SPARE PARTS FOR TSS-60P
REF. NR. DESCRIPTION
7 CARBON BRUSH 406770
9 SWITCH 406771
10 SPEED CONTROL PLATE 406772
13 DUST EXTRACTION FACILITY 406779
14 INDUCER
15 STATOR 406773
17 ROTOR 406774
19 CENTRAL SUPPORT
21 SLIDING PLATE 406769
22 BALANCE WEIGHT
23 GEAR WHEEL 406775
26 ROLLER
27 RECIPROCATING BAR
29 FIXED BAR
30 SLIDING BEARING A
32 BLADE HOLDER
35 SLIDING BEARING B
38 PENDULAR SPRING
40 GUIDE WHEEL
41 GUIDE WHEEL SUPPORT
45 GUIDE WHEEL PIN
53 SAFETY GUARD 406776
Toledo 39
Product: Toledo Jigsaw
Type TSS-60P, article number 826055
Toledo, Genemuiden, The Netherlands
Sound pressure level L
pa
85 dB(A)
Sound power level L
wa
98 dB(A)
Vibration (
-
a
w
) 2,5 m/s
2
SERIAL NUMBER
The serial number on the machine consists of the
following elements.
Serial nr.
CAREFULLY READ THE INSTRUCTIONS
BEFORE YOU USE THE JIGSAW!
1. KNOW YOUR TOOL
Observe the instructions for maintenance to ensure
your apparatus always operates properly. Before at-
tempting to operate the apparatus, familiarise yourself
with the controls and make sure you know how to stop
it quickly in an emergency. Save this user’s manual and
the other documents supplied with this apparatus for
future reference.
2. SPECIAL SAFETY INSTRUCTIONS
1. CHECK THE FOLLOWING POINTS:
- Do the voltage of the engine and the engine safe
guard, if any, correspond to the mains voltage;
- Are the mains lead and the mains plug in a good con-
dition: solid, without any loose ends or damage;
- If the saw blade is missing any teeth, or if it shows
any cracks, it must be replaced immediately.
- Is there enough space under the workpiece for
the up and down going sawblade, so the sawbla-
de kan not reach the floor or worktable.
2. Never put sideward pressure on the blade. This
may cause the blade to break.
3. Be careful when cutting wood with knots, nails or
cracks in it and/or dirt on it, as these can cause the
blade to get stuck.
4. Never leave the jigsaw unattended.
5. Make sure the teeth of the saw blade point upwards.
Before connecting the tool to the power sup-
ply make sure the trigger switch is not locked
in the “ON” position.
USING THE MACHINE
1. Use clamps or a vice to hold the work.
2. Never remove wood chips and suchlike that are
close to the saw blade with your hands. When
wood chips get stuck between fixed and/or moving
parts, stop the tool before removing them.
3. Make sure the jigsaw runs without load (i.e. is not
in contact with the work) when you switch on the
tool.
4. The saw blade is one of the most important com-
ponents of your jigsaw. Selecting the right material,
teeth, as well as correct fitting of the blade not only
prolongs the life of the blade, but also prevents it fr-
om breaking and cracking with all its consequences.
5. Be careful when cutting scrap wood. As the quality
of the cut is not important, the user tends to be less
concentrated, not to check the wood for nails,
knots or other irregularities, and to put undue
pressure on the saw.
6. Never cut wood that is thicker than the length of
the saw blade.
7. Do not touch metal parts on the jigsaw when cut-
ting in walls or floors where wiring is located. Hold
the tool with both hands by its plastic handle to
avoid touching metal parts through which electrici-
ty may pass when you unintentionally cut through
wiring.
8. Switch off the tool and wait until the blade has stop-
ped completely before moving the saw away from
the work or putting it down.
9. Avoid the use of long extension-cables.
10. This jigsaw is fitted with a plastic safety guard. Make
sure it is in place when cutting.
