506486
7
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
1
1.CONTENTS
1. Contents .................................................................................................................. 1
2. Control location ........................................................................................................ 3
3. Before riding ............................................................................................................ 4
4. Safe riding ............................................................................................................... 4
5. Driving ..................................................................................................................... 5
6. Use genuine spare parts .......................................................................................... 5
7. Use of each component ........................................................................................... 6
Gauges .................................................................................................................... 6
Operation of ignition switch ...................................................................................... 7
Operation of steering handle lock switch .................................................................. 7
Operation of seat open switch .................................................................................. 7
Use of buttons ......................................................................................................... 7
Storage box ................................................................................................................. 9
Safety helmet hook .................................................................................................... 10
Fuel tank cap ........................................................................................................... 10
Brake....................................................................................................................... 10
8. Important points and cautions for starting engine ................................................... 11
9. The best way to drive off ........................................................................................ 12
The control of throttle valve handle ......................................................................... 12
Parking method ..................................................................................................... 12
10.Inspection and maintenance before riding ............................................................... 13
Routine inspection ................................................................................................. 13
Engine oil inspection and change ........................................................................... 13
Fuel inspection ........................................................................................................ 14
Transmission oil inspection and change ................................................................... 14
Inspection and adjustment of brake free play .......................................................... 15
Disc brake inspection (depending on models) ......................................................... 16
Throttle valve handle clearance adjustment ............................................................ 17
Inspection and maintenance of battery ................................................................... 17
Tire inspection ....................................................................................................... 18
Steering handle front shock absorbers inspection ................................................... 18
Checking and changing fuses ................................................................................. 19
Checking the turn signal lights and horn ................................................................. 19
Checking the front and rear lights ........................................................................... 19
Checking the brake light ......................................................................................... 19
2
1.CONTENTS
Checking for fuel leakage ........................................................................................ 20
Checking the lubrication of body’s various mechanisms .......................................... 20
Checking the spark plug ......................................................................................... 20
Checking the air cleaner ......................................................................................... 20
11. When there is an abnormal condition or a trouble ................................................... 21
Diagnosis when engine does not start ..................................................................... 21
12. C.D.I. electrical ignition system ............................................................................... 21
13. Suggestions on engine fuel ..................................................................................... 21
14. Transmission oil ..................................................................................................... 21
15. Cautions for riding motorcycle ................................................................................ 22
16. Periodical maintenance schedule ............................................................................... 23
17. Specification ........................................................................................................... 24
18. Electrical Diagram ................................................................................................... 25
3
2.CONTROL LOCATION
MODEL: ORBIT II 125AE12W1-6
Fuel tank cap
Light/Starter switch
Exhaust Muffler
High &Low beam
/Passing/
Turn signal/Horn switch
Front brake level
Tail light
Fuse /CDI
&Battery
Air Cleaner
Oil level
Front turn
signal light
Helmet hook
Storage box
Kick starter pedal
Main stand
Ignition switch
Rear brake level
Engine start
control switch
Side stand
Front light /
Position light
Rear turn
signal light
Engine number
Frame number
4
3.BEFORE RIDING
This manual describes the correct usage of this motorcycle including safety riding, simple inspection methods
and so on.
For a more comfortable and safety riding, please read this manual carefully.
For your benefit, please ask your SYM dealer the operating manual and carefully read the following:
Correct use of the motorcycle.
Pre-delivery inspection and maintenance.
Thank you very much for your patronage
In order to maximize your motorcycle’s performance, a periodical inspection and maintenance should be
completely carried out.
We recommend that after riding your new motorcycle for the first 300 kilometers, you should take your
motorcycle to the original dealer for an initial inspection, and to have your motorcycle inspected
periodically every 1000 kilometers thereafter.
In case the motorcycle’s specifications and construction are modified and different from the photos and
diagrams on the owner’s manual / catalogues, the specifications and construction of the actual
motorcycle shall prevail.
4. SAFE RIDING
It is very important to be relaxed and clothe properly when driving, observe traffic regulations, do not rush, always
drive carefully and relaxed.
Usually, most people would ride their newly bought motorcycle very carefully, but after they became familiar with
their motorcycles, they tended to become reckless which may result in an accident.
To remind you:
Please wear a safety helmet, and properly tighten the chin belt when riding a motorcycle.
Clothes with open or loose cuffs may be blown by wind and cause the cuffs to get caught on the
steering handle and thus affects riding safety.
So, put on clothes with tight sleeves.
Hold the steering handle by both hands when riding. Never ride with only one hand.
Observe the speed limit.
Wear suitable low-heel shoes.
Perform periodical maintenance and inspection in accordance with the schedule.
WARNING!!
To avoid getting burned by exhaust pipe when taking a passenger. Make sure your passenger has put
his/her feet on the pedals.
After running, the exhaust pipe is very hot, be careful not to get burned when conducting an inspection or
maintenance.
