807536
83
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
83
DE EN
10.4.5 Anti-fouling coating
NOTE! Observe national regulations on the processing, application, use and
disposal of anti-fouling coatings. Follow the manufacturer's instructions and
processing instructions.
General instructions
To keep your Cruise system free of fouling, you can do the following:
Remove the Cruise system from the water after each use and clean it.
Regularly clean all components of the Cruise system that are permanently
below the water surface.
Use an anti-fouling coating.
Cleaning the components under the water surface
Before cleaning work, switch off the Cruise system at the main switch and
secure it against being switched on again by pulling off the switch handle.
Do not use tools with sharp edges or abrasive surfaces that may damage
the Cruise system's paintwork.
Using anti-fouling coatings
When using anti-fouling paints, we recommend that all parts of the
Cruise Systems that are permanently below the water surface are coated.
1. Clean the surfaces of the Cruise system that you want to treat.
NOTE! Do not use abrasives to roughen the surface, otherwise the protective
coating will be damaged.
2. Thoroughly mask the anodes and, if necessary, the motor shaft.
3. Observe the processing instructions and the manufacturer's instructions on
personal protective equipment for the respective anti-fouling coating.
Permitted anti-fouling coatings
International Trilux 33 in combination with primer Primocon Sperrgrund
Hempel Silic One in combination with Hempel Light Primer and Hempel
Silic One Tiecoat
NOTE! Do not use metal-containing anti-fouling coatings e.g.products
containing copper.
11 Errors and troubleshooting
11.1 Error messages and errors
Display Cause Troubleshooting
E02 Stator overtemperature
(motor overheated)
After a short waiting time (approx. 10
minutes), the motor can be operated
slowly. Contact Torqeedo Service.
E05 Motor/propeller blocked Set the main switch to the “OFF”
position. Release the blockage and turn
the propeller one turn further by hand.
Reconnect the motor cable.
E06 Voltage at motor too low Low battery state of charge. If necessary,
the motor can be driven slowly from the
stop position.
E07 Overcurrent at the motor Continue driving with low power. Contact
Torqeedo Service.
E08 Circuit board
overtemperature
After a short waiting time (approx. 10
minutes), the motor can be operated
slowly. Contact Torqeedo Service.
E21 Faulty calibration of
tiller / remote throttle
Set forwards/reverse motion
E22 Magnetic sensor
defective
Set forwards/reverse motion
E23 Value range wrong Set forwards/reverse motion
E30 Motor communication
error; error in the power
supply to the motor
Contact Torqeedo Service;
Check that the main switch is in the “ON”
position.
E32 Tiller communication
error / remote throttle
Check the plug connections of the data
cables and cables.
E33 General communication
error
Check the plug connections and the
cables. Switch the motor off and on again.
E34 Emergency kill switch or
kill switch actuated
Make sure that the cause of the error has
been eliminated, set the emergency kill
switch or the kill switch to the position for
normal operation and restart the system.
83

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Torqeedo Cruise 6.0 FP TorqLink bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Torqeedo Cruise 6.0 FP TorqLink in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2.97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Torqeedo Cruise 6.0 FP TorqLink

Torqeedo Cruise 6.0 FP TorqLink Gebruiksaanwijzing - Nederlands - 92 pagina's

Torqeedo Cruise 6.0 FP TorqLink Gebruiksaanwijzing - Français, Italiano - 92 pagina's

Torqeedo Cruise 6.0 FP TorqLink Gebruiksaanwijzing - Dansk - 92 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info