stitch
0.4–1.0
(0.6)
3.0–5.0
(5.0)
Decorative stitch
1.0–3.0
(2.0)
3.0–5.0
(4.0)
Decorative stitch
0.0–4.0
(1.0)
(5.0)
Decorative stitch
0.0–4.0
(1.0)
(5.0)
Decorative stitch
0.0–4.0
(1.0)
(5.0)
Decorative stitch
1.5–3.0
(2.0)
3.0–5.0
(4.0)
Buttonhole (normal)
0.5–1.1
(0.5)
3.0–5.0
(4.0)
Buttonhole foot
Buttonhole (round-ended)
0.5–1.1
(0.5)
3.0–5.0
(4.0)
Buttonhole (keyhole)
0.5–1.1
(0.5)
4.0–5.0
(5.0)
Stitch no.
Application
Stitch
length
(default
setting)
Stitch
width
(default
setting)
Presser foot
Stitch
pattern
39
40
41
42
43
44
45
46
47
48
49
50
52
Relationship between the needle, thread and fabric, and adjusting
the thread tension
The quality of the sewing finish will improve if the needle and thread are selected to match the type of fabric used.
Follow the recommendations in the table below.
Use a ball point needle for the sewing alignment of stretch fabric.
When purchasing any needles not included as accessories, check that they are specified as home-use
sewing machine needles.
Use the same type of threads for the upper and lower threads.
The larger the needle number, the thicker the needle. The larger the thread number, the thinner the thread.
It may be necessary to adjust the upper thread tension according to the fabric, thread and needle
combination. (Refer to page 88.)
<Selecting a needle suitable for the thread>
Pass the thread to be used through the eye of the needle, and then hold both
ends of the thread to give the thread slack so that the needle slides along it, as
shown.
If the needle does not catch, the needle and thread are a good combination.
Since a needle that is too thick for the thickness of the thread will result in poor-
quality stitching, select the needle with the smallest number possible, which will
not catch on the thread.
If the needle frequently catches on the thread or does not slide along it, stitching
of poor quality will be produced. In this case, select a needle with a different
number or a different type of thread.
Normally, sew with the upper thread tension dial set to “ ”.
Thin fabrics Normal fabrics Thick fabrics
Relationship between the needle,
thread and fabric
Needle
No. 11/75 No. 14/90 No. 18/110
Thread
Polyester No. 90
Cotton No. 80 to No. 120
Silk No. 80
Polyester No. 50 to
No. 60
Cotton No. 60 to No. 80
Silk No. 50 to No. 80
Polyester No. 30 to
No. 50
Cotton No. 40 to No. 50
Silk No. 50
Fabric
Lining
Cuprammonium rayon
Georgette
Lawn
Lace, etc.
Normal clothing fabric
Broad
Soft denim
Satin
Pile
Gingham, etc.
Curtains
Denim
Quilting
Fleece
Tweed
Felt, etc.
Reference
thread tension
Upper thread
tension dial
-1 – -3 +1 – +5
Tip
+1
+2
-
1
-
2
-
1
-
3
+1
+2
-
1
+2
+3
+4
+1
Thread
Needle
53
EN
54
Basic operations
Straight stitch
For video tutorial, visit http://www.toyotaoekakisewing.com
1 Select the stitch in the operation panel.
* Check that the OEKAKI (free-motion embroidering) button is not lit.
* Refer to “Selecting the stitch” (page 44).
2 Select the stitch length
* Refer to “Selecting the stitch length” (page 46).
3 Press the (needle up/down) button to raise the needle.
4 Position the fabric under the presser foot, and then lower the presser foot lever.
5 Lightly guide the fabric with your hands, and then press the (start/stop) button.
Otherwise, begin sewing by stepping on the foot controller.
* For details on changing the sewing speed, refer to “Selecting the sewing speed” (page 47).
When the foot controller is connected, the sewing machine cannot be started by pressing the start/stop
button. At the end of sewing, the machine can be stopped by pressing the start/stop button.
7 Sewing (utility stitching)
Caution
Before changing the presser foot, use the main power switch to turn off the sewing
machine.
Not doing so could cause injuries.
Do not pull the fabric excessively while sewing.
Doing so could break the needle and cause injuries.
Caution
1
2
OEKAKI
button
not lit
Zigzag
sewing
foot
Presser foot to be used
Suitable stitch
55
EN
Ending stitching
Press the start/stop button, or release the foot controller, to
stop the sewing machine.
If sewing is finished, raise the presser foot, and then pull the
fabric to the back.
* If the fabric cannot be removed, turn the handwheel
towards yourself until the needle is in its highest position,
and then pull out the fabric.
Thread cutting
Line up the two threads, and then cut them with the thread
cutter on the face cover.
Reverse sewing
Reverse sewing is performed at the beginning and the end of
sewing to prevent the thread from unraveling.
Reverse stitches are sewn while the reverse sewing button is
pressed.
* Sew 3 to 4 reverse stitches at the beginning and end of
sewing to prevent unraveling.
* Remove your finger from the reverse sewing button to
return to forward direction sewing.
* If a stitch other than a straight stitch is selected, three
reinforcement stitches are sewn, and then the machine
stops.
Thread
cutter
Reverse sewing
button
56
One stitch sewing
Use this when changing the sewing direction.
1 When the sewing machine is stopped with the
needle raised, press the (needle up/down)
button.
The needle is lowered into the fabric.
2 Lift up the presser foot lever, and then turn
the fabric in the desired sewing direction.
3 Lower the presser foot lever, and then continue sewing.
* Pressing the needle up/down button again will raise the needle.
* By repeating one stitch sewing operation, it is possible to sew step by step.
* The same procedure can be done by tapping on the foot controller.
Presser foot lever
57
EN
Advanced operations
Zigzag sewing
1 Select the stitch in the operation panel.
* Check that the OEKAKI (free-motion embroidering) button is not lit.
* Refer to “Selecting the stitch” (page 44).
2 Select the stitch width and stitch length.
* Refer to “Selecting the stitch width” (page 45) and “Selecting the stitch length” (page 46).
