1. Insert the round base to the back pole (as indicated)
of your LED weather station, turn the base to the right
to secure it in position.
2. Plug the AC/DC adaptor into any 230V European
AC household outlet. Plug the DC jack into the lower
back of the clock. The top front of the clock will show
and the indoor-outdoor temperatures and
weather forecast display will appear. Your LED weather
station is ready to work for you.
Battery Back Up
1. Slide the battery door at the back case, insert 3 x AAA batteries with correct + and - polarity signs inside
the battery compartment. Replace the battery cover.
2. When AC power is off, the batteries will power the clock to keep track of the time and alarm time.
3. When only the back-up batteries is used, the LED panel is off.
Power Up Reception and Signal Strength Display
1. After plug in AC power, the clock starts to receive DCF signal.
Icon blinks. Display shows
2. When strong DCF signal is detected, display shows with 3 bars
When weak or no DCF signal is detected, display shows with 1 bar
or
. You will need to place the clock to another area for better
reception, or unplug the AC/DC jack to start over reception again. During
reception, the signal strength may move from 1 bar to 2 bars to 3 bars. This
is normal since the clock is detecting DCF signal and other signals in the
air at the same time.
3. If the clock does not catch DCF time signal for 7 minutes, it will go back
to normal time display
4. During reception, press TIME button once will go to normal time
display.
Press HR again will return to reception mode and signal strength indication.
Successful reception or failed reception
Icon becomes static on (stop blinking) when reception is successful Icon
disappears when reception is failed
Weak or no RC signal Is
detected
Successful Reception
Automatic Reception and Manual Reception
Automatic reception : this clock starts reception automatically everyday at 1:00am. If auto recpetion fails at
1:00 am, it will start again at 2:00 am. If fails at 2:00 am, it will start again at 3:00 am.
If auto recpetion fails at 3:00 am still fails, it will start reception every 3 hours until it succeeds to catch correct
DCF time.
Manual reception : press HR button once anytime to start manual reception of DCF time signal. The LED time
display will go to radio controlled reception mode
To Set Time and Alarm Time
After power up, if press TIME button once, time digits go to 0:00 am (default
start-up time). The clock continues to receive DCF signal. The icon is st
ill
blinking.
Press HR button once will go back to radio controlled reception mode (as above)
TO SET TIME
Press and hold TIME button and at the same time press HR button once at a time
to set hour.
Press and hold TIME button and at the same time press MIN button once at a time
to set minute.
SET ALARM 2
TO SET ALARM 1 TIME
1. Slide the Alarm Switch to ALM 1.
2. Press and hold ALM button and at the same time press HR button once at a time to set hour.
3. Press and hold ALM button and at the same time press MIN button once at a time to set minute.
TO SET ALARM 2 TIME
1. Slide the Alarm Switch to ALM 2.
2. Press and hold ALM button and at the same time press HR button once at a time to set hour.
3. Press and hold ALM button and at the same time press MIN button once at a time to set minute.
TO TURN ON/OFF ALARM 1 or/and ALARM 2
1. To turn on Alarm 1 only, slide the alarm switch to ALM 1, ALM 1 LED lights up on upper left of the hour
digits.
2. To turn on Alarm 2 only, slide the alarm switch to ALM 2, ALM 2 LED lights up on lower left of the hour
digits.
3. To turn on both Alarm 1 and 2, slide the alarm switch to ALM 1 + 2, both ALM 1 and ALM 2 LED light up.
4. To in-activate both Alarm 1 and 2 permanently, slide to ALM OFF. Both ALM 1 and ALM 2 LED turn off.
TO USE THE SNOOZE ALARM
When time reaches the set ALARM 1 and/or ALARM 2 time, the clock will beep with the ALM 1 and/or ALM 2
LED blinking.
Press the SNOOZE button once, the alarm sound will stop and ALM 1 or ALM 2 LED keep blinking. Alarm will
sound againin 5 minutes.
