650844
27
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
Dismantling the
device
27
Characteristic Possible cause Remedy
The roller shutter blocks on raising or lowering. The roller shutter slats have become displaced. Make sure that all slats are horizontal.
Lubricate sluggish areas with wax.
In order to pull the roller shutter free, briefly switch the drive
on in the opposite direction.
The roller shutter scrapes in the roller shutter
box due to a lack of pressure rollers on the
window frame.
Open the roller shutter box.
Install the pressure rollers.
The roller shutter has been rolled up at a slant
as the device has not been installed horizontally.
Make sure that the device is disconnected from the mains
power supply.
Remove the device.
Information on removing the device can be found in the
chapter entitled Dismantling the device from page 27.
Install the device horizontally again.
Information on this can be found as of the section entitled
Installing the bearings from page 19.
Insulating material has come loose in the roller
shutter box and is blocking the roller shutter.
Open the roller shutter box.
Remove the insulating material.
Contact the manufacturer as regards professional insulation
of the roller shutter box.
The roller shutter is too light. Make sure that all slats are horizontal.
Weight the roller shutter e.g. with an appropriate piece of flat
iron.
Push the piece of flat iron into the bottom slat.
In order to pull the roller shutter free, briefly switch the drive
on in the opposite direction.
Dismantling the device
Proceed as follows to remove the tubular motor:
¾ Operate the motor to lower the roller shutter, until the roller shutter is no longer
hanging by the springs and these can be easily released from the winding shaft.
DANGER
Fatal electric shock due to coming into contact with live
components.
¾ Do not carry out any connection work on the device when it is
connected to the current supply.
¾ Make sure that the device is disconnected from the mains power
supply.
¾ Disconnect the cable from the current supply.
¾ Release the securing springs from the winding shaft.
¾ Pull the cotter pin out from the securing hole in the drive bearing's axle pin.
¾ Loosen the screws with which the roller capsule and the winding shaft are
screwed together.
¾ Slide the roller capsule up to the limit stop in the winding shaft.
¾ Pull the device out of the bearings.
¾ Pull the tubular motor out of the winding shaft.
Disposing of the device
The environmentally friendly disposal of operating material, electronic assemblies,
recyclable materials and other parts of the device is regulated by national and
regional laws.
¾ Contact the responsible local authority to obtain precise information on
disposal.
¾ Dispose of the device according to the legal regulations via a specialist disposal
company.
¾ Dispose of electronic components according to the legal regulations in
accordance with the German Electrical and Electronic Equipment Act
(ElektroG).
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Superrollo RM10MSF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Superrollo RM10MSF in de taal/talen: Duits, Engels, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 4,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info