11951

Sylvania 6719DD Handleiding

1
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
COLOR TV/DVD/VCR TRIPLE COMBO
6719DD
(19 inch)
6727DD
(27 inch)
OWNER’S
MANUAL
As an ENERGY STAR
Partner, our company has
determined that this product meets
the E
NERGY STAR guidelines for
energy efficiency. E
NERGY STAR is
a U.S. registered mark.
®
®
®
If you need additional operating assistance after reading this owner’s
manual or to order replacement accessories, please call
TOLL FREE : 1-800-968-3429.
Or visit our WEB SITE at http://www.funai-corp.com
Please read before using this equipment
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
This Owner’s Manual is
made of recycled paper.
SUPPLIED ACCESSORIES
Batteries
Remote Control Unit
ACCESSORIES
2 AA Batteries
NE209UD
PART NO.
27” MODEL ILLUSTRATED
Owner’s Manual 0EMN02116
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 1
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
5.Cleaning-Unplug TV/DVD/VCR from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possi-
bility of the loss of an authorization code for a CATV con-
verter, is not intended to be unplugged by the user for clean-
ing or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description other-
wise required in item 5.
6.Attachments-Do not use attachments not recommended by
the TV/DVD/VCR manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this TV/DVD/VCR near
water-for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
8.Accessories-Do not place this TV/DVD/VCR on an unstable
cart, stand, tripod, bracket, or table. The TV/DVD/VCR may
fall, causing serious injury to someone, and serious damage
to the appliance. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with the
TV/DVD/VCR. Any mounting of
the appliance should follow the
manufacturer’s instructions and
should use a mounting accessory
recommended by the manufacturer.
An appliance and cart combination
should be moved with care.Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
AMEUBLES- Cet appareil ne doit
être placé que sur un meuble (avec
ou sans roulettes) recommandé par
le fabricant. Si vous l’installez sur
un meuble à roulettes, déplacez les
deux ensembles avec précaution.
Un arrêt brusque, l’utilisation
d’une force excessive et des sur-
faces irrégulières risquent de désta-
biliser l’ensemble et de le renverser.
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the TV/DVD/VCR and to protect it from over-
heating, and these openings must not be blocked or cov-
ered. The openings should never be blocked by placing the
TV/DVD/VCR on a bed, sofa, rug, or other similar surface.
This TV/DVD/VCR should never be placed near or over a
radiator or heat register. This TV/DVD/VCR should not be
placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
10.Power Sources-This TV/DVD/VCR should be operated
only from the type of power source indicated on the mark-
ing label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For TV/DVD/VCRs intended to operate from
battery power, or other sources, refer to the operating
instructions.
11.Grounding or Polarization-This TV/DVD/VCR is
equipped with a polarized alternating-current line plug(a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety fea-
ture. If you are unable to insert the plug fully into the out-
let, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying par-
ticular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
- 2 - EN
1B15
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSON-
NEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DAN-
GEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
PORTABLE CART WARNING
S3126A
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 2
- 3 - EN
1B15
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/DVD/VCR, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV/DVD/VCR
receiver during a lightning storm, or when it is left unat-
tended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV/DVD/VCR due to
lightning and power-line surges.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/DVD/VCR through openings as they may
touch dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the TV/DVD/VCR.
18.Servicing-Do not attempt to service this TV/DVD/VCR
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19.Damage Requiring Service-Unplug this TV/DVD/VCR
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/DVD/VCR.
c. If the TV/DVD/VCR has been exposed to rain or water.
d. If the TV/DVD/VCR does not operate normally by follow-
ing the operating instructions. Adjust only those controls
that are covered by the operating instructions, as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the TV/DVD/VCR to its normal operation.
e. If the TV/DVD/VCR has been dropped or damaged in any
way.
f. When the TV/DVD/VCR exhibits a distinct change in per-
formance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
21.Safety Check-Upon completion of any service or repairs to
this TV/DVD/VCR, ask the service technician to perform
routine safety checks to determine that the TV/DVD/VCR
is in proper operating condition.
22.Heat-This TV/DVD/VCR product should be situated away
from heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce heat.
GROUND CL AMPS
NEC - NATIONAL ELECTRI CAL CODE
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
S2898A
WIRE
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRODE SYSTEM
(NEC ART 250, PART H)
SERVICE
EQUIPMENT
CLAMP
ANTENNA
LEAD IN
ANTENNA
POWER SERVICE GROUNDING
GROUND
ELECTRIC
FIGURE A
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 3
- 4 - EN
1B15
RADIO-TV INTERFERENCE
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public perfor-
mance and lending of discs are prohibited.
LASER SAFETY
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to ser-
vice this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUST-
MENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est con-
forme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
PRECAUTIONS
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 4
- 5 - EN
1C29
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
LOCATION
For safe operation and satisfactory performance of
your TV/DVD/VCR, keep the following in mind
when selecting a place for its installation:
•
Shield it from direct sunlight and keep it away from
sources of intense heat.
•
Avoid dusty or humid places.
•
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top and bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
•
Install unit in a horizontal position.
•
Avoid locations subject to strong vibration.
•
Do not place the TV/DVD/VCR near strong magnetic
fields.
•
Avoid moving TV/DVD/VCR to locations where
temperature differences are extreme.
•
Do not handle the power cord with wet hands.
•
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
•
If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
•
Do not put your fingers or objects into the
TV/DVD/VCR disc loading tray.
•
Do not place anything directly on top of the unit.
WARNING
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a TV/DVD/
VCR which has moisture, it may damage the DVD
and TV/DVD/VCR. Therefore when the condensation
occurs inside the unit, turn the POWER on and allow
at least 2 hours for the unit to dry out.
The serial number of this product may be found on the back of the unit. No other TV/DVD/VCR has the same
serial number as yours. You should record the number and other vital information here and retain this book as
a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-
tions concerning chemical wastes.
The following symbols below appear in some head-
ings and notes in this manual, with the following
meanings
: Description refers to TV/VCR operation (in the
TV/VCR mode).
: Description refers to playback of DVD video discs
(in the DVD mode).
: Description refers to playback of audio CDs
(in the DVD mode).
: Description refers to playback of MP3 discs
(in the DVD mode).
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
QUICK
MP3
CD
DVD-V
TV/VCR
SYMBOLS USED IN THIS MANUAL
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 5
- 6 - EN
1C29
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . .2, 3
C PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
SYMBOLS USED IN THIS
MANUAL . . . . . . . . . . . . . . . . . . . . .5
C TABLE OF CONTENTS . . . . . . . . . .6
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . .9, 10
C PREPARATION FOR USE . . . . . . .11
ANTENNA/CABLE
CONNECTION . . . . . . . . . . . . . . . .11
CONNECTING TO EXTERNAL
INPUT JACKS . . . . . . . . . . . . . . . .12
INSTALLING THE BATTERIES . .12
EXTERNAL INPUT MODE . . . . . .12
CONNECTING TO A STEREO
SYSTEM . . . . . . . . . . . . . . . . . . . .13
CONNECTING TO A STEREO
AMPLIFIER EQUIPPED WITH DIGI-
TAL INPUT JACKS SUCH AS MD
DECK OR DAT DECK (for DVD) .13
CONNECTING TO A DOLBY
DIGITAL DECODER
OR DTS DECODER (for DVD) . . .14
TV/VCR SECTION
C SET UP FOR USE . . . . . . . . . . . . .15
CHANNEL SET UP
FOR THE FIRST TIME . . . . . . . . .15
DELETING (OR ADDING)
CHANNEL . . . . . . . . . . . . . . . . . . .15
CHANNEL SET UP AGAIN . . . . . .16
SELECTING THE LANGUAGE . .16
DAYLIGHT-SAVING TIME . . . . . .16
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . .17, 18
C TV OPERATION . . . . . . . . . . . . . . .19
WATCHING A TV PROGRAM . . .19
DEGAUSSING . . . . . . . . . . . . . . . .19
PICTURE CONTROL . . . . . . . . . . .19
CLOSED CAPTION SYSTEM . . . .20
V-CHIP SET UP . . . . . . . . . . . . . . .21
C MTS(Multi-Channel Television
sound)SYSTEM . . . . . . . . . . . . . . . .23
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .23
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .23
SELECTING THE MTS SYSTEM .24
C VIDEO CASSETTE . . . . . . . . . . . . .25
C PLAYBACK . . . . . . . . . . . . . . . . . . .26
NORMAL PLAYBACK . . . . . . . . .26
TRACKING ADJUSTMENT . . . . .26
SLOW MOTION . . . . . . . . . . . . . .26
PICTURE SEARCH . . . . . . . . . . . .26
STILL PICTURE . . . . . . . . . . . . . .26
VERTICAL HOLD CONTROL . . .26
C SPECIAL PLAYBACK . . . . . . . . . .27
RENTAL PLAYBACK . . . . . . . . . .27
AUTO REPEAT PLAYBACK . . . . .27
C SEARCH . . . . . . . . . . . . . . . . . . . . .28
ZERO RETURN . . . . . . . . . . . . . . .28
TIME SEARCH . . . . . . . . . . . . . . .28
INDEX SEARCH . . . . . . . . . . . . . .29
C SPECIAL FEATURES . . . . . . . . . .29
REAL TIME TAPE COUNTER . . .29
AUTO REWIND-EJECT . . . . . . . .29
C RECORDING . . . . . . . . . . . . . . . . .30
NORMAL RECORDING . . . . . . . .30
SKIPPING UNWANTED SCENES
DURING
RECORDING . . . . . . . . . . . . . . . . .30
OTR (One Touch Recording) . . . . . .31
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .31
C TIMER . . . . . . . . . . . . . . . . . . . . . .32
AUTOMATIC
TIMER RECORDING . . . . . . . . . .32
TIMER PROGRAM EXTENSION .33
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . .34
AUTO RETURN . . . . . . . . . . . . . . .34
SLEEP TIMER . . . . . . . . . . . . . . . .34
C ON SCREEN DISPLAY . . . . . . . . .35
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .35
DVD SECTION
C ABOUT THE DISCS . . . . . . . . . . . .36
PLAYABLE DISCS . . . . . . . . . . . .36
DISC TYPES . . . . . . . . . . . . . . . . .36
C PLAYING A DISC . . . . . . . . . . . . . .37
BASIC PLAYBACK . . . . . . . . . . . .37
GENERAL FEATURES . . . . . . . . .37
DISC MENU . . . . . . . . . . . . . . . . .37
TITLE MENU . . . . . . . . . . . . . . . . .37
RESUME . . . . . . . . . . . . . . . . . . . .38
PAUSE . . . . . . . . . . . . . . . . . . . . . .38
STEP BY STEP PLAYBACK . . . . .38
FAST FORWARD/REVERSE
SEARCH . . . . . . . . . . . . . . . . . . . .38
SLOW FORWARD / SLOW
REVERSE . . . . . . . . . . . . . . . . . . . .38
ZOOM . . . . . . . . . . . . . . . . . . . . . .38
C SEARCH FUNCTION . . . . . . . . . . .39
TRACK SEARCH . . . . . . . . . . . . .39
TITLE / CHAPTER SEARCH . . . .39
TIME SEARCH . . . . . . . . . . . . . . .39
MARKER SETUP SCREEN . . . . . .39
C
SPECIAL PLAYBACK FUNCTION . . .40
REPEAT . . . . . . . . . . . . . . . . . . . . .40
PROGRAM . . . . . . . . . . . . . . . . . . .40
RANDOM PLAYBACK . . . . . . . . .40
C PLAYING A MP3 DISC . . . . . . . . . .41
MP3 PLAYBACK . . . . . . . . . . . . . .41
TRACK SELECTION . . . . . . . . . . .41
PROGRAM . . . . . . . . . . . . . . . . . . .41
RANDOM PLAYBACK . . . . . . . . .41
C CHANGING THE SETTINGS . . . .42
SUBTITLE LANGUAGE . . . . . . . .42
AUDIO LANGUAGE . . . . . . . . . . .42
STEREO SOUND MODE . . . . . . . .42
CAMERA ANGLE . . . . . . . . . . . . .42
BLACK LEVEL SETTING . . . . . . .42
VIRTUAL SURROUND . . . . . . . . .42
C
THE ON-SCREEN INFORMATION . . .43
C CHANGING THE DVD SETUP
ITEMS . . . . . . . . . . . . . . . . . . . . . . .44
LANGUAGE SETTING . . . . . . . . .44
DISPLAY SETTING . . . . . . . . . . . .45
AUDIO SETTINGS . . . . . . . . . . . .45
PARENTAL CONTROL . . . . . . . . .46
C TROUBLESHOOTING GUIDE . . .47
C MAINTENANCE . . . . . . . . . . . . . . .50
DISC HANDLING . . . . . . . . . . . . .50
C SPECIFICATIONS . . . . . . . . . . . . .51
C WARRANTY . . . . . . . . . . .Back Cover
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 6
- 7 - EN
1C29
•
Hi-Fi system
–The Hi-Fi stereo recording system
offers you excellent sound quality with a dynamic
range of 80dB, frequency response from 20Hz to
20kHz, and 0.005% wow and flutter.
•
Rotary 4-head Record/Playback System–Four heads
ensure excellent picture quality and special effects playback.
•
Index Search–
Fast-forwards to start of next recording.
•
Slow Motion–View recorded program at slower
than normal speed.
•
Infrared remote control
•
Trilingual on screen tv/vcr setup display selec-
table in English or Spanish or French
•
Real time counter–This shows the elapsed recording
or playback time in hours, minutes, and seconds.
The
“–” indication will appear when the tape is rewound
further than the tape counter position “0:00:00”.
•
181 channel capability PLL frequency synthesiz-
er tuner with direct station call–
(A converter may
be necessary to view scrambled cable channels.)
•
Auto Clock Setting–Allows you to set the clock
function from a PBS broadcast station.
•
Closed caption system–You may view specially
labeled (cc) TV programs, movies, news, prere-
corded tapes, etc. with either a dialogue caption or
text display added to the program.
•
Auto power on and off system–Automatically
turns on the TV/DVD/VCR when you insert the
cassette, turns off after auto-rewind, and ejects
when the beginning of the tape is reached.
•
Auto rewind when the end of a tape is
reached–
This function doesn’t occur when using
timer recording.
•
Smooth mode change–TV/VCR mode, DVD
mode automatically changes without control.
•
2 Step picture search operation–You can view a
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
•
Three different playback tape speeds : SP/LP/SLP
•
Two different recording tape speeds : SP/SLP
•
Auto Head Cleaner–Automatically cleans video
heads as you insert or remove a cassette.
•
Zero Return–The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
•
Still–“Freeze” the picture at any time, for close
viewing of a particular scene.
•
Digital Auto Tracking (DTR)–Automatically
adjusts the tracking for each tape you play.
•
Rental play mode–Improves playback picture
quality from worn tapes, such as rental tapes.
•
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
•
Time search–Let you set the TV/DVD/VCR to
advance the tape by entering the desired playback
time you want to skip.
•
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible at the
push of the REC/OTR button.
•
1 Year, 8 events (including Daily and Weekly
Timer Recording)–
The built-in timer allows you to
record up to 8 programs at different times on dif-
ferent channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broad-
casts, and the Weekly timer allows recording to be
made once a week up to the end of the tape.
•
Auto return–After timer recording is finished, the
TV/DVD/VCR can return to the beginning of the
recording.
•
Sleep timer–Allows you to have the
TV/DVD/VCR
automatically turn on or off at a desired time.
Timer Program Extension–Allow you to shift the
time schedule for automatic timer recording.
•
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
FEATURES
TV/VCR Mode
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-
tions concerning chemical wastes.
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 7
- 8 - EN
1C29
¡Dolby Digital sound
This player can handle Dolby Digital surround
sound having 5.1 channels when connected to a
Dolby Digital decoder.
¡Still/fast/slow/step playback
Various playback modes are available including still
pictures, fast forward/reverse, slow motion and step
frames.
¡Random playback for audio CD and MP3
This player can shuffle the order of tracks to play
them in random order.
¡Program playback for audio CD and MP3
You can program the order of tracks to play them in
any desired order.
¡DVD menus in a desired language
You can display DVD menus in a desired language,
if available on a DVD.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no
input from the player for five minutes in the stop
mode. When the screen saver program is activated
for 15 minutes, the power automatically turns off.
