807535
71
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
71
DE EN
4. Position the connector plugs (1) on the corresponding port of the compo-
nent (2), making sure that the nose of the plug slides into the groove of the
component (3).
5. Screw the connection plug hand-tight.
6. Connect all the data network connectors.
7. Roll up the excess cable and secure it. (e.g. with cable ties).
Power cable
1. Lay the system power cables.
2. Attach the power cables to the designated places according to your plans.
3. Note the minimum bending radius.
4. Make sure that the cables are laid without tension or load.
5. Make sure that the battery main switch is in the "OFF" position and secured
against being switched on again by pulling off the switch handle.
6. Connect the red positive power cable to the positive terminal of the battery,
observing the tightening torque - see connection diagram.
7. Connect the black negative power cable to the negative terminal of the
battery, observing the tightening torque - see connection diagram.
8. Connect the plug connection of the power cables and x them in the desig-
nated place according to your plans.
NOTE! Observe the sequence when disconnecting the power cables, e.g. if you
want to disconnect for storage, see chapter “Storage”.
NOTE! Power cables must not be coiled.
Earth cable
NOTE: If a second earthed on-board power system is available, make sure that
both systems use a common earthing point, see connection diagram.
3
2
1
1. Observe the required cable cross-section of the earth cable.
2. Lay the earth cable according to your diagrams and secure it. Observe the
minimum bending radius of the earth cable used.
3. Position the ground wire (1) on the clamping ring (2) (see Installing the
motor) and install the screw (3). Tighten the screw with 4.5 Nm.
NOTE! For more information on the earth cable, see the corresponding connec-
tion diagram.
Charger unit
DANGER
Danger of injury or death from electric shock. This can result in sever injuries
or death.
Make sure that the charger unit is disconnected from the power source.
1. Lay the charger unit cables according to your diagrams and x them in the
designated places.
2. Connect the red positive cable of the charger unit to the positive terminal of
the battery, observing the tightening torque - see connection diagram.
3. Connect the black negative cable of the charger unit to the negative
terminal of the battery, observing the tightening torque - see connection
diagram.
71

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Torqeedo Cruise 3.0 FP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Torqeedo Cruise 3.0 FP in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2.97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Torqeedo Cruise 3.0 FP

Torqeedo Cruise 3.0 FP Gebruiksaanwijzing - Nederlands - 92 pagina's

Torqeedo Cruise 3.0 FP Gebruiksaanwijzing - Français, Italiano - 92 pagina's

Torqeedo Cruise 3.0 FP Gebruiksaanwijzing - Dansk - 92 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info