After running, the exhaust pipe is very hot, select a suitable location to park your motorcycle to avoid
others getting burned by the exhaust pipe.
CAUTION:
Modified motorcycle will affect its structure or performance, and cause poor engine operation or exhaust
noise, which will result in shortening the motorcycle’s service life.
Besides, modification is illegal and does not conform to the original design and specifications.
A modified motorcycle will not be covered by warranty; therefore, do not modify your motorcycle at will.
5
5.DRIVING
Keep the related parts of your body such as arms, palms, lumbar, and toes relax and ride with
the most comfortable posture in order to be able to react quickly whenever it is necessary.
Rider’s posture will greatly affect riding safety. Always keep your body’s gravity in the center of the
saddle, if your body’s gravity is on the rear part of saddle, the front wheel load will be reduced, and this
will cause the steering handle shaking. It is dangerous to ride a motorcycle with an unstable handle.
It will be much easier to make a turn if rider inclines his body inward when turning. On the other hand,
the rider will feel unstable if his body and the motorcycle do not incline.
The motorcycle is hard to control on a bumpy, unleveled, unpaved road, try to know the road conditions in
advance, slow down and use your shoulder’s force to control the handle.
Suggestion: Do not load objects on the front pedals unnecessarily, to avoid affecting the riding safety and
the operation of steering handle.
CAUTION:
The rider’s feeling on the handle is slightly different with a load or without a load.
Overload may cause the handle to swing and affects the riding safety.
Therefore, do not overload your motorcycle.
CAUTION:
Do not place flammable materials such as rags between the body side cover and engine to avoid
components damaging by fire.
Do not load objects on areas not specified for loading to avoid damage.
SUGGESTION
To maximize the motorcycle’s performance and prolong its service life:
The first month or first 1000km is the wear- in period for the engine and components.
6. USE GENUINE SPARE PARTS
In order to maintain the motorcycle’s best performance, each part’s quality, material, and machined precision
must conform with the design requirements. “SYM Genuine Spare Parts” were made from the same high
quality materials used for the original motorcycle. No parts would be sold to the market until they could meet
the designed specifications through sophisticated engineering and stringent quality control. Therefore, it is
necessary to purchase “SYM Genuine Spare Parts” from “SYM Authorized Dealers” when replacing
spare parts. If you buy cheap or fake substitute parts from the market, no guarantee can be provided either
for the quality or durability. Also, it may result in unexpected troubles and lower the motorcycles
performance.
Always use SYM Genuine Spare Parts to keep your motorcycles pure blood and to ensure its long
service life.
6
7.USE OF EACH COMPONENT
(The following is SYM 4 stroke air-cooling 125 c.c. scooter’s basic operation, and they
could vary from different individual models. Please consult the end of this manual.)
§GAUGES §
The panel figure for speedometer may vary from model to model, but the location usually are the
same.
CAUTION:
Do not wipe plastic components, e.g. instrument panel, headlight, with organic solvents such as
gasoline…etc to avoid damaging these components.
Speedometer
Indicates driving speed.
Odometer
Indicates total accumulated distance traveled.
High Beam Indicator
This indicator comes on with high beam headlight
is turned on.
Turn (left/right) Signal Indicator
The left or right Indicator will be flashing
according to the operated directions of turn signal
light switch when it is turned on.
Fuel Meter:
The pointer in this meter shows how much fuel
remains in the tank.
The pointer stays in “E” position when key switch
is turned to “OFF”.
Fuel meter
Odometer
Speedometer
Turn Right
Signal Indicator
Turn Left
Signal Indicator
High Beam
Indicator
7
§OPERATION OF IGNITION SWITCH §
“ON” position:
Engine can be started in this position.
Ignition switch key can not be removed.
“OFF” position:
Engine is shut off and can not be started in this position .
Ignition switch key can be removed.
§OPERATION OF STEERING HANDLE LOCK SWITCH §
“Steering handle lock” position
Turn the steering handle to left and insert the key into,
press ignition switch key clockwise and then lightly turn it
to left to the “lock” position.
The steering handle is locked in this position.
Ignition switch key can be removed.
When unlocking, simply turn the key from the “LOCK”
position to the “OFF” position.
§OPERATION OF SEAT OPEN SWITCH§
“Fill gasoline lock” position
Inserted the ignition switch key in the main switch lock.
Turn the ignition switch key to thefill gasoline position counter-clockwise.
Then, the seat will be open. You can fill gasoline in the fuel tank.
CAUTION:
Never operate the ignition switch key when the motorcycle is running. To turn the ignition switch to
“OFF” and “LOCK” position will shut off the electrical system and that may result in a dangerous
accident. Therefore, the ignition switch can only be turned off after the motorcycle has been
completely stopped.
Always remove the key and be sure to take the key away with you after locking the steering handle
before leaving your motorcycle.
