English
“IMPORTANT SAFETY INSTRUCTIONS”
When using the sewing machine, basic safety precautions should
always be followed, including the following:
Read all instructions before using.
DANGER – – To reduce the risk of electric shock.
1. The sewing machine should never be left unattended when plugged in. Always unplug the sewing
machine from the electrical outlet immediately after using and before cleaning.
2. Always unplug before relamping. Replace the bulb with same type rated 15 watts.
3. Do not reach for the sewing machine that has fallen into water. Unplug immediately.
4. Do not place or store sewing machine where it can fall or be pulled into a tub or sink. Do not place or
drop into water or other liquid.
WARNING – – To reduce the risk of burns, fire, electric shock, or injury to
persons.
1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or
near children.
2. Use this sewing machine only for its intended use as described in this manual. Use only attachments
recommended by the manufacturer as contained in this manual.
3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it
has been dropped or damaged, or dropped into water. Return this sewing machine to the nearest
authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
4. Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the
sewing machine and foot controller free from the accumulation of lint, dust, and loose cloth.
5. Never drop or insert any object into any opening.
6. Do not use outdoors.
7.Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.
9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.
11. Always use proper needle plate. The wrong plate can cause the needle to break.
12. Do not use bent needles.
13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
14. Switch the sewing machine off (“O”) when making any adjustments in the needle area, such as
threading needle, changing needle, threading bobbin, or changing presser foot, etc.
15. Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when
making any other user servicing adjustments mentioned in this instruction manual.
16. Never operate on a soft surface such as a bed or couch where the air openings may be blocked.
17. Appliance (230-240V) is provided with double insulation. Use only identical replacement parts. See
instructions for servicing Double-insulate Products.
Servicing Double-Insulated Products (230V-240V)
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding
means is provided on a double-insulated product nor should a means for grounding be added to the product
Servicing a double-insulated product requires extreme care and knowledge of the system and should only be
done by qualified service personnel. Replacement parts for a double-insulated product must be identical to
those parts in the product. The symbol is marked on the double-insulated product.
This sewing machine is intended for household use.
SAVE THESE INSTRUCTIONS
UK ONLY IMPORTANT PLEASE READ CAREFULLY
The wires in this mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL BROWN - LIVE (OR ACTIVE)
As the colours of the mains lead of this appliance may not correspond with the coloured markings identifying
the terminals in your plug — PROCEED AS FOLLOWS:
The earth plug pin is unnecessary. As the machine is designed under double insulation structure, the earth
wire is removed from the machine. The wire coloured BROWN must be connected to the terminal marked L
or A or coloured RED. The wire coloured BLUE must be connected to the terminal marked N or coloured
BLACK. Neither core is to be connected to the earth terminal of a three-pin plug.
