497489
26
Verklein
Vergroot
Pagina terug
1/59
Pagina verder
26
8-4-3. Wiring Connection
WARNING
To plug the cable in the plug receptacle, take the
following precaution.
THIS APPLIANCE MUST BE EARTHED.
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLORED
IN ACCORDANCE WITH THE FOLLOWING CODE:
Place your finger on the lower part and push up
to open the screw cap.
(1) Open the screw caps and remove the two screws
securing the front cabinet.
(2) Close the screw caps as behind.
(3) Open the vertical airflow louver horizontally by
hand.
(4) Slightly open the lower part of the front cabinet
then pull the upper part of the front cabinet
toward you to remove it from the rear plate.
Fig. 8-4-6
How to open the screw cap
3
2
2
1
1
4
4
Vertical air flow louver.
Fig. 8-4-5
As the colors of the flexible cord of this appliance
may not correspond with the colored markings, to
identify terminals in your plug, as follows:
Connect BROWN colored core to plug terminal
marked letter L.
Connect BLUE colored core to plug terminal marked
letter N.
Connect GREEN AND YELLOW colored core to plug
terminal marked Earth Symbol
.
The installation of the cables has to be done in such
a way that the basic insulated wires for the infrared
sensor can not be touched.
<How to remove the front cabinet>
L
N
L
N
-LIVE
-NEUTRAL
-EARTH
: Brown
: Blue
: Green and Yow
Taking out the power cord
Cut off the slitted portion in the side face of the
rear panel to take out the power cord. After
this, remove burrs, sharp edges, etc., to
smooth the cut face..
<How to connect the power cord>
(For RAS-07YK-E, RAS-07YK-ES, RAS-10YK-E,
RAS-10YK-ES
only)
For the air conditioner that has no power cord,
connect a power cord to it as mentioned below.
After removing the front cabinet, remove the
terminal cover and the cord clamp.
Connect and secure the power supply cord and
secure the cord clamp and the terminal cover.
Cut the rear panel following the cutting mark and
put the power supply cord through the notch.
Be sure to smooth out the notch with a file, etc.
Slitted portion
Cord clamp
Terminal cover
Screw
Power supply
cord
Terminal block
Earth line
Screw
Screw
L
N
Fig. 8-4-7
<Stripping length of power cord>
NOTE :
Use standard wire only.
Wire type: More than H05-RN-F
Fig. 8-4-8
Earth line
40mm
10mm
10mm
30mm
L
N
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Toshiba RAS-07YK-E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Toshiba RAS-07YK-E in de taal/talen: Engels als bijlage per email.

De handleiding is 10,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info