If ignition switch remains in the “ON” position for a prolonged period after the engine has been
stopped, the battery’s capacity will be reduced and this may affect the engine’s start ability.
Make sure to take the key away with you before you lock your seat.
§USE OF BUTTONS §
IGNITION SWITCH
CAUTION:
Make sure to take the key
away with you before you
lock your seat.
Light switches
Electrical starter
button
Horn Switch
Turn Signal Switch
Seat open
High/low beam
switch
8
Light Switches
When the switch is turned to this position as the engine is being started, headlight, rear light,
instrument panel light, and position light will come on. This is the high beam of headlight switching
switch.
When the switch is turned to this position as the engine is being started, rear light, instrument panel
light, and position light will come on.
When the switch is turned to this position, all lights will go off.
Electrical starter button
This is a starting motor button (switch) for engine starting.
With the main switch on, press this button while holding the front or rear brake lever will start the
engine.
CAUTION:
Release this button immediately after engine has been starter, and never press the button again to
avoid damaging the engine.
This mechanism is a safety design. The engine can only be started after the front or rear brake lever
(pedal) has been applied.
Do not use light system. Turn headlight and turn signal light to the “off” position when the engine is
being started.
High/low beam switch
This is the high and low beam of headlight switching switch. Press this switch to switch between high and
beams.
This is for high beam.
This is for low beam.(please turn to low beam riding in city.)
Seat open switch
Turn ignition switch to theON position and press this button down. Then, the seat will be
open.
This button will return to original position after
releasing.
Press the seat down and it will be locked
automatically.
After the seat catch has been locked , check to
make sure it has locked properly by lightly lifting the
seat.
Seat open
switch
CAUTION:
Be sure to remove the key after the seat has been
locked.
Do not put the key inside the storage box after
unlocking to avoid the key being locked inside the
storage box when the seat is pressed down
automatically.
9
Engine start control switch
The switch button position is under seat.
ON position: Engine is locked and can not be started engine in this
position.
OFF position: When the ignition switch is on position, the start
control switch is off position, press electrical starter
button while holding the front or rear brake lever will start
the engine.
Horn Switch
Press this button down when ignition switch is in the ON position, the horn will sound.
Turn Signal Switch
Turn signal lights are used when turning left/right or changing lane.
Turn ignition switch to the ON position, and slide the turn signal switch to left or right . Then, the turn signal
lights will flash.
To release, simply return the turn signal light button to the original position.
Right-side turn signal light flashing means you intend to make a right turn.
Left-side turn signal light flashing means you intend to make a left turn.
§STORAGE BOX§
This box is located under the seat.
Maximum load capacity:5kg.
Do not store valuables in the box.
Make sure that the seat has been locked completely after it was
pressed down.
Take out valuables before washing to avoid wetting these objects.
Do not place thermal sensitive objects in the box because of engine’s
heat and high temperature.
Engine start
control switch
Storage box
10
§SAFETY HELMET HOOK§
Stop the motorcycle, and hook the safety helmet chin belt the
hook.
§FUEL TANK CAP§
1.Insert the key into the main switch and open the seat, and turn the fuel cap anticlockwise, then the cap
can be removed.
2. Do not fill above the fuel upper limit when refueling.
3. Align the mark on the cap with the mark on the fuel tank, then turn the fuel cap clockwise and
lock the seat.
CAUTION:
Main stand should be put down on the ground, engine should be shut off and flames should be
strictly prohibited to ensure safety when refueling.
Do not fill above fuel upper limit when refueling. Otherwise, fuel will flow out through a hole on the
cap that may damage the bodys painting, in serious cases; it serious cases; it may cause a fire to
burn down the motorcycle.
Make sure the cap has been tightened properly.
§BRAKE§
Avoid unnecessary sudden braking.
Use front and rear wheel brakes simultaneously when braking.
Avoid brake continuously for a long period of time because that may overheat the brakes and reduce its
braking efficiency.
Slow down and brake early when riding in rainy days on slippery roads. Never apply the brakes
suddenly to prevent skidding and falling.
Using only the front brake or the rear brake increases the risk of falling because the motorcycle is tend to
pulled to one side.
Engine Brake
Return the throttle valve handle back to its original position, and apply engine brake.
It is necessary to apply brake both for front wheel and for rear wheel intermittently when riding on a long or stiff
slope.
CAUTION:
Do not hang the safety helmet onto this hook when riding to
avoid damaging motorcycle and loosing safety helmet’s
function.
hand-brake type
For Front Wheel
For Rear Wheel
Hook
11
8.IMPORTANT POINTS AND CAUTIONS FOR STARTING ENGINE
CAUTION:
Please check the oil and fuel volume are adequate or not before starting the engine.
To start the engine the main parking stand must be firmly on the ground and the brake is applied on
the rear wheel to prevent the motorcycle from moving forward suddenly.
1.Turn ignition switch key to the ”ONposition.