3 Press the (needle up/down) button to raise the needle.
4 Position the fabric under the presser foot, and then lower the presser foot lever.
5 Lightly guide the fabric with your hands, and then press the (start/stop) button.
Otherwise, begin sewing by stepping on the foot controller.
* For details on changing the sewing speed, refer to “Selecting the sewing speed” (page 47).
When the foot controller is connected, the sewing machine cannot be started by pressing the start/stop
button. At the end of sewing, the machine can be stopped by pressing the start/stop button.
Caution
Before changing the presser foot, use the main power switch to turn off the sewing
machine.
Not doing so could cause injuries.
Caution
4
5
6
OEKAKI
button
not lit
Zigzag
sewing
foot
Suitable stitch
Presser foot to be used
58
Overcasting
For video tutorial, visit http://www.toyotaoekakisewing.com
This is a sewing method that prevents unraveling at the edge of the fabric.
When using the overcasting foot
1 Select the stitch in the operation panel.
* Check that the OEKAKI (free-motion embroidering) button is not lit.
* Refer to “Selecting the stitch” (page 44).
2 Select the stitch width and stitch length.
* Refer to “Selecting the stitch width” (page 45) and “Selecting the stitch length” (page 46).
3 Press the (needle up/down) button to raise the needle.
4 Position the fabric under the presser foot, and then lower the presser foot lever.
5 Sew with the edge of the fabric against the guide on
the foot.
* By sewing with the fabric against the guide, the stitching can be
sewn without having to constantly check the needle entry point.
Caution
When using the overcasting foot, select stitch number 4, 8, 10 or 13, and set the stitch
width to 5.0.
Not doing so could cause the needle to hit the presser foot and break, which may result in
injuries.
Caution
After changing the stitch width, slowly turn the handwheel and check that the needle
does not hit the presser foot.
Not doing so could break the needle and cause injuries.
OEKAKI
button
not lit
Suitable stitch
4
8
10
13
Presser foot to be used
Overcasting
foot
Guide
59
EN
When using the zigzag sewing foot
1 Select the stitch in the operation panel.
* Check that the OEKAKI (free-motion embroidering) button is not lit.
* When sewing thin fabrics, select stitch number 5.
* When sewing stretch fabrics, select stitch number 13, 15, 18, 22 or 26.
* Refer to “Selecting the stitch” (page 44).
2 Select the stitch width and stitch length.
* Refer to “Selecting the stitch width” (page 45) and “Selecting the stitch length” (page 46).
3 Press the (needle up/down) button to raise the needle.
4 Position the fabric under the presser foot, and then lower the presser foot lever.
5 Position the fabric so that the needle extends
slightly off the edge of the fabric when the
needle moves to the right.
OEKAKI
button
not lit
Suitable stitch
13
5
15
18
22
26
Presser foot to be used
Zigzag
sewing
foot
Right needle entry point
60
Blind hem stitching
For video tutorial, visit http://www.toyotaoekakisewing.com
Use this sewing method to sew the hems of skirts and pants with blind stitches. With this method, the stitching
cannot be seen from the front of the fabric.
1 Select the stitch in the operation panel.
* Check that the OEKAKI (free-motion embroidering) button is not lit.
* Refer to “Selecting the stitch” (page 44).
2 Select the stitch width and stitch length.
* Refer to “Selecting the stitch width” (page 45) and “Selecting the stitch length” (page 46).
3 Sew overcasting along the edge of the
fabric, and then fold the fabric as
shown.
* Tack or iron a crease 6 to 8 mm from the edge of
the fabric.
* For details on tacking, refer to “Tacking” (page
84), or stitch by hand.
4 At the tacking or the crease that was
ironed, fold back the fabric so that
wrong side faces upward.
5 Press the (needle up/down) button to raise the needle.
9
16
OEKAKI
button
not lit
Suitable stitch
Presser foot to be used
Blind stitch
foot
Right
side
Right
side
Wrong
side
Wrong
side
Overcasting Tacking or
crease
6 – 8 mm
Hemline
Wrong side
Fold
Overcasting
61
EN
6 Turn the handwheel towards yourself until the
needle is as far as possible to the left.
7 Position the fabric so that the needle slightly
catches the fold.
* Only catch 2-3 threads on the project fold as shown below
in correct stitching diagram.
8 Lower the presser foot, adjust the adjusting
screw so that the fold aligns with the guide, and
then sew with the fold against the guide.
Use invisible thread when sewing hems.
Transparent for light colored fabric
Shaded for dark colored fabric
Tip
Correct Incorrect
Small stitches evenly aligned on right
side of fabric
(When unfolded)
Needle catches too much of the fold
(Large stitches on right side)
Needle does not catch the fold
(Blind hem stitches do not come
through)
* Refer to steps 6 to 8 and follow the instructions carefully.
Needle on
left side
Project
fold
Needle on left side
Adjusting
screw
Guide
Project
fold
Right sideWrong side
Right sideWrong side
Right sideWrong side
62
63
EN
Zipper insertion
For video tutorial, visit http://www.toyotaoekakisewing.com
With this method, the left side of the zipper is sewn first.
1 From the operation panel, select stitch number 1 (straight stitch (center)).
* Check that the OEKAKI (free-motion embroidering) button is not lit.
* Refer to “Selecting the stitch” (page 44).
2 Select the stitch length
* Refer to “Selecting the stitch length” (page 46).
Caution
While sewing, do not allow the needle to hit the zipper teeth.
Doing so could break the needle and cause injuries.
1
OEKAKI
button
not lit
Presser foot to be used
Zipper foot
Suitable stitch
64
Sewing the left side of the zipper
1 Align the zipper and fabric, and tack them together.
* For details on tacking, refer to “Tacking” (page 84), or sew tacking by
hand.
2 Attach the right-side pin of the zipper foot to the presser
foot holder.
3 Position the fabric so that the zipper is on the right side of
the presser foot and groove runs on the zip teeth.
4 Sew until just before the presser foot makes contact with
the slider, and then stop the sewing machine.
5 Turn the handwheel towards yourself to lower the needle
into the fabric. Otherwise, press the (needle up/down)
button to lower the needle.
