Handleiding Sunwave src 3000 (pagina 41 van 41) (Engels)

122462

Verklein

Vergroot

Pagina terug

1/41

Pagina verder

SRC-3000

Touch Screen Remote Control

User’s Manual

030821

Preface

About this manual

This manual is designed to make using the SRC-3000 Touch

Screen Remote Control as easy as possible. Information in

this document has been carefully checked for accuracy;

however, no guarantee is given to the correctness of the

contents. The information in this document is subject to

change without notice.

This document contains proprietary information protected

by copyright. All rights are reserved. No part of this manual

may be reproduced by any mechanical, electronic or

other means, in any form, without the prior written

permission of Sunwave Technology Corporation.

Trademarks

All trademarks and registered trademarks are the property

of their respective owners.

SUNWAVE Customer Service & Support Info

E-Mail: info@sun-wave.com

URL: www.sun-wave.com

SRC-3000 User’s Manual

Table of Contents

Chapter 1 Introducing the SRC-3000 ................4

SRC-3000 Features ....................................................................... 5

Unpacking the SRC-3000 ............................................................ 5

Identifying Components ............................................................. 6

Chapter 2 Getting Started .................................7

Installing Batteries......................................................................... 7

Battery Indicator .................................................................. 7

Battery Tips and Precautions.............................................. 8

About the Touch Screen............................................................. 9

Turning the Touch Screen On............................................. 9

Touch Screen Precautions.................................................. 9

Using the Touch Screen Soft Keys.................................... 10

Accessing Setup................................................................. 10

Chapter 3 Setting Up the SRC-3000................12

LCD Layout: Device Keys.......................................................... 12

Code and Learn Setting Key.................................................... 14

Using Pre-programmed Code to Program Devices ............. 15

Using Code Learning Mode ..................................................... 18

Before Using Learning Mode............................................ 18

Learning from Another Remote Control ........................ 19

Erasing Key Codes and Device Codes (Delete) .......... 21

SRC-3000 Features

Using Macros .............................................................................. 22

Creating a New Macro .................................................... 22

Resetting the SRC-3000 to Factory Defaults .......................... 24

Chapter 4 Miscellaneous Settings..................25

Using the Transmission Feature ................................................ 25

Setting the Backlight Mode...................................................... 27

Set Backlight On Mode..................................................... 27

Set Backlight Sensor Sensitivity......................................... 28

Setting the Beep Signal............................................................. 29

Chapter 5 Controlling Devices .......................30

Alternating Touch Screen Pages............................................. 30

Viewing the Macro Key ............................................................ 30

Macro Interruption..................................................................... 31

Controlling Devices ................................................................... 32

Appendix A Functions and Specifications ..33

Functions ..................................................................................... 33

Specifications ............................................................................. 34

Appendix B Accessories ...............................35

Appendix C Troubleshooting........................36

Troubleshooting Tables ............................................................. 36

SRC-3000 User’s Manual

Chapter 1 Introducing the SRC-3000

Congratulations on your purchase of the SRC-3000 Touch

Screen Remote Control. The SRC-3000 is a digital universal

remote control that is easy to use, enabling you to control

all of your electronic devices equipped with an infrared (IR)

remote.

The SRC-3000 uses a user-friendly Touch Screen panel. You

can control up to eight devices, including VCRs, DVDs, TVs,

and satellite dishes.

The SRC-3000 enables you to quickly configure each device

in your household or office using the innovative “learning

eye” feature. In addition, the advanced macro function

enables you to initiate a chain of up to 60 commands with

the touch of a single key.

Convenient and easy to use, the SRC-3000 provides you

with a complete central control solution.

NOTE: This manual helps you learn how to use the

advanced features of the SRC-3000. It does not explain how

to use the functions for your devices. Please refer to your

device user’s manual for information related to your device.

SRC-3000 Features

The following list identifies the SRC-3000’s key features.

