485654
19
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
36
37
Operations
Connecting the power cord
1
Insert the power cord connector into
the AC IN socket of the projector.
2
Insert the power cord plug into a wall
or other power outlet.
Turning the power on
1
Remove the lens cap.
Remove the lens cap as shown (if present).
Be sure to remove the lens cap when the power is turned on.
If the cap is left on the projector, it could become deformed
due to heat.
2
Turn on the main power switch.
The ON/STANDBY indicator lights orange, and the
Status indicator lights green indicating standby mode.
3
Press the ON/STANDY button on
the control panel or on the remote
control.
The ON/STANDBY LED lights green and the internal
cooling fan starts.
4
After approximately 10 seconds,
the ON/STANDBY LED ashes
intermittently green.
5
The LAMP1 and LAMP2 LEDs light
green and the ON/STANDY LED
ashes more rapidly.
6
Once the ON/STANDBY, LAMP1 and LAMP2 LEDs are lit
solidly green, the projector is ready for use.
Turning the power on and off
Operations
Control panel
Remote
control
ON/STANDBY STATUS LAMP1 LAMP2
ON/STANDBY STATUS LAMP1 LAMP2
ON/STANDBY STATUS LAMP1 LAMP2
Power cord
connector
(supplied)
CAUTION
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyesight.
Do not block the air intake or exhaust. Doing so could cause a re due to internal overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the bottom of
the unit. Doing so could result in injury and/or damage.
Notes
The rst time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed.
When [Key lock] is [On], the operation buttons of the projector do not work
p.56
.
When [Password] is [On], enter password then the start-up screen is displayed after
the Password entry screen disappears
p.45
.
Do not touch the lens directly with your hand.
If ngerprints or stains are left on the projection lens surface, they may interfere with the
projector’s ability to project images on the screen.
Turning the power off
1
Press the ON/STANDBY button on the control panel or the
remote control.
A message appears on the screen, conrming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.
The screen goes blank, but the internal cooling fan
continues to operate. Then, the projector goes into
standby mode.
During cooling, the ON/STANDBY indicator ashes. While the indicator is ashing, the
power can not be turned back on. However, there is no problem with unplugging the power
cord in this state.
Note
The projector consumes about 5W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
Precaution
If the power cord is unplugged before cooling is complete or the main power is turned
off, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp
overheats, it may fail to light.
Power saving mode
Power saving mode activates the standby condition consuming less power than
Standard mode. Go to the Setting-Setting 2 menu to turn on Power saving mode.
ON/STANDBY STATUS LAMP1 LAMP2
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Toshiba TDP-WX5400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Toshiba TDP-WX5400 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info