742908
134
Verklein
Vergroot
Pagina terug
1/139
Pagina verder
Copyright
Statement
i
Copyright Statement
is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the
products and product names mentioned herein are the trademarks or registered
trademarks of their respective holders. Copyright of the whole product as integration,
including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd.
No part of this publication can be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language in any form or by any means without the
prior written permission of Shenzhen Tenda Technology Co., Ltd. If you would like to know
more about our product information, please visit our website at http://www.tendacn.com.
Disclaimer
Pictures, images and product specifications herein are for references only. To improve
internal design, operational function, and/or reliability, Tenda reserves the right to make
changes to the products without obligation to notify any person or organization of such
revisions or changes. Tenda does not assume any liability that may occur due to the use
or application of the product described herein. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements,
information and recommendations in this document do not constitute the warranty of any
kind, express or implied.
Preface
ii
Preface
Thank you for choosing Tenda! Reading this manual will be helpful for you to configure
this device.
Convention
If not specifically indicated, the switch, this product or this device mentioned in this Install
Guide stands for Tenda 8GE+2SFP Managed PoE Switch TEG3210P.
Symbols in this Install Guide:
Symbol
Meaning
Note
Ignoring this type of note may result in a malfunction or
damage to this device.
Tip
This format is used to highlight a procedure that will save
time or resources.
Overview of this Install Guide
Chapter
Description
Chapter I Product
Overview
Introduction to this switch’s package contents, physical
appearance and features
Chapter II Installation
Introduction to this switch’s installation considerations and
installation procedures
Chapter III Device
Management
Introduction
Introduction to how to manage the switch via Web manager
and fundamental operations about Web manager
Chapter IV Advanced
Settings
Introduction to how to configure functions of the switch
Chapter V Appendix
Introduction to technical specifications, default settings and
safety statement of the switch
Technical Support
Website: http://www.tendacn.com
Telephone: (86 755) 2765 7180
Email: support@tenda.com.cn
iii
Contents
Product Overview .......................................................................................................................... 1
Package Contents ............................................................................................................................. 2
Physical Appearance ......................................................................................................................... 2
Installation....................................................................................................................................... 6
1 Installation Considerations ............................................................................................................ 7
2 Tools ................................................................................................................................................. 8
3 Installation ....................................................................................................................................... 8
4 Connect to Protective Grounding Cable ................................................................................... 10
5 Connect to Power Supply............................................................................................................ 11
6 Cable Connection ......................................................................................................................... 11
7 Power up the Device .................................................................................................................... 14
Device Management Introduction .......................................................................................... 15
1 Web Administration ...................................................................................................................... 16
2 Web Login ..................................................................................................................................... 16
3 Web Logout ................................................................................................................................... 18
4 Layout of Web Browser-Accessible Administrator Page ........................................................ 18
5 Commonly Used Elements on Web Browser-Accessible Administrator Page .................... 19
Advanced Settings ...................................................................................................................... 21
Administration .................................................................................................................................. 22
Port Management ............................................................................................................................ 32
VLAN Management ......................................................................................................................... 44
PoE Management ............................................................................................................................ 62
Time Range Management .............................................................................................................. 64
Device Management ....................................................................................................................... 66
QoS .................................................................................................................................................... 99
Security ........................................................................................................................................... 110
Maintenance ................................................................................................................................... 116
Logout ............................................................................................................................................. 122
Save Configurations ...................................................................................................................... 123
Appendix ..................................................................................................................................... 126
Technical Specifications ................................................................................................................ 127
iv
Default Settings .............................................................................................................................. 130
Safety and Emission Statement................................................................................................... 134
Product Overview
Package Contents
Physical Appearance
Product
Overview
2
Package Contents
Open the package and verify the following items:
Switch *1
Power Cord *1
L-shaped Bracket *2
Screw *6
Footpad *4
Install Guide *1
If any item is missing or damaged, contact the place of purchase immediately.
