781322
47
Verklein
Vergroot
Pagina terug
1/58
Pagina verder
Fuction
ECO mode
Factory setting parameters
55
°C
Basic parameters of system of factory setting
With the system switched off, press the “ECO” and “ON/OFF” keys for 3
seconds and the indicator lights will all go on. And then, the system shall enter
into factory setting mode. 2 seconds later the system will enter into
“Heating/Heat preservation function” state. See the following table for Factory
setting parameters.
7
5. Restore factory settings
Temperature information area
“-” key, adjust the setting temperature
The temperature can be adjusted pressing the “-“ key. Every click will
reduce 10ºC the temperature setting (75-65-55-45-35).
“+” key, adjust the setting temperature:
The temperature can be adjusted pressing the “+“key. Every click will
increase 10ºC the temperature setting (35-45-55-65-75).
“ECO” key:
When the unit has been switched on, press the “ECO” key to enter into the
“ECO” mode. Press “-,+” key and the indicator light of actual temperature
shall go out in order to highlight that the temperature is not adjustable in
the “ECO” mode. The indicator light of 55ºC will flash for 5 seconds later
and then the indicator light of the actual temperature will go on.
Press the “ECO” key again to restore the previous temperature setting.
Press this key for 3 seconds to enter into the SMART CONTROL mode.
The pilot light indicator flash successively around temperatures when the
SMART CONTROL is activated. Press SMART CONTROL bottom for 3 seconds
to exit the SMART CONTROL mode and restore to the previous mode.
a.
b.
after entering the factory setting, press the ECO key again and the
temperature is still 55ºC, because the factory setting parameter is the
default 55ºC (ECO’s temperature is the same as the factory default
temperature)
NOTE
When a dry burning fault occurs, the 3 indicator lights 35, 55 and 75 will flash
at the same time; in case of over-temperature fault, all 5 indicator lights will
flash at the same time; when disconnection or short-circuit of sensor occurs,
the 5 indicator lights will flash from left to right. At this time, all the relays will
be disconnected and the keys will not work. After the fault is removed and the
6. Alarm and fault self-test
47

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Teka EWH 80 VE-D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Teka EWH 80 VE-D in de taal/talen: Engels, Portugees, Spaans als bijlage per email.

De handleiding is 0.97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info