607258
6
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
Page 6
3.7 Changing the signal code
It is possible that there are multiple units within the reach of one transmitter; the
transmitter can be customised for each unit if required. This can be performed by
changing the signal code in the transmitter.
There are 15 other codes that can be set by adjusting the position of one or more
“DIP switches” in the transmitter.
The “DIP switches” are accessible after opening the battery holder of the
transmitter.
Simultaneously press the reset key on the receiver and the key on the
transmitter (approximately 20 seconds).
When the receiver has read the new code, the gas block responds and is ready for use.
3.8 Controls (Remote Control)
Igniting the fire
Open the gas shut-off cock that has been installed in the gas pipe to the unit.
Press the "O I” switch on the gas control block, into the “I” position.
Turn the operating button on the gas control block, into the ON position.
Simultaneously push the keys
OFF and
on the manual transmitter. A short sound signal will confirm
commencement. Short sound signals will then follow until the pilot flame and main burner are ignited.
After the main burner is ignited, the flame size will automatically move into the maximum setting.
3.9 Possible error messages
Long sound signals during the ignition: Receiver batteries are almost empty. (After this signal occurs, the
unit can be switched on approximately another 10x).
5 seconds of continuous sound signal: Error message. For example: one of the cables is not connected, the
O I” switch is not in the “I” position.
5x short sound signal: Ignition of the pilot flame and main burner is unsuccessful.
Possible cause: air in the pilot pipes.
Important:
If the pilot light extinguishes, one should wait at least 5 minutes before repeating the aforementioned
steps.
“DIP switches” in the
transmitter battery holder
Piezo connector
(With manual
operation)
Control button
Motor button (in the
maximum setting)
Microswitch
O I” switch
8-Pole cable receiver
connection
Gas control block (Operating button in ON-position
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thermocet Estilo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thermocet Estilo in de taal/talen: Engels als bijlage per email.

De handleiding is 3,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info