Physical Appearance
1 Front Panel
The following parts are located on the front panel shown as below.
Reset Button
With the switch powered on, pressing the Reset button for at least 5 seconds and then
releasing it restore the switch to factory default settings. The switch will reboot
automatically after reset and this process takes about 45 seconds.
While rebooting, following phenomena will occur: All LEDs light upSYS LED is offAll
LEDs are off except the Power LEDSYS is on and blinking.
LEDs
The following table describes the LED designations
LED
Status
Description
Power
Solid
Proper connection to power supply
Off
Improper connection to power supply or malfunction
occurs.
SYS
Blinking
The system is functioning properly.
Solid
The system is functioning improperly.
Product
Overview
3
Off
The system is still rebooting.
Link/Act
Solid
A valid link is established on the corresponding RJ45 port.
Blinking
Data transmission is occurring on the corresponding RJ45
port.
Off
No link is established on the corresponding RJ45 port.
PoE/Status
Solid
The PoE powered device (PD) is connected on the
corresponding RJ45 port and the port is supplying power
successfully.
Off
No PoE powered device (PD) connected.
SFP1&SFP2
Solid
A valid link is established or data transmission on the
corresponding SFP port.
Off
No link is established on the corresponding SFP port.
RJ45 Ports
This switch comes with 8 10/100/1000Mbps auto-negotiation RJ45 ports. Each port has a
corresponding Link/Act LED. Speeds and corresponding working modes of all RJ45 ports
are described in the following table.
Speed
Working Mode
10Mbps (auto-negotiation)
Half/Full duplex auto-negotiation
100Mbps (auto-negotiation)
Half/Full duplex auto-negotiation
1000Mbps (auto-negotiation)
Full duplex auto-negotiation
All RJ45 ports are PoE-capable, and can connect up to 8 IEEE 802.3af-compliant PDs
(15.4W for each) or 4 IEEE 802.3at-compliant PDs (30W for each).
Tip:
As pair 1, 2 and pair 3, 6 are applying PoE power supply, it is advisable to use cat 5 or
higher UTP/STP cables. Note that Ethernet specifications limit the cable length between
the switch and the attached device to 100 m (328 ft).
Product
Overview
4
SFP Ports
This switch comes with 2 1000Mbps SFP fiber ports, accommodating a standard SFP
fiber module.
SFP (Small Form-factor Pluggableis a compact, hot-pluggable transceiver mainly used
for implementing the switchover between fiber and electricity signals, including fiber rate
control, modulation sending, signal detection, IV transformation and amplifier limiting
judgment regeneration.
An optical fiber connector terminates the end of an optical fiber. The optical fiber
connector (known as union), an indispensable passive device in optical fiber
communication, is mainly used for detachable optical fiber connection, which is not only
convenient for commissioning test and maintenance of the optical fiber system, but makes
this system’s switch-over and scheduling more flexible.
TEG3210P only supports LC optical fiber connector as shown below:
Tip:
The optical fiber module or photoelectric converter is not included in the package and you
need to prepare it by yourself.
2 Back Panel
The following parts are located o[n the back panel as shown below:
Product
Overview
5
Power ON/OFF
Used for controlling power supply of this device.
Grounding Terminal
Used for connecting the protective grounding cable for inductive lightning protection. As
for the method of connecting protective grounding cable, please refer to Connect to
Protective Grounding Cable.
Power Socket
Used for connecting the included power cord for power supply.
6
Installation
Installation Considerations
Tools
Installation
Connect to Protective Grounding Cable
Connect to Power Supply
Cable Connection
Power Up the Device
7
Installation
1 Installation Considerations
To avoid any equipment damage or bodily injury caused by improper use, read the
following safety recommendations before installing the switch. Note that the
recommendations do not cover every possible hazardous condition.