Tacking
Right-side pin
Needle entry
point
Zipper foot
Zipper
Slider
65
EN
6 Raise the presser foot lever.
7 Move the slider behind the presser foot, lower the
presser foot lever, and then finish the sewing.
Sewing the right side of the zipper
Release the presser foot, and then attach the left-side pin to the
presser foot holder.
Sew the right side of the zipper using the same procedure as for the
left side.
Sewing in the same direction as on the left side will help prevent sewing
misalignment.
Tip
Slider
Left-side pin
66
Buttonhole sewing
For video tutorial, visit http://www.toyotaoekakisewing.com
Buttonholes can be sewn to match the size of the button. With stretch fabrics or thin fabrics, it is recommended
to use a stabilizer for a better buttonhole finish.
1 Select the stitch in the operation panel.
* Check that the OEKAKI (free-motion embroidering) button is not lit.
* Refer to “Selecting the stitch” (page 44).
* Before sewing buttonholes, check the stitch length and stitch width by sewing a trial buttonhole on a scrap piece of
fabric.
* Maximum size of the button is diameter 25.4mm.
The buttonhole will automatically be sewn in the order of the numbers shown in the illustration.
2 Mark the position of the beginning of sewing for the
buttonhole.
3 Pull out the button holder plate on the presser foot,
and then insert the button to fit into the holder.
* The size of the buttonhole to be sewn is determined by the size of
the button placed in the button holder plate.
OEKAKI
button
not lit
Presser foot to be used
Buttonhole
foot
Suitable stitch
48
49
50
15 36
0
8
29
47
Illustration of
finished buttonhole
Centerline
Mark for beginning
of sewing
Button
holder plate
Button
67
EN
4 Align the marks on the fabric with the marks
on the presser foot, and then lower the
presser foot lever.
5 Lower the buttonhole lever behind the tab on
the buttonhole foot, as shown.
6 Lightly hold the end of the upper thread, and
then begin sewing.
* Sew the buttonhole by pressing the start/stop button or
stepping on the foot controller.
* Once sewing is completed, the machine automatically
sews reinforcement stitches, then stops.
7 Use the included buttonhole cutter to cut the center,
making sure not to cut the stitches.
* Putting a marking pin in the bar-tack area helps prevent the bar-
tack from being cut by the buttonhole cutter.
Caution
When cutting buttonholes with the included buttonhole cutter, do not place your
fingers or hands in front of the cutter.
Doing so could cause injuries to your hand.
Marks on
presser foot
Pass thread under presser foot.
Mark for begin-
ning of sewing
Centerline position
Buttonhole
lever
Buttonhole
lever
Tab
68
Shortening jeans
For video tutorial, visit http://www.toyotaoekakisewing.com
Use the Gliding foot to sew fabric of varying thicknesses, especially when hemming jeans.
1 From the operation panel, select stitch number 1 (straight stitch (center)).
* Check that the OEKAKI (free-motion embroidering) button is not lit.
* Refer to “Selecting the stitch” (page 44).
2 Select a stitch length between “3.0” and “4.0” (recommended).
* Refer to “Selecting the stitch length” (page 46).
Maximum thickness of denim when sewing in the utility stitching mode
Up to 12 layers of soft denim (12 oz)
Up to 9 layers of soft denim (14 oz)
Up to 9 layers of hard denim (12 oz)
Note
Do not sew without placing fabric under the presser foot.
Doing so could damage the presser foot.
3 Press the (needle up/down) button to raise the needle.
Caution
The thickness of the layers must not exceed 8 mm. Do not force fabric layers under the
presser foot.
Doing so could break the needle and cause injuries.
Caution
Use this presser foot only with stitch number 1 (straight stitch (center)).
Not doing so could cause the needle to hit the presser foot and break, which may result in
injuries.
Tip
OEKAKI button
not lit
Suitable stitch
1
Presser foot to be used
Gliding
foot
Needle to be used
No. 18/110
69
EN
4 Try on the jeans, and then fold up the legs at the new
hemline, right side to right side.
5 Measure 4 cm up from the hemline and draw a line
with a suitable marker.
6 Turn the jeans inside out to the wrong side, and then
cut along the 4 cm line.
7 Fold up 2 cm of fabric, iron the fold line, and then fold
over another 2 cm of fabric and iron in place.
If the inside leg seam is very bulky, trim away the seam allowance in
the first 2 cm fold.
Tip
Hemline
Right
side
Wrong side
Right
side
Wrong
side
4 cm
Wrong
side
2 cm
First fold
line
Second
fold line
2cm
70
8 Steam iron the side seam areas.
If the side seam areas are very bulky, flatten them with a wooden
mallet, etc., so that the seam can be easily sewn.
9 Remove the extension table (accessory box), and
then pull the jeans hem over the free arm as shown in
the illustration.
10 Sew around the jeans hem, starting about 2 cm in
front of the inside leg seam (refer to the illustration).
Secure the beginning and end of the stitching with a
few reverse stitches.
Tip
Caution
Do not sew reverse stitches over the seam areas.
Doing so could break the needle and cause injuries.
Wrong
side
Right side
Extension table
Free arm
Beginning of
sewing
2 cm
Seam area
71
EN
72
Features of OEKAKI (free-motion embroidering)
O = formal prefix, E = picture, KAKI = to draw
OEKAKI was derived from the Japanese word “to draw”. We wanted to bring you a sewing machine which helps
you create special, unique and personal projects while having fun.
Since the feed dog is lowered during OEKAKI (free-motion embroidering) mode, the fabric can be freely
moved.
In OEKAKI (free-motion embroidering) mode, the stitch width can be adjusted by how much the foot controller
is pressed.
* Lightly stepping on the foot controller selects a narrow stitch width; stepping further on the foot controller selects a
wider stitch width. Slightly releasing the foot controller selects a narrower stitch width.
When the foot controller is connected, the sewing machine cannot be started by pressing the start/stop
button. At the end of sewing, the machine can be stopped by pressing the start/stop button.
In OEKAKI (free-motion embroidering) mode, the sewing speed cannot be adjusted with the foot controller as
in utility stitching mode. For details on changing the sewing speed, refer to page 47.
In OEKAKI mode, the reverse sewing button cannot be used.
