606550
58
Verklein
Vergroot
Pagina terug
1/71
Pagina verder
Continuous valve actuator CHEOPS control
theben
As of: Jul-11 (Subject to change without notice) Page 58 of 71
5.7 Determine the maximum actuating value
5.7.1 Application
If within a system all valve actuators are only slightly open, e.g. one at 5%, one at 12%,
another at 7% etc., the heating boiler can reduce its output because only a small amount of
heating energy is required.
In order to guarantee this, the heating boiler requires the following information:
How high is the actuating value in the room, which currently exhibits the greatest heat
requirement?
With Cheops valve actuators, this task is handled by the "Maximum position" function.
5.7.2 Principle
The actuating values are constantly compared between all participants (Cheops valve
actuators). Those participant with a higher actuating value than the one received may send it,
those with a smaller one may not.
In order to accelerate the process, the greater the difference between its own and the received
actuating value, the greater the speed at which the valve actuator sends.
Thus, the valve actuator with the highest actuating value sends first and beats the remainders.
5.7.3 Practice
The actuating value comparison takes place via Object 3 ("Maximum position") where
for each valve actuator, a common group address for the maximum position is placed on
Object 3.
In order to start the actuating value comparison between the participants, one (and only one)
participant must send a value to this group address cyclically.
This task can be handled by either boiler or valve actuator.
If it is the boiler, it must send the smallest possible value, i.e. 0%.
If it is a Cheops valve actuator, the parameter " Transmission of object
"Max. actuating value"(for boiler control)" on parameter page " Security and forced mode”
must be set to any cycle time.
This valve actuator then regularly sends its own actuating value and the others can respond
accordingly.
Irrespective of which participants act as initiator, the "Transm. of object “max. actuating
value” (for heating system)" must be set to the default value for all other valve actuators, see
Figure:
58

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Theben CHEOPS control KNX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Theben CHEOPS control KNX in de taal/talen: Engels als bijlage per email.

De handleiding is 0,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Theben CHEOPS control KNX

Theben CHEOPS control KNX Gebruiksaanwijzing - Nederlands - 76 pagina's

Theben CHEOPS control KNX Gebruiksaanwijzing - Deutsch - 72 pagina's

Theben CHEOPS control KNX Gebruiksaanwijzing - Deutsch - 1 pagina's

Theben CHEOPS control KNX Gebruiksaanwijzing - English - 1 pagina's

Theben CHEOPS control KNX Gebruiksaanwijzing - Français - 74 pagina's

Theben CHEOPS control KNX Gebruiksaanwijzing - Français - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info