¡Subtitles in a desired language
You can select a desired language for the display
subtitles, if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc
contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available
on a disc.
¡Parental lock
You can set the control level to limit playback of
discs which may not be suitable for children.
¡Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡Playback MP3 disc
¡On-screen display
Information about the current operation can be dis-
played on a TV screen, allowing you to confirm the
currently active functions (such as program play-
back), on the TV screen using the remote control.
¡Search
Chapter search / Title search / Track search / Time
search
¡Repeat
Chapter / Title / Track / Group / All / A-B
¡Zoom
Magnified screen can be displayed.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which
the play was stopped.
¡Virtual Surround
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
NOTE:
•
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
If you decide to use a universal remote control with this TV/VCR/DVD, please be aware that the code num-
ber given may not operate this TV/VCR/DVD. In this case, please call the manufacturer of the universal
remote control.
DVD Mode
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 8
- 9 - EN
1C29
OPERATING CONTROLS AND FUNCTIONS
5.STOP Button
[P.37]
Stops operation of the disc.
6.OPEN/CLOSE Button
[DVD P.37]
Press to insert discs into or remove them from the
tray.
7.Disc loading tray
8.DVD Indicator
Lights on during DVD mode.
9.SELECT Button
Press to change to TV/VCR mode, external input
mode or DVD mode.
10.TV/VCR Indicator
Lights on during TV/VCR mode.
11. CHANNEL K/L Buttons
Press to select memorized channel.
12. Recording Indicator
Flashes during recording. Lights up in the Stand-
by mode for Timer Recording.
13. REC/OTR (RECORD)Button
[TV/VCR P.30, 31]
Press for manual recording. Activates One Touch
Recording. (OTR is only during TV/VCR mode.)
14. REW Button (for TV/VCR)
[TV/VCR P.26]
Press to rewind the tape, or to view the picture
rapidly in reverse during playback mode. (Rewind
Search)
15. FWD Button (for TV/VCR)
[TV/VCR P.26]
Press to rapidly advance the tape, or to view the
picture rapidly in forward during playback mode.
(Forward Search)
16. STOP/EJECT Button
[TV/VCR P.28]
Press to stop the tape motion. Press in the Stop
mode to remove tape from the TV/VCR/DVD.
17. Remote sensor window
18. HEADPHONE Jack
To connect headphone (not supplied) for personal
listening.
19. VIDEO input Jack
Connect to the video output jack of a video
camera or VCR.
- REMOTE CONTROL -
[Fig. 2]
1.POWER Button
[TV/VCR P.15 / DVD P.37]
Press to turn the power on and off.
2.VOLUME X/Y Buttons
Press to control the volume level for the DVD and TV.
3.SKIP Buttons (for DVD)
[P.38]
Press once to skip chapters or tracks to a desired
point.
Press and hold to change forward or reverse play-
back speed.
4.PLAY Button
[TV/VCR P.26 / DVD P.37]
Starts playback of the disc or tape contents.
- TV/DVD/VCR FRONT PANEL - [Fig.1]
OPEN/CLOSE
SELECT
CHANNEL
REC/OTR
TV/VCR
DVD
STOP
SKIP
PLAY
SKIP
VOLUME
POWER
SEARCH
RL
AUDIO
VIDEO
HEADPHONE
STOP/EJECT
F.FWD
PLAY
REW
12 4 5 6 107 1514983 3 411 12 13 212019181716
DVD buttons TV/VCR buttons
PAUSE
PLAY
STOP
ENTER
RECORD
DISC
MENU
RETURNTITLESETUP
A
-
B
REPEATSEARCH MODE
CLEAR
MODE
ANGLESUBTITLEAUDIO
DISPLAY
SPEED C.RESET
POWER PICTURE SELECTSLEEP
CH.
VOL.
MUTEZOOM
123
456
789
0 +10
+100
34
35
23
24
26
25
(DVD) 3
(TV/VCR) 14
13
27
28
30
31
33
32
29
4
36
37
38
41
3 (DVD)
15 (TV/VCR)
43
2
11
45
44
42
5
39
40
1
22
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 9
- 10 - EN
1C29
ANT.
L
AUDIO OUT
R
COAXIAL
1
4746 48 49
20. AUDIO L/R input Jacks
Connect to the audio output jacks of a video
camera or VCR.
21. Cassette compartment
22. PICTURE Button
Press to adjust the picture.
23. Number Buttons
TV Mode:
[P.15]
Press two digits to directly access the desired
channel.
Remember to press a "0" before a single digit
channel.
+100 Button–
Press to select cable channels which are equal or
greater than number 100.
DVD Mode:
Press to enter the desired number.
+10 Button–
Press to enter the desired numbers which are
equal or greater than number 10.
24. PAUSE Button
[TV/VCR P.26 / DVD P.38]
Pauses the current disc or tape operation.
25. SPEED Button
[TV/VCR P.30]
Press to choose the desired recording speed:
SP/SLP.
26. C.RESET Button
[TV/VCR P.28]
Press to reset counter to 0:00:00.
Press to cancel a setting of timer program. (See
page 33.)
27. DISPLAY Button
TV/VCR Mode:
Display the counter or the current channel number
and current time on the TV screen.
DVD Mode:
[P.43]
Displays the current status on the TV screen for
checking purposes.
28. SETUP Button
[TV/VCR P.15] [DVD P.44-46]
Press to enter or exit the TV menu or DVD setup
mode.
29. TITLE Button
[DVD P.37]
Displays the title menu.
30. CLEAR Button
Resets a setting.
31. MODE Button
[DVD P.41]
Activates program playback or random playback mode.
32. SEARCH MODE Button
[DVD P.39]
Press to locate a desired point.
33. AUDIO Button
[DVD P.42]
Press to select a desired audio language or sound
mode.
34. SUBTITLE Button
[DVD P.42]
Press to select a desired subtitle language.
35. REPEAT Button
[DVD P.42]
Repeats playback of the current disc, title, chapter
or track.
36. ANGLE Button (DVD mode)
[DVD P.42]
Press to change the camera angle to see the
sequence being played back from a different angle.
37. A-B REPEAT Button
[DVD P.40]
Repeats playback of a selected section.
38. RETURN Button
Returns to the previous operation in the DVD
setup mode.
39. ENTER Button
Press to accept a setting.
40. Arrow Buttons
TV/VCR Mode:
Press to select a setting mode from the menu on
the TV screen.
Press to select or adjust from a particular menu.
DVD Mode:
Use when making settings while watching the
display on a TV screen.
41. DISC MENU Button
[DVD P.37]
Displays the menus in the DVD.
42. ZOOM Button
[DVD P.38]
Enlarges part of a DVD-reproduced image.
43. MUTE Button
Mutes the sound. Press it again to resume sound.
44. SLEEP Button
[TV/VCR P.34]
Sets the Sleep Timer.
45. SELECT Button
Press to switch TV/VCR and DVD mode. You can
see the mode (TV/VCR or DVD) on the front
panel indicator.
- TV/DVD/VCR REAR PANEL - [Fig.3]
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 10
- 11 - EN
1C29
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown in the illustration.
By using this connection you can also record scram-
bled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/DVD/VCR Remote Control. Unattended timer
recording is limited to one channel at a time.
PREPARATION FOR USE
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to your TV/DVD/VCR without a converter
box.
By using this connection you can:
1) Use the TV/DVD/VCR remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE: This TV/VCR/DVD will ONLY record and
view the same channel.
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor
antenna.
Antenna/Cable Connections
Continued on the Next Page.
ANT.
L
AUDIO OUT
R
COAXIAL
1
ANT.
IN
OUT
or
VHF/UHF Antenna
(Not supplied)
VHF/UHF
Combiner
(Not supplied)
Flat twin-lead cable
UHF Antenna
(Not supplied)
VHF Antenna (Not supplied)
From Cable
System
75-ohm Coaxial
Cable (Not
supplied)
75-ohm
Coaxial
Cable
(Not sup-
plied)
Satellite Box or
Cable Box (Not supplied)
From Cable System or
Satellite Dish
46. ANT. in Jack
Connect to an antenna, cable system, or satellite
system.
47. Power cord
Connect to a standard AC outlet (120V/60Hz).
NOTE: Remove the power cord from the hook to
avoid breaking a wire before you connect
to a standard AC outlet.
48. COAXIAL digital audio out Jack
Connect to the digital input of an external
amplifier or decoder for DVD audio only.
49. AUDIO L/R output Jack
Connect to the analog audio input of an external
amplifier or decoder.
[Fig. 4]
ANTENNA/CABLE CONNECTION
or
or
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 11
- 12 - EN
1C29
TO RECORD A SCRAMBLED/UNSCRAM-
BLED CHANNEL
1. Set the TV/DVD/VCR channel selector to the out-
put channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
EXTERNAL INPUT MODE
When using an external input signal (another VCR or
video camera), connect the player’s audio/video out-
put cables to the AUDIO L/R IN/
VIDEO IN jacks of your
TV/DVD/VCR. Then press the
CHANNEL button K or L until
“AUX” appears on the screen.
AUX
Note to CATV system installer:
This reminder is provided to call the CATV sys-
tem installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper ground-
ing and, in particular, specifies that the cable
ground shall be connected to the grounding sys-
tem of the building as close to the point of cable
entry as practical.
CONNECTING TO EXTERNAL
INPUT JACKS
When you watch a program recorded on an another
source (VCR or video camera), use the audio/video
input jacks on the front of the TV/DVD/VCR.
Connect the audio/video output jacks of another
source to the AUDIO L/R and VIDEO jacks of this
TV/DVD/VCR.
Then press the CHANNEL buttons K/L until "AUX"
appears on the screen.
NOTE:
•
When you connect a monaural VCR (another
source) to this TV/DVD/VCR, connect the Audio
output jack of the monaural VCR (another source)
to the AUDIO L jack of this TV/DVD/VCR. The
audio will output in both L and R channel equally.
[Another source]
To the audio
output jacks
Audio/Video
coaxial cable
(not supplied)
etc.
To the video
output jack
[Front of the
TV/DVD/VCR]
[Fig. 5]
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 12
- 13 - EN
1C29
CONNECTING TO A STEREO SYSTEM
ANT.
L
AUDIO OUT
R
COAXIAL
1
To Right (red) and Left (white)
AUDIO OUT jacks
Stereo system
To ANALOG AUDIO INPUT jacks
NOTES:
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for your stereo system and any other components to be connected to the
TV/DVD/VCR.
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGI-
TAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)
Use an audio coaxial digital cable available at retail for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
NOTES:
•
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR.
•
Set Dolby Digital to OFF for audio output in the setup mode. Playing a TV/DVD/VCR using incorrect set-
tings may generate noise distortion, and may also damage the speakers.
ANT.
L
AUDIO OUT
R
COAXIAL
1
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
To COAXIAL DIGITAL
AUDIO INPUT jack
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
(only DVD AUDIO OUT)
[Fig. 6]
[Fig. 7]
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 13
- 14 - EN
1C29
ANT.
L
AUDIO OUT
R
COAXIAL
1
Front speaker
(left)
Center
speaker
Front speaker
(right)
Surround
speaker
(left)
Surround
speaker
(right)
Subwoofer
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
To COAXIAL DIGITAL
AUDIO INPUT jack
Dolby Digital
decoder
[Fig. 8]
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this TV/DVD/VCR to play a DVD disc in a 5.1 channel Dolby Digital surround format, the
TV/DVD/VCR outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hook-
ing the player up to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with pow-
erful and high-quality surround sound as enjoyed in movie theaters.
Use audio coaxial digital cables available at retail for the audio connections.
NOTES:
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR.
•
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.
(See page 45 to set DOLBY DIGITAL to ON.)
•
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup
mode. Playing a TV/DVD/VCR using incorrect settings may generate noise distortion, and may also dam-
age the speakers.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 14
- 15 - EN
1C29
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/DVD/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3).
Then select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
1 Plug in the TV/DVD/VCR power
cord
Plug the TV/DVD/VCR power cord
into a standard AC outlet.
NOTE:
•
If some digits appear in the corner of
the screen, press the POWER button without
unplugging the power cord.
2 Turn on the TV/DVD/VCR
Press the POWER button to turn on the TV/DVD/VCR.
3 Select “ENGLISH” or “ESPAÑOL” or
“FRANÇAIS”
Select “ENGLISH” or
“ESPAÑOL”=Spanish or
“FRANÇAIS” =French using the
ENTER button. “[ ]” indicate the
selected language.
4 Begin auto preset
Press the Arrow button K or L to
point to “AUTO PRESET”.
Then press the ENTER button.
The tuner scans and memorizes all
active channels in your area.
NOTES:
•
The TV/DVD/VCR distinguishes between standard
TV channels and cable channels.
•
If you want to play or record a video tape
BEFORE presetting the tuner, you must press the
SETUP button on the remote control. To preset the
tuner again, see “CHANNEL SET UP AGAIN” on
page 16.
•
The TV/DVD/VCR may memorize TV channels as
CATV channels if reception conditions is poor. If
this happens, try AUTO MEMO action again when
reception conditions are better.
5 After scanning
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can
select the desired channel directly with the remote con-
trol number buttons or the CHANNEL button K or L.
TV/VCR
DELETING (OR ADDING)
CHANNEL
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
1 Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CHANNEL SET UP”.
Then, press the ENTER button.
2 Select “ADD/DELETE CH”
Press the Arrow button K or L to
point to “ADD/DELETE CH”.
Press the ENTER button.
3 Enter the desired channel number
Press the Arrow button K or L until
your desired channel number appears.
(You can also use the number buttons
or the CHANNEL buttons K/L to
enter it) (Example: CH8)
4 Delete (or add) it from (into) memory
Press the ENTER button. The channel number changes
to light red. The channel is deleted from memory.
•
To delete another channel, repeat steps [3] and [4].
•
If you press the ENTER button again, the channel
is memorized again.
•
Press the RETURN button to return to TV/VCR
SETUP MENU.
5 Exit the channel setup mode
Press the SETUP button on the remote control to
returns to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL button K or L.
TV/VCR
Added channel: Light blue.
Deleted channel: Light red.
– SET UP –
B LANGUAGE
[ENGLISH] ESP FRA
AUTO PRESET
– SET UP –
LANGUAGE
[ENGLISH] ESP FRA
B AUTO PRESET
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (TV)
AUTO PRESET
08
ADD / DELETE
TV/VCR SECTION
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 15
- 16 - EN
1C29
CHANNEL SET UP AGAIN
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VCR.
1 Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CHANNEL SET UP”.
Then, press the ENTER button.
2 Begin auto preset
Press the Arrow button K or L to
point to “AUTO PRESET”.
Then, press the ENTER button.
The tuner scans and memorizes all
the active channels in your area.
3 After scanning
The tuner stops on the lowest memorized channel.
TV/VCR
SELECTING THE LANGUAGE
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VCR.
NOTE: This function effects only the language on
the screen menu and not the audio source.
1 Select “LANGUAGE”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “LANGUAGE”.
2 Select “ENGLISH” or “ESPAÑOL” or
“FRANÇAIS”
Select “ENGLISH” or “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using the ENTER button.
3 Exit the Language mode
Press the SETUP button on the remote control to
return to TV mode.
TV/VCR
NOTE: If Spanish or French is selected accidentally,
1)Press the SETUP button on the remote control.
2) Press the Arrow button K or L to point to “IDIOMA
[ESPAÑOL]” or “LANGAGE” [FRANÇAIS].
3)Press the ENTER button to select your desired lan-
guage.
4)Press the SETUP button to exit.
DAYLIGHT-SAVING TIME
Select this feature and the TV/DVD/VCR’s clock
automatically will advance one hour in April, then
reverse one hour in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
•
First Sunday of April : At 2 AM the clock imme-
diately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
•
Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VCR.
1 Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “SETTING CLOCK.”
Then, press the ENTER button.
2 Set “D.S.T.” (Daylight-Saving
Time) to [ON]
Press the Arrow button K or L to
point to “D.S.T.”
Then, press the ENTER button until
[ON] appears.
3 Exit the Daylight-Saving Time mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the
ENTER button.