2.Apply hand(foot) rear wheel brake.
3.Do not accelerate, press starter button when the brake is applied.
We care for you! Before drive off, keep the hand brake applied on the rear wheel.
CAUTION:
If engine can not be started after press the kick starter arm for 3~5 times, turn the throttle valve
handle 1/8~1/4 turns, and then press the kick starter arm again for an ease start.
In order to avoid damaging the starter motor, please do not press the starter button continuously over
15 seconds.
If engine still can not be started after pressing starter button over 15 times, stop and wait for 10
seconds before start it again.
It is harder to get the engine started after the motorcycle has been left idle for a long time or after
refueling only after the fuel has been depleted. Then, it is necessary to press starting lever or starter
button several times, and keep the throttle valve handle at the close position to start the engine.
It may need several minutes to warm up engine if it is a cold start.
Exhaust contains harmful gases (CO), therefore please start the engine at a well ventilated place.
When starting engine with starting lever.
After step 1~3 is completed, press the kick starter forcefully by foot with the throttle valve handle at the
close position.
If engine is cold and it is difficult to start, rotating the throttle valve 1/8~1/4 turns will make the start
easier.
Put the kick starter back to its original position after the engine has been started.
CAUTION:
Firmly support the motorcycle with the main parking stand before starting the engine with the kick
starter arm.
Starter engine with the kick starter arm occasionally to prevent it from loosing its function because of
unused for a long time.
1/4
1/8
12
9.THE BEST WAY TO DRIVE OFF
turn on the turn signal light before moving, and make sure no vehicle is coming from behind. Then, drive off.
§THE CONTROL OF THROTTLE VALVE HANDLE §
Acceleration : To increase speed. When riding on an inclined road, turn the throttle valve handle slowly to
allow the engine to output its power.
Deceleration : To decrease speed.
§PARKING METHOD §
when approaching the parking lot:
1. Turn on the turn signal light early, and pay attention to the vehicles in front, from rear, left and right, then
take the inner lane and approach slowly.
2. Return the throttle valve handle back to its original position, and apply brakes in advance. (Brake light comes
on when braking to warn drivers of vehicles behind.)
When stop completely:
3. Press the turn signal switch back to its original position, and turn the ignition switch key to the “OFF”
position to shut off the engine.
4. Get off the motorcycle from left side after the engine has been stopped, and select a parking place where
the motorcycle will not interfere with traffic and the ground is level, then put down motorcycle’s main
parking stand.
5. Hold the steering handle with your left hand, and hold down the front end of saddle or hold the parking
handle on the lower-left side of saddle with your right hand.
6. Press the main parking stand with your right foot, put down the main parking stand firmly on the ground.
To remind you: Lock the steering handle and remove the key after parking to prevent the motorcycle from
being stolen.
CAUTION:
Park your motorcycle at a safe place where it will not interfere with traffic.
Deceleration
Acceleration
13
10.INSPECTION AND MAINTENANCE BEFORE RIDING
(Please refer to the components location diagram for the following components.)
§ROUTINE INSPECTION §
Check Items Check Key Points
Engine Oil Is there enough engine oil?
Fuel Is it enough? Is it Octane 90 or above
Brake Front
Braking condition?
(Brake lever free play: 10~20mm)
Rear
Braking condition?
(Brake lever free play: 10~20mm)
Tires Front
Is tire pressure normal?
(Standard: 1.75kg/cm
2
)
Rear
Is tire pressure normal?
(Standard: 2.0 kg/cm
2
for 1 person, 2. 25 kg/cm
2
for 2 persons)
Steering Handle Does the handle vibrate abnormally or is difficult to turn?
Speedometer, lights, and rearview
mirror
Is it operated properly?
Do lights come on? Can it be seen clearly from behind?
Tightness of Main Components Are screws, nuts loosen?
Abnormal Points Do the previous troubles still exist?
CAUTION:
If any problem founded during routine inspection, correct the problem before using the motorcycle
again, have your motorcycle checked and repaired by the “SYM dealer or authorized service
personnel” if necessary.
§ENGINE OIL INSPECTION AND CHANGE §
INSPECTION:
1. Use the main parking stand to support the motorcycle on a
level ground, remove the dipstick after engine stopped for 3~5
minutes. Wipe oil off the dipstick and then insert it into the
guide tube again (Do not rotate it.)
2. Remove the dipstick and check whether oil level is in between
the upper and lower marks.
Add oil to upper limit if oil is under the lower limit. (Check
cylinder, crankcase…etc for leakage.)
14
OIL CHANGE:
Change engine oil after the first 300km, and change the
engine oil every 1000km thereafter.
In order to maintain the engine’s maximum performance,
check whether the engine oil is enough every 500km.
Add oil to upper limit if the engine oil has been found to
be inadequate.
Engine Oil : Use SL/CFSAE 10W-30 grade or better
engine oil. Otherwise, damage will not be covered by
warranty.