• Large Touch Screen display

• Macro sequence function—each macro can store 60

commands

• Eight device controls, including DVDs, TVs, Satellite

Receivers, VCRs, and CDs

• IR code learning from your existing remote controls to

quickly set up devices

• Pre-programmed manufacturer’s codes for many

models

• User programmable keys for each device, up to 56

keys in total

• Automatic Power Saving mode turns off the remote

after 90 seconds of inactivity

Unpacking the SRC-3000

After you have unpacked the SRC-3000, check the

contents to make sure the following items are included.

• SRC-3000

• User’s Manual

• Pre-programmed Code List

If any of the above items are missing or appear damaged,

contact your dealer immediately. Do not throw the

shipping carton away in case you need to ship your

SRC-3000.

SRC-3000 User’s Manual

Identifying Components

Refer to the following illustration to identify the components

of the SRC-3000.

Infrared Eye

Point the infrared eye at

the device you want to

operate.

Light Sensor

Detects ambient light to

automatically set the LCD

panel backlight.

LCD Touch Screen

The soft keys enable you to

change settings, configure

the SRC-3000, create

macros, and more.

Backlight

The SRC-3000 is equipped

with a blue backlight that

lights up for a preset

period, according to the

ambient lighting conditions.

Device keys

Press these keys to display

layout screens for the

devices listed.

Learning Eye

Point your device’s remote

control at the learning eye

to enable the SRC-3000 to

learn your device’s infrared

codes.

Figure 1: Front View

Infrared Eye

Light Sensor

LCD Touch

Screen

Backlight

Device Keys

Learning Eye

Chapter 2 Getting Started

This chapter provides you with the information to quickly

start using the SRC-3000.

Installing Batteries

The SRC-3000 operates on three AAA alkaline batteries (not

included). Batteries must be inserted before you can

operate the SRC-3000.

1. Turn the remote over, push the tab in the direction of

the arrow on the battery cover and lift the cover off.

2. Insert the batteries, matching the batteries to the (+)

and (–) marks inside the battery case.

3. Snap the battery cover back into place.

Battery Indicator

A battery icon is displayed in the upper left-hand corner

above the System Setup Key:

Battery low icon

Figure 2: The Battery Low Icon

When the batteries are almost depleted, the battery low

icon appears.

Installing Batteries

Battery Tips and Precautions

• Pay attention to the batteries when the battery half full

icon appears and replace batteries if needed.

• The SRC-3000 will not lose programmed data when

batteries are replaced.

• Always use fresh batteries. Alkaline batteries are

recommended. Do not mix different types of batteries.

• Be sure that the positive (+) and negative (–) polarities

of the batteries match the diagram shown in the

compartment.

• Do not expose the batteries to excessive heat or

flame.

• Keep batteries out of the reach of children.

• Weak batteries reduce the effective distance of the

unit.

• To reduce danger of leakage and damage, remove

batteries that have been used for more than two

years.

About the Touch Screen

The Touch Screen changes the number of soft keys

according to the device that is selected.

Turning the Touch Screen On

Turn on the SRC-3000 by touching the screen. The SRC-3000

turns itself off after 90 seconds.

Touch Screen Precautions

Please read the following instructions carefully.

• Tap the LCD Touch Screen gently. Never use force.

• Do not use a pen or any sharp object to tap the

screen, because you might damage the surface.

• Keep the Touch Screen dry. Wipe off any spills

immediately. The SRC-3000 is not waterproof. Never

immerse it in liquid.

• Don’t expose the SRC-3000 to extreme temperatures.

Keep it away from heat sources.

• Avoid dropping the SRC-3000.

• Don’t drop anything on the Touch Screen.

• Clean the LCD Touch Screen with a soft cloth. If

needed, dampen the cloth slightly before cleaning.

Never use abrasives or cleaning solutions.

SRC-3000 User’s Manual

Using the Touch Screen Soft Keys

The Touch Screen Soft Keys enable you to operate the SRC-

3000 and your external devices. Use these keys to program

codes from your existing remotes, control your devices, and

set up command sequences called macros. You will hear a

beep when you press a key. To turn the beep off and on,

see on page 29. The SRC-3000 turns itself off after 90

seconds.

Accessing Setup

The following table provides an

overview of major key functions. To

enter setup mode, press a function

key for three seconds; a confirmation

screen appears. Confirm setup mode

entry by pressing the four number keys

that appear (in any order) and then

selecting the desired setup mode.

