627190
7
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
- 7 -
2- Selector for adjusting the 3 welding ranges and for adjusting the
output voltage of the auxiliary sockets.
3- Negative quick connector (-) for welding cable connection.
4- Positive quick connector (+) for welding cable connection.
5- Auxiliary socket voltmeter.
6- Circuit-breaker.
7- Single-phase socket.
8- Three-phase socket.
9- Hole for earth connection.
5.INSTALLATION
WARNING! CARRY OUT ALL INSTALLATION AND
ELECTRIC CONNECTION OPERATIONS WITH THE ENGINE-
DRIVEN WELDING MACHINE RIGOROUSLY SWITCHED OFF.
THEELECTRICCONNECTIONSMUSTONLYBECARRIEDOUT
BYEXPERTORQUALIFIEDTECHNICIANS.
PREPARATION
Unpack the engine-driven welding machine and assemble the
separate parts included in the package.
Returncable-clampassembly
Fig.D
Electrode-holderclamp-weldingcableassembly
Fig.E
HOWTOLIFTTHEENGINE-DRIVENWELDINGMACHINE
The engine-driven welding machine MUST be lifted as shown in Fig.
F.
This is valid for both initial installation and for the entire life of the
engine-driven welding machine.
Note: The wire feeder, gas bottle, cables and interconnecting and
supply cables must be removed before lifting the engine-driven
welding machine. Make sure the lifting cables, belts or chains do not
damage the engine-driven welding machine accessory parts.
POSITIONINGTHEENGINE-DRIVENWELDINGMACHINE
Make sure the engine-driven welding machine is positioned in a
place where the cooling air inlets and outlets cannot be obstructed;
at the same time make sure that conductive dust, corrosive vapours,
humidity etc. cannot be drawn into the machine.
Leave at least 1m of free space all around the engine-driven welding
machine.
WARNING!Positiontheengine-drivenweldingmachine
onalevelsurfacewithsufcientload-bearingcapacity,sothatit
cannottoppleorshiftdangerously.
MACHINEEARTHING
To prevent electric shocks caused by faulty user equipment,
the machine must be connected using a xed earthing system and
through the relative terminal.
Fig.G
THEELECTRICCONNECTIONSMUSTONLYBECARRIEDOUT
BYEXPERTORQUALIFIEDTECHNICIANS.
INTERNALCOMBUSTIONENGINE
Regarding:
- checks before use;
- engine starting;
- engine use;
- engine stopping;
refer to the USER MANUAL of the internal combustion engine
producer.
WELDINGCIRCUITCONNECTIONS
WARNING!BEFORECARRYINGOUTTHEFOLLOWING
CONNECTIONS MAKE SURE THE ENGINE-DRIVEN WELDING
MACHINEISSWITCHEDOFF.
The Table (TAB. 1) shows the recommended sizes of the welding
cables (in mm2), according to the maximum current output from the
engine-driven welding machine.
Electrodeholderclamp-weldingcableconnection
There is a special clamp on the terminal that tightens the uncovered
part of the electrode.
Connect this cable to the clamp with the symbol (60A-120A) or
(130A-200A) or (+).
Connectingtheweldingcurrentreturncable
There is a special clamp on the terminal that must be connected to
the workpiece or to the metal bench on which is it positioned, and as
close as possible to the joint being worked.
Connect this cable to the clamp with the symbol
or (-).
Recommendations:
- Screw the welding cable connectors right down into the quick
couplings, so as to ensure perfect electrical contact; otherwise, the
connectors will overheat, wear rapidly and become inefcient.
- Use welding cables that are as short as possible.
- Do not use metal structures that are not part of the workpiece to
substitute the welding current return cable; this could be dangerous
and produce an unsatisfactory weld.
6.WELDING:DESCRIPTIONOFPROCEDURE
- It is essential to refer to the indications of the electrode producer
regarding correct polarity and optimum welding currents (these
indications are generally given on the electrode packaging).
- The welding current should be adjusted according to the diameter
of the electrode used and the type of joint that is to be carried out;
as an indication the following currents can be used for the different
electrode diameters:
ØElectrode
(mm)
Weldingcurrent(A)
min. max.
1.6 25 50
2 40 80
2.5 60 110
3.2 80 160
4.0 120 200
5.0 160 230
6.0 200 330
- Keep in mind that high current levels are used when at welding,
while lower currents should be used with vertical or overhead
welding.
- The mechanical characteristics of the welded joint are determined
by the intensity of the selected current, and also by the other
welding parameters such as arc length, execution speed and
position, electrode diameter and quality (for correct conservation
protect the electrodes from humidity using suitable packages or
containers).
Procedure:
Move the selector to position
(200A AC VERSION only).
- Keeping the mask IN FRONT OF YOUR FACE, rub the electrode
tip on the workpiece as if lighting a match; this is the most correct
method for striking the arc.
WARNING: DO NOT CONTINUALLY TAP the electrode against
the workpiece as this could damage the covering, which makes it
difcult to strike the arc.
- As soon as the arc has been struck, try to keep at a certain distance
from the workpiece, equivalent to the diameter of the electrode
being used. Keep this distance as constant as possible while
welding, and remember that the electrode angle, when moving
forward must, be approx. 20-30 degrees (Fig. H).
- At the end of the weld seam, move the electrode extremity
backwards and position it above the crater to ll; then quickly lift
the electrode from the melted liquid to switch off the arc.
ASPECTSOFTHEWELDSEAM
Fig.I
7. USING THE ENGINE-DRIVEN WELDING MACHINE AS A
GENERATORINALTERNATECURRENT
- Make sure the machine is connected to an earth peg as described
in chapter 5. INSTALLATION.
- Make sure the equipment voltage is the same as the auxiliary outlet
output.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Telwin THUNDER 304 CE HONDA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Telwin THUNDER 304 CE HONDA in de taal/talen: Alle talen als bijlage per email.

De handleiding is 13,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info