TO STOP THE ALARM
When time reaches the set ALARM 1 and/or ALARM 2 time, the clock will beep with the ALM 1 and/or ALM 2
LED blinking.
Press and hold the SNOOZE button for 2 seconds, the alarm sound will stop and ALM 1 or ALM 2 LED
becomes static. Alarm 1 and/or Alarm 2 will sound again same time next day.
TO TURN OFF ALARM 1 AND/OR ALARM 2 PERMANENTLY
Slide the alarm switch to ALM OFF. Alarm sound will stop and both ALM 1 and ALM 2 LED's turn off.
TO SET SNOOZE DURATION (from 5 to 60 minutes)
Press and hold SNOOZE and time display will show "05" (default snooze duration) and then press MINUTE
button to set your desired snooze duration.
TO READ MAXIMUM-MINUMUM INDOOR-OUTDOOR TEMPERATURES
Simply press the button to view the maximum indoor and outdoor temperatures. Press MAXCLEAR to reset the
Max readings. The readout will now appear as — and will start to record the maximums again.
Then press the button to view the minimum indoor and outdoor temperatures. Press MAXMINCLEAR to reset the
Min readings. The readout will now appear as — and will start to record the minimums again.
IF YOU LOSE THE OUTDOOR TEMPERATURE
When the outdoor temperature digits show '—--", the wireless transmission is either interrupted or lost. Press the
CLEAR button at the back of your LED weather station, then press RESET button at the back of the outdoor
transmitter. If you continue to lose the outdoor temperature display, try placing the transmitter in a different
location until you have smooth transmission of temperature data.
USING THE WEATHER FORECASTER AND BAROMETER
Your LED weather station has a built-in barometer which measures the barometric pressure. After power up,
the display shows Sunny & Cloudy icons. Your LED weather station takes around 24 hours to gather data of
barometric pressure changes and predicts next 12-24 hours weather conditions.
There are four types of weather display of the predicted weather condition :
TROUBLE SHOOTING
Press the RESET button on the back of the base thermometer and then press RESET button located on the
back of the outdoor transmitter. Once you do this, your clock will be reset to default setting and needs to be
up-dated by DCF time signal again.
TO USE THE HI-LO DIMMER SWITCH
Simply slide the LO-HI DIMMER switch at the back of the clock to adjust the LED brightness to a comfortable
level to you in the dark.
CARE OF YOUR CLOCK
1. Do not expose your clock to extreme temperatures, water or direct sunlight.
2. Avoid contact with any corrosive materials
3. Do not subject the clock to excessive force, dust or humidity
4. Do not open the inner back case or tamper with any components of this clock
5. Do not plug in any other AC/DC adaptor with incorrect specifications or voltage
6. Do not place your clock in range of strong interferences. (TV, Microwave…)
SUNNYSUNNY & CLOUDYCLOUDYRAINY
Your weather forecaster also has weather tendency indicator, when the air pressure is going up (the weather will
improve) the UP arrow will appear, when the air pressure is going down (the weather will go worse) the DOWN
arrow will appear.
Remarks : Moving your weather station around your house or your building will affect its accuracy because the
sudden change of temperature or height/altitude will affect the accuracy of your weather station. It
will take 24 hours to get stable again to predict next 12-24 hours weather condition.
Your weather station predicts next 12 - 24 hours weather conditions. It may not match with the current weather
condition outside.
Instruction Manual
WS 6830
RC tower Icon blinking
Strong DCF signal is detected,
Minute digits may start counting
01,02,03...60,00,01,02.... trying
to match with the correct seconds
DfJJY signal
Failed Reception
SET ALARM 1
Hulp nodig? Stel uw vraag in het forum
Misbruik melden
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Techno line WS 6830 bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Techno line WS 6830 in de taal/talen: Engels als bijlage per email.
De handleiding is 0,66 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