TV/VCR
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
ADD / DELETE CH (TV)
B AUTO PRESET
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH [02]
MANUAL CLOCK SET
B D.S.T. [ON]
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 16
- 17 - EN
1C29
CLOCK SET UP
(AUTO / MANUAL)
The TV/DVD/VCR clock must be set correctly before
VCR timer recording is possible. It is suggested that the
clock be set manually when first setting up the
TV/DVD/VCR. Then, setup auto clock correction which
will periodically correct the setting if necessary.
NOTE: If you cannot receive a station with time sig-
nals, auto clock setting cannot be performed. Use
manual setting only.
MANUAL CLOCK SETTING
Make sure ...
•
TV/DVD/VCR power is turned on.
In the example below, the clock is to be set to:
DATE May 6th, 2003
SETTING TIME 5:40PM
TV/VCR
1 Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “SETTING CLOCK”.
Then, press the ENTER button.
2 Select “MANUAL CLOCK
SET”
Press the Arrow button K or L to
point to “MANUAL CLOCK SET”.
Then, press the ENTER button.
3 Select the month
Press the Arrow button K or L until
your desired month appears.
(Example: May
→ 05)
Then, press the Arrow button
B.
4 Select the day
Press the Arrow button K or L until
your desired day appears.
(Example: 6th → 06)
Then, press the Arrow button B.
5 Select the year
Press the Arrow button K or L until
your desired year appears.
(Example: 2003)
Then, press the Arrow button B.
6 Select the hour
Press the Arrow button K or L until
your desired hour appears.
(Example: 5, PM)
Then, press the Arrow button B.
7 Select the minute
Press the Arrow button K or L until
the desired minute appears.
(Example: 40)
8 Start the clock
Press the SETUP button on the
remote control.
Although seconds are not displayed,
they begin counting from 00 when
you press the SETUP button on the
remote control. Use this feature to synchronize the
clock with the correct time.
NOTE:
When unplugging the AC cord or if there is a power
failure for more than 3 seconds, you may have to
reset the clock.
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the Arrow
button B or s.
3)Enter correct numbers using the Arrow button K or
L.
4)Press the SETUP button on the remote control to
start the clock.
PLEASE NOTE:
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and
press the ENTER button to turn [OFF] this function.
Then you can manually adjust the clock.
– SETTING CLOCK –
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH [02]
B MANUAL CLOCK SET
D.S.T. [OFF]
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / – – – – –– – – –
HOUR MINUTE
– – : – –– –
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 6 – – –– – – –
HOUR MINUTE
– – : – –– –
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 6 TUE 2 0 0 3
HOUR MINUTE
– – : – –– –
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 6 TUE 2 0 0 3
HOUR MINUTE
0 5 : – – PM
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 6 TUE 2 0 0 3
HOUR MINUTE
0 5 : 4 0 PM
5:40 PM
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 17
- 18 - EN
1C29
AUTOMATIC CLOCK SETTING
Make sure ...
•
The TV/DVD/VCR is turned on.
•
Confirm the TV/DVD/VCR is receiving a RF
(Radio Frequency) signal from either an antenna or
cable system connection using the ANT IN jack on
the rear of the TV/DVD/VCR.
NOTE:
•
If a cable converter box is being used, make sure it
is powered on.
•
You must use the TV/DVD/VCR remote control to
perform the clock setting procedure.
1 Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
2 Set “AUTO CLOCK” to [ON]
Press the ENTER button until
AUTO CLOCK [ON] appears.
3 Begin “AUTO CLOCK CH SEARCH”
Press the Arrow button L to select “AUTO CLOCK
CH SEARCH”.
Press the ENTER button.
•
The TV/DVD/VCR is now
searching for the station which
contain the auto clock set signal.
The search for a signal may take
up to 20 seconds per channel.
•
“_ _” appears at the lower left of
the screen when the search has
ended.
•
Auto Clock station- write down
the number(s) that appear on the
screen. These are the auto clock
station(s) in your area. See item
4 below.
•
If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 17.
Press the SETUP button to exit the screen.
NOTE: During Auto Clock CH Search, the picture
may be distorted. This is normal.
4 Enter the channel number that contains the
Automatic Clock Setting Signal
Press the SETUP button on the remote control.
Press the Arrow button K or L to
select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
Press the Arrow button L to select
“AUTO CLOCK CH”.
Press the ENTER button, then
press the Arrow button B or s
until you locate Auto Clock Set
station number. See item 3 above.
Press the SETUP button to exit the
screen.
5 Turn off the TV/DVD/VCR
Once the TV/DVD/VCR is turned off , it will period-
ically check and set the correct date and time.
– SETTING CLOCK –
B AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH [02]
MANUAL CLOCK SET
D.S.T. [OFF]
– SETTING CLOCK –
AUTO CLOCK [ON]
B AUTO CLOCK CH SEARCH
AUTO CLOCK CH [02]
MANUAL CLOCK SET
D.S.T. [OFF]
– AUTO CLOCK CH SEARCH –
08 10 13
_ _
– SETTING CLOCK –
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH [ 45]
MANUAL CLOCK SET
D.S.T. [OFF]
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 18
- 19 - EN
1C29
TV OPERATION
DEGAUSSING
Magnetism from nearby appliances and speakers
might affect the color of the TV picture.
If this happens, move this TV/VCR/DVD away from
the appliance. If the color is still not correct, turn off
using the POWER button, then turn it on again 30
minutes or so later (27” model), or unplug the power
cord, then plug it in again 30 minutes or so later (19”
model).
TV/VCR
WATCHING A TV PROGRAM
1 Turn on the TV/DVD/VCR
Press the POWER button to turn on the
TV/DVD/VCR.
2 Select the channel number
Press the CHANNEL button K or L to select your
desired channel number or press the number on the
remote control.
Note for using the Number button on the remote
control:
¡When selecting cable channels which are higher
than 99, press +100 first, then, press the last two
digits. (Example: to select channel 125, first press
“+100” then press “2” and “5”).
¡You must precede single-digit channel numbers
with a zero (For example: 02, 03, 04 and so on).
Remember: If the TV/DVD/VCR is connected to a
cable box or satellite box, the TV/DVD/VCR must
be on CH3 or CH4, then the channel to be viewed
must be selected on the cable box or satellite box.
3 Adjust sound
Press the VOLUME button
XX
or
YY
to adjust the volume.
NOTES:
•
If you press the CHANNEL button o or p in the
DVD mode, you can change the TV channels.
Even if you turn off the TV/DVD/VCR in the
DVD mode, when you turn it on again, it will go
into the TV/VCR mode.
TV/VCR
Arrow button s Arrow button B
BRIGHT to decrease to increase
brightness brightness
CONTRAST to decrease to increase
contrast contrast
COLOR to pale to brilliant
TINT to purple to green
SHARPNESS to soft to clear
PICTURE CONTROL
The TV/DVD/VCR’s picture controls – BRIGHT,
CONTRAST, COLOR, TINT and SHARPNESS –
are preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a natural looking image.
NOTES:
•
Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
•
When setting the Picture Control, the Game mode
will be cancelled.
Make sure ...
•
TV/DVD/VCR power must be turned on.
1 Select “PICTURE CONTROL”
Press the PICTURE button on the remote control.
2 Select item you want to adjust
Press the Arrow button K or L until desired control
is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
3 Adjust the picture control
Press the Arrow button B or s to adjust to your
desired level.
TV/VCR
•
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this fea-
ture.
VOLUME 20
C C C C C C C C C C C C
BRIGHT
–
PP PP PP PP PP PP PP CC PP PP PP PP PP PP PP
+
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 19
- 20 - EN
1C29
CLOSED CAPTION SYSTEM
You can view specially labeled (cc) TV programs,
movies, news, pre-recorded tapes with either a dia-
logue caption or text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used,
usually for a second language if available.
NOTE:
Not all programs are broadcast with closed captions.
Your television is designed to provide error free
closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are
likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions
errors are listed below:
•
Automobile ignition noise
•
Electric motor brush noise
•
Weak snowy reception on TV screen
•
Multiplex signal reception displaying picture
ghosts or airplane flutter.
•
Playback of poorly recorded or worn VCR tapes.
NOTE:
If the TV/DVD/VCR displays a
black box on the TV screen, this
means that the TV/DVD/VCR is
set to the TEXT mode. To clear
screen, select [CAPTION1], [CAP-
TION2] or [OFF].
Make sure ...
•
TV/DVD/VCR power must be turned on.
TV/VCR
1 Select “CAPTION”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CAPTION”.
2 Select your desired caption menu
Press the ENTER button until your
desired caption menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
3 Exit the caption setting mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] and [2], select [OFF] using the
ENTER button. Press the SETUP button on the
remote control to return to TV mode.
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 sec-
onds.
•
It will also disappear when the MUTE button is
pressed, and when the PAUSE button is pressed
while recording.
•
If there is a power failure of any kind, the
TV/DVD/VCR will retain its memory for this fea-
ture.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [CAPTION1]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 20
- 21 - EN
1C29
5 Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
V-CHIP SET UP
Make sure ...
•
TV/DVD/VCR is turned on.
1 Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”.
Then, press the ENTER button.
2 Enter Access code
Use the number buttons on the remote
control to enter the access code.
•
For the first time set-up or in the
event the TV/DVD/VCR has lost
power, enter the default code of the numbers:
0000.
3 Select “TV RATING”
Press the Arrow button K or L to
select “TV RATING”.
Then, press the ENTER button.
4 Blocking TV programs
Press the Arrow button K or L to
select “TV rating” that you wish to
block.
Press the ENTER button to turn it
[BLOCK].
•
When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
•
When you turn “TV-Y” to [VIEW], then all ratings
will turn to [VIEW] automatically.
TV/VCR
ACCESS CODE
_ _ _ _
V-CHIP SET UP
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– V-CHIP SET UP –
B TV RATING
MPAA RATING
CHANGE CODE
B TV–Y [VIEW]
TV–Y7 ( ) [VIEW]
TV–G [VIEW]
TV–PG ( ) [VIEW]
TV–14 ( ) [VIEW]
TV–MA ( ) [VIEW]
Selection Rating Category Explanations
TV-Y Appropriate for all children
TV-Y7 Appropriate for children seven and older
TV-G General Audience
TV-PG Parental Guidance suggested.
TV-14 Unsuitable for children under 14
TV-MA Mature audience only
V-CHIP SET UP SUB RATINGS
When you select the ratings of TV-Y7,TV-PG,TV-14
or TV-MA you will have the option of selecting sub
rating categories.
1 Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”. Then,
press the ENTER button.
2 Enter Access code
Use the number buttons on the
remote control to enter the access
code. (Default code is 0000.)
3 Select “TV RATING”
Press the Arrow button K or L to
select “TV RATING”.
Then, press the ENTER button.
4 Selecting Sub-Ratings”
Press the Arrow button L to select the sub-rating you
wish to block. Then, press the ENTER button twice.
•
When you select [TV-Y7]:
Press the Arrow button L or K to
select “FV” (Fantasy Violence).
Then, press the ENTER button to
select [BLOCK] or [VIEW].
•
When you select [TV-PG], [TV-
14] or [TV-MA]:
Press the Arrow button L or K to
select “D”(Suggestive Dialog),
“L”(Coarse Language),
“S”(Sexual Situation), or
“V”(Violence). Then, press the
ENTER button to select [BLOCK] or [VIEW].
Note: When you select [TV-MA], “D” does not
appear on the TV screen.
•
The sub-ratings which set to
[BLOCK] appears next to the rat-
ing category in the TV rating
menu.
5 Exit the V-Chip setting mode
Press the SETUP button on the remote control to
enter the setting and exit the screen.
– V-CHIP SET UP –
B TV RATING
MPAA RATING
CHANGE CODE
TV–Y7 [BLOCK]
B FV [BLOCK]
TV–PG [BLOCK]
B D [BLOCK]
L [BLOCK]
S [BLOCK]
V [BLOCK]
B TV–Y [VIEW]
TV–Y7 ( ) [VIEW]
TV–G [VIEW]
TV–PG (DLSV ) [BLOCK]
TV–14 (DLSV) [BLOCK]
TV–MA ( LSV ) [BLOCK]
ACCESS CODE
_ _ _ _
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 21
- 22 - EN
1C29
CHANGING V-CHIP BLOCKED PRO-
GRAMMING
Note: To change the rating, the TV must be turned to
a station that is not protected. If the (PROTECTED)
appears on the screen, please change the channel to a
station that is not protected.
1)Follow steps [1] and [2].
2)Press the Arrow button K or L to select "TV RAT-
ING". Then, press the ENTER button. Select a TV
rating to be unblocked by pressing the Arrow but-
ton K or L.
Then press the ENTER button to unblock the rating.
3)Press the SETUP button on the remote control to
exit the screen.
MPAA RATING SET UP
1 Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”. Then,
press the ENTER button.
2 Enter Access code
Use the number buttons on the
remote control to enter the access
code.
3 Select “MPAA RATING”
Press the Arrow button K or L to
point to “MPAA RATING”.
Then, press the ENTER button.
4 Select your desired item
Press the Arrow button K or L to
point to your desired item.
Then, press the ENTER button to
select [BLOCK] or [VIEW].
•
When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
•
When you turn “G” to [VIEW], then all ratings
will turn to [VIEW] automatically.
Selection Rating Category Explanations
G General Audience
PG Parental Guidance suggested.
PG-13 Unsuitable for children under 13
R Restricted; under 17 requires accompa-
nying parent or adult guardian
NC-17 No one under 17 admitted
X Mature audience only
– V-CHIP SET UP –
TV RATING
B MPAA RATING
CHANGE CODE
G [VIEW]
PG [VIEW]
PG–13 [VIEW]
B R [BLOCK]
NC–17 [BLOCK]
X [BLOCK]
ACCESS CODE
_ _ _ _
5 Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
CHANGE ACCESS CODE
To change access code, follow the steps.
1 Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “V-CHIP
SET UP”.
Then, press the ENTER button.
2 Enter Access code
Use the number buttons on the remote
control to enter the access code.
The default code is 0000.
3 Select “CHANGE CODE”
Press the Arrow button K or L to
select "CHANGE CODE". Then,
press the ENTER button.
4 Enter New code
Use the number buttons to enter
your desired access code in the
NEW CODE space. Then enter the
same code in the CONFIRM
CODE space. V-CHIP SET UP
screen appear on the screen.
•
If you enter wrong code, repeat step 4, making
sure you enter the same new code exactly in the
confirm code space.
5 Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
Note: If you unplug the power code or power failure
occurs, the changed access code will be lost and will
return to default (0000). Change your access code
again as necessary.
ACCESS CODE
_ _ _ _
NEW CODE
X X X X
CONFIRM CODE
_ _ _ _
– V-CHIP SET UP –
TV RATING
MPAA RATING
B CHANGE CODE
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 22
- 23 - EN
1C29
MTS(Multi-Channel Television sound)SYSTEM
You can record or listen to a program in MTS stereo.
CHECKING THE SELECTED MTS MODE
When you play a VHS tape, or receive a broadcast
on the TV/DVD/VCR tuner channel you are watching,
the status shown below will appear when you press
the DISPLAY button on the remote control.
PLAY
B
12:00AM
HIFI CH 123
STEREO/SAP
SP COUNT 0:00:00
1] When a program is broadcast in stereo, STEREO
appears on the TV screen.
2] When a program is broadcast in second audio,
SAP appears on the TV screen.
3] When a program broadcast both in stereo and sec-
ond audio, STEREO and SAP appear on the TV
screen.
NOTE: Although a program may be broadcast in
both stereo and second audio, you cannot
record in both stereo and second audio at
the same time.
4] While the TV/DVD/VCR is set in HIFI stereo
mode and playback mode. HIFI appears on the
TV screen. While the TV/DVD/VCR is set in
monaural(MONO) mode, HIFI disappears from
the TV screen.
NOTE: If you play non-HIFI tapes while the
TV/DVD/VCR is set in HIFI, HIFI will dis-
appear from the TV screen and the
TV/DVD/VCR will play automatically in
monaural.
MTS RECORDING/MONITOR MODE
Type of broadcast Display on STEREO/SAP Hi-Fi audio track(2-channel) Normal audio
the TV screen SELECTION L-channel R-channel track
Regular -None- -Invalid- Mono Mono Mono
(monaural audio)
Stereo broadcast STEREO -Invalid- L R L+R
Bilingual broadcast SAP STEREO* Main audio Main audio Main audio
program program program
SAP* Sub audio Sub audio Sub audio
program program program
Stereo & Bilingual STEREO STEREO* L R L+R
broadcast SAP
SAP* sub audio sub audio sub audio
program program program
*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.
