Handleiding Timex W223 (pagina 8 van 117) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks)

466713

Verklein

Vergroot

Pagina terug

1/117

Pagina verder

ENGLISH 222-095001-03

SETTING THE DATE

1. PULL the crown out to the 1st position “B”.

2. Turn the crown clockwise to set the date. *If the date is set between the

hours of around 9:00 PM and 1:00 AM, the date may not change on the

following day.

3. After the date has been set, push the crown back to the normal position “A”.

OPERATING THE CHRONOGRAPH FUNCTION (WILL MEASURE UP

TO 1 HOUR)

1. PRESS pusher “A” to start timing.

2. PRESS pusher “A” to stop timing.

3. PRESS pusher “B” to reset.

RECALIBRATING THE CHRONOGRAPH SECOND HAND

(IF IT DOES NOT RETURN TO THE 12 POSITION AFTER RESET

OR AFTER CHANGING THE BATTERY)

1. PULL the crown out to the 2nd position “C”.

2. PUSH pusher “A” to move the Chronograph second hand one increment

forward (holding the pusher in continually will rapidly advance the hand).

3. Once the Chronograph second hand is in the 12 position, PUSH the crown in

to the normal position “A”. The second hand in the sub-dial at the 6 position

will begin to move.

ELAPSED TIME RING

If your watch is equipped with a rotatable outer ring on the face, with numbers

corresponding to minutes, you can use this Elapsed Time Ring to time an

activity from the start, or to mark the ending time for the duration of an activity.

TO TIME AN ACTIVITY FROM THE START:

Set the Start/Stop triangle at the time (hour or minute) when you start the

activity (As shown on the left in the illustration shown below). At completion,

you can see how long the activity took.

TO MEASURE THE TIME REMAINING:

Set the triangle to the hour or minute position when you wish to complete the

activity, and check the watch periodically for progress towards that goal.

In the illustration shown on the previous page on the right you can stop when

the minute hand reaches the 20 minutes past the hour position.

TACHYMETER RING

The tachymeter feature can be used to measure speed in miles per hour (MPH),

nautical miles per hour (knots) or kilometers per hour (KPH) using the sweep

second hand and the scale on the wall above the watch face. You need to

know the actual distance you are covering in miles or km.

Start the chronograph with the second hand at zero (the twelve o’clock

position). Within the ﬁrst minute, the second hand will point to the rate for a one-

mile (or one kilometer) course: if it takes 45 seconds, the hand will point to 80 at

that position – 80 MPH or 80 KPH.

If within the ﬁrst minute, a distance greater than one mile or kilometer is

covered, multiply the tachymeter number by the distance to get the actual rate:

if you went 1.2 miles in 45 seconds, multiply the 80 by 1.2 – 96 MPH.

COMPASS RING

If your watch is equipped with a movable ring around the dial marked at the

letters “N”, “E”, “W”, “S” (for the four compass directions) or compass degrees,

you can use this feature to ﬁnd an approximate compass directional reading.

1. Lay the watch on a ﬂat surface, or hold it so that the face is parallel to the

ground.

2. Locate the sun and point the hour hand at the sun.

3. In the A.M., rotate the ring until the “S” (south) marker is halfway between

the hour hand and 12:00 (after the hour hand or within the shortest distance

between the hour hand and 12:00).

4. In the P.M., rotate the ring until “S” is before the hour hand and halfway

between the hour hand and 12:00.

12 1

HOW TO ADJUST BRACELET

(Variations of the following bracelet sections apply to all watch models).

SLIDING CLASP BRACELET

1 Open locking plate.

2. Move clasp to desired bracelet length.

3. Exert pressure while holding locking plate and slide clasp back and forth until

it engages in grooves on underside of bracelet.

4. Press locking plate down until it snaps closed. Clasp can be damaged if

excessive force is used.

FOLDOVER CLASP BRACELET

1. Find spring bar that connects bracelet to clasp.

2. Using a pointed tool, push in spring bar and gently twist bracelet to

disengage.

3. Determine wrist size, then insert spring bar in correct bottom hole.

4. Push down on spring bar, align with top hole and release to lock in place.

Fig. 2Fig. 1 Fig. 3

BRACELET LINK REMOVAL

REMOVING LINKS:

1. Place bracelet upright and insert pointed tool in opening of link.

2. Push pin forcefully in direction of arrow until link is detached (pins are

designed to be dicult to remove).

3. Repeat until desired number of links are removed.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Timex W223 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Timex W223

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info