- EN 10 -
90 and 120 minutes. Press the STOP/SELECT button to select. The source for the alarm will now ash.
9. Use the NEXT/PREV button to scroll to the sound source for the alarm. You can choose from
Buzzer, DAB, FM, CD or USB. Press the STOP/SELECT button to select.
Note: If you select DAB or FM radio for the alarm source, ‘Last listened’ will ash in the display. Press
the STOP/SELECT button to select the last radio station tuned in DAB or FM (as applicable) will be
used for your alarm.
10. Use the NEXT/PREV button to scroll to the alarm frequency. You can choose from Daily, Once,
Weekends or Weekdays. Press the STOP/SELECT button to select.
Note: If you select ‘Once’, you will then be prompted to set the date for your alarm.
11. Use the NEXT/PREV button to set the volume for your alarm. Press STOP/SELECT button to select.
Note: Remember to set the alarm radio volume to one that will wake you. The alarm volume will
increase progressively until it reaches the alarm volume you have set.
12. ‘Alarm 1 Wizard’ is displayed again, together with ‘Alarm Off (or On)’. Use the NEXT/PREV button
to choose ‘Alarm On’ or ‘Off and press STOP/SELECT button to select. ‘Alarm Saved’ is displayed.
13. A bell symbol in the top right of the display, together with the digit ‘1’ or ‘2’ as appropriate, will
conrm when an alarm has been set.
Note: If the time is not set or has failed to update from the radio signal, ‘Time is not set’ will be displayed
when you try to set the alarm. The radio will then prompt you to set the time. An alarm can only be set
after the time has been set.
Stop the Alarm
When the alarm sounds, press and release the POWER/MODE BUTTON. ‘Alarm off’ is displayed.
Alternatively, you can press and release the ‘SLEEP/SNOOZE’ button on the remote control (see
Snooze function below).
Note: If you press the POWER/MODE BUTTON to stop the alarm, the alarm symbol will remain in the
display and the alarm will sound again at the same time the next day, unless it was set for ‘Once’ only.
Snooze
When the alarm sounds, you may press and release the ‘SLEEP/SNOOZE’ button on the remote control.
‘Snooze 9 minutes’ will be displayed, followed by the snooze time countdown, until the alarm sounds again.
Turn Off the Alarm
Follow the steps for ‘Setting an Alarm’ and select ‘Off’ at step 12.
Sleep Timer
You can set your radio to turn off automatically using the sleep timer. You can choose from Sleep off,
15, 30, 45, 60, and 90 minutes.
With your unit switched on (not in Standby mode):
1. Press and hold the Menu/Info button to enter the menu options.
2. Use the NEXT/PREV button to scroll to <System > then press the STOP/SELECT button.
3. In System menu, use the NEXT/PREV button to scroll to <Sleep> then press STOP/SELECT button.
4. Use the NEXT/PREV button to cycle through the different sleep time options such as Sleep off, 15,
30, 45, 60 and 90 minutes. Press the STOP/SELECT button to conrm.
Note: To cancel the sleep timer, follow the steps to set the sleep time but stop when ‘Sleep off’ is displayed.
Display Backlight Timeout
You can adjust the display backlight timeout. Options of permanently On, 10, 20, 30, 45, 60, 90, 120,
and 180 seconds are available. An ‘*’ will be displayed next to the current setting.
With your unit switched on (not in Standby mode):
1. Press and hold the Menu/Info button to enter the menu options.
2. Use the NEXT/PREV button to scroll to <System>. Press and release the STOP/SELECT button.
3. Use the NEXT/PREV button to scroll to <Backlight>. Press and release the STOP/SELECT button.
4. <Timeout> is displayed. Press and release the STOP/SELECT button. Use the NEXT/PREV button to
scroll through the available backlight timeout options of On, 10, 20, 30, 45, 60, 90, 120 or 180 seconds.
Stop when the backlight timeout you would like is displayed and press and release the STOP/SELECT
button. <Timeout> will be displayed. You may now use the NEXT/PREV to scroll and the STOP/SELECT
BUTTON to select, as you did to set the Backlight timeout, to change the settings for the backlight