2]
3]
1]
4]
SAP
Second Audio Program, which means your
program, can also be received in a second
language or sometimes a radio station.
HIFI
High Fidelity which produces better sound
than standard stereo TV/DVD/VCRs.
TV/VCR
TV/VCR
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 23
- 24 - EN
1C29
SELECTING THE MTS SYSTEM
Make sure ...
•
TV/DVD/VCR power must be turned on.
TO SELECT HIFI MODE
1 Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”. Then,
press the ENTER button.
2 Select“VCR AUDIO”
Press the Arrow button K or L to
point to“VCR AUDIO”.
3 Select [HIFI]
Press the ENTER button until
[HIFI] appears.
4 To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
NOTES:
•
Normally, “HIFI” should be selected for playback
with HIFI sound.
•
When you play non-HIFI tapes, the TV/DVD/VCR
will play automatically in the monaural mode.
•
The TV/DVD/VCR records automatically MTS
broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
TO SELECT STEREO, SAP, OR MONO
1 Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
2 Select “TV AUDIO”
Press the Arrow button K or L to
point to“TV AUDIO”.
3 Select [STEREO], [SAP], or [MONO]
Press the ENTER button until [STEREO], [SAP], or
[MONO] appears.
4 To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
NOTES:
•
You must select the recording mode,either TV
AUDIO [STEREO] or [SAP] when you record a
broadcast.
Refer to
“MTS RECORDING/MONITOR
MODE”.
•
If you select second audio when second audio is
not
available, the TV/DVD/VCR will record normal
audio.
•
The TV/DVD/VCR records automatically MTS
broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
RENTAL [OFF]
REPEAT PLAY [OFF]
AUTO RETURN [OFF]
B VCR AUDIO [HIFI]
TV AUDIO [STEREO]
– USER’S SET UP –
RENTAL [OFF]
REPEAT PLAY [OFF]
AUTO RETURN [OFF]
VCR AUDIO [HIFI]
B TV AUDIO [STEREO]
– USER’S SET UP –
RENTAL [OFF]
REPEAT PLAY [OFF]
AUTO RETURN [OFF]
B VCR AUDIO [HIFI]
TV AUDIO [STEREO]
TO SELECT MONO MODE
You can change the selection to “MONO” if you
want to listen to HIFI tapes in normal audio play-
back.
1)
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S
SET UP”.Then, press the ENTER button.
2) Press the Arrow button K or L to point to
“VCR AUDIO”.
3) Press the ENTER button until [MONO] appears.
4) Press the SETUP button on the remote control to
return to TV mode.
TV/VCR
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 24
- 25 - EN
1C29
VIDEO CASSETTE
This TV/DVD/VCR will operate with any cassette that has the mark. For best results,
we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
REMOVING A CASSETTE
1)In the Stop mode, press the EJECT button on the
remote control or press the STOP/EJECT button on
the TV/DVD/VCR. The cassette will eject.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
NOTE:
• In DVD mode, Whether the cassette is with tab or
without tab you insert, it doesn’t start playing until
you press the PLAY button.
In TV/VCR mode, if th cassette without tab is
inserted, playback will automatically start.
PRECAUTIONS
•
Avoid moisture. Moisture condensation may occur
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your TV/DVD/VCR, wait until the tape has
warmed to room temperature and the moisture has
evaporated.
•
Avoid extreme heat, high humidity and magnetic
fields.
•
Do not tamper with the cassette mechanism.
•
Do not touch the tape with your fingers.
INSERTING A CASSETTE
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the TV/DVD/VCR. The
TV/DVD/VCR will automatically turn on.
TWO DIFFERENT TAPE SPEEDS
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/play-
back time using T60, T120 or T160 tapes in each
mode.
Note: You can play back a tape recorded in LP mode
(Long Play).
Tape Speed Recording/Playback Time
Type of tape
T60 T120 T160
SP mode 1 hour 2 hours 2-2/3 hours
SLP mode 3 hours 6 hours 8 hours
ERASE PREVENTION
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
If you decide to record on
the tape again, cover the
hole with plastic tape.
CORRECT
Window
WRONG
Tab
Transparent Tape
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 25
- 26 - EN
1C29
PLAYBACK
NORMAL PLAYBACK
Make sure ...
•
TV/DVD/VCR power must be turned on.
1 Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/DVD/VCR will start playback automatically.
2 To begin playback
Press the PLAY button.
3 To stop playback
Press the STOP button when play-
back is completed.
NOTES:
•
If you press the PLAY button (of the TV/VCR side)
in the DVD mode, you can start the VCR playback.
•
If you press the SELECT button in the VCR play-
back, it will stop and the mode will change to the
DVD mode. In addition, the same function oper-
ates with the DVD side PLAY button or the
OPEN/CLOSE button.
TV/VCR
TRACKING ADJUSTMENT
•
Tracking adjustment will be set automatically
(Digital Tracking function) when you start play-
back.
•
However when playing pre-recorded tapes or tapes
recorded on units other than your own, noise lines
(black and white streaks) may appear on the play-
back picture. If this occurs, you can adjust the
tracking control manually by pressing the CHAN-
NEL button K or L until the streaks disappear. To
return to the DTR function, stop the tape once and
start playback again.
•
You can reduce the noise lines by pressing the
CHANNEL button K or L in slow mode, too.
Tracking adjustment in Slow mode will not be set
automatically.
TV/VCR
PICTURE SEARCH
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD or REW button during playback. (in the
SP / LP / SLP modes)
NOTE:
•
If you press the F.FWD or REW button on the
front panel in the DVD mode, the VCR forward
or reverse will start. Please press the STOP /
EJECT button once to stop it, twice to eject it.
2)
Press it again and the TV/DVD/VCR will now search
in super high speed. (in the LP / SLP modes only)
NOTE:
•
Tapes recorded in the SP or LP mode will dis-
play a noise bar on the TV screen and the picture
may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
TV/VCR
STILL PICTURE
You can view a still picture on the TV screen during playback
(the Still mode). Press the PAUSE button during playback.
Only tapes recorded in the SLP mode will show the least
amount of lines.Press the PLAY button to return to playback.
NOTES:
•
You can advance the picture one frame at a time by
pressing the PAUSE button during the Still mode.
•
If it is left in the Pause mode for more than five
minutes, the TV/DVD/VCR will automatically
switch to the Stop mode.
TV/VCR
VERTICAL HOLD CONTROL
In the Pause/Still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
the CHANNEL button K or L.
NOTE:
If there are video noise lines on the screen, see Tracking
Adjustment section.
TV/VCR
SLOW MOTION
During pause, press the FWD button to reduce the
playback speed. The TV/DVD/VCR mutes the sound
during slow motion. Press the PLAY button to return
to normal playback.
NOTE: If it is left in the Slow mode for more than
five minutes, the TV/DVD/VCR will automatically
go into the Stop mode.
TV/VCR
PLAY
B
STOP
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 26
- 27 - EN
1C29
SPECIAL PLAYBACK
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1 Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then, press the ENTER button.
2 Set “RENTAL” to [ON]
Press the Arrow button K or L to
point to “RENTAL”.
Press the ENTER button until [ON]
appears.
3 Exit the Rental setting
Press the SETUP button on the remote control to
return to the TV mode.
4 Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
•
Once you select the Rental mode, it stays in effect
even after you turn off the TV/DVD/VCR.
TO CANCEL THE RENTAL MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV
mode.
If there is a power failure of any kind, the
tv/vcr/dvd will retain its memory for this feature.
TV/VCR
Make sure ...
•
TV/DVD/VCR power must be turned on.
•
Insert a prerecorded tape.
RENTAL PLAYBACK
The TV/DVD/VCR has the auto repeat function that
allows you to repeat a tape indefinitely without
touching the PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the begin-
ning to a blank part, which is blank for more than
10 seconds.
1 Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then, press the ENTER button.
2 Select “ALL” or “BLANK”
Press the Arrow button K or L to
point to “REPEAT PLAY”.
Press the ENTER button repeatedly
until your desired selection [ALL]
or [BLANK] appears.
3 Exit the Repeat Play setting
Press the SETUP button on the remote control to
return to the TV mode.
4 Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY B” appears.
•
Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/DVD/VCR.
•
If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV
mode.
If there is a power failure of any kind, the
TV/DVD/VCR will retain its memory for this fea-
ture.
TV/VCR
AUTO REPEAT PLAYBACK
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
–
USER’S SET UP
–
B RENTAL [ON]
REPEAT PLAY [OFF]
AUTO RETURN [OFF]
VCR AUDIO [HIFI]
TV AUDIO [STEREO]
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
–
USER’S SET UP
–
RENTAL [OFF]
B REPEAT PLAY [ALL]
AUTO RETURN [OFF]
VCR AUDIO [HIFI]
TV AUDIO [STEREO]
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 27
- 28 - EN
1C29
SEARCH
Make sure ...
•
TV/DVD/VCR power must be turned on.
•
Insert a tape.
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
1 Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
2 Reset the counter to 0:00:00
Press the C.RESET button repeatedly.
3 Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is
completed.
4 To activate “ZERO RETURN” mode
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “ZERO RETURN”.
Then, press the ENTER button.
The counter will appear on the TV screen.
The tape will automatically stop when the counter
returns to 0:00:00.
TV/VCR
ZERO RETURN
The Time Search function makes it possible to quick-
ly advance the tape to your desired position simply
by entering the exact amount of playback time you
want to skip.
NOTES:
•
Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
TV/VCR
TIME SEARCH
•
This function will not operate in recording mode.
•
This function is not operative when a cassette tape
is not inserted in the TV/DVD/VCR.
In the example below: To watch a program after 2
hour 50 minutes from the present position, in either
direction.
1 Insert a tape.
2 Select “TIME SEARCH” mode
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “TIME SEARCH”.
Then, press the ENTER button.
3 Enter your desired time
Press the Arrow button K or L until
your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
If you wish to cancel the Time
Search at this point, press the SETUP button on the
remote control.
4 Begin Time Search
By pressing the Arrow button s or B, the
TV/DVD/VCR will rewind or fast forward to the
specified point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
TO CANCEL THE TIME SEARCH at this
point
Press the STOP/EJECT button on the TV/DVD/VCR
or the STOP button on the remote control. This will
delete the selected time.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B ZERO RETURN
TIME SEARCH
INDEX SEARCH
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B TIME SEARCH
INDEX SEARCH
TIME SEARCH
2 : 50
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 28
- 29 - EN
1C29
INDEX SEARCH
This feature provides a method of indexing the start-
ing point so that it can be easily returned to in either
fast forward or rewind mode.
•
The index mark will be made automatically when
the REC button is pressed. It will also be marked at
the starting point of Timer recording and OTR.
•
The index mark will not be recorded if the PAUSE
button is pressed and released during recording.
•
The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 min-
utes for SLP recording.
•
In some cases, the index mark at the beginning of
video tape cannot be detected.
Example: You are watching program number 4 and
want to fast forward to program number 7. You
must skip three programs.
TV/VCR
1 Select “INDEX SEARCH”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “INDEX SEARCH”. Then,
press the ENTER button.
2 Enter your desired number
Press the Arrow button K or L until
the number of programs that you
want to skip appears.
(Example: “03” for 3 programs)
•
The Index Search mode will be
canceled if the procedures are not activated in 30
seconds.
3 Begin Index Search
Press the Arrow button s or B. The TV/DVD/VCR
begins rewinding or fast forwarding to the beginning
of desired program.
NOTE: Every time an index signal is skipped, the
number in the program indicator decreases by one.
4 After Index Search
When the preset program is reached, the
TV/DVD/VCR will start playback automatically.
•
A video cassette must be inserted in the
TV/DVD/VCR for this function to work.
•
The number of Index Searches can be set up to 20.
•
This function will not operate in the recording mode.
•
When you want to cancel the Index Search while
in progress, press the STOP button.
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7
4321123
End of tape
Beginning of tape
CURRENT PLAYBACK PROGRAM
INDEX MARK
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B INDEX SEARCH
INDEX SEARCH
0 3
SPECIAL FEATURES
REAL TIME TAPE COUNTER
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time will
not change on a blank tape or blank portions on the
tape.)The “–” indication will appear when the tape has
rewound further than “0:00:00” on the tape counter.
TV/VCR
AUTO REWIND-EJECT
•
When the end of a tape is reached during record-
ing, playback, or fast-forward, the tape will auto-
matically rewind to the beginning. After rewinding
finishes, the TV/DVD/VCR will eject the tape and
turn itself to off.
•
This function is operative when Repeat Play is set
to the [OFF] position.
•
The tape will not auto-rewind during timer record-
ing or One Touch Recording.
TV/VCR
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 29
- 30 - EN
1C29
RECORDING
Make sure ...
•
TV/DVD/VCR power must be turned on.
•
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
NOTES:
•
This TV/VCR/DVD will ONLY record and view the same channel.
•
This TV/VCR/DVD cannot record the contents from the built-in DVD.
You can ONLY watch the same TV program that is
being recorded.
1 Select the channel to be
recorded
Press the number buttons on the
remote control or the CHANNEL
button K or L.
Remember: If the TV/DVD/VCR is connected to a
cable box or satellite box, the TV/DVD/VCR must
be on CH3 or CH4, then the channel to be recorded
must be selected on the cable box or satellite box.
2 Select the tape speed
Press the SPEED button to select
the desired tape speed (SP/ SLP).
3 Begin recording
Press the RECORD button.
4 Stop recording
Press the STOP button when recording is completed.
TV/VCR
NORMAL RECORDING
Press the PAUSE button to tem-
porarily stop recording.
Press the PAUSE or RECORD but-
ton to resume recording.
NOTES:
•
After five minutes, the TV/DVD/VCR will auto-
matically switch to the Recording mode to prevent
tape damage.
•
If “CLOSED CAPTION (ON)” is selected, the On-
Screen Display will appear for 5 seconds, then dis-
appear.
TV/VCR
SKIPPING UNWANTED
SCENES DURING RECORDING
CH 10
SP
REC
SP
PAUSE
SP
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 30
- 31 - EN
1C29
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/DVD/VCR.
Make sure ...
•
TV/DVD/VCR power must be turned on.
•
Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
NOTES:
•
This function CANNOT be done from the remote
control.
•
Recording starts immediately when the REC/OTR
button is pressed.
•
When the REC/OTR button is pressed 18 times, the
TV/DVD/VCR returns to the Normal Recording mode.
•
To stop the OTR operation, press the STOP button
on the TV/DVD/VCR or on the remote control.
•
To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up momen-
tarily then disappear.)
•
Recording stops when 0:00 is reached.
•
Please note that in the SLP mode maximum record-
ing time, assuming the tape is started at the begin-
ning, is 8 hours using T-160 (or 6 hours using T-120).
•
If the tape runs out before the end time, the
TV/DVD/VCR will switch to the Stop mode
immediately, ejects the tape and turns itself off.
•
If you press the POWER button during OTR, the
TV/DVD/VCR continues recording until the select-
ed length is reached.
1 Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL button K or L.
Remember: If the TV/DVD/VCR is connected to a
cable box or satellite box, the TV/DVD/VCR must
be on CH3 or CH4, then the channel to be recorded
is selected on the cable box or satellite box.
2 Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3 Begin OTR
Press the REC/OTR button on the
TV/DVD/VCR as many times as
needed. The recording length will be
determined by the number of times
you press the REC/OTR button. Each
additional push will increase the recording time by 30
minutes. It is set up to 8 hours.
TV/VCR
OTR (One Touch Recording)
Push(es) Display Recording length
1 push (normal recording)
2 pushes 0:30 30 minutes
3 pushes 1:00 60 minutes
17 pushes 8:00 480 minutes
You can make copies of video tapes made by friends
or relatives for your enjoyment.
You can not copy a DVD to a videotape.
Connect your TV/DVD/VCR and a Source (Playing)
VCR using the following diagram.
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to
record over, into the TV/DVD/VCR’s cassette
compartment.
3)Press the SPEED button on remote control for the
TV/DVD/VCR to select the desired recording
speed (SP/SLP).