Oil Capacity : 0.95 Liter (0.70 liters for routine change).
Use SAE 5W-40 when outside temperature is below 0.
Oil Filter Cleaning
The oil filter nut assembly of the element, and remove the
element. Remove the foreign materials from the element by
using a gasoline or air spraying gun.
WARNING:
Oil level will not be correct when checking the oil level
with the motorcycle parked on an unleveled ground or
immediately after the engine stopped.
Engine and exhaust pipe are hot right after engine
stopped. Pay special attention not to get burned when
checking or replacing engine oil.
If the oil lever approaches lower limit again after refilled,
check the engine for leaks and refill it again.
Keep away from spark and flames when refilling the oil.
§FUEL INSPECTION§
Turn main switch key to “ON” position, and check fuel gauge’s needle range to make sure there is
enough amount of fuel in the fuel tank.
This motorcycle’s engine is designed for using the unleaded fuel of Octane 90 or above.
Firmly secure the main stand on the ground, shut off the engine and keep flames away from the
motorcycle when refueling.
Do not fill above fuel upper limit lever when refueling.
Make sure the fuel tank cap had been tighten properly.
§TRANSMISSION OIL INSPECTION AND CHANGE§
INSPECTION:
Use the main stand to support the motorcycle on a level ground, after the engine stops, wait for 3~5
minutes. Remove the transmission oil infusion bolt, put a measuring glass under the drain bolt, and
remove the drain bolt. Let the oil flows into measuring glass and check for decreased or not. (at
disassembly:180~185c.c./at change:165~170c.c.).
OIL REPLACEMENT:
stop the engine and use the main stand to support your motorcycle on a lever ground. Remove the
infusion bolt and drain bolt, drain out the oil.
Install the drain bolt and tighten it. Fill new transmission oil (165~170c.c.), and install the infusion bolt
and tighten it. (Make sure that bolts are tightened and check that there’s no leakage.)
Recommend Oil: Genuine SYM HYPOLD GEAR OIL (SAE 85W-140).
Upper limit
Oil filter
Filter nut
Lower limit
15
§INSPECTION AND ADJUSTMENT OF BRAKE FREE PLAY§
INSPECTION: (Brake lever free play must checked with the engine shut off.)
Brake lever and pedal free play for front and rear wheels.
If checking the hand-braking lever for front wheels, its free play (the stroke of hand-braking lever from no
braking to initial braking) should be 10~20mm. It is abnormal if the feel is spongy when holding the
hand-braking lever forcefully.
Adjustment:Drum type
The indentation of brake adjustment nut must be aligned with the pin. (see below figure)
Turn the adjustment nut on brake arm of front and rear wheels to adjust the free play of hand-brake lever.
Hold the hand-brake levers after adjusting with both hands until there is effective brake feeling.
Measure the free play with a ruler.
Pin
Adjustment nut
CAUTION:
When free play is between 10~20 mm, check brake
indicators of front and rear wheels. If the arrow on the
brake arm aligned with the” marked on the brake disk,
that means the brake lining has been excessively worn,
and must be replaced immediately.
To decrease
free play
To
increase
free play
Adjustment nut
Rear Wheel drum type
Front wheel drum type
10~20 mm
Rear Wheel hand-brake type
16
§DISK BRAKE INSPECTION§
Visual check brake lines for leakage, or damage, check brake
lines connections for looseness using a wrench or similar tool,
and check whether steering handle vibration in driving, or any
parts interference may have damage the brake lines. If so, bring
your motorcycle to your SYM dealer for repairing or service.
leak, damaged, looseness of brake line
Checking front brake lining
check the brake from behind the brake caliper.
The brake pad must be replaced with new lining
when the brake pad wear limit reaches the
brake disk.
Checking oil quantity in brake oil reservoir
Park the motorcycle on a lever ground, and
check if fluid lever is under the “LOWER” mark.
Recommended Brake Fluid: WELL RUN
BRAKE OIL (DOT 3).
Replenishment of front wheel brake fluid
1.Loosen the screws and remove the master cylinder cover.
2.Wipe clean foreign materials, dirt around the reservoir,
being careful not to let foreign materials fall into the
reservoir.
3. Remove the diaphragm plate and the diaphragm.
4. Add brake fluid to upper lever.
5.Install the diaphragm plate and the diaphragm, and install
the master cylinder cover.
5. please note the diaphragm direction, and do not let foreign
materials fall into the reservoir. And tighten the master
cylinder cover securely.
CAUTION:
TO prevent chemical reaction, please do not use brake fluids other than those recommended.
Do not fill above the upper limit when adding brake fluid and avoid dropping on painting or plastic
components to prevent damage.
CAUTION:
Please drive your motorcycle on a dry road surface
slowly and operate front and rear brakes in order to
find out if there is any malfunction so as to ensure the
motorcycle is at optimum condition and safe ride.