8 Basics of OEKAKI (free-motion embroidering)
Caution
Stitching
Stitch width
Narrow NarrowWide
Foot
controller
operation
73
EN
Relationship between the needle, thread and fabric in OEKAKI
mode, and adjusting the thread tension
The quality of the sewing finish will improve if the needle and thread are selected to match the type of fabric used.
Follow the recommendations in the table below.
When purchasing any needles not included as accessories, check that they are specified as home-use
sewing machine needles.
Use the same type of threads for the upper and lower threads.
The larger the needle number, the thicker the needle. The larger the thread number, the thinner the thread.
It may be necessary to adjust the upper thread tension according to the fabric, thread and needle
combination. (Refer to page 88.)
<Selecting a needle suitable for the thread>
Pass the thread to be used through the eye of the needle, and then hold both
ends of the thread to give the thread slack so that the needle slides along it, as
shown.
If the needle does not catch, the needle and thread are a good combination.
Since a needle that is too thick for the thickness of the thread will result in poor-
quality stitching, select the needle with the smallest number possible, which will
not catch on the thread.
If the needle frequently catches on the thread or does not slide along it, stitching
of poor quality will be produced. In this case, select a needle with a different
number or a different type of thread.
Thin fabrics Normal fabrics
Relationship between the needle,
thread and fabric
Needle
No. 11/75 No. 14/90
In OEKAKI mode, do not use needle no. 18/110 or the ball point needle (knit needle).
Refer to “Selecting a needle suitable for the thread”, and then select a needle and thread.
Thread
Fabric
Be sure to attach stabilizer to medium to medium-thick fabrics.
Check that the stabilizer is compatible with the fabric. Sew trial stitches before sewing in
OEKAKI (free-motion embroidering) mode.
Reference
thread tension
Upper
thread
tension
dial
Set the upper thread tension dial to a setting between “-1” and “-3”, making sure that the
lower thread is not visible from the top of the fabric.
-1 – -3
Tip
-
2
-
1
-
3
Thread
Needle
74
OEKAKI (free-motion embroidering) preparations
1 Change the presser foot to the embroidering foot.
Remove the presser foot and the presser foot holder.
Position the pin of the embroidering foot above the needle
clamp screw, and align the clamp in the lower-left of the
embroidering foot with the presser foot holder clamp screw.
2 Secure the embroidering foot.
While holding the embroidering foot straight with your right
hand, tighten the presser foot holder clamp screw with the
needle plate screwdriver in your left hand.
9 Sewing (free-motion embroidering)
Caution
Before changing the presser foot, use the main power switch to turn off the sewing
machine.
Not doing so could cause injuries.
Caution
Firmly tighten the screw with the included screwdriver, and check that the needle does
not hit the presser foot.
If the screw is loose, the needle will hit the presser foot and break or bend, which could cause
injuries.
Clamp
Pin
Needle clamp screw
Presser foot holder
clamp screw
Embroidering foot
Presser foot
holder clamp
screw
75
EN
3 Lower the feed dog.
Lift up the presser foot lever, and then slide the drop feed
lever at the back of the machine to (to the left as seen
from the back) to lower the feed dog.
* If it is difficult to switch the drop feed lever, lower the needle,
and then try again.
4 Connect the foot controller.
The foot controller adjusts the stitch width during OEKAKI (free-motion embroidering).
* In OEKAKI mode, the sewing machine will not operate if the foot controller is not plugged in. If the start/stop button is
pressed, instead of starting the sewing machine, error code “F9” appears.
<Notes on the stitch width>
Lightly stepping on the foot controller selects a narrow stitch width; stepping further on the foot controller selects
a wider stitch width. Slightly releasing the foot controller selects a narrower stitch width.
Caution
Be sure to use the main power switch to turn off the sewing machine before
connecting the foot controller.
Not doing so could cause injuries.
Tip
Drop feed lever
Up Down
Drop feed lever
(as seen from the
back of the sewing
machine)
Stitch width
Narrow NarrowWide
Foot
controller
operation
76
5 Switch to OEKAKI mode.
Turn on the sewing machine, and then switch to OEKAKI
(free-motion embroidering) mode by pressing the
(free-motion embroidering) button so that it lights up in
green.
* If the button is pressed again, it will go off and the sewing
machine will switch to utility stitching mode.
6 From the operation panel, select stitch number A1 or A2.
Press the function button until the LED lights up, and then press the (setting) buttons to
set the stitch number to A1 or A2.
* The stitch number appears in the LED display.
<Stitches that can be used>
* When sewing zigzag stitches from a left needle entry point, the stitch width changes with the left side as the
reference.
* When sewing zigzag stitches from a center needle entry point, the stitch width changes with the center as the
reference.
7 Position the fabric under the presser foot, and
then lower the presser foot lever.
No. Application Presser foot
A1
Zigzag sewing from a left
needle entry point
Embroidering foot
A2
Zigzag sewing from a center
needle entry point
OEKAKI
button
Presser
foot lever
77
EN
8 Lightly place your hands on the fabric to guide it
and sew.
* Lightly step on the foot controller to begin sewing.
* Release the foot controller to stop sewing.
In OEKAKI mode, the fabric can be moved with the presser foot
lowered.
* To change the sewing speed, press the (function) button until the (sewing speed) LED lights
up, and then change the setting.
* While the stitch width can be adjusted by pressing the foot controller, the maximum stitch width can also be
changed. To change the maximum setting, press the (function) button until the (stitch width)
LED lights up, and then change the setting.
Tip
Caution
Do not touch moving parts such as the
needle.
Doing so could cause injuries.
Caution
In OEKAKI mode, feed the fabric according to the sewing speed.
Feeding the fabric faster than the sewing speed could break the needle and cause injuries.
Do not pull the fabric excessively while sewing.
Doing so could break the needle and cause injuries.
Do not touch the top of
the presser foot.
78
Practicing free-motion embroidering
Use the included starter kit to practice free-motion embroidering.
Preparation
Iron the stabilizer onto the wrong side of the fabric.
STEP 1 (Practicing sewing straight stitches)
For video tutorial, visit http://www.toyotaoekakisewing.com
Let’s try straight stitch sewing.