Safety Caution
Do wear anti-static wrist straps and disable the power supply of this device while
installing this device;
Use the included power cord for power supply;
Ensure operating power supply accords with rated input standard;
Ensure ventilation holes of the switch are in good condition;
Do not open or remove the housing of the switch;
Do disconnect power supply while cleaning the switch and do not use any liquid to
clean the switch;
It's suggested to ground the switch to avoid strong inductive lightning. Keep the
switch away from power lines, electric lights or strong power grid or anywhere the
power grid with strong current is reachable, all for better performance.
Note:
There is a Tenda seal on one of the screws. You should keep the seal unbroken before the
technical staff maintains your switch. You cannot open the housing of the device unless
you get the local reseller’s permission, or you have to be responsible for the result that the
device cannot be maintained because of unpermitted operation.
Site Requirements
1. Temperature & Humidity
Environment
Temperature
Humidity
Operating
-10ºC ~ 45ºC
10% ~ 90%RH (non-condensing)
Storage
-40 ~ 70
5%~90% RH (non-condensing)
2. Cleanliness Requirements
In case that static electricity affects this devices normal operation, please observe
following guidelines:
Keep indoor environment clean and dust the switch regularly;
Keep the switch well-grounded for electrostatic transferring.
8
Installation
3Inductive Lightning Protection
In case that strong current does damage to the switch due to inductive lightning, verify
that:
Power socket, rack, work bench and the grounding terminal of the switch are
well-grounded;
The switch is cabled properly. When the switch is cabled outdoors, it is advisable to
use it together with the signal lightning arrester.
4. Installation Site Requirements
Whether install the switch in a rack or on a flat work bench, please verify:
The rack or work bench is stable and sturdy enough;
The switch should be clean and well ventilated. There is at least 10 centimeters free
on all sides for cooling;
No articles, especially heavy articles, are placed on the switch;
There is more than 1.5 centimeters vertical distance free between devices that stack
up.
2 Tools
Before installing the switch, prepare the following tools:
Antistatic Gloves Phillips Screwdriver Ethernet Cable
3 Installation
The switch can be installed either in a rack or on a desktop. You can choose the more
suitable one as you need.
A. Mount the switch in a rack
With the included L-shaped brackets and screws, you can install it in a 19-inch standard
rack.
Step 1: Make sure the rack is well-earthed and stable;
Step 2: Attach the included mounting brackets to the two sides of the switch with the
included screws;
9
Installation
Step 3: Insert screws (prepared by yourself) through each bracket and into the rack to
securely fix the switch onto the rack.
B. Mount the switch on a desktop
Without a 19-inch standard rack, you can install the switch on a desktop.
Step 1: Place the switch bottom up on a flat desktop;
Step 2: Attach four footpads to the corresponding circular grooves on the bottom of the
switch;
10
Installation
Step 3: Place the switch face up on the desktop.
4 Connect to Protective Grounding
Cable
Proper connection of protective grounding cable is not only important for inductive
lightning protection and anti-interference, but for your own personal safety. Please select
the most suitable method to connect protective grounding cable according to your
installation environment.
A. With grounding bar
Step 1: Connect one end of the protective grounding cable to the binding post on the
grounding bar.
Step 2: Connect the other end of the protective grounding cable to the grounding terminal
and fix the screws.
B. Without grounding bar
With mud land nearby and allowed to bury grounding bar, follow below steps:
Step 1: Bury an angle iron or steel pipe (≥0.5m) into the mud land;
Step 2: Weld one end of the protective grounding cable to the angle iron or steel pipe and
embalm the welding point;
11
Installation
Step 3: Connect the other end of the protective grounding cable to the grounding terminal.
If not allowed to bury the grounding bar, you can connect it to ground through the
three-core PE cable of the AC power socket on the precondition that the PE cable in the
switchgear room or beside the AC power supply transformer is well-grounded.
5 Connect to Power Supply
Please use the included power cord for power supply.
6 Cable Connection
Connect to RJ45 Ports
Connect the switch to remote Ethernet devices with Ethernet cables.