Brake
disk
Brake
caliper
Brake
pad wear
limit grooves
Screw
Master cylinder
cover
Diaphragm
Upper
Brake fluid
17
§THROTTLE VALVE HANDLE CLEARANCE ADJUSTMENT §
Correct clearance allows throttle vale handle to rotate
2~6mm.
Loosen the lock nut first, then turn the adjust nut to adjust.
Tighten the lock nut securely when finished.
§INSPECTION AND MAINTENANCE OF BATTERY §
The motorcycle is equipped with a maintenance-free type battery, so it is unnecessary to check and add
electrolyte. Have your motorcycle checked by SYM Authorized Dealer should any abnormality is found.
Cleaning of battery terminals
Remove the battery terminals and clean if there are dirt
and corrosion on them.
Battery removal procedures are as follows:
Turn ignition switch key to the “OFF” position, then
remove negative cable screw firstly and disconnect
the negative cable. Then, remove positive cable screw
and positive cable.
CAUTION:
Clean the battery posts with warm water if the posts are eroded and have some white powders on
them.
If there is an obvious erosion on the terminals, disconnect the cables, and then clean the erosion off
with a steel brush or a piece of sandpaper.
Install battery cable after cleaning and apply a thin coat of grease on the terminals.
Install battery in reverse order of removal.
The motorcycle is equipped with a maintenance-free type battery, so it is unnecessary to check and add
electrolyte. Have your motorcycle checked by SYM Authorized Dealer should any abnormality is found.
CAUTION:
This is a closed type battery. Never remove the caps.
In order to prevent electric leakage and self-discharge when the battery sits idle for long periods.
Remove battery from motorcycle; store it in well-ventilated and dimly lighted place after the battery has
been fully charged. Disconnect battery’s negative cable if the battery is still kept on the motorcycle.
If the battery needs to be replaced, replace with a same closed-type battery (Maintenance-Free).
Check Items:
1. Check throttle valve cable to see if it can be moved smoothly
from a closed position to a wide open position.
2. Rotate steering handle from side to side to check if the
throttle valve cable is interfered.
3. Check to see if the throttle valve cable is obstructed by other
cables preventing it from being operated smoothly.
2~6 mm
Lock nut
Adjust nut
Negative
Positive
18
§TIRE INSPECTION §
Tires should be checked and inflated with the engine shut off.
If a tire’s ground contacting curve is abnormal, check it with an air pressure gauge and inflate it to the
specified pressure.
Tires pressure must be checked with an air pressure gauge when cold.
Visual check tires for frontal and lateral side walls for
crack or damage.
Visual check tires for any nails or small stones wedged
in the tread.
Check the “tread wear indicator” condition to see if tread
groove depth is insufficient.
A tire with a wear bar showing is worn out and should be
replaced immediately.
CAUTION:
Abnormal tire pressure, wear, or crack is the most important cause that results in the loss control of
the steering handle and a punctured tire(s).
§STEERING HANDLE FRONT SHOCK ABSORBERS INSPECTION §
Perform this check with engine shut off and ignition switch key
removed.
Visual check front shock absorbers for damage.
Operate steering handle up and down, and check front shock absorbers
for noises due to bends.
Check the bolts and nuts of front shock absorbers with wrenches for
tightness.
Shake steering handle up & down, left & right, and front & rear to check
if it is loosen, has too much resistance and pulls to one side.
Check steering handle if it is being pulled too tight by the brake cables.
Take your motorcycle to SYM Authorized Dealer for a check or
adjustment if any abnormal conditions are found.
PLEASE REFER TO SPECIFICATIONS FOR STANDARD TIRE PRESSURE
Tread wear
indicator
Crack and
damage
Foreign materials
(nails or small
stones)
19
§CHECKING AND CHANGING FUSES §
Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one having the
same specified amperage rating (7A). Using a fuse of more than 7 amperes, a brass or iron wire to replace a
blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.
Remove the storage box, and you’ll find the fuse holder near battery.
Open the fuse box cover, and pull out the fuse. Check it for damage or broken.
Fuses must be firmly secured with wire connectors when replacing. Loose connections will result in
overhead and damage.
Use only parts having the specified specification to replace electrical components such as light bulbs.
Using parts not having the specified specifications for replacement may cause the fuse to blow and
over-discharge the battery.
Avoid spraying water directly on or around fuse box when washing the motorcycle.
If the new fuse burn out quickly again, please check the faulty reason before replace it again. Take your
motorcycle to your dealer for an inspection if a fuse is blown by unknown causes.
§CHECKING THE TURN SIGNAL LIGHTS AND HORN §
Turn the ignition switch key to the “ON” position.
Turn on the turn signal light switch, and make sure that the front & rear and left & right signal lights flashes
and also check if the warning buzzer sounds.
Check turn signal light covers if they are dirty, crack, or loosen.