4)Press the CHANNEL button K or L on the
TV/DVD/VCR until “AUX” appears on the screen.
5)Press the RECORD button on the TV/DVD/VCR.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/DVD/VCR’s front panel controls whenever pos-
sible. The remote control might affect the source
(Playing) VCR’s playback operation.
TV/VCR
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
[Fig.8]
[Ex: Source (playing)
VCR or camcorder]
Audio/Video
adapter cable
(not supplied)
[The TV/DVD/VCR]
OTR(2 : 30)
SP
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 31
- 32 - EN
1C29
TIMER
You may set the TV/DVD/VCR to start and end a
recording while you are away. You can set 8 pro-
grams to record on specific days, daily or weekly
within a 1 year period.
In the example below, the timer is being set to record:
DATE: July 4th, 2003
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL: CH61
TAPE SPEED: SP
Make sure ...
•
If a cable box or satellite box is connected with the
TV/DVD/VCR you will be limited to record only one
channel. And the channel selector on the
TV/DVD/VCR must be selected to the output channel
of the boxes CH 3 or CH 4 and then the actual chan-
nel to be recorded must be selected on the boxes.
•
Clock must be set to the correct time and date
before setting the timer.
•
TV/DVD/VCR power must be turn on to program it.
•
Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
•
The channel you want to record is properly set in
advance. (See page 16.)
Avoid over lap of programs ...
There is a chance that a program will not be record-
ed. when programs overlap;
•
The program with an earlier start has priority.
•
Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
•
The illustration below demonstrates the sequence
of recordings.
Program 1 10:00AM - 11:00AM
Program 2 9:00AM - 10:00AM
Program 3 9:30AM - 12:00PM
TV/VCR
AUTOMATIC TIMER
RECORDING
9:00AM 10:00AM 12:00PM
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
11:00AM
Recording Sequence
*Recording period is SHADED
1 Select “TIMER PROGRAMMING”
Press the SETUP button on the
remote control.
Confirm “TIMER PROGRAM-
MING” is pointed by pressing the
Arrow button K. And press the
ENTER button.
•
If you have not yet set the clock, “MANUAL
CLOCK SET” appears. If so, follow stops [3] to
[8] on page 17. Then set the timer recording.
2 Select your desired program
position (1~8)
Press the Arrow button K or L to
select the desired program position.
Then, press the Arrow button B.
3 Set the channel number
Press the Arrow button K or L until
the desired channel number
appears. (Example: CH61)
Then, press the Arrow button B.
Remember: If the TV/DVD/VCR is
connected to a cable box or satellite box, the
TV/DVD/VCR must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box or
satellite box.
4 Select once, every day or weekly recording
For once recording :
Press the Arrow button K (up)
until the desired date appears.
(Example: “7/04” for July 4th).
Then, press the Arrow button B.
For every day recording : To record a TV program
at the same time on the same channel every day.
(Example: Monday through Sunday)
Press the Arrow button L (down)
until “EVRY DAY” appears.
Then, press the Arrow button B.
For weekly recording : To record a TV program at
the same time on the same channel every week.
(Example: every Monday)
Press the Arrow button L (down)
until “EVRY” and your desired
day of the week appear together.
Then, press the Arrow button B.
- TV/VCR SETUP -
B TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 EVRY DAY -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 7/04 FRI -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 EVRY MON -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 32
- 33 - EN
1C29
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
2)Repeat step [1] on page 32.
3)Press the RECORD button and select the desired
program using the Arrow button K or L.
4)Press the RECORD button again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the PAUSE but-
ton on the remote control. The recording time
returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automati-
cally be set to the SLP mode.
5)Press the ENTER or RETURN button to exit the
setting menu. Then press the SETUP button on the
remote control to return to original mode.
TO CORRECT A PROGRAM
•
While setting a program; press the Arrow button
s to go back one step and enter the correct num-
bers using the Arrow button K or L.
•
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] - [2] on page 32.
3)Press the Arrow button B (or press the Arrow
button s to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the Arrow button K or L.
4)Press the POWER button to set automatic timer
recording.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
•
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] ~ [2] on page 32 and select a
program you want to cancel.
3)Press the C.RESET button.
4)Press the SETUP button on the remote control to
return to TV mode.
•
While recording is in progress;
1)Press the POWER button.
2)Press the STOP/EJECT button on the
TV/DVD/VCR.
TV/VCR
5 Set beginning hour
Press the Arrow button K or L until
the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then, press the Arrow button B.
6 Set beginning minute
Press the Arrow button K or L until
the desired minute appears.
(Example: “30” for 7:30PM)
Then, press the Arrow button B.
7 Set end hour
Press the Arrow button K or L until
the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the Arrow button B.
8 Set end minute
Press the Arrow button K or L
until the desired minute appears.
(Example: “50” for 8:50PM)
Then, press the Arrow button B.
9 Set the tape speed
Press the Arrow button K or L
until the desired tape speed
appears. (Example: SP)
10 Finish setting the program
Press the ENTER or RETURN button. The program
is now completed.
•
To set another program, repeat steps [2] to [10].
•
Press the SETUP button on the remote control to
return to original mode.
11 Set the timer
Press the POWER button to set automatic timer
recording. The RECORDING indicator lights up.
•
You must turn off the TV/DVD/VCR to activate
automatic timer recording.
If power is not turned off and you continue watch-
ing TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
TIMER PROGRAM EXTENSION
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 7/04 FRI 7:12
P
M
-:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 7/04 FRI 7:30
P
M
-:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 7/04 FRI 7:30
P
M
8:30
P
M
- -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 7/04 FRI 7:30
P
M
8:50
P
M
- -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
B
61 7/04 FRI 7:30
P
M
8:50
P
M
SP
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
- - -/- - - - - -:- - -:- - - -
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 33
- 34 - EN
1C29
TO CHECK THE BEGIN/END TIME
1)Press the POWER button so that the RECORDING
indicator goes off.
2)Press the SETUP button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the ENTER button. The details of programs
appear on the TV screen.
5)Press the SETUP button on the remote control to
return to TV mode.
HINTS FOR AUTOMATIC
TIMER RECORDING
•
Make sure the channel you want to record is prop-
erly set in advance.
•
It is not necessary to press the RECORD button for
timer recording.
•
Recording begins automatically at the Start time.
•
If you are recording using a Timer mode, you may
not operate the TV/VCR/DVD manually.
•
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
•
If the erase-prevention tab is removed, the cassette
will be ejected when the POWER button is pressed
to off.
•
If the tape runs out before the end time, the
TV/DVD/VCR will switch to the Stop mode
immediately, and the tape will be ejected.
TV/VCR
AUTO RETURN
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
1 Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button
K or L to
point to “USER’S SET UP”.
Then, press the ENTER button.
2 Set “AUTO RETURN” to [ON]
Press the Arrow button K or L to
point to “AUTO RETURN”.
Press the ENTER button until [ON]
appears.
TV/VCR
3 Auto Return will begin
When all the timer recordings are completed, the
TV/DVD/VCR will rewind to the beginning of the
recorded program(s).
NOTE:
•
If you press the POWER button while tape is
rewinding, the Auto Return will stop.
4 Watch the recorded program
Press the PLAY button.
TO CANCEL THE AUTO RETURN
MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button.
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this fea-
ture.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
–
USER’S SET UP
–
RENTAL [OFF]
REPEAT PLAY [OFF]
B AUTO RETURN [ON]
VCR AUDIO [HIFI]
TV AUDIO [STEREO]
SLEEP TIMER
The Sleep Timer function turns off the
TV/DVD/VCR without using the POWER button
after a desired period of time.
NOTE:
•
This function does not operate during Recording
mode.
TV/VCR
1 Select “SLEEP TIMER”
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears.
2 Set sleep time
Press the SLEEP button until your
desired sleep time appears.
Each additional push will increase
the time by 30 minutes up to 120
minutes.
After 5 seconds, exit the Sleep Timer setting.
TO CANCEL THE SLEEP TIMER
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears. Press the SLEEP button
until “SLEEP 0 MINUTES” appears.
SLEEP 120 MINUTES
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 34
- 35 - EN
1C29
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
When the Closed Caption mode is OFF:
•
Counter mode: After 5 seconds, only the counter
remains. To clear it, press the DISPLAY button.
•
Clock mode: After 5 seconds, only the clock and
the channel number remain. To clear them, press
the DISPLAY button.
When the Closed Caption mode is ON:
•
The On Screen Display disappear after 5 seconds.
•
This is true even if the MUTE button is pressed, or
the PAUSE button is pressed while recording.
OFF mode Clock/Counter mode
STOP 5:40 PM
CH2
SP COUNT 0:12:34
STOP STOP
SP SPCOUNT 0:12:34
COUNT 0:12:34
5:40PM
CH2
5:40PM
CH2
Counter
remains
Clock & Channel
remains
After 5 seconds After 5 seconds
OFF mode Counter mode Clock mode
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
TV Display
TV Display
TV Display
TV Display
TV Display
TV Display
TV Display
TV Display
CATV channel
TV Display
W+80 W+81 W+82 W+83 W+84
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
W+55 W+56 W+57 W+58 A-4 A-3 A-2 A-1 W+59 W+60 W+61 W+62 W+63 W+64
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
A-5
R S T U V W W+1 W+2 W+3 W+4 W+5 W+6 W+7 W+8 W+9
CDEFGHI JKLMNOPQ
5A 2 3 4 5 6 7 8 9 10 11 12 13 A B
123456789101112131415
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
91 92 93 94 95 96 97 98 99 100 101 102 103 104 105
106 107 108 109 110 111 112 113 114 115 116 117 118 119 120
121 122 123 124 125
CATV channel
CATV channel
CATV channel
CATV channel
CATV channel
CATV channel
CATV channel
CATV channel
TD851/951(P01-35).QX33 03.3.1 1:53 PM Page 35
–
36
–
EN
01A11
DVD SECTION
ABOUT THE DISCS
DISC TYPES
The following discs can be played back on this
TV/DVD/VCR.
¡
DVD video
¡
DVD-R/RW*
¡
DVD+R/RW*
¡
Audio CD
¡
CD-R/RW*
¡
MP3*
* Depending on the types or the writing method of the
medium some discs can not be played.
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs
made on personal computers, or on DVD recorders may
not be played back properly due to the factors such as
scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played
back properly due to the different environment or the
settings of the application you use. We recommend
always to use the standardized, rightly formatted discs.
(Please contact the sales agency for more detail).
This player conforms to the NTSC color system. You can-
not play discs recorded in other color systems such as
PAL or SECAM.
¡Some discs include region codes as shown below.
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on TV/DVD/VCR with the
same region code.
The following discs cannot be played back on this
TV/DVD/VCR.
¡
DVD with region codes other than 1 or ALL.
¡
DVD-ROM
¡
DVD-RAM (Never play back, otherwise malfunc-
tion may result.)
¡
CD-ROM
¡
VSD
¡
CDV (Only plays back the audio part.)
¡
CD-G (Only plays back the sound.)
¡
CD-I (Never play back, otherwise malfunction
may result.)
¡
SACD
¡
Photo CD (Never play back, otherwise malfunc-
tion may result.)
¡
Video CD (Never play back, otherwise malfunc-
tion may result.)
Any other discs without compatibility indications.
PLAYABLE DISCS
[
DVD
]
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback con-
ditions take priority over user operations on this player. If
a function you selected does not run as desired, refer to
the manual accompanying the disc.
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Chapter 4
[
AUDIO CD
]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
[
MP3
]
Data on an MP3 is divided into sections called "groups",
and then into subsections called "tracks", each of which is
given a group or track number.
Example
Group 1 Group 2
Track 1 Track 2 Track 1 Track 2Track 3 Track 4
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 36
–
37
–
EN
01A11
PLAYING A DISC
BASIC PLAYBACK
Getting started
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
1 Press the POWER button.
¡The power will turn on.
2 Press the OPEN/CLOSE button to open disc
loading tray.
3 Place the chosen disc in the tray, with the
label facing up.
CD
DVD-V
4 Press the PLAY button.
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
the PLAY button.
¡When you playback the DVD which a title menu is
recorded, it may appear on the screen. In this case,
refer to “TITLE MENU”.
5 Press the STOP button to stop playback.
NOTES
¡When the DVD mode has been switched to the
TV/VCR mode, the DVD mode shuts down first and
then TV picture and sound appears in about 4 seconds.
Similarly, when the POWER button is pressed to turn
off in the DVD mode, this mode shuts down first and
then the TV/DVD/VCR’s power is turned off.
¡A “prohibited icon” may appear at
the top-right on the TV screen dur-
ing operation, warning that a pro-
hibited operation has been encoun-
tered by the DVD or the disc.
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title, or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
GENERAL FEATURES
DVD may contain menus to navigate the disc and
access special features. Press the appropriate number
buttons or use the Arrow buttons (L/K/s/B) to high-
light your selection in the DVD main menu and press
the ENTER button to confirm.
NOTES
¡Select DVD mode by pressing the SELECT button on
the remote control. Then, operate the DVD functions.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
TITLE MENU
1 Press the TITLE button.
¡The title menu will appear.
2 If the feature is not available, symbol
may appear on the TV screen.
3 Press the Arrow buttons (L/K/s/B) to
select an item, and the ENTER button to
confirm selection.
DVD-V
DISC MENU
1 Press the DISC MENU button.
¡The DVD main menu will appear.
2 If the feature is not available, symbol
may appear on the TV screen.
3 If disc menu is available on the disc, audio
language, subtitle options, chapters for the
title and other options will appear for selec-
tion.
4 Press the Arrow buttons (L/K/s/B) to
select an item, and the ENTER button to
confirm selection.
DVD-V
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVD-Vs
¡Press the DISC MENU button to call up the DVD menu.
¡Press the TITLE button to call up the title menu.
NOTE
¡Contents of menus and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 37
–
38
–
EN
01A11
STEP BY STEP PLAYBACK
1 During playback, press the PAUSE button.
¡Playback will pause and sound will be muted.
2 The disc goes forward by one frame each
time the PAUSE button is pressed.
3 To exit step by step playback, press the
PLAY button.
DVD-V
RESUME
1 During playback, press the STOP button.
¡Resume message will appear on the TV screen.
2 Press the PLAY button, playback will resume
from the point at which playback was stopped.
¡To cancel resume, press the STOP button twice.
¡If turn off the TV/DVD/VCR, resume function will
be cancelled.
CD
DVD-V
1 During playback, press and hold down the FWD
g or REV h button for a few seconds.
2 Each press and hold down the FWD g or
REV
h button repeatedly to select the
required speed: x2, x8, x50, x100.
¡For audio CDs, the speed is fixed at ×16.
¡For MP3, the speed is fixed at ×8.
3 To return to normal playback, press the
PLAY button.
Note for using buttons on the main unit:
During playback, press and hold down the SKIP G /
SEARCHg buttons or the SKIPH /SEARCHh
buttons on the TV/DVD/VCR for a few seconds to begin
Search in x2 speed. Press and hold down again to change
speed to x8. Repeat this procedure to change to x50 and
x100.
MP3CD
DVD-V
FAST FORWARD/REVERSE
SEARCH
PAUSE
1 During playback, press the PAUSE button.
¡Playback will pause and sound will be muted.
2 To continue playback, press the PLAY button.
CD
DVD-V
SLOW FORWARD /
SLOW REVERSE
1 During playback, press the PAUSE button.
2 Press and hold down the FWD g or REV
h button for a few seconds.
3 Each press and hold down the FWD g or
REV
h button repeatedly to select the
required speed: 1/16, 1/8, 1/2 of the normal
playback.
4 To return to normal playback, press the
PLAY button.
Note for using buttons on the main unit:
Press the PAUSE button, then, press and hold down the
SKIP G / SEARCHg buttons or the SKIPH
/SEARCHh buttons on the TV/DVD/VCR for a few
seconds to begin Search in 1/16 speed of the normal
playback. Press and hold down again to change speed
to 1/8. Repeat this procedure to change to 1/2.
DVD-V
ZOOM
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
1 Press the ZOOM button during playback.
¡Playback will continue.
2 Press the ZOOM button repeatedly to select
the required zoom factor: ZOOM1, ZOOM2,
ZOOM3, or OFF.
3 Use the Arrow buttons (K/L/s / B) to
move the zoomed picture across the
screen.