About the Touch Screen

Name &

Key Icon

Function Setup Description

Device keys

Device setting

and LCD

layout

Key: Enter device setting and

arrange the LCD touch screen layout

to correspond to your remote control.

Refer to page 12.

You can also toggle device pages by

pressing the key again.

Bank: Arrange the device key

icon.(refer to page 13)

Code Setup key

Setup device

code

manually,

automatically,

or by code

learning

Code: Enables you to enter

preprogrammed code. Refer to

page 14.

Learn: Enables the remote to learn

codes from other remote controls.

Refer to page 14.

Macro key

Setup macro

Enables you to set Macro function.

Refer to page 22.

You can also view the macro setting

by pressing and holding the key.

Delete key

Delete and

reset to

default

Key: Erase key codes. Refer to page

21.

Bank: Erase device codes. Refer to

page 21.

Key & Bank: Reset to factory default.

Refer to page 24.

System setup key

Transmission,

backlight and

beep setup

Backlit: Setup backlighting period

and level. Refer to page 27.

Code: Transmit all data. Refer to

page 25.

Beep icon: Turns the beep sound

on/off. Refer to page 29.

After each setting, press the System

setup key to confirm your selection or

modification.

Figure 3: Major Function Keys

The following chapters describe each function in detail.

Chapter 3 Setting Up the SRC-3000

Before the SRC-3000 can be used to control a device, it

needs to be configured to display your existing remote

control keys and it must be programmed to send the

correct infrared signals.

This chapter guides you through the Touch Screen layout

and SRC-3000 setup procedures.

NOTE: The SRC-3000 includes eight default devices,

including TV, satellite TV, VCR, DVD player, hi-fi stereo,

radio/cassette player, CD player, and auxiliary.

LCD Layout: Device Keys

Layout edit mode enables you to customize the SRC-3000’s

Touch Screen display to match your existing remote

controls.

1. Press any device key for

three seconds to enter the

confirmation screen.

2. Press the four numerical keys

in any sequence to enter the

selection screen.

3. Press and to scroll

through the options. Select

Key mode and press

LCD Layout: Device Keys

4. On the device page, select

a key you want to modify.

Continue pressing the key to

scroll through the available

choices for the key.

5. Press

to display the

available icons for the page

of LCD display and repeat

Step 4 to finish all

modifications.

NOTE: You can also change the

layout for device keys. Repeat

Steps 1-3 and select Bank mode

in Step 3. You can set up two

devices for each key under Bank

mode for the four device keys

SAT/Cable, DVD/DVD Record,

Tuner/Tape and CD/MD (refer to

the Figure on the right.)

6. After you have finished

customizing the layout, press

to confirm changes or

to exit without making

any changes.

SRC-3000 User’s Manual

Code and Learn Setting Key

Press (Code setup key) for three seconds to enter the

confirmation screen. Then press the four numerical keys in

any sequence to enter the selection screen. Press

and

to scroll through the following options.

• Code: Use this option to automatically configure all

keys on the SRC-3000 for use with a specific

manufacturer’s model number. This option is the

fastest way to program the SRC-3000 but requires that

your device be located in the Pre-programmed Code

List that was bundled with the SRC-3000. Refer to the

supplied code list. Some newer or less-common

devices may not be pre-programmed and their codes

must be learned using the Learning Function by the

SRC-3000.

• Learn: Use this option to directly learn the infrared

signals from another remote control. This option is

perfect for newer or less common devices, or if a

certain key does not perform the desired function

after using the CODE option. However, if you come

across the problem that the SRC-3000 cannot learn

your device codes, refer to “Troubleshooting” on page

36 or contact the dealer.

Using Pre-programmed Code to Program Devices

Follow these instructions to program a device using pre-

programmed codes.

Manually Selecting the Code

1. Select a device (for example

TV).

2. Turn on the target device you

want the SRC-3000 to control.

3. Search for the four-digit code

number of your target device

in the Pre-programmed Code

List.

NOTE: If there is no entry for your target device, try

automatically selecting the code.