Press horn button to check if it works.
CAUTION:
Specified specification bulbs should be used for turn signal lights. Otherwise, the normal operation
of turn signal lights will be affected.
Turn on the turn signal light before turning or switching lane to warn driver of vehicles behind.
Turn off the turn signal light immediately by pressing its button down after using. Otherwise, the
flashing of twin signal lights may confuse the drivers of vehicles behind.
§CHECKING THE FRONT AND REAR LIGHTS §
Start engine the head lamp is turned on automatically. Check if head lamp and rear lamp come on.
Check the brightness and direction of front light by wall to see if it is correct.
Check the head lamp cover if it is dirty, crack, or loosen.
§CHECKING THE BRAKE LIGHT §
Turn the ignition switch key to the “ON” position, hold the hand-braking levers for front and rear wheels.
Check if the brake lights come on.
Check the brake light cover if it is dirty, crack, or loosen.
CAUTION:
Use only specified specification bulbs, do not use bulbs with different specifications to avoid
damaging electrical system, burning out bulbs, and discharging the battery.
Do not modify or add other electrical components to prevent over load or short circuit which may
result in a fire and burn down the motorcycle in serious cases.
INSTALLATION
Press in from above
REMOVE
Wire
Fuse connectors
20
§CHECKING FOR FUEL LEAKAGE§
Check fuel tank, fuel cup, fuel hose, and carburetor for leakage.
§CHECKING THE LUBRICATION OF BODY’S VARIOUS MECHANISMS§
Check the body
s pivot points if they have enough lubrication.
(for example, the pivot points on the main stand, the side stand, and the brake leveretc.).
§CHECKING THE SPARK PLUG§
Remove the cap of spark plug cable (remove the spark plug using
the spark plug wrench in the tool kit.
Check the electrode if it is dirty or fouled by carbon deposits.
Remove the carbon deposits on the electrode with steel wire, and
clean the spark plug with gasoline, then, wipe dry with a rag.
Check the electrode, and adjust its gap to 0.6~0.7 mm. (Check it
with a feeler gauge)
Hand tight the spark plug as far as it can go and then tighten it
another 1/2~3/4 turns with a wrench.
WARNING:
The engine is very hot after running. Pay attention not to get burned.
Use only spark plugs suitable for the engine specifications of this motorcycle recommended by the
manufacturer. (Refer to specifications.)
§CHECKING THE AIR CLEANER §
DISASSEMBLE PRCEDURE
1. Remove mounting screws from air cleaner cover.
2.Remove the air cleaner cover, then remove filter element.
3.Take the element out and clean it. (Refer to maintenance
schedule.)
DISASSEMBLE PRCEDURE
Assemble the air cleaner in reverse order of disassemble.
CAUTION:
Dust deposit is one of the major causes of reducing output horsepower and increasing fuel
consumption.
Change the air cleaner element more frequently to prolong the engine’s service life if the motorcycle
is driven on dusty roads very often.
If air cleaner is installed improperly, dust will be absorbed into cylinders, which may cause a
premature wear and reducing output power and engine life.
Be careful not to soak the air cleaner when washing the motorcycle. Otherwise, it will cause engine
hard to start.
0.6~0.7 mm
Screws
Element
21
11.WHEN THERE IS AN ABNORMAL CONDITION OR A TROUBLE
§DIAGNOSIS WHEN ENGINE DOES NOT START §
(1). Has the ignition switch key
been turned to the “ON”
position?
(2). Is there enough fuel in the fuel
tank?
(3). Is the rear or front wheel
brakes applied when
pressing starting button?
(4). Do you rotate the throttle valve handle while
pressing starting the button?
(5). Turn the ignition switch key to the “ON”
position, and press horn button down, if the
horn does not sound, the fuse may have been
blown.
Have your motorcycle checked by SYM authorized dealer immediately if there are no problems with the above
items and engine still can not be started.
12. C.D.I. ELECTRICL IGNITION SYSTEM
The charge and discharge principle of a condenser is adopted for the C.D.I system to supply electrical energy
created by generator’s coil, to the ignition coil in accordance with specified ignition timing so that the spark plug
may generate sparks as required.
13. SUGGESTIONS ON ENGINE FUEL
This motorcycle is designed to use UNLEADED gasoline of Octane No. 90 or higher.
If the motorcycle is operated in high attitude (where the atmosphere pressure is lower), it is suggested
that the air/fuel ratio should be readjusted to maximize the engine performance.
14. TRANSMISSION OIL
Recommended OIL: SAE 85W-140
For rear wheel
For front wheel
1/4
1/8
Turn Signal Switch
Horn Switch
22
15.CAUTIONS FOR RIDING MOTORCYCLE
1. Raise the motorcycle with the main stand, and sit on the seat.
Push the motorcycle forwarding to raise the main parking stand.
CAUTION:
Never rotate the throttle valve handle at will to increase the engine RPM before driving off.
