486998
12
Verklein
Vergroot
Pagina terug
1/35
Pagina verder
Generated by Unregistered Batch DOC TO PDF Converter
2011.3.804.1511, please register!
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International
BELGIUM. The page must reproduced and folded in order to
obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).
The page must be folded in order to keep the good numbering
when you turn the page of the I/B . Don’t change the page
numbering. Keep the languages integrity.
12
Assembly page 12/35
Fax +32 2 359 95 50
OUTLINING
Outlining requires no attachments. Take the clipper and push the lever up to the close-cut
position.
Comb hair into the required style. Position clipper between the sideburns and the ear. Make sure
the outer edge of the blade is against the hairline. With the outline of the hair as your guide,
slowly move the clipper around the ears (6). For the back of the neck and the sideburns, hold the
clipper upside down (7), and move downwards holding it against the skin at the length desired.
SHORT CUTS
Always cut from the back of the neck to the crown, using the longest attachment comb. Holding
it flat against the head, slowly move the clipper up through the hair. Use the same technique for
the sides, cutting from the bottom to the upper side of the head (8).
For the front of the crown, cut the hair against the direction in which it grows. Then even it up
with the sides (9).
For a flat top, use a flat comb, not the attachment comb. Just cut hair on top of the head over it.
To taper hair down to the neckline, use closer cutting attachment combs. Comb hair, check for
uneven spots and outline sideburns and neckline (10).
The four basic areas illustrated are your "road map" to easy do-it-yourself hair cutting (11).
MAINTENANCE
Your clipper was carefully examined before leaving our factory to ensure that the blades were
oiled and aligned.
Blades must be realigned if they have been removed for cleaning or replacement. To realign the
blades, simply match the upper and bottom blades teeth up, point for point. The end of the top
blade teeth should be approximately 1.2 mm away from bottom blade. Compare your clipper
blades with the sketch (12).
If the blade alignment is incorrect, add a few drops of oil to the blades, turn clipper on for a few
moments, turn off and unplug. Loosen screws slightly and adjust. Tighten screws once the blades
are aligned (13).
Change the blades as soon as they become blunt.
ADJUSTABLE LEVER
The lever will extend the lifespan of your blades since a different cutting edge is used in each
setting. In addition, if extremely heavy hair cutting has jammed the blades, it will help you
remove hair that has become wedged between the two blades without removing them. While the
clipper is running, rapidly move the lever from "close cut" to "longer cut" a couple of times (14).
The lever is conveniently located near your thumb. When the lever is in the uppermost position,
the blades will give you the closest cut and leave the hair very short. Pushing the lever
downward gradually increases the cutting length.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Team HC 9 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Team HC 9 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info