1 Lightly step on the foot controller to begin sewing.
* Since the stitching will become a zigzag if the foot controller is
pressed too much, lightly step on the foot controller.
If it is difficult to adjust the foot controller, set the stitch width to
“0”. The needle will not move back and forth, making it easy to
sew straight stitches.
2 Move the fabric with your hands to follow the outlines of the drawings.
3 Sew by moving the fabric slowly in all directions (forwards, backwards and sideways).
When drawing the circle using a straight stitch, move the fabric in a circular motion.
Tip
Tip
Fabric / top layer
(wrong side)
Stabilizer
Sticky side
79
EN
STEP 2 (Practicing sewing shapes)
For video tutorial, visit http://www.toyotaoekakisewing.com
Let’s try drawing an easy shape using the straight stitch.
1 Begin sewing along the outline of the drawing.
2 Guide the fabric with your hands.
3 Follow the direction arrows in the drawings below.
* For help with practicing OEKAKI (free-motion embroidering), watch the videos on the website.
http://www.toyotaoekakisewing.com
80
STEP 3 (Practicing adjusting the stitch width)
For video tutorial, visit http://www.toyotaoekakisewing.com
By practicing several times, we can gain a better understanding of how the stitch width is adjusted by stepping
on the foot controller and moving the fabric.
1 From the operation panel, select stitch number A1 or A2.
2 While slowly moving the fabric, lightly step on the foot controller to begin sewing.
3 Gradually press the foot controller further to
increase the stitch width, according to the outlines of
the drawings.
4 After fully pressing down the foot controller, gradually release it to reduce the stitch width.
5 Repeat steps 3 to 4.
81
EN
Notes on the stitch width
Operating the foot controller
Lightly stepping on the foot controller selects a narrow stitch width; stepping further on the foot controller
selects a wider stitch width. Slightly releasing the foot controller selects a narrower stitch width.
Moving the fabric
Faster movement creates a rough finish, and slower movement creates a smooth finish.
Faster movement Slower movement
Stitch width
Narrow NarrowWide
Foot
controller
operation
82
STEP 4 (Practicing sewing characters)
For video tutorial, visit http://www.toyotaoekakisewing.com
Let’s draw letters with zigzag stitches.
1 Start sewing from the center, enlarging the
circle, then sewing back to the center again.
2 While lightly stepping on the foot controller,
slowly move the fabric to follow the outline.
3 Press the foot controller further to increase
the stitch width.
4 Gradually release the foot controller.
5 While lightly stepping on the foot controller,
move the fabric horizontally.
* For help with practicing OEKAKI (free-motion embroidering), watch the videos on the website.
http://www.toyotaoekakisewing.com
83
EN
84
Tacking
For video tutorial, visit http://www.toyotaoekakisewing.com
Tacking (temporary stitching) can be sewn with the sewing machine to prevent overlapping layers of fabric from
becoming misaligned.
1 Follow steps 1 through 5 in “Sewing (free-motion embroidering)” (refer to page 74).
2 From the operation panel, select stitch number A3.
Press the function button until the LED lights up,
and then press the (setting) buttons to set the
stitch number to A3.
* The stitch number appears in the LED display.
<Stitches that can be used>
3 Adjust the upper thread tension.
Set the upper thread tension dial to “-1”.
4 Position the fabric under the presser foot, and
then lower the presser foot lever.
5 Lightly guide the fabric with your hands, and then step on the foot controller.
* When stitch number A3 is selected, pressing the foot controller only sews one stitch. Only one stitch is sewn, even if
you keep the foot controller pressed down.
No. Application Presser foot
A3 Tacking (left needle position)
Embroidering foot
Presser
foot lever
85
EN
6 Move the fabric 1 to 2 cm in the direction that the
tacking will be sewn.
7 Repeat steps 5 to 6 to sew the tacking.
8 Switch back to utility stitching mode, sew the
necessary stitching, and then pull out the tacking
thread.
Tacking
1 – 2 cm
Edge of fabric
Intended
sewing line
86
Sewing thick or thin fabrics
Sewing thick fabric
When sewing thick fabric from the edge, the presser foot may be angled and
unable to feed the fabric.
Under the presser foot, place fabric or thick paper of the same thickness as
the fabric that you wish to sew.
Sewing thin fabric
When sewing thin fabric, sometimes the fabric puckers or is not fed correctly.
In this case, the fabric can be sewn more easily if tissue paper is placed
under it.
* After sewing, carefully remove the paper.
Sewing tube-shaped fabrics
1 Pull out the extension table in the direction of
the arrow.
2 Sew tube-shaped fabrics, such as trousers or
sleeves, by pulling them over the machine
free arm as shown in the illustration.
10 Special sewing tips
Fabric or thick
paper
Fabric
being
sewn
Thin
paper
Extension table
Free arm
87
EN
Sewing leather and vinyl
Using the non stick foot
Use this presser foot when sewing hard-to-feed fabric, such as leather
and vinyl, to improve feeding.
Sewing equally spaced lines of stitching
Using the quilting guide
This is useful for sewing equally spaced lines of stitching, such as in
quilting.
1 Insert the quilting guide under the spring plate
on the shank.
* Adjust the quilting guide to the correct position by moving it
sideways.
2 Draw the first line with a suitable marker, and
then sew. For the second line, simply sew
following the stitching of the first line with the
guide.
* The interval between the lines of stitching can be adjusted
by moving the guide in the direction of the arrow.
Caution
Before inserting the quilting guide, use the main power switch to turn off the sewing
machine.
Not doing so could cause injuries.
Non stick foot
Quilting guide
Hole in presser
foot holder
88
Adjusting the thread tension
Adjustment method for the upper thread tension.
If the tension does not change, even after the upper thread tension is adjusted, thread the upper thread and
lower thread again.
When using thread with a strong twist, selecting a lower upper thread tension (-3 to -2) may reduce skipped
stitches.
Upper thread is tight. Upper thread is loose.
Reduce the upper thread tension. Increase the upper thread tension.
Tip
89
EN
90
When the fabric cannot be removed from the sewing machine
If the fabric cannot be removed from the sewing machine, the thread may have become entangled under the
needle plate. In this case, do not pull on the fabric with excessive force. Doing so could cause damage.