12
Installation
Tip:
All RJ45 ports of the switch are Auto MDI/MDIX-capable, which allows you to attach
devices using twisted pair category 5 or higher, either straight-through or crossover
cables.
Connect to SFP Fiber Ports
Step 1: Insert the SFP module into the SFP module bay.
Step 2: Insert the LC optical fiber connector of the fiber into the SFP module.
13
Installation
Connect to PDs
The PoE power supply feature on all RJ45 ports is enabled by default. You can connect
IEEE 802.3at-/802.3af-compliant APs, IP telephones, IP cameras or other powered
devices to the switch.
14
Installation
Tip:
The PoE power supply mode is dynamic, i.e. the switch accommodates power supply for
powered devices automatically.
7 Power up the Device
Check the device thoroughly before powering up the device.
7.1 Check the Device
Before applying power supply, perform the following:
The operating power supply should accord with rated input standard;
The power cord and grounding cable is correctly connected;
All cable connections (RJ45 ports, SFP ports) are correct.
If cabling outside, ensure the Ethernet port lightning arrester and AC power source
lightning arrester are connected.
7.2 Power up the Device
Step 1: Turn on the power switch (Power ON/OFF) on the back panel to power up the
switch.
Step 2: After being powered on, the switch will be initialized automatically. Please ensure
that following phenomena will occur to LEDs one by one:
All LEDs (Power, SYS, PoE/Status, Link/Act, SFP1, SFP2) will light up for
self-checking.
SYS LED is off.
All LEDs are off except the Power LED.
After restart, the Power LED lights up, SYS LED is blinking, corresponding Link/Act
LED or SFP1/SFP2 LED is on or blinking and corresponding PoE/Status LED lights
up.
Device Management
Introduction
Web Administration
Web Login
Web Logout
Layout of Web Browser-Accessible Administrator Page
Commonly Used Elements on Web Browser-Accessible
Administrator Page
16
Device
Management
Introduction
1 Web Administration
This switch comes with the web administration feature, which helps you manage and
maintain this switch intuitively via its web browser-accessible administrator page. The
network topology of application scenario is shown below:
2 Web Login
The first time you use this device, you can log in to its web browser-accessible
administrator page with following default login info.
Login Info
Default Settings
User Name
admin
Password
admin
IP Address
192.168.0.1
Web Login:
1 Connect the PC to an RJ45 port of the switch using an Ethernet cable.
2 Configure your PC’s IP, which should be in the same network segment but be
different from the switch’s management IP. The default management IP of the
switch is 192.168.0.1, so you can set your PC’s IP to Use the following IP
address: IP address: 192.168.0.X (where X can be any number between 2 and
254); subnet mask: 255.255.255.0.
Appendix
129
Support bandwidth control
Up to 4-queue QoS mapping can be configured.
Certification
Support port based IEEE 802.1X certification
Loading and
Upgrading
HTTP
Management
Support SNMP (Simple Network Management
Protocol)
Support Web management
Support Telnet management
Port Management
Port Setup: port speed rate setup and display, flow control
setup, isolation setup, Jumbo frame setup (1518-9216)
Port Mirroring: implement port ingress mirror image, egress
mirror image and ingress & egress mirror image
Port Statistics: display packets the port has received and
sent
Port Trunk: implement static trunk and LACP and up to 2
trunk groups can be configured with 2~8 ports in each
group.
PoE
Support IEEE 802.3at standard
Support IEEE 802.3af standard
Maximum power consumption: 115W
Time Range
Management
Support absolute time, periodic time and superposition of
time slices and applicable for PoE. Up to 16 time ranges
can be configured and as for each time range, at most 4
time slices can be allowed.
Maintenance
Support Ping\Tracert\Cable test
134

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Tenda TEG3210P bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Tenda TEG3210P in de taal/talen: Engels als bijlage per email.

De handleiding is 8,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info