4 To exit zoom mode, press the ZOOM button
to OFF.
NOTES
¡Zooming function does not work while disc menu is
shown.
¡Zooming function is not available on some discs.
DVD-V
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 38
–
39
–
EN
01A11
SEARCH FUNCTION
TRACK SEARCH
There are three ways to begin playback on an Audio
CD at a specific Track.
Using the Number buttons on the remote control
1 Press the Number buttons to enter the
desired Track number.
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡To play track 26, press +10, 2, 6.
Using the SEARCH MODE button
1 Press the SEARCH MODE button.
¡The track search display appears.
2 Within 30 seconds, select a desired track
number using the Number buttons on the
remote control.
¡For single digits press 0 first.
¡Playback will start at the selected track.
Using the SKIP
HG
buttons
During playback, press the SKIP G button to move
the next track. Press it repeatedly to skip subsequent
tracks. Press the SKIP H button to go back to begin-
ning of the current track. Press it repeatedly to go to
the previous tracks.
¡If the SKIP button is pressed while the playback is
paused, the playback will be paused again after skip-
ping to the next track.
NOTE
¡The SKIP HGbuttons are not available when
playback is stopped.
CD
TITLE / CHAPTER SEARCH
1 Press the SEARCH MODE button once for
the Chapter search, twice for the Title
search during playback.
2 Enter the desired chapter/title number using
the Number buttons on the remote control.
¡Playback will start at the selected Chapter or Track.
¡Press the CLEAR button to erase the incorrect input.
¡For single digits press 0 first.
DVD-V
/2
TIME SEARCH
1 During playback, press the SEARCH MODE
button three times (CD: twice) to display the
Time Search on the TV screen.
2 Within 30 seconds, enter a desired disc
time using the Number buttons on the
remote control.
¡Playback will start at the specified time.
¡Press the CLEAR button to erase the incorrect input.
CD
DVD-V
MARKER SETUP SCREEN
Use markers to memorise your favorite places on a
disc.
1 Press the SEARCH MODE button four times
(CD: three times) during playback.
¡The display screen and Markers will appear on the
TV screen.
2 Press the Arrow buttons (s/ B) to select 1,
2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “- :
- - : - -” appears in the display.
3 When reaches the desired point, press the
ENTER button.
¡The Title or Track and elapsed playing time will
appear in the TV screen.
4 To return to the Marker later, press the
SEARCH MODE button four times (CD: three
times) during playback and the Arrow but-
tons (
s/ B) to choose the desired marker,
then press the ENTER button.
NOTES
¡Opening the disc tray or turning off the power or
select AC at step 2 and press the ENTER button will
erase all Markers.
¡To clear a marker, using the Arrow buttons (s / B
)
,
position the cursor on to the marker number to be
cleared and press the CLEAR button.
¡You can mark up to 10 points.
5 Press the SEARCH MODE or RETURN but-
ton to exit.
CD
DVD-V
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 39
–
40
–
EN
01A11
SPECIAL PLAYBACK FUNCTION
REPEAT
REPEAT TITLE / CHAPTER
To activate the repeat function, press the
REPEAT button during playback.
¡The repeat mode changes as described below every
time you press the button.
DVD-V
REPEAT is available only during playback.
CHAPTER TITLE OFF
(current chapter repeat) (current title repeat)
(repeat off)
NOTES
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
REPEAT TRACK
To activate the repeat function, press the
REPEAT button during playback.
¡The repeat mode changes as described below every
time you press the button.
CD
TRACK ALL OFF
(current track repeat) (entire disc repeat)
(repeat off)
NOTES
¡Repeat setting will be cleared when moving to other
track.
¡Repeat playback does not function during repeat A-B
playback.
REPEAT A-B
1 Press the REPEAT A-B button at your cho-
sen starting point.
¡ A- appears briefly on the TV screen.
2 Press the REPEAT A-B button again at your
chosen end point.
¡ A-B appears briefly on the TV screen, and the
repeat sequence begins.
3 To exit the sequence, press the REPEAT A-
B button.
NOTES
¡The repeat A-B section can only be set within the cur-
rent title (for DVDs), or current track (for audio CDs).
¡Repeat A-B is not available with some scenes in DVD.
¡To cancel the A point which was set, press the
CLEAR button.
¡Repeat A-B playback does not function during title,
chapter, track or all repeat playback.
CD
DVD-V
PROGRAM
You may determine the order in which tracks will play.
1 In stop mode, press the MODE button.
¡The PROGRAM screen will appear.
2 Press the Arrow button ▲ or ▼ to select a
track, then press the
ENTER button.
¡Press the CLEAR button to
erase the most recently entered
program.
3 Repeat step 2 until you have selected all the
tracks you want to play in the program.
4 Press the PLAY button to play the pro-
grammed tracks.
NOTES
¡While the program is being played back, the STOP
works as follows.
¡Press the STOP button once and then the PLAY but-
ton again, playback will restart from the point where
the STOP button was pressed. (Program continued)
¡Press the STOP button twice and then the PLAY button
again, playback will restart from the track in the usual
way. (Program cleared)
¡Up to 99 programs can be entered.
¡If you like to repeat the current track in the program,
press the REPEAT button repeatedly until
TRACK appears during playback. If you like to
repeat the entire program press the REPEAT button
repeatedly until ALL appears during playback.
CD
TOTAL
RANDOM PLAYBACK
This shuffles the playing order of tracks instead of
playback in the sequence.
1 In stop mode, press the MODE button twice.
¡RANDOM screen appears.
2 Press the PLAY button to start random playback.
NOTE
¡If you like to repeat the current track in the random
selection, press the REPEAT button repeatedly until
TRACK appears during playback. If you like to
repeat the entire random selection press the
REPEAT button repeatedly until ALL appears
during playback.
CD
PLAY
CD [AUDIO] TOTAL 0:45:55
RANDOM PROGRAM
- - no indication - -
RANDOM
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 40
–
41
–
EN
01A11
PLAYING A MP3 DISC
When a CD with MP3 files is in the TV/DVD/VCR,
the MP3 menu will appear on the TV screen in stop
mode.
1 In stop mode, press the Arrow buttons
(
K/L) to select the
desired group track.
¡If a group is selected, press
the Arrow
B
or ENTER but-
ton to go on to the track selec-
tion screen. Press the Arrow
buttons (K /L ) to choose a
track, then press the ENTER button.
¡If a track is selected, press the ENTER button to start
playing tracks. Starting from the one you’ve just
chosen the subsequent tracks will be played.
¡Choose FIRST PLAY to start playback from the
beginning of the listed tracks.
¡Press the TITLE button to return to the first item.
2 Press the STOP button to stop playback.
NOTES
¡Folders are known as Groups; files are known as
Tracks.
¡MP3 files are accompanied by icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 256 files can be recognized.
¡Up to 8 hierarchies can be created.
This player recommends the use of files recorded at
the below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
3
MP3
MP3 PLAYBACK
1 Press the SEARCH MODE button during
playback.
¡The FILE LIST will appear.
2 Select a desired track using the Arrow but-
tons (
K/L/s/B).
¡Press the Arrow button B when you want to go to
the next hierarchy.
¡Press the Arrow button s when you want to go back
to the previous hierarchy.
3 Press the PLAY button to start playback.
NOTES
¡Press the SEARCH MODE button to exit.
¡Some selections may take a while to be recognized.
MP3
TRACK SELECTION
RANDOM PLAYBACK
1 In stop mode, press the MODE button twice.
¡RANDOM screen appears.
2 Press the PLAY button to start random play-
back.
MP3
This feature allows you to program an MP3 disc to
play in a desired sequence.
1 In stop mode, press the MODE button.
¡The PROGRAM screen will appear.
2 Select a desired track using the Arrow but-
tons (
K/L/s/B). Then, press the ENTER
button.
¡Press the Arrow button B when you want to go to
the next hierarchy.
¡Press the Arrow button s when you want to go back
to the previous hierarchy.
¡Press the CLEAR button to erase the most recently
entered program.
3 Repeat step 2 until you have selected all the
Tracks you want to play in the program.
4 Press the PLAY button to start programmed
playback.
MP3
PROGRAM
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 41
–
42
–
EN
01A11
CHANGING THE SETTINGS
AUDIO LANGUAGE
The TV/DVD/VCR allows you to select a language
during DVD disc (if multi language available) play-
back.
1 Press the AUDIO button during playback.
2 Press the AUDIO button repeatedly to select
your desired language.
NOTE
¡Pressing the AUDIO button may not work on some
DVDs with multiple audio languages (e.g. DVDs
which allow audio language setting on the disc menu).
DVD-V
STEREO SOUND MODE
1 Press the AUDIO button repeatedly during
playback to select between STEREO, L-CH
or R-CH.
¡
STEREO - both right and left channels are active (stereo)
L-CH - only left channel is active
R-CH - only right channel is active
NOTE
¡I
f the Virtual Surround setting is ON, the sound mode
will be fixed to STEREO, and can not be changed.
CD
The DVD allows you to select a language for subtitles
during DVD disc (if available) playback.
1 Press the SUBTITLE button during playback.
2 Press the SUBTITLE button repeatedly to
select your desired subtitle language.
¡The subtitle language will be displayed on the dis-
play bar at the top of the screen.
3 To turn off subtitles, press the SUBTITLE
button repeatedly until OFF appears.
NOTES
¡
Some discs allow audio language setting/subtitle language
setting on the disc menu. (Operation varies between discs,
so refer to the manual accompanying the disc.)
¡If the desired language is not shown after pressing
the SUBTITLE button several times, the disc does
not have subtitles in that language.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 44.)
DVD-V
SUBTITLE LANGUAGE CAMERA ANGLE
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change
the camera angle when the ( ) icon appears on the
screen.
1 Press the ANGLE button during playback.
¡The selected angle will be displayed on the display
bar at the top of the screen.
2 Press the ANGLE button repeatedly to
select your desired angle.
DVD-V
Adjust the Black Level Settings to make the black
parts of the picture brighter.
1 Press the MODE button during playback.
2 Press the ENTER button to switch OFF.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
3 Press the MODE button twice or the
RETURN button to exit.
DVD-V
BLACK LEVEL SETTING
You can enjoy stereophonic visual space on your exist-
ing stereo system.
1 Press the MODE button twice (CD/MP3:
once) during playback.
2 Press the ENTER button to set it 1 (Natural
effect) or 2 (Emphasized effect) or OFF.
3 Press the MODE or RETURN button to exit.
NOTE (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
MP3CD
DVD-V
VIRTUAL SURROUND
ON
OFF
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 42
–
43
–
EN
01A11
For DVD-Vs
1 Press the DISPLAY button during playback
to show current Chapter.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
2 Press the DISPLAY button again to show
current Title.
¡The elapsed and remaining playing time of the cur-
rent title will be displayed.
3 Press the DISPLAY button again.
¡The BIT RATE and the current repeat setting will be
displayed.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
4 Press the DISPLAY button again to exit the
display.
THE ON-SCREEN INFORMATION
For audio CDs
1 Press the DISPLAY button during playback
to show the current Track.
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
2 Press the DISPLAY button again to show
current Total Track.
¡The elapsed and remaining playing time of the cur-
rent total track will be displayed.
3 Press the DISPLAY button again to exit the
display.
You can check the information about the current disc by pressing the DISPLAY button on the remote control.
MP3CD
DVD-V
9/49 0:00:00 -0:00:00
For MP3
1 Press the DISPLAY button during playback.
¡The name of the file currently in play will be dis-
played.
2 Press the DISPLAY button repeatedly to
show the track number, the repeat status,
and the playback status at the top of the
screen.
¡ will be displayed when repeat play has been
selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates Disc repeat
3 Press the DISPLAY button again to exit the
display.
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 43
–
44
–
EN
01A11
CHANGING THE DVD SETUP ITEMS
LANGUAGE SETTING
Language options are not available with some discs.
1 Press the SETUP button twice in STOP
mode so that the DVD SETUP menu
appears.
¡ If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
2 Press the Arrow button B to select CUS-
TOM, then press the ENTER button.
¡CUSTOM mode will appear.
3 Press the Arrow buttons (s/ B) to select
LANGUAGE, then press the ENTER button
to confirm.
4 Press the Arrow buttons (K/L) to select the
next items, then press the ENTER button.
AUDIO:
¡Sets the audio language.
SUBTITLE:
¡Sets the subtitle language.
DISC MENU:
¡Sets the language for DVD menu.
5 Press the Arrow buttons (K/L) to select a
setting, then press the ENTER button.
¡If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to
enter the code for the desired language. (Refer to the
language code list below.)
¡Only the languages supported by the disc can be
selected.
6 Press the SETUP button to exit.
NOTE
¡Language Setting for Audio and Subtitle is not avail-
able with some discs. Then use the AUDIO and the
SUBTITLE buttons. Details are on page 42.
TO CHANGE THE ON-SCREEN MENUS
You can access the TV/VCR SETUP menu by pressing
the SETUP button from the DVD mode. Refer to
“Selecting the Language” on page 16 to changing the
on-screen menus.
¡In case of selecting from the DVD mode, you cannot
select “CHANNEL SET UP”, “V-CHIP SET UP”,
“CAPTION”, “TIME SEARCH”, or “INDEX
SEARCH” menus.
DVD-V
LANGUAGE
AUDIO ORIGINAL
SUBTITLE OFF
DISC MENU ENGLISH
QUICK SETUP
TV MODE
4:3 LETTER BOX
DOLBY DIGITAL ON
If you choose a Language that has a 3 letter language
code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 42. If
you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
Language Code
A-B
Abkhazian 4748
Afar 4747
Afrikaans 4752
Albanian 6563
Amharic 4759
Arabic 4764
Armenian 5471
Assamese 4765
Aymara 4771
Azerbaijani 4772
Bashkir 4847
Basque 5167
Bengali;Bangla 4860
Bhutani 5072
Bihari 4854
Bislama 4855
Breton 4864
Bulgarian 4853
Burmese 5971
Byelorussian 4851
C-E
Cambodian 5759
Catalan 4947
Chinese [CHI] 7254
Corsican 4961
Croatian 5464
Czech 4965
Danish [DAN] 5047
Dutch [DUT] 6058
English [ENG] 5160
Esperanto 5161
Estonian 5166
F-H
Faroese 5261
Fiji 5256
Finnish [FIN] 5255
French [FRE] 5264
Frisian 5271
Galician 5358
Georgian 5747
German [GER] 5051
Greek [GRE] 5158
Greenlandic 5758
Guarani 5360
Gujarati 5367
Hausa 5447
Hebrew 5569
Hindi 5455
Hungarian [HUN] 5467
I-K
Icelandic [ICE] 5565
Indonesian 5560
Interlingua 5547
Interlingue 5551
Inupiak 5557
Irish [IRI] 5347
Italian [ITA] 5566
Japanese [JPN] 5647
Javanese 5669
Kannada 5760
Kashmiri 5765
Kazakh 5757
Kinyarwanda 6469
Kirghiz 5771
Kirundi 6460
Korean [KOR] 5761
Kurdish 5767
Language Code
L-N
Laothian 5861
Latin 5847
Latvian;Lettish 5868
Lingala 5860
Lithuanian 5866
Macedonian 5957
Malagasy 5953
Malay 5965
Malayalam 5958
Maltese 5966
Maori 5955
Marathi 5964
Moldavian 5961
Mongolian 5960
Nauru 6047
Nepali 6051
Norwegian [NOR] 6061
O-R
Occitan 6149
Oriya 6164
Oromo(Afan) 6159
Panjabi 6247
Pashto;Pushto 6265
Persian 5247
Polish 6258
Portuguese [POR] 6266
Quechua 6367
Rhaeto-Romance 6459
Romanian [RUM] 6461
Russian [RUS] 6467
S
Samoan 6559
Sangho 6553
Sanskrit 6547
Scots Gaelic 5350
Serbian 6564
Serbo-Croatian 6554
Sesotho 6566
Setswana 6660
Shona 6560
Sindhi 6550
Singhalese 6555
Siswat 6565
Slovak 6557
Slovenian 6558
Somali 6561
Spanish [SPA] 5165
Sundanese 6567
Swahili 6569
Swedish [SWE] 6568
T
Tagalog 6658
Tajik 6653
Tamil 6647
Tatar 6666
Telugu 6651
Thai 6654
Tibetan 4861
Tigrinya 6655
Tonga 6661
Tsonga 6665
Turkish [TUR] 6664
Turkmen 6657
Twi 6669
U-Z
Ukrainian 6757
Urdu 6764
Uzbek 6772
Vietnamese 6855
Volapuk 6861
Welsh 4971
Wolof 6961
Xhosa 7054
Yiddish 5655
Yoruba 7161
Zulu 7267
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 44
–
45
–
EN
01A11
AUDIO SETTINGS
Choose the appropriate Audio settings for your equip-
ment as it only affect during the playback of DVD
discs.