SRC-3000 User’s Manual

4. Enter the four-digit code

number manually to finish the

setting.

NOTES:

• Some codes are designed to operate more than

one model. It may take several tries to find the code

that works with your unit.

• When you enter the manufacturer’s code and an

icon is displayed, it could be that the code

number doesn’t exist in the manufacturer’s code

table yet.

• Each device set up can be used for any type of

target devices under the manually programming

procedure only.

Example: You have two different types of TV device and want

to be set up in a SRC-3000.

1. The first target device (TV1) is set up by following

up the indications of the user’s manual.

2. The second target device (TV2) set up likes the

first step, but the device you select from SRC-3000

should be the others ( for example Tuner,

DVD, ….etc.)

Using Pre-programmed Code to Program Devices

Automatically Selecting the Code

1. Automatically Selecting the Code

2. Turn on the target device you

want the SRC-3000 to control.

3. Press the device key (for example

TV). Point the SRC-3000 at the

target device.

4. Press

. Wait for the device to

turn off and immediately touch

any part of the screen to stop

automatic searching.

5. Press

and keys to look

for the correct power key of the

device to turn on the device.

6. Press

to confirm if the number

is correct. Now press the

key

to show the correct pre-

programmed code in sequence.

7. Press

to confirm the selection

and save settings or click

cancel.

NOTES:

• Each device can auto search the target device

code under the same classification only.

SRC-3000 User’s Manual

Using Code Learning Mode

Follow these instructions to enable the SRC-3000 to detect

and learn a remote control’s configuration.

Before Using Learning Mode

Note the following before using the SRC-3000’s learning

function: not all infrared codes are learnable by the SRC-

3000. You may need to collect the codes first. To change

from a device that has already been programmed, delete

all of the commands of the first device before teaching

new ones. For example, to operate the living room TV

instead of the bedroom TV, delete all commands for the

bedroom TV first. Then re-configure the TV device screen for

the living room TV.

NOTES:

• Code learning does not work with all devices.

• Select one device screen in advance before

using code learning mode.

• All keys except the Code Setup key, Delete key,

Macro key, and System setup key can be

learned.

Using Code Learning Mode

Learning from Another Remote Control

Before using learning mode, set both remotes on a flat

surface so that the target device’s remote control IR is

pointed at the SRC-3000’s learning eye, which is located at

the bottom of the unit. Keep a distance of 2-4 inches (5-10

cm).

1. Press

for three seconds to

enter the confirmation screen.

Refer to page 10.

2. Press and to scroll through the

options.

3. Select

and press .

4. Select a device (for example TV).

5. Point the target device’s remote control at the SRC-3000

learning eye located at the base of the unit (see Figure 1:

Front View). The SRC-3000 sequentially displays PAGE 1

and PAGE 2 and the keys to be pressed to lead you

through the operation.

6. The blinking frame denotes the key being learned. Press

the corresponding keys on the target device’s remote

control till it shows

, the next key will blink and the

remote code is recorded into the selected device key. If it

shows

please learn again.

SRC-3000 User’s Manual

The SRC-3000 will automatically guide you to the next button to

program by flashing it on the Touch Screen. When all buttons

are programmed on the current page it will automatically

switch to the next page. You can also directly select the next

button to program by touching it or press the device key to go

to the next page.

NOTE: If a key is preset with a code, appears on the

screen to remind you that the key is preset. Continuously

learning new codes overwrite the existing settings.

The SRC-3000 screen displays an

icon if the code

was successfully learned or an

icon if the code was

not learned.

NOTE: When the remote has learned the last key on the

page, the next page is automatically displayed.

7. Press

to exit learning mode.

Learning the Device key

The device key can store code. Under code learning model,

press device key for 3 seconds when the device frame is

blinking, press the target device’s remote control’s power key.

If the code was successfully learned, the SRC-3000 screen

displays an

icon.

Using Code Learning Mode

Erasing Key Codes and Device Codes (Delete)

Follow these instructions to delete key codes or device

codes from the SRC-3000.

1. Press the

key for three

seconds to enter the

confirmation screen.

2. Press the four numerical keys

in any sequence to enter the

selection screen. Refer to

page 10.

