Handleiding Thomson ROC8507 (pagina 9 van 48) (Nederlands, Duits, Engels, Frans, Italiaans, Spaans)

607824

Verklein

Vergroot

Pagina terug

1/48

Pagina verder

Notes on learning: Do not try to perform learning

directly under fluorescent lights or in weak lighting

conditions since this could cause interference with the IR

transmissions. Place the remote control at least 1 metre

[3 feet] from any light source • Avoid copying the volume

and mute keys on your original remote control, unless

you are sure that they activate the same target device;

for example, certain original DVD remote controls may

also include a TV volume/mute key: they may have two

different types of codes • Avoid learning VCR keys on your

original remote control unless you are sure that they

activate the same target device; for example, certain

original TV remote controls may also include a VCR key:

they may have two different types of codes • Copying

a key may take up to 3 seconds. Do not release the key

being copied unless the “Success” or “Key Learn Error”

screens are displayed.

If copying the  rst or second keys for a certain mode

constantly cause errors, use the following procedure:

i. E nd the learning session by pressing the EXIT key.

ii. C lear the commands learned for this mode.

iii. V erify that the IR LED’s are properly aligned between the

two remote controls.

iv. A just the gap between the two remote controls so as to

reduce or increase the distance (from 15 mm to 50 mm

[1/2 to 2»]).

v. T ry learning the original remote control again for this

mode.

If the problem continues for the same key, verify that the key

on the original remote control was properly learned; does

it send the signals? Does it activate the target device? Try

copying this key using a di erent mode. If the learning is

correct, the type of code may be di erent from the others

and cannot be copied in the same mode.

Macro commands

This function permits storing sequences of commands

using the MACRO key. You can program and store up

to 3 sequences of successive keystrokes for several

keys of your choice. By pressing the respective Macro

digital key, this sequence of successive keystrokes

(IR commands) is sent. Any sequence of successive

keystrokes performed frequently may be reduced to

only two commands (MACRO key plus one of the 1, 2 or

3 keys). For example, by pressing MACRO and then only

one key, you can turn on your TV set, display your favorite

channel, turn on your VCR and start a recording, etc.

You can store a sequence of 10 commands for each 1, 2

or 3 key.

How to set up a macro

Tip: Set up your macro on a sheet of paper by

writing down the series of 10 keystrokes (maximum)

that it is composed of. As an example, if you want to

turn on your TV set to Channel 3 and then turn on a

satellite receiver to Channel 5, you should write down:

MACRO, 1 (for storage for this key), TV (Ђ), 3, SAT (Ђ),

5, MACRO.

1. U sing the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate up to MACRO SETUP (press

OK) then MACRO KEY SET (press OK) then SELECT A

MACRO KEY.

2. P ress once on the 1, 2 or 3 key to which you wish to

assign the macro.

T he indication SELECT MACRO X MODE? appears.

4. P ress once on the desired mode key (TV, DVD,

VCR, etc.) to select the device that will receive the

command SELECT MACRO X KEY? is displayed.

Note: The  rst key in the Macro sequence must always be

a mode key.

5. P ress each of the keys in order that make up the

macro.

6. S tore the macro by pressing the MACRO key once.

7. T he display brie y indicates PLEASE WAIT before

leaving this mode.

Note: the Macro is automatically stored the 10th time the

key is pressed.

8. T he display brie y indicates SUCCESS before leaving

this mode.

How to clear a macro

1. U sing the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate up to MACRO SETUP (press OK)

then MACRO KEY CLEAR (press OK) then SELECT A

MACRO KEY.

2. P ress once on key 1, 2 or 3 of the macro to be cleared

to display CONFIRM OK TO CLEAR

3. P ress OK once.

4. T he display brie y indicates SUCCESS before leaving

this mode.

How to use a macro

In normal operation, to activate the Macro, press and

release the MACRO key, then (within 20 seconds) press

and release key 1, 2 or 3 to display MACRO X while the

Macro sequence is being run and remote control returns

to normal function. While the Macro is being executed,

the remote control must be pointed at the devices to be

controlled.

Note: if there is no Macro stored for the number key selected,

“Macro X Void“ is displayed.

Notes on macros: The time elapsed between each automatic

command during the execution of a macro is 1/2 second.

For certain commands, you may have to add pauses in a

macro sequence (for example, to allow the TV set to warm

up). These pauses may be adjusted by using the PAUSE key,

followed by a number of seconds from 1 to 9. The  rst key

stored in a Macro sequence must be a Mode key (TV, VCR,

etc.). The SETUP, HOME CINEMA and MACRO keys may

not be included in a Macro. Press SETUP in order to exit

Macro Setup.

Home Cinema Function

The Home Cinema function uses up to 5 devices with

one mode key: the HOME CINEMA key. The 5 devices

correspond to the  ve mode keys (TV, DVD, AMP...) that

will be associated with prede ned keys. The keys are:

a. The 2 program keys PROG + / -.

b. T he 3 volume VOL + / - keys and the mute ( ) key.

c. T he 6 run keys Play, Pause, Stop, Fast Forward, Fast

Rewind and Record 7,4,8,=,<,;.

d. D irectional keys: up, down, right and left 5,6,4,3

and the MENU, EXIT, OK keys.

e. F or the remaining keys: "base" mode HOME CINEMA

(any one of the other modes).

Example: In Home Cinema mode, you can set up the

PROG+/ keys to control the satellite receiver, the VOL +/

and ( ) keys to control the ampli er, the Run keys (PLAY,

PAUSE, etc.) to control the DVD player, the MENU, EXIT, etc.

keys to control the DVD player, and the other keys to control

the TV set.

How to program the Home Cinema function

1. U sing the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate to HOME CINEMA SETUP (press

OK) then HOME CINEMA SET (press OK) then PROG/

CHAN KEY GROUP MODE?.

2. C hoose a mode key (TV, DVD, VCR, etc.) for the PROG

+ / - keys.

> VOLUME & MUTE KEYS MODE? appears.

3. C hoose a mode key (TV, SAT, AMP, AUDIO, etc.) for

the VOL + / - keys.

>RUN KEYS MODE? appears.

4. C hoose a mode key (TV, DVD, VCR, etc.) for the

7,4,8,=,<,;run keys.

>xxx MENU, OK, EXIT MODE? appears

5. C hoose a mode key (TV, DVD, VCR, etc.) for the

navigation keys MENU, EXIT, OK.

> ALL OTHER KEYS MODE? appears.

6. C hoose a mode key (TV, DVD, VCR, etc.) for the other

remote control keys to be used for Home Cinema

mode.

The display brie y indicates PLEASE WAIT then

SUCCESS before returning to CODE SETUP.

How to delete the Home Cinema function

1. U sing the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate to HOME CINEMA SETUP (press

OK) then HOME CINEMA RESET.

2. Press OK once to display CONFIRM OK TO RESET.

3. Press OK once.

Thomson ROC8507 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info