1 Press the SETUP button twice in STOP mode
so that the DVD SETUP menu appears.
¡ If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
2 Press the Arrow button B to select CUS-
TOM, then press the ENTER button.
¡CUSTOM mode will appear.
3 Press the Arrow buttons (s/ B) to select
AUDIO, then press the ENTER button to
confirm.
4 Press the Arrow buttons (K/L) to select the
below items, then press the ENTER buttons.
DRC (Dynamic Range Control):
¡To compress the range of soft to loud sound.
¡The default setting is OFF.
DOLBY DIGITAL:
Set to On when the unit is connected to a Dolby Digital
Decoder.
(ON: Output a Dolby Digital signal)
(OFF: Convert the Dolby Digital to PCM (2 channel
stereo))
¡The default setting is ON.
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be acti-
vated and sound will be down sampled at 48kHz.
5 Press the SETUP button to exit.
QUICK
AUDIO
DRC OFF
DOLBY DIGITAL ON
DOWN SAMPLING ON
You can change certain aspects of the DVD display
screens and on-screen messages on the TV screen.
1 Press the SETUP button twice in STOP mode
so that the DVD SETUP menu appears.
¡ If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
2 Press the Arrow button B to select CUS-
TOM, then press the ENTER button.
¡CUSTOM mode will appear.
3 Press the Arrow button (s/B) to select DIS-
PLAY, then press the ENTER button to confirm.
4 Press the Arrow buttons (K/L) to select the
below items, then press the ENTER button.
TV MODE:
¡Press the Arrow buttons (K/L) for an item selection,
then press the ENTER button.
¡Select 4:3 LETTER BOX for a black bars appears
on top and bottom of the screen.
¡Select 4:3 PAN & SCAN for a full height picture
with both sides trimmed.
¡The default setting is 4:3 LETTER BOX.
ANGLE ICON:
¡Press the ENTER button repeatedly to turn Angle
icon ON or OFF.
¡The default setting is ON.
AUTO POWER OFF:
¡Press the ENTER button repeatedly to turn Auto
Power off ON or OFF.
¡The default setting is ON and it will turn the
TV/DVD/VCR to off automatically after 15 minutes
of no use.
5 Press the SETUP button to exit.
QUICK
DVD-V
DISPLAY SETTING
DISPLAY
TV MODE
4:3 LETTER BOX
ANGLE ICON ON
AUTO POWER OFF ON
QUICK SETUP
TV MODE
4:3 LETTER BOX
DOLBY DIGITAL ON
QUICK SETUP
TV MODE
4:3 LETTER BOX
DOLBY DIGITAL ON
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 45
–
46
–
EN
01A11
–
46
–
CONTROL LEVELS
¡
ALL
All parental lock is cancelled.
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
¡
Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
¡
Level 1
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
PARENTAL CONTROL
Parental Control limits the disc viewing that exceed
your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
DVD-V
PARENTAL LEVEL
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s rat-
ings exceed the level you set.
1 Press the SETUP button twice in STOP mode
so that the QUICK SETUP menu appears.
¡ If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
2 Press the Arrow button B to select CUS-
TOM, then press the ENTER button.
3 Press the Arrow buttons (s/B) to select
PARENTAL, then press the ENTER button.
4 Enter your four-digit password then press
the ENTER button.
5 Press the Arrow buttons (K/L) to select
PARENTAL LEVEL, then press the ENTER
button.
6 Press the Arrow buttons (K/L) to select
the desired level.
7 Press the SETUP button to exit
NOTES
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password.(in the event you forget the password, see
below)
¡To change the password, press the Arrow buttons
(K/L) to select CHANGE at step 5, then press the
ENTER button. Enter the four-digit pass-word, then
press the ENTER button.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
IF YOU FORGET THE PASSWORD
1 Press the number buttons 4, 7, 3, 7 at step 4.
Then enter your new password.
¡Password will be cleared and parental level will be
set to ALL.
2 Proceed the above Steps 5-7 again.
PARENTAL
PARENTAL LEVEL ALL
QUICK SETUP
TV MODE
4:3 LETTER BOX
DOLBY DIGITAL ON
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 46
–
47
–
EN
01A11
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked
possibilities. Before arranging for service, check these items. It could save your time and money.
TV/VCR Mode
TROUBLESHOOTING GUIDE
PROBLEM CORRECTIVE ACTION
No picture and sound.
•
Make sure the AC cord is connected to an AC outlet.
•
Check antenna connection.
•
Press the SELECT button on the remote control to select TV mode.
Then try other TV feature.
•
Let the TV/DVD/VCR program its tuner memory.
No picture or poor picture on
•
Adjust direction or replace antenna.
TV/DVD/VCR.
•
Adjust picture controls.
No sound or poor sound.
•
Adjust volume control on remote control or main unit.
•
Press the MUTE button to restore sound.
Bars On Screen
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
Picture Distorted or Blurred
•
Try a new channel, if OK, then possible station trouble.
•
If outside antenna is being used, check for broken wire.
Picture Rolls Vertically
•
Try a new channel, if OK, then possible station trouble.
Lines or Streaks in Picture
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
No Color
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Adjust COLOR control.
Poor Reception on Some Channels
•
Try a new channel, if OK, then possible station trouble.
Ghosts in Picture
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
Weak Picture
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Adjust CONTRAST & BRIGHT control.
Sound OK, Picture Poor
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Adjust CONTRAST & BRIGHT control.
If the TV/DVD/VCR does not perform properly when operated as instructed in this Owner’s Manual, check
the player, consulting the following checklist.
PROBLEM CORRECTIVE ACTION
No power.
•
Make sure the power plug is connected to an AC outlet.
•
Make sure the power is turned on.
The TV/DVD/VCR does not
•
Check if the power plug is connected to an AC outlet.
respond to the remote control.
•
Check the batteries in the remote control.
•
Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote.
•
You have to be within 23 feet of the TV/DVD/VCR.
•
Check if the correct mode is selected. If not switch the mode by
pressing the SELECT button on the remote control,whichever you need.
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 47
–
48
–
EN
01A11
CLOSED CAPTION PROBLEM POSSIBLE REMEDY
My TV/DVD/VCR is showing • You are watching a live broadcast and spelling errors made by the
captions that are misspelled. • closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/DVD/VCR will not show • Captions that are delayed a few seconds behind the actual
the text dialogue are common for live broadcast. Most captioning production
in its entirety or there is a delay of • companies can display a dialogue to a maximum of 220 words
what is being said. • per minute. If a dialogue exceeds that rate, selective editing is used
• to insure that the captions remain up-to-date with the current
• TV screen dialogue.
My captions are scrambled with • Interference caused by building, power lines, thunderstorms, etc.
white boxes on the TV screen. • may cause scrambled or incomplete captions to appear.
My program guide listed a TV show
• Broadcasters may at times use a time compression process to speed
as being closed captioned but none • up the actual program so that additional advertising time can be
of the captions were displayed. • given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not
• The video tape was either an illegal copy or the tape duplicating
show any captions. The tape box • company accidentally left out the captioning signals during the
mentions it being closed captioned. • copying process.
My TV screen shows a black box • You are in the TEXT mode. Select CAPTION mode to CAPTION
on certain channels. • [OFF].
PROBLEM CORRECTIVE ACTION
Picture OK, Sound Poor
•
Try a new channel, if OK, then possible station trouble.
•
Check for local interference.
Timer recording is not possible.
•
Make sure the timer recording is set correctly.
•
Make sure the power is off.
•
Make sure the TV/DVD/VCR clock is set correctly.
Cannot go into Record mode.
•
Make sure the tape has an erase-prevention tab. If need, cover the
•
hole with plastic tape.
Playback picture is partially noisy. • Adjust tracking control for a better picture using the CHANNEL
• button K or L on the TV/DVD/VCR.
No picture but the audio is OK in • Head cleaning may be necessary. Refer to “AUTO HEAD
playback. • CLEANING” on page 50.
No operation by infrared Remote • Make sure the AC cord is connected to an AC outlet.
Control. • Check batteries in remote control.
Video or color fades in and out • You can not copy a copyrighted video tape. You are experiencing
when making a copy of a video tape
. • copy guard protection.
Different color marks on screen.
•
Magnetism from nearby appliances and geomagnetism might affect
the color of the TV picture. Move the
TV/DVD/VCR
away from the
appliances, the
TV/DVD/VCR
can repair itself automatically. If you
want to repair immediately,
turn off using the POWER button, then
turn it on again 30 minutes or so later (27” model), or unplug the
power cord, then plug it in again 30 minutes or so later (19” model).
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 48
–
49
–
EN
01A11
NOTES:
•
Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
•
Playback from a desired track and random playback are not available during program playback.
PROBLEM CORRECTIVE ACTION
No picture. • Connect the video cables firmly.
• Insert a correct video disc that plays on this TV/DVD/VCR.
• Press the SELECT button on the remote control to select DVD mode.
Then, try other DVD feature.
Disc cannot be played
. • Insert the disc.
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
No sound
. • Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
No DTS audio is output
. • This TV/DVD/VCR does not support DTS audio. This is not a mal-
function.
Distorted picture
. • There are some cases where pictures may be slightly distorted, which
are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language •
The selected language is not available for audio or subtitles on the DVD.
does not match the set up
This is not a malfunction
The camera angle cannot be changed •
The DVD does not
contain sequences recorded from different camera
angles.
This is not a malfunction
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected
changed language.
This is not a malfunction.
“Prohibited icon” appears on the • That operation is prohibited by the player or the disc.
screen, prohibiting an operation
This is not a malfunction.
CD sound dropout • Scratched disc. Replace the disc with unscratched one.
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
DVD Mode
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 49
–
50
–
EN
01A11
EN
01A11
CABINET CLEANING
•
Wipe the front panel and other exterior surfaces of
the TV/DVD/VCR with a soft cloth immersed in
lukewarm water and wrung dry.
•
Never use a solvent or alcohol. Do not spray insec-
ticide liquid near the TV/DVD/VCR. Such chemi-
cals may cause damage and discoloration to the
exposed surfaces.
AUTO HEAD CLEANING
•
Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
•
Playback picture may become blurred of interrupt-
ed while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use, or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during play-
back, the video heads in your TV/DVD/VCR may
need to be cleaned.
1.Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2.If a Video Head Cleaner does not solve the prob-
lem, please call our help line at 1-800-968-3429, to
locate an Authorized Service Center.
NOTES:
•
Remember to read the instructions included with
the video head cleaner before use.
•
Clean video heads only when problems occur.
SERVICING
•
Should your TV/DVD/VCR become inoperative,
do not try to correct the problem by yourself. There
are no user-serviceable parts inside. Turn off,
unplug the power cord, and please call our help
line at 1-800-968-3429, to locate an Authorized
Service Center.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
•
If the player still does not perform properly when it is operated while referring to the relevant sections and to
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult
your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
•
Use discs which have the following logos on them.
(Optical audio digital discs.)
•
Handle the discs so that fingerprints and dust do
not adhere to the surfaces of the discs.
•
Always store the disc in its protective case when it
is not used.
DISC HANDLING
•
To clean-off, use a soft cloth.
•
Do not use a hard cloth since this will mar the disc.
•
Wipe the disc in a straight line from center to edge.
•
Never wipe with a circular motion.
•
Do not use detergent or abrasive cleaning agents.
MAINTENANCE
Recordable
ReWritable
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 50
–
51
–
EN
01A11
CRT
[19 inch model]: 19 inch in-line gun, 90˚
deflection tube
[27 inch model]: 27 inch in-line gun, 110˚
deflection tube
Television system : NTSC-M
Closed caption system :§15.119/FCC
Video Heads : Rotary four-head
Tape width : 1/2 inch
Tape speed
SP : 33.40mm/sec.
LP : 16.67mm/sec.
SLP : 11.12mm/sec.
Tuner channel
TV VHF Low : #2~#6
TV VHF High : #7~#13
TV UHF : #14~#69
CATV
VHF : 5A
MID band : A5~A1, A~I
SUPER band : J~W
HYPER band : W+1~W+84
Product type: DVD Player
Discs: DVD video, Audio CD
Output signal format: NTSC color
Frequency response
(out put jack)
DVD (linear sound): 20 Hz to 22 kHz
(sample rate: 48 kHz)
20 Hz to 44 kHz
(sample rate: 96 kHz)
CD: 20 Hz to 20 kHz
Signal-to-noise ratio
(S/N ratio)(out put jack)
CD: 75 dB (EIAJ)
Dynamic range
(out put jack)
DVD (linear sound): 85 dB
CD: 84 dB (EIAJ)
Total distortion factor
CD: 0.07% (EIAJ)
Wow and flutter: Below the measurement
limitation (+/-0.001%
W PEAK) (EIAJ)
•
Designs and specifications are subject to change without notice.
•
If there is a discrepancy between languages, the default language will be English.
TV/VCR
DVD
GENERAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS
Sound output: 2 speakers, 1W, 8 ohm
OTHER SPECIFICATIONS
Terminals
Antenna input: VHF/UHF/CATV
75 ohm unbalanced (F-type)
Video input: RCA connector [ 1
Audio L/R input: RCA connector
[ 2
Headphone: 1/8” stereo (3.5 mm)
Coaxial digital
audio output: One pin jack,
500m Vpp (75 ohm)
Analog audio L/R
output : RCA connector [ 2
Remote control: Digital encoded
infrared light system
Operating
temperature: 5ºC to 40ºC
(41ºF~104ºF)
Power requirements: AC 120V, 60Hz
[19 inch model]
Power consumption
(Maximum): 90W
Picture tube: 19"
Dimensions: H:19-11/16” (500mm)
W:21-7/8” (556mm)
D:18-3/4” (476.5mm)
Weight: 45.2 lbs (20.5kg)
[27 inch model]
Power consumption
(Maximum): 125W
Picture tube: 27"
Dimensions: H:25-1/2” (648mm)
W:26-9/16” (675mm)
D:19-11/16” (500mm)
Weight: 86 lbs (39.0kg)
SPECIFICATIONS
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 51
–
52
–
ES
0C28
INDICE
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 52
MANDO A DISTANCIA . . . . . . . . . . . . . . . . . . . . . . . . . 52
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54
MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54
CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54
CONEXIÓN A UN AMPLIFICADOR ESTÉREO
EQUIPADO CON TOMAS DE ENTRADA DIGITAL,
PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 54
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SECCIÓN DE TV/VCR
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54
PREAJUSTE DE CANALES. . . . . . . . . . . . . . . . . . . . . . 55
CÓMO BORRAR (AGREGAR) CANALES . . . . . . . . . . 55
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55
CONTROLES DE
OPERACIÓN Y FUNCIONES
PANEL FRONTAL DEL
TELEVISOR/DVD
Consulte la figura 1 de la página 9
MANDO A DISTANCIA
Consulte la figura 2 de la página 9
VISTA POSTERIOR
Consulte la figura 3 de la página 10
1. Botón POWER
Presione este botón para conectar y desconectar la ali-
mentación.
2. Botones VOLUME X/Y
Presione estos botones para controlar el nivel de volumen
del DVD y el televisor.
3. Botones SKIP (para DVD)
Presione el botón correspondiente una vez para omitir
capítulos o pistas y desplazarse a un punto específico.
Mantenga el botón presionado para cambiar la veloci-
dad de reproducción en avance o retroceso.
4. Botón PLAY
Inicia la reproducción del contenido del disco o cinta.
5. Botón STOP
Detiene la reproducción del disco.
6. Botón OPEN/CLOSE
Presione este botón para insertar discos en la bandeja o
retirarlos de ella.
7. Bandeja de carga del disco
8. Indicador DVD
Se ilumina durante el modo DVD.