1 Raise the presser foot and needle.
If the needle is in the fabric, turn the handwheel
towards the back of the machine to get the needle
out of the fabric, then cut the thread close to the
needle.
2 Remove the bobbin case cover.
3 Cut out the tangled thread.
* If the fabric can be removed:
Go to “Feed dog and hook maintenance” (page 98).
* If the fabric cannot be removed:
Go to step
4.
Caution
For safety, use the main power switch to turn off the sewing machine, and then remove
the power plug from the outlet.
Not doing so could cause injuries.
Caution
Hand-
wheel
Bobbin case
cover
91
EN
4 Use the included needle plate screwdriver to
remove the two needle plate screws.
5 Slightly lift up the needle plate, cut out the
tangled thread, and then remove the needle
plate.
6 Remove the bobbin case, and then remove any thread around the hook and feed dog.
* Refer to “Feed dog and hook maintenance” (page 98).
* If the fabric still cannot be removed, contact your retailer.
Caution
Carefully work around pointed parts to avoid cutting your fingers.
Not doing so could cause injuries.
Needle
plate
Needle plate screwdriver
Needle plate screws
Needle
plate
92
When the sewing machine is operating incorrectly
What is the problem?
Check the following possibilities before contacting the service center for repairs.
11 Troubleshooting
Trouble Cause Countermeasure Page
Machine does
not operate
The power plug is not inserted. Correctly connect the power plug. 22
The sewing machine has been turned
off with the main power switch.
Turn on the sewing machine. 22
Thread is tangled in the race. Clean the race. 90, 98
There is a broken needle in the race.
The thread winding spindle has been
pushed to the right.
Slide the thread winding spindle to the
left.
31
The presser foot lever is still raised. Lower the presser foot lever. 26
The start/stop button is pressed while
the foot controller is connected.
Disconnect the foot controller, or start
the sewing machine with the foot
controller.
18
Very noisy
Very slow
There is lint or dust in the hook or feed
dog.
Remove the lint or dust. 98
Needle cannot
be threaded
The needle is not at the correct position. Press the needle up/down button to
raise the needle.
16
The needle threader hook does not pass
through the eye of the needle.
Press the needle up/down button to
raise the needle.
16, 38
The needle is incorrectly installed. Correctly install the needle. 24
The needle is bent. Replace the needle. 23
Needle breaks The needle is incorrectly installed. Correctly install the needle. 24
The needle clamp screw is loose. Firmly tighten the screw. 24
The needle is too fine for the fabric. Use a needle suitable for the fabric. 52, 73
The upper thread tension is too tight or
too loose.
Adjust the upper thread tension. 88
The bobbin case is incorrectly
positioned.
Correctly position the bobbin case. 100
The selected presser foot is not suitable
for the stitch.
Select a suitable presser foot for the
stitch.
48
93
EN
Upper thread
breaks
The upper and lower threads are
incorrectly threaded.
Correctly thread the upper and lower
threads.
32, 34
The thread is tangled in the bobbin case
or race.
Remove lint from the feed dog and
race.
98
The thread is too thin for the thickness of
the needle.
Use thread suitable for the thickness of
the needle.
52
The upper thread tension is too tight or
too loose.
Adjust the upper thread tension. 88
The needle is bent. Replace the needle. 23
The point of the needle is blunt/worn
away.
The needle is incorrectly installed. Correctly install the needle. 24
The thread is old. Use new thread.
Lower thread
breaks
The lower thread is incorrectly threaded. Correctly thread the lower thread. 32
Stitches not
formed / Only
needle holes in
fabric
The upper thread passes from behind
the needle to the front.
Pass the upper thread from the front of
the needle to the back, or use the
needle threader.
37, 38
Thread with a strong twist is being used. Change the thread, or set the upper
thread tension to a setting between -3
and -2.
52
The thread is too thin for the thickness of
the needle.
Use thread suitable for the thickness of
the needle.
52
Stitches
formed, but
easily pulled
out
Reverse stitches are not used. Sew reverse stitches. 55
The upper thread tension is incorrect. Adjust the upper thread tension. 88
Lower thread
not taken up
The needle is bent. Replace the needle. 23
The needle is incorrectly installed. Correctly install the needle. 24
Fabric not fed The feed dog is lowered. Use the drop feed lever to raise the
feed dog.
75
There is lint in the feed dog. Remove lint from the feed dog and
race.
98
The stitch length is set to “0”. Adjust the stitch length to an
appropriate setting.
46
Synthetic leather or vinyl is being sewn. Use the non stick foot. 7
Sewing speed
not changing
You are trying to use the foot controller
to change the sewing speed in OEKAKI
(free-motion embroidering) mode.
In OEKAKI mode, use the operation
panel buttons to change the “sewing
speed” setting.
47
Trouble Cause Countermeasure Page
94
Skipped
stitches
The needle is incorrectly installed. Correctly install the needle. 24
The needle is bent. Replace the needle. 23, 24
The needle and thread are not suitable
for the fabric.
Sew with a needle and thread suitable
for the fabric.
52, 73
The upper thread is incorrectly
threaded.
Correctly thread the upper thread. 34
Stabilizer is not used in OEKAKI mode. Attach stabilizer. 78
Fabric wrinkles/
puckers
The upper thread tension is too tight. Adjust the upper thread tension. 88
The upper and lower threads are
incorrectly threaded.
Correctly thread the upper and lower
threads.
32, 34
The needle is too thick for the fabric. Use a needle suitable for the fabric. 52, 73
The needle is burred or bent. Replace the needle. 24
Stretch fabric is being sewn. Use the ball point needle.
Select a stitch and feed suitable for
stretch fabric.
48
Stabilizer is not used in OEKAKI mode. Attach stabilizer, especially with thin or
stretch fabrics, fabrics with a coarse
weave, or fabrics that often cause
pattern shrinkage.
78
Too much
lower thread
showing on
right side of the
fabric
The lower thread is incorrectly threaded. Correctly thread the lower thread. 32
The upper thread tension is too tight. Adjust the upper thread tension. 88
The bobbin is not correctly inserted in
the bobbin case.
Correctly insert the bobbin in the
bobbin case.
