Handleiding Thomson ROC4411 (pagina 8 van 74) (Alle talen)

699749

Verklein

Vergroot

Pagina terug

1/74

Pagina verder

Replacing the batteries

Replacing the batteries in the remote control

and in the base

Remote Control:

Use 2 AAA 1.5Volt batteries

1. Open the cover on the back of the remote control by

pushing down on the tab and lifting the cover off.

2. Check the +/– polarity on the batteries and inside

the compartment.

3. Insert the batteries.

4. Press the battery cover back into place.

When exchanging the batteries, it may be necessary to

reprogram the unit. Hence it is advisable to record the

codes needed for your devices.

Other functions

Placing all devices on standby

Press the G key twice in less than one second, keeping

it held down the second time. All the devices go on

standby one after the other (the devices which were

already on Standby may turn on).

Adjustment of ALL volume controls under a

specic mode

In its delivered state, the ROC4411 is programmed

such that all modes will use their own Volume and

Mute functions if present.

You can allocate the volume control to one of the

modes of the remote control on condition that the

volume control exists on the corresponding device

(e.g. control of TV sound in TV mode, DVD mode,

Mode, etc.).

1. Hold the SETUP key down until the indicator lamp

blinks and then remains lit.

2. Release the SETUP key

3. Press the H key until the indicator lamp blinks

once.

4. Press once on the mode key (TV, DVD, …)

corresponding to the device whose volume will

always be controlled by the VOL and H keys.

5. Press the H key once. The indicator lamp goes off.

6. All other mode will now punch-through to your

chosen mode for Volume and Mute control.

Adjustment of the volume controls for EACH

mode.

You can decide that the volume control is functional

for each mode selected on condition that the volume

control exists on the corresponding device (e.g. control

of the television set sound in TV mode, the control of

the sound of the SAT receiver in SAT/STB mode, …).

1. Hold the SETUP key down until the indicator lamp

blinks and then remains lit.

2. Release the SETUP key

3. Press the H key until the indicator lamp blinks

once.

4. Press once on the mode key (TV, DVD, …)

corresponding to the device whose volume will

always be controlled by the VOL and H keys.

5. Press the VOL- key once.

6. Press the H key once. The indicator lamp goes

off.

7. The chosen mode key will now use its own Volume

and Mute functions

Restoring the universal Volume/Mute

functions

If you have changed the universal volume and mute

functions, as described in the previous two sections,

you can reset the functions back to the factory settings:

1. Hold the SETUP key down until the indicator lamp

blinks and then remains lit.

2. Release the SETUP key

3. Press the H key until the indicator lamp blinks

once.

4. Press and release the H key. The indicator lamp

will go off completely. The volume and mute

functions are now restored to their factory defaults.

Programming a sequence

of commands (Macro)

The MACRO key in coordination with one of the keys

1, 2, or 3, allows the programming and memorisation

of up to 3 command sequences (the automatic and

successive pressing of several keys of your choice). Thus

any sequence of key commands can be reduced to

merely 2 commands (MACRO key + key 1, 2, or 3).

For example after programming, by pressing MACRO

then key 1 you could turn on your television set, turn on

your satellite or cable receiver, zap to a preferred

channel, turn on your video cassette recorder and start

a recording session (providing a cassette was

previously loaded). You can memorise a sequence of

10 commands with each key 1, 2, or 3.

Note

during the programming of a macro, the time

between each step is limited to a few seconds. This

leaves little time for reading the instructions and then

carrying them out. If the mode indicator light blinks

and then goes out, it is because this time limit has

been exceeded, you must start again from step 1.

o record a MACRO:

1. Press and hold down the SETUP key until a (TV,

DVD, …) mode key blinks and remains lit (after 2

or 3 seconds).

2. Release the SETUP key.

3. Press the MACRO key once. The mode key blinks.

4. Press once the 1, 2 or 3 key which you are going

to use to memorise the sequence.

5. Press once on the (TV, DVD, …) mode key of the

first device you wish to control (the first key must

always be a mode key.)

6. Successively press the keys corresponding to the

commands you wish to send to the device(s) (9 keys

maximum, including other mode keys). The mode

key blinks when each key is pressed.

7. Memorise your key sequences by pressing the

MACRO key once. The mode key is no longer lit

and your Macro is complete.

Note

a sequence will be automatically memorised

after the tenth key press (counted from the mode key)

and the mode key light will go out.

o use a MACRO:

Press the MACRO key once and, within 20 seconds,

press the 1, 2 or 3 key you used to memorise the

sequence.

Note

when running a Macro (which takes a few

seconds), ensure that the remote control is aimed at

the device being controlled.

Remarks

• The default time between sending 2 commands when

using a macro is half a second.. However, it is

possible that you will need to add longer periods in

your sequence in order to allow enough time for

certain devices to turn themselves on. To lengthen the

time period between 2 commands, press once on the

key and then press one of the keys from

order to insert a pause from 1 to 9 seconds.

• The first key in a sequence must always be a mode

key (

DVD

, …).

Note

the indications

DVD

STB

(below keys

) are only an aid to memory. You may decide, for

example, to memorise a MACRO for the television

set using key

, etc.

Deleting a MACRO

1. Press and hold down the SETUP key until the (TV,

DVD…) mode key blinks and then remains lit (after

2 or 3 seconds).

2. Release the SETUP key.

3. Press once on the MACRO key. The mode key

begins to blink.

4. Press once the 1, 2 or 3 key that represents the

sequence to delete.

5. Press and hold down the SETUP key. The mode key

light goes out and the sequence is now deleted.

M1, M2 or M3

Thomson ROC4411 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info