2. Get on the motorcycle from the left side, and sit on the saddle properly, keep your right feet firmly on the
ground to prevent the motorcycle from falling.
CAUTION:
Apply brake on the rear wheel before driving off.
3. Rotate the throttle valve handle slowly, and then the motorcycle will begin to move.
CAUTION:
Rapidly rotate the throttle valve handle or release the clutch lever may cause the motorcycle moving
forward suddenly and it is very dangerous.
Make sure the side parking stand is spring back completely before driving off.
Do not use the brake suddenly and make a sharp turn
Rapid braking and sharp turning will cause slip and fall.
Rapid braking or sharp turning will cause slipping, lateral slipping, or fall especially in rainy days when
the road is wet and slippery.
Drive with extreme caution during rainy days
The brake distance in rain day or on wet road will longer than that on a dry road. Therefore, slow down
and prepare to apply the brake earlier.
The throttle valve handle should be released, and the brakes should be properly applied as it is needed
while reducing the speed when going down a slope.
23
16.PERIODICAL MAINTENANCE SCHEDULE
Item
Maintenance
kilometer
300KM
Every
1000KM
Every
3000KM
Every
6000KM
Every
12000KM
Remarks
Check Items
Maintenance
Interval
NEW 1 Month
3 Months
6 Months
1 Year
1 Air cleaner element (Remark) I C R(paper)
R(sponge)
2 Air cleaner I C
3 Oil filter (Screen) C C
4 Engine oil R I Replacement for every 3000KM
5 Tire, pressure I I
6 Battery I I
7 Spark plug I I R
8 Carburetor (idle speed) I I
9 Steering bearing and handles I I
10 Check transmission for leakage I I
11 Check crankcase for leakage I I
12 Transmission oil R Replacement for every 5000KM(5 Months)
13 Drive belt/roller I R
14 Fuel tank switch and lines I I
15 Throttle valve operation and cable
I I
16 Engine bolts and nuts I I
17 Cylinder head, cylinder, and piston I
18 Exhaust system/cleaning carbon I
19 Cam Chain/ignition time I I
20 Valve clearance I I
21 Shock absorbers I I
22 Front/rear suspension I I
23 Main/side stands I I/L
24 Crankcase Blow-by system(PCV) I I
25 Clutch disk I
26 Brake mechanism/brake lining (pad)
I I
27 Bolts/nuts for each components I I
The above maintenance schedule is established by taking the monthly 1000 kilometers as a reference
which ever comes first.
Code: I ~ Inspection, cleaning, and adjustment R ~ Replacement
C ~ Cleaning (replaced if necessary) L ~ Lubrication
Remark: 1.Clean or replace the air cleaner element more often when the motorcycle is operated on dusty roads
or in the Heavily- polluted environment.
2. Maintenance should be performed more often if the motorcycle is frequently operated in high speed
and after the motorcycle has accumulated a higher mileage.
Notes in the remarks are used to indicate the applicable models.
24
17.SPECIFICATION
Model
Item Specification
ORBIT II 125 (AE12W1-6)
Length 1905mm
Width 690mm
Height 1125mm
Wheel base 1310mm
Net Weight 99kg
Type
4- stroke single cylinders engine
Fuel UNLEADED (OCTANE 90 OR HIGHER)
Cooling type Air-cooled
Displacement 124.6 c.c.
Compression ratio 10.5±0.2 :1
Maximum HP 6.5kw/7500 rpm
Maximum torque 8.6N.m/7000 rpm
Starting methods Electrical & foot type
Front shock absorber TELESCOPE
Rear shock absorber UNIT SWING
Clutch Centrifugal type
Transmission CVT
Front tire 120/70-12
Rear tire 130/70-12
Wheel Aluminum
Tire pressure
Front: STD 2.00 kg/cm
2
,
Rear: STD 2.00kg/cm
2
for 1 person, 2.25kg/cm
2
for 2 persons
Front brake Disk type (Ø 190 mm)
Rear brake Drum type (Ø 130 mm)
Front light bulb (high, low) HS1 12V 35/35W
Brake light bulb (tail light) 12V 21W
License light bulb 12V 5W
Turn signal light bulb 12V 10W
Speedometer light bulb 12V 1.7W
Engine oil capacity 0.95 L (0.70 L for change)
Transmission oil capacity 180c.c (170c.c for change)
Fuel tank capacity 5.2L
Fuse 15A&10A
Spark plug A7RC
Battery capacity 12V 6Ah(closed type, maintenance-free battery)
Air cleaner Paper type
Fuel tank cap Close lock type
Rear grab frame Can not load cargo
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Sym-Orbit-II
6

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sym Orbit II bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sym Orbit II in de taal/talen: Engels als bijlage per email.

De handleiding is 2,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Sym Orbit II

Sym Orbit II Gebruiksaanwijzing - Nederlands - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info