32
The specially designed bobbin is not
being used.
Use a specially designed bobbin. 7
A metal bobbin is being used.
Too much
upper thread
showing on
wrong side of
the fabric
The upper and lower threads are
incorrectly threaded.
Correctly thread the upper and lower
threads.
32, 34
The tension of the upper thread is too
loose
Adjust the upper thread tension. 88
The upper thread is incorrectly
threaded.
(not threaded through the thread guide)
Correctly thread the upper thread. 34
Thread
entangled
under fabric
The thread has come out of the take-up
lever.
Raise the presser foot, and then
correctly thread the sewing machine.
34
The upper thread is incorrectly
threaded.
The lower thread has come out of the
groove in the bobbin case.
Correctly thread the lower thread. 32
Trouble Cause Countermeasure Page
95
EN
If the above countermeasures do not solve the problem, contact the service center as described in your warranty.
When calling for service, please note the MODEL and SERIES that are inscribed on the back of your sewing
machine.
Unable to
adjust stitch
width in
OEKAKI mode
The foot controller is disconnected. Connect the foot controller. 18
The OEKAKI (free-motion embroidering)
button is not lit.
Press the OEKAKI button so that it
lights up.
76
Stitch number A3 is selected in OEKAKI
mode.
Select stitch number A1 or A2.
(A3 is the tacking stitch.)
76
From the operation panel, the stitch
width has been set to “0” or a low
setting.
Increase the stitch width setting, or
select an appropriate setting.
77, 78
Trouble Cause Countermeasure Page
96
When an error code appears
If an incorrect operation was performed, an error code between F1 and F9 appears in the LED display. Try again
with the correct procedure.
LED display Cause Countermeasure
F1
This appears and the sewing machine
stops when the motor is being overloaded,
for example, when the fabric is too thick.
Try again with fabric of a suitable
thickness.
F2
This appears when the sewing machine is
started with the start/stop button or the foot
controller while the presser foot is raised.
Lower the presser foot lever.
F3
This appears when the buttonhole lever is
not lowered to the buttonhole foot even
though a buttonhole stitch is selected.
Lower the buttonhole lever to the
buttonhole foot.
F4
This appears when a stitch other than a
buttonhole stitch is selected and the
buttonhole lever has been lowered and the
buttonhole foot is still attached.
Replace the presser foot to one suitable for
the stitch, and then raise the buttonhole
lever.
F5
This appears and the sewing machine
suddenly stops when the foot controller
connector is plugged into the jack while the
sewing machine is running.
With the sewing machine stopped, plug the
foot controller connector into the jack.
F6
This appears and the sewing machine
suddenly stops when the foot controller
connector is unplugged from the jack while
the sewing machine is running.
With the sewing machine stopped, unplug
the foot controller connector from the jack.
F7
This appears and the sewing machine
suddenly stops when the thread winding
spindle is slid to the right while the sewing
machine is running.
Return the thread winding spindle to the
standby position (left).
F8
This appears and the sewing machine
suddenly stops when the thread winding
spindle is slid to the left while the bobbin is
being wound.
Move the thread winding spindle while the
sewing machine is stopped.
97
EN
* Although the above code will disappear after 2 to 3 seconds, the necessary countermeasure should be
performed.
Note
If the problem is not resolved after the appropriate countermeasure is performed, stop using
the sewing machine and contact your retailer.
A code between E1 and E9 appearing indicates that the sewing machine has malfunctioned.
Immediately stop using the sewing machine and contact your retailer.
F9
This appears when any of the following
incorrect operations are performed. (The
sewing machine does not operate.)
1 You try to start the sewing machine with
the start/stop button while the foot
controller is connected.
1 When the foot controller is connected,
start the sewing machine with it.
2 In OEKAKI mode, the start/stop button
or reverse sewing button is pressed.
2 In OEKAKI mode, use the foot
controller.
3 The reverse sewing button is pressed
while a buttonhole stitch is selected.
3 Use the start/stop button or foot
controller with buttonhole stitches.
4 While the bobbin is being wound, the
needle up/down button or reverse
sewing button is pressed.
4 When winding the bobbin, use the start/
stop button or foot controller.
P0 – 9
or PF
This appears when an incorrect operation
was performed with the sewing machine
turned on.
Since the sewing machine is in service
mode, turn it off, then on again.
LED display Cause Countermeasure
98
Feed dog and hook maintenance
Note
Do not use detergent, bleach, benzine, thinner or chemically treated cloths. Doing so could cause
discoloration or cracking.
* If the thread becomes entangled in the bobbin case or race, or if the bobbin case moves out of position,
refer to the following procedure.
Cleaning and maintenance must not be made by children without proper supervision.
Cleaning
1 Remove the needle, presser foot, bobbin case
cover and bobbin.
Use the included needle plate screwdriver to turn the two
needle plate screws counterclockwise and remove them.
* For details on removing the needle, refer to page 24.
For details on removing the presser foot, refer to page 25.
2 Remove the needle plate.
12 Maintenance and storage
Caution
For safety, use the main power switch to turn off the sewing
machine, and then remove the power plug from the outlet.
Not doing so could cause injuries.
Main power switch
Power plug
Needle
plate
Needle plate screwdriver
Needle plate screws
Needle
plate
99
EN
3 Lift up the bobbin case so that part a is moved past
part b on the sewing machine, as shown.
4 Pull out the bobbin case in the direction of the arrow
to remove it.
Note
Do not pull with excessive force. Doing so could cause the
bobbin case to be scratched.
* If the bobbin case cannot be pulled out, repeat the procedure
starting with step
3.
5 Brush off any lint or dust on the feed dog and race,
and then clean them with a soft cloth.
Caution
When cleaning the race, do not touch
the sharp pointed part.
Doing so could cause injuries.
a
b
Feed dog
Hook
Hook
Pointed
100
Installing the bobbin case
1 Position the bobbin case so that part c on the bobbin
case is in front of part d on the sewing machine.
2 With the bobbin case tilted to the left, insert the left
side of the bobbin case into the race, as shown.