9. Botón SELECT
Presione este botón para cambiar al modo TV/VCR,
modo de entrada externa o modo de DVD.
10. Indicador TV/VCR
Se ilumina durante el modo TV/VCR.
11. Botones CHANNEL K/L
Utilice estos botones para seleccionar canales memorizados.
12. Indicador de grabación
Parpadea durante la grabación. Se ilumina durante el
modo de espera de grabación controlada por temporizador.
13. Botón REC/OTR (RECORD)
Presione este botón para grabar manualmente. Este
botón también activa la función de grabación instan-
tánea (OTR). (La función OTR sólo está disponible
durante el modo TV/VCR.)
14. Botón REW (para TV/VCR)
Presione este botón para rebobinar la cinta o para ver
la imagen rápidamente en dirección de retroceso
durante el modo de reproducción. (Búsqueda en direc-
ción de retroceso)
15. Botón FWD (para TV/VCR)
Presione este botón para adelantar rápidamente la cinta
o para ver la imagen rápidamente en dirección de
avance durante el modo de reproducción. (Búsqueda en
dirección de avance)
16. Botón STOP/EJECT
Presione este botón para detener la cinta. Presiónelo en
el modo de parada para retirar la cinta del
televisor/DVD/videograbadora.
17. Ventanilla del sensor de mando a distancia
18. Toma HEADPHONE
Para conectar auriculares (no suministrados) y escuchar
en privado.
19. Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una
videocámara o de una videograbadora.
20. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
21. Compartimiento del cassette
22. Botón PICTURE
Presione este botón para ajustar la imagen.
23. Botones numéricos
Modo TV:
Presione dos botones para acceder directamente al
canal deseado.
No olvide presionar “0” antes de elegir un canal de un
solo dígito.
Botón +100
Presione este botón para seleccionar canales de tele-
visión por cable cuyo número sea igual o superior a 100.
Modo DVD:
Presione este botón para introducir el número deseado.
Botón +10
Presione este botón para introducir números
iguales o
mayores que 10
.
24. Botón PAUSE
Hace una pausa en la reproducción del disco o cinta.
25. Botón SPEED
Presione este botón para seleccionar la velocidad de
grabación deseada: SP/SLP.
26. Botón C.RESET
Presione este botón para poner el contador en 0:00:00.
Presiónelo también para cancelar un ajuste de progra-
ma de temporizador.
27. Botón DISPLAY
Modo TV/VCR:
Para visualizar el contador o el número del canal y la
fecha actual en la pantalla del televisor.
Modo DVD:
Indica el estado actual en la pantalla del televisor para
fines de comprobación.
28. Botón SETUP
Presione este botón para activar o salir del modo de
menús de televisor o configuración de DVD.
29. Botón TITLE
Para visualizar el menú de títulos.
TD851/951ES.QX33 03.3.1 1:57 PM Page 52
–
53
–
ES
0C28
30. Botón CLEAR
Para cancelar ajustes.
31. Botón MODE
Activa el modo de reproducción programada o el modo de
reproducción aleatoria.
32. Botón SEARCH MODE
Presione este botón para localizar un punto deseado.
33. Botón AUDIO
Presione este botón para seleccionar un idioma de
audio o el modo de sonido deseado.
34. Botón SUBTITLE
Presione este botón para seleccionar el idioma de subtí-
tulos deseado.
35. Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
36. Botón ANGLE (modo DVD)
Presione este botón para cambiar el ángulo de la cámara
y ver la secuencia que se está reproduciendo desde un
ángulo diferente.
37. Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
38. Botón RETURN
Permite volver a la operación anterior en el modo de
configuración de DVD.
39. Botón ENTER
Presione este botón para establecer un ajuste.
40. Botones de flechas
Modo TV/VCR:
Presione estos botones para seleccionar un modo de
ajuste en el menú que aparece en la pantalla del televisor.
Presiónelos también para seleccionar opciones o
establecer ajustes en un menú en particular.
Modo DVD:
Use estos botones para hacer ajustes mientras observa
la imagen en la pantalla del televisor.
41. Botón DISC MENU
Muestra los menús contenidos en el DVD.
42. Botón ZOOM
Amplía parte de la imagen reproducida de un DVD.
43. Botón MUTE
Suprime la salida de sonido. Presiónelo de nuevo para
restablecer el sonido.
44. Botón SLEEP
Utilice este botón para ajustar el temporizador de dormir.
45. Botón SELECT
Presione este botón para cambiar entre los modos
TV/VCR y DVD. El modo seleccionado (TV/VCR o
DVD) se visualiza en el indicador del panel delantero.
46. Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por cable
o sistema de satélite.
47. Cable de alimentación
Conéctelo a una toma de CA estándar (120 V, /60 Hz).
NOTA: Antes de conectar el cable de alimentación a
una toma de CA estándar, retírelo del gancho
para evitar dañarlo.
48. Toma de salida de audio digital COAXIAL
Conéctela solamente a la entrada digital de un amplifi-
cador externo o decodificador de audio de DVD.
49. Toma de salida AUDIO L/R
Conéctela a la entrada de audio analógico de un ampli-
ficador o decodificador externo.
PREPARACIÓN PARA LA
UTILIZACIÓN
CONEXIONES DE ANTENA/CABLE
ANTENAS SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena
exterior.
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a su televisor/DVD/
videograbadora, sin una caja de convertidor.
Con esta conexión podrá:
1) Utilizar el mando a distancia del televisor/DVD/
videograbadora para seleccionar canales.
2) Programar uno o más canales decodificados para
grabación automática controlada por temporizador.
NOTA: Este televisor/DVD/videograbadora SÓLO
puede grabar el canal que se está viendo.
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
Si su compañía de televisión por cable le suministra
una caja de convertidor o si utiliza un sistema de
satélite, podrá utilizar la conexión básica que se
muestra en la ilustración.
Al utilizar esta conexión, también podrá grabar canales
codificados. Sin embargo, la selección de los canales
deberá hacerse con la caja de convertidor o con la caja
de satélite. Esto significa que no es posible cambiar de
canal utilizando el mando a distancia del televisor/DVD/
videograbadora. La grabación en ausencia (controlada
por temporizador) está limitada a un canal a la vez.
PARA GRABAR UN CANAL
CODIFICADO/DECODIFICADO
1.Ajuste el selector de canales del
televisor/DVD/videograbadora al canal de salida de
la caja de convertidor de televisión por cable o caja
de satélite. (Ej., CH3)
2.
Seleccione el canal que desea grabar en la caja de
convertidor de televisión por cable o caja de satélite.
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención
del instalador de sistemas CATV para que tenga
en cuenta el Artículo 820-40 de la NEC, que pro-
porciona recomendaciones para hacer una conex-
ión a tierra apropiada y, en particular, especifica
que la tierra del cable debe conectarse al sistema
de puesta a tierra del edificio, tan cerca del punto
de entrada del cable como sea posible.
Consulte la figura 4 de la página 11
CONEXIÓN A TOMAS DE
ENTRADA EXTERNA
Cuando vea un programa grabado en otra fuente (videograbado-
ra o videocámara), utilice las tomas de entrada de audio/vídeo
de la parte delantera del televisor/DVD/videograbadora.
Conecte las tomas de salida de audio/vídeo de otra fuente a
las tomas AUDIO L/R y VIDEO de este
televisor/DVD/videograbadora. Luego, presione los botones
CHANNEL K/L hasta que aparezca "AUX" en la pantalla.
NOTA:
•
Cuando conecte una videograbadora monofónica (otra
fuente) a este televisor/DVD/videograbadora, conecte la
toma de salida de audio de la videograbadora monofónica
(otra fuente) a la toma AUDIO L de este
televisor/DVD/videograbadora. El audio saldrá igual-
mente por los canales izquierdo y derecho.
Consulte la figura 5 de la página 12
TD851/951ES.QX33 03.3.1 1:57 PM Page 53
SECCIÓN DE TV/VCR
–
54
–
ES
0C28
MODO DE ENTRADA EXTERNA
Al usar una señal de entrada externa (otra videograbado-
ra o una videocámara), conecte los cables de salida de
audio/vídeo del equipo externo a las tomas AUDIO L/R
IN/ VIDEO IN de su televisor/DVD/videograbadora.
Luego, presione los botones CHANNEL K/L hasta que
aparezca "AUX" en la pantalla.
CONEXIÓN A UN DECODIFICADOR
DOLBY DIGITAL (para DVD)
Si utiliza este televisor/DVD/videograbadora para
reproducir un disco DVD grabado en formato de
sonido envolvente Dolby Digital de 5,1 canales, el
televisor/DVD/videograbadora emitirá un flujo de
datos DOLBY DIGITAL desde su toma de salida de
audio digital COAXIAL. Si conecta el reproductor a
un decodificador Dolby Digital, podrá disfrutar de
una tonalidad más convincente y real, con un sonido
envolvente potente y de alta calidad similar al de los
cines.
Utilice cables digitales coaxiales de audio
disponibles en el comercio especializado para hacer
las conexiones de audio.
NOTAS:
•
Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
•
Consulte los manuales de instrucciones de los
componentes que va a conectar al
televisor/DVD/videograbadora.
•
Si conecta un decodificador Dolby Digital, ajuste
la función DOLBY DIGITAL a ON para salida de
audio en el modo de configuración.
•
A menos que se haga la conexión a un decodifi-
cador Dolby Digital, ajuste la función Dolby
Digital a OFF para salida de audio en el modo de
configuración. La reproducción en un
televisor/DVD/videograbadora utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede causar daños a los altavoces.
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D
doble son marcas de fábrica de Dolby
Laboratories.
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a distancia en el
sentido de la flecha.
2) Inserte 2 pilas "AA" en el compartimiento de las
pilas, en el sentido indicado por las marcas de
polaridad (+/-).
3) Vuelva a poner la cubierta.
PARA INSERTAR LAS PILAS
CONEXIÓN A UN SISTEMA
ESTÉREO
NOTAS:
•
Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
•
Consulte el manual de instrucciones de su sistema
estéreo y de cualquier otro componente que vaya a
conectar al televisor/DVD/videograbadora.
CONEXIÓN AUN AMPLIFICADOR
ESTÉREO EQUIPADO CON TOMAS
DE ENTRADA DIGITAL, PLATINA
MD O PLATINA DAT (Para DVD)
Utilice un cable digital coaxial de audio de venta en el
comercio especializado para hacer las conexiones de audio.
Conexión a un amplificador equipado con tomas de
entrada digital, platina MD o platina DAT.
NOTAS:
•
La fuente de audio de un disco grabado en formato
de sonido envolvente Dolby Digital de 5,1 canales
no se puede grabar como sonido digital mediante
una platina MD o DAT.
•
Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
•
Consulte los manuales de instrucciones de los
componentes que va a conectar al
televisor/DVD/videograbadora.
•
Ajuste la función Dolby Digital a OFF para salida
de audio en el modo de configuración. La repro-
ducción en un televisor/DVD/videograbadora uti-
lizando ajustes incorrectos puede generar ruido y
distorsión, y también puede causar daños a los
altavoces.
PREPARACIÓN PARA LA
UTILIZACIÓN
Puede programar el sintonizador para explorar todos
los canales que pueda recibir en su zona.
NOTA: La programación de la memoria de canales
NO es necesaria cuando se hace la conexión a una
caja de televisión por cable o a una caja de satélite.
Simplemente ajuste el selector de canales del televi-
sor/DVD/videograbadora a la posición correspondi-
ente al canal de salida de la caja de televisión por
cable o caja de satélite (ej., CH3). Luego, seleccione
el canal que desea ver en la caja de televisión por
cable o en la caja de satélite.
Consulte la figura 6 de la página 13
Consulte la figura 7 de la página 13
Consulte la figura 8 de la página 14
TD851/951ES.QX33 03.3.1 1:57 PM Page 54
–
55
–
ES
0C28
CÓMO BORRAR (AGREGAR)
CANALES
2 Seleccione “AGREGAR/BORRAR”
Presione el botón de flecha K o L para señalar
“AGREGAR/BORRAR”.
Presione el botón ENTER.
3 Introduzca el número del canal deseado
Presione el botón de flecha K o L hasta que aparez-
ca el número del canal deseado. (También puede uti-
lizar también los botones numéricos o los botones
CHANNEL K/L para introducirlo.) (Ejemplo: CH8)
4 Borre el canal de la memoria o agréguelo a
ella
Presione el botón ENTER. El número del canal
seleccionado se ilumina de color rojo. El canal de
borra de la memoria.
•
Para borrar otro canal, repita los pasos [3] y [4].
•
Si vuelve a presionar el botón ENTER, el canal se
memorizará de nuevo.
•
Presione el botón RETURN para hacer que el tele-
visor/videograbadora vuelva al menú SETUP.
5 Salga del modo de preajuste de canales
Presione el botón SETUP del mando a distancia para
volver al modo de televisor.
NOTA: Para confirmar que los canales han sido bor-
rados o agregados, presione el botón CHANNEL K o
L.
Canal agregado: Se enciende en azul.
Canal borrado: Se enciende en rojo.
Puede borrar de la memoria los canales que ya no
recibe o que ve muy raramente. (Por supuesto, puede
volver a agregar a la memoria los canales que haya
borrado de la misma.)
1 Seleccione “AJUSTE DE CANAL”
Presione el botón SETUP del mando a distancia.
Presione el botón de flecha K o L para señalar
“AJUSTE DE CANAL”.
Luego, presione el botón ENTER.
TV/VCR
PREAJUSTE DE CANALES
1 Conecte el cable de alimentación del televi-
sor/DVD/videograbadora
Conecte el cable de alimentación del
televisor/DVD/videograbadora
NOTA:
•
Si aparecen algunos dígitos en la esquina de la pan-
talla, presione el botón POWER sin desconectar el
cable de alimentación.
2 Encienda el televisor/DVD/videograbadora
Presione el botón POWER para encender el televi-
sor/DVD/videograbadora.
3 Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS”
Presione el botón ENTER para seleccionar "ENG-
LISH" = inglés, "ESPAÑOL" o "FRANÇAIS" =
francés. "[ ]" indica el idioma seleccionado.
4 Inicie el preajuste automático
Presione el botón de flecha K o L para señalar
"AUTOPRESELECCION".
Luego, presione el botón ENTER.
El sintonizador explora y memoriza todos los canales
activos de su zona.
NOTAS:
•
El televisor/DVD/videograbadora distingue entre
los canales de TV estándar y los canales de tele-
visión por cable.
•
Si desea reproducir o grabar una cinta de vídeo
ANTES de preajustar el sintonizador, deberá pre-
sionar el botón SETUP del mando a distancia.
•
El televisor/DVD/videograbadora puede memorizar
canales de TV como canales de CATV si las condi-
ciones de recepción no son buenas. Si esto sucede,
vuelva a intentar la acción AUTO MEMO cuando
las condiciones de recepción mejoren.
5 Una vez finalizada la exploración
El sintonizador se detiene en el canal memorizado
más bajo. Si desea recuperar los canales selecciona-
dos, podrá seleccionar los canales directamente con
los botones numéricos o los botones CHANNEL K o
L del mando a distancia.
TV/VCR
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA
Para empezar
¡Conecte la alimentación del amplificador y otros
componentes, si es necesario.
1 Presione el botón POWER.
¡La alimentación se conectará.
2 Presione el botón OPEN/CLOSE para abrir
la bandeja de carga del disco.
3 Ponga el disco deseado en la bandeja, con
la etiqueta hacia arriba.
4 Presione el botón PLAY.
¡La bandeja se cerrará automáticamente y la repro-
ducción comenzará desde el primer capítulo o pista
del disco. Si la reproducción no comienza automáti-
camente, presione el botón PLAY.
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú podrá aparecer en la pan-
talla.
5 Presione el botón STOP para detener la
reproducción.
CD
DVD-V
TD851/951ES.QX33 03.3.1 1:57 PM Page 55
Printed in Malaysia 0EMN02116
TD851UB/TD951UB ★★★★★
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to
any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,
please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-968-3429
http://www.funai-corp.com
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
TD851/951(P36-52).QX33 03.3.1 1:56 PM Page 52
1 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sylvania 6719DD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sylvania 6719DD in de taal/talen: Engels als bijlage per email.

De handleiding is 1,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info