640529
7
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
5
EN
SYMBOLS
This symbol points out the possibility of serious
personal injuries if the provisions and instructions are
not complied with.
This symbol points out that the user must wear
protection goggles when he uses the machine.
This symbol points out that the user must wear
protective gloves when he uses the machine.
This symbol points out the correct running direction of
the machine (grinding wheel)
PART DESCRIPTION (FIG. V)
1. Depth adjustment knob
2. Grinding wheel, 3/16”
3. Front protection
4. Large washer
5. Flange nut
6. Shield guard screw
7. Knob
8. Vise assembly
9. Dressing brick
10. Template
11. Handle bolt
12. Operating handle
13. Rear h ed protection
Note: for spare sarts, see g. VI.
ATTENTION – SETTING UP THE GRINDER
- the grinder shall only be used in a place protected from dust
and dampness, well-lighted, away from children, gases, or
other ammable or explosive liquids. The grinder shall be
placed near a suitable earthed outlet, not to use dangerous
extension cables.
- fasten the grinder onto the bench (photo 1) or to the wall (photo 2)
with two M8 bolts (not provided). For fastening the grinder onto a
bench, carefully position it, using the relevant reference notches.
- when the grinder is fastened onto the bench or to the wall (photo 2)
use a suitable square support (not provided), making sure that the
machine is not fastened at the level of the operator’s eyes. We
recommend that you install the grinder at a max. height of 120 -
130cm from ground level.
- insert screw M6x25 provided, making it slide up to the end of its seat
on the arm (photo 3)
- insert the screw into the slot (photo 3).
- position the rear protection (photo 4A).
- secure the handle on the screw (photo 4B).
- after installing the grinder properly, assemble the wheel.
ASSEMBLY AND WARNINGS ABOUT THE GRINDING
WHEEL
- use a wheel t for the type of chain to be ground, consulting the
chain table enclosed at the end of the handbook (column I - L)
- before using the machine, check that the grinding wheels are
in perfect condition. To do so, hang the wheels by the central hole
and tap them lightly with a non-metal object on the side near the
perimeter. If they are in perfect condition you should hear a metallic
sound. A dull sound means that the wheel is cracked or broken, and
shall be replaced.
- do not force the grinding wheel on the hub and do not modify the
diameter of the assembly hole. Be careful not to use grinding wheels
which do not perfectly match the machine
- to install the wheel, use only clean and perfect hub and ring nut
- make sure that the outside diameters of the hub/ring nut are identical
(g. I)
- the hub is steadily fastened onto the electrical motor’s shaft
- unscrew the ring nut manually, center and install the wheel on the
hub, and re-screw the ring nut manually (photo 5)
- be careful with the ring nut assembly, since its discharge must
be on the wheel side (g. II)
- if the grinding wheel’s ring nut is too tightened, the wheel could
break or disintegrate during operation, seriously damaging the
operator. To avoid this risk, do not overtight, since this ring nut is
made of thermoplastic material
- position the wheel guard properly (foto 6A - 6B), by rotating it till
the notch hits the arm (foto 6C) and secure it with the position lock
screw (foto 6D).
CHECKING THE GRINDING WHEEL
- stand beside the wheel, start the grinder, and examine it to ensure
that it does not oscillate either laterally or transversally, creating any
anomalous vibration
- if the wheel oscillates, immediately stop the machine and make sure
that the wheel has been assembled properly. If necessary, replace
the wheel with an original spare part
- with the machine off, check the wheel prole by means of the special
orange template (g. III point C)
- if necessary, after wearing suitable goggles and gloves, start
the grinder and retouch the wheel prole with the dressing stone
provided, working carefully, grasping the dressing stone with two
hands. The contact with the grinding wheel revolving at high speed
could cause burns and injuries
- before initiating grinding operations, test the assembled grinding
wheel at working speed for at least one minute, keeping far from the
machine and checking that nobody is standing on the trajectory of
its rotation plane.
N.B.: Replace the grinding wheels when their minimum
diameter is about 80mm (3.14 inches)
START-UP
- after fastening the machine onto the bench or to the wall, properly
install the wheel, its guard, and the handle, make sure that the
direction of rotation of the wheel is the one indicated on the wheel
guard; then, start up the machine
- the machine is equipped with a safety switch with a release coil, i.e.
in case of sudden power failure, this switch is deactivated, leaving
the machine on stand-by in case of a sudden return of current (to
restart the grinder, push the switch again)
- the machine must be connected with an outlet that ensures a
230V
~
voltage or to a U.S. outlet that ensures 120V
~
voltage and
10A current
GRINDING
- clean the chain before grinding it
- since this grinder has a xed angle for the wheel inclination, the upper
cutting angle of the tooth is xed at 60° (measured anticlockwise)
- position the chain to be ground on the two jaws, making sure that
the depth gauge is on the right, as indicated (photo 7-points 1)
- loosen the ring nut at the back of the grinder (photo 7 - point 2),
and turn the vise clockwise, considering the grade that corresponds
to the upper grinding angle of the right tooth, using the graduated
scale (photo 7 - point 3)
- make one of the right teeth hit the chain stop, and, with the register
screw (photo 8 - point 1), adjust the tooth feeding
- the chain stop is installed on a pin installed on a plastic connecting
rod. This pin has two position notches, so that the chain stop can be
positioned just at the center of the tooth to be ground
- stop the motor and lower the arm; then, with the chain feed register
screws, try to approach the tooth to the wheel, until it is slightly
touched, always starting from the worst tooth identied using the
template (g. III point D)
- start the grinder and, with the tooth feed register screw, determine
the quantity to be removed
- after determining the quantity to be removed, lock the register screw
with the ring nut (photo 8 - point 2)
- to avoid overloading the motor and to prevent the chain from
being damaged, remove minimum quantities of material and
do not work too long on the same tooth, so as not to damage
the cutter
- adjust the grinding depth with the register screw positioned on the
arm, without nicking connecting links (photo 9)
- after determining the grinding depth, lock the register screw with the
ring nut (photo 9 - point 1)
-
midi jolly
SPEED MASTER
:
adjust the clamping lever; press the red push-button and pull the
lever. The correct tightening of both jaws (photo 10) is set by a
slight clockwise rotation (clockwise rotation increases tightening,
whilst anti-clockwise rotation loosen it). The tightening system
with clamping lever allows a uniform deformation of the two chain
support jaws, so that the chain is always positioned just at the
center of the vise rotation. This is an essential requirement for
perfect grinding, because the length of the right and left teeth
must be the same.
if the clamping lever is turned clockwise, the chain is locked
between the two jaws, for precise and safe grinding (photo 11)
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Tecomec EASY Grinder bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Tecomec EASY Grinder in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info