3 Insert the right side of the bobbin case into the hook
so that part a on the bobbin case is to the left of part b
on the sewing machine.
c
d
Left side of bobbin case
Right side of
bobbin case
a
b
101
EN
4 Make sure that the bobbin case is fully installed in the race.
f
Note
If the bobbin case is unstable when the handwheel is turned towards yourself two or three times, or
if it has been incorrectly installed as described above on the right, repeat the procedure starting with
step
1.
5 Install the needle plate with mark c on
the bobbin case positioned to the left of
part e on the needle plate (as shown in
the illustration at the right).
Correct Incorrect
The entire bobbin case fits into the hook so that
the edge of the hook is visible.
Part a on the bobbin case is to the left of part b on
the sewing machine.
The right side of the bobbin case covers the edge
of the hook and the bobbin case is tilted.
Part a on the bobbin case is to the right of part b on
the sewing machine.
Edge of hook
ab
ab
e
c
Needle
plate
102
6 Use the included needle plate
screwdriver to turn the two needle plate
screws clockwise and install them.
7 Install the presser foot and the needle.
8 Turn the handwheel to check that the needle correctly enters the hole in the needle plate.
* If the bobbin case is not installed correctly, the handwheel does not turn smoothly. If this occurs, remove the needle
plate and bobbin case, and install them again.
* For details on installing the needle, refer to page 24.
For details on installing the presser foot, refer to page 26.
Caution
When checking that the needle correctly enters the hole in the needle plate, do not
perform any operation other than turning the handwheel.
Doing so could cause injuries.
Needle plate screws
Needle
plate
103
EN
Storage precautions
Storing
Observe the following precautions when storing. Not doing so could cause damage, discoloration or breakage.
Do not store in a location exposed to humidity or excessive dust.
* We recommend storing the sewing machine covered with the included soft cover.
Do not store in a location exposed to direct sunlight or near a heater.
Do not store on an unstable surface.
Do not store upside down or laying down.
Do not store in a location exposed to smoke or steam.
Note
Do not use the sewing machine for industrial purposes. Doing so could cause damage from being
overloaded.
The sewing machine is not guaranteed for use in industrial applications.
Due to product quality improvements, the specifications or appearance of this machine may change without
notice.
The contents of this Instruction Manual may not be duplicated without permission.
The contents of this Instruction Manual are subject to change without notice.
Caution
Do not store the sewing machine within the reach of children.
They could touch the needle and be injured.
104
Recycling
We are committed to the protection of the environment. We strive to minimize the environmental impact of our
products by continuously improving product design and our manufacturing methods.
At the end of its life, please dispose of this product and packaging in an environmentally responsible way.
The crossed-out wheelie bin symbol featured above and on the product’s data-plate means that this product falls
under the scope of the E.U. “Waste Electrical and Electronic Equipment” (WEEE) directive and “Restriction of the
Use of Certain Hazardous Substances in Electrical and Electronic Equipment” (ROHS) directive and should not
be disposed of with your household waste. At end of life, you must ensure that this product is disposed of in
accordance with national and local legislation and that it is sorted as Category 2 “Small Domestic Appliances
WEEE. You may be liable under local and national laws for improper disposal of this product. Please consult the
web, or a competent national or local body, for the return and collections systems available to you and the
locations of your nearest recycling points. If you purchase a new product direct from us, we will take your old
product back, irrespective of the brand, if it is a like-for-like sale.
As an individual, you can make a positive impact on reuse, recycling and other forms of recovery of WEEE. This
will reduce use of landfill and minimize the environmental impact of the products you use.
Hazardous substances in electronic and electrical products can have a harmful impact on human health and on
the environment.
Servicing double-insulated products (230V–240V)
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means
are provided on a double-insulated product nor should a means for grounding be added to the product. Servicing
a double-insulated product requires extreme care and should only be done by qualified service personnel with
knowledge of the system under his or her responsibility. Replacement parts for a double-insulated product must
be identical to those parts in the product. The symbol is marked on the double-insulated product.
13 Others
DO NOT THROW AWAY!
EU ONLY
105
EN
Specifications
Model OEKAKI
Hook type Horizontal
Needle Home-use sewing machine needle (HA-1)
Bobbin TOYOTA-exclusive plastic bobbin
Maximum stitch length 4 mm
Maximum stitch width 5 mm
Straight stitch needle position Center needle position, left needle position
Sewing machine weight (main unit) 6.5 kg
Sewing machine size Width: 470 mm
Depth: 234 mm
Height: 294 mm
Rated voltage AC220–240 V
Rated frequency 50 Hz
Rated power consumption (LED light
power consumption)
50 W (0.05 W)
Foot Controller
Type 678560-DJE10
Direct-current/Voltage/Electric current DC5V (No electric current)
Web: www.home-sewing.com
Head Office Avenue de l’Industrie 21, Parc Industriel, 1420 Braine-L’Alleud BELGIUM
TEL: +32 (0) 2 387 1817 FAX: +32 (0) 2 387 1995
UK Branch Unit 4, Swan Business Park, Sandpit Road, Dartford, Kent, DA1 5ED UK.
TEL: +44 (0) 1322 291137 FAX: +44 (0) 1322 279214
France Branch
70 chemin de la chapelle Saint Antoine 95300 Ennery, France
TEL: +33 (0) 1 34 30 25 00 FAX: +33 (0) 1 34 30 25 01
Holland Branch Energieweg 14, 2382 NJ Zoeterwoude (Rijndijk), THE NETHERLANDS
TEL: +31 (0) 71 5410251 FAX: +31 (0) 71 5413707
Austria Branch Donaufelder Straße 101/5/1, A-1210 Wien, AUSTRIA
TEL: +43 (0) 1 812 06 33 FAX: +43 (0) 1 812 06 33-11
Imported by / Importé par :
EU ONLY
105

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Toyota OEKAKI50R bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Toyota OEKAKI50R in de taal/talen: Engels als bijlage per email.

De handleiding is 5,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Toyota OEKAKI50R

Toyota OEKAKI50R Gebruiksaanwijzing - Nederlands - 106 pagina's

Toyota OEKAKI50R Gebruiksaanwijzing - Deutsch - 106 pagina's

Toyota OEKAKI50R Gebruiksaanwijzing - Français - 106 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info