3. Press

and to scroll

through the options. Select

the Key or Bank that you

want to erase, and

press

4. If you select , select a device whose codes you want

to delete (for example TV). Delete each setting by

pressing any key.

5. Press

to cancel the operation or the SRC-3000 exits

automatically.

6. If you select Bank mode, selecting a device key will delete

all settings for the device. Pressing the Device key again

will change to the next page.

NOTE: Device keys can also save codes. To delete the

codes saved in device keys, press a device key for one

second to delete the saved remote code.

7. Press

to confirm deletion or to cancel the

operation.

SRC-3000 User’s Manual

Using Macros

A macro is a series of commands. The Macro feature

enables you to initiate a sequence of up to 60 commands

with a single key. You can create a macro on any control

key and insert time delays into the sequence. Remember,

however, assigning a macro eliminates the key’s original

function.

Creating a New Macro

Follow these steps to create a new macro.

1. Press Macro key for three

seconds to enter the

confirmation screen.

2. Press the four numerical keys

in any sequence to enter

Macro mode. The

the upper right begins to

flash.

3. Select a device key you

want to use for this macro

(for example TV), and then

press any key to define as

the macro key. You hear

three beeps to indicate that

macro creation mode has

started.

NOTE: If you select a key that already has a macro stored in

it, the new macro will replace the old macro.

4. Press the key sequence that you want to record.

Using Macros

5. Do one of the following:

• Press the

and then

press 1–9 to enter the

number of seconds you

want to delay between

each command. For

example, if you want a

two-second delay

between turning on your

TV and then turning on

your VCR, press ‘2’.

• Press

to confirm or

to cancel the

operation.

The following example will help you to better understand

creating a macro sequence. It is provided to teach you

how to record a macro but is by no means the only macro

sequence you can create.

Example: the following example defines a macro that turns

on your TV, switches the TV to DVD viewing mode, turns on

the DVD, delay 5 seconds and plays a DVD.

1. Press the TV device key.

2. Press the TV power key.

3. Press the TV/Video key.

4. Press the DVD device key.

5. Press the DVD power key.

6. Press the Delay key to select the time delay (5 sec)

for this step.

7. Press the DVD play key.

NOTE: You cannot use the Macro function to call up

another specific macro setting. If the currently set macro

key sequence contains an existing preset macro key, it will

skip the key and does not start the preset macro sequence

which the preset macro key triggers.

SRC-3000 User’s Manual

Resetting the SRC-3000 to Factory Defaults

This item enables you to set the SRC-3000 back to the

factory default configuration.

NOTE: All macros and user-defined keys are erased when

resetting the SRC-3000 to factory defaults.

1. Press the

Delete key for

three seconds to enter the

confirmation screen.

2. Press the four numerical keys

in any sequence to enter the

selection screen.

3. Press

or to select

and then press

4. You are prompted to confirm

the reset. Press the four

numerical keys in any

sequence again. SRC-3000

will return to the factory

defaults.

5. When

appears, the

reset is finished. The SRC-3000

will automatically return to

the original layout screen.

Chapter 4 Miscellaneous Settings

This chapter will describe how to use transmission feature,

set up the backlight, and enable the beep sound.

Using the Transmission Feature

The SRC-3000 can transmit data to another SRC-3000. You

can transmit preprogram and flash memory data.

NOTE: Before you use this feature to transfer data, you must

connect two devices with the optional connection cable.

Refer to Appendix B for more information.

1. Press and hold for three

seconds to enter the system

setup function. Press the four

numerical keys in any

sequence in the

confirmation screen.

2. Press

or to select .

3. Press

to begin

transmission.

4. During the transmission, the

LCD displays blank keys as

shown in the illustration on

the next page.

SRC-3000 User’s Manual

When the transmission is

completed,

displayed on the LCD. If

there is an error in

transmitting the data,

displayed.

5. For a double transmission,

repeat Step 3.

6. Press

to cancel the

transmission.

NOTE:

Only need to operate on the

sender remote control when

transmit. Ensure that both SRC-

3000 remote controls have fresh

batteries and are turned on, and

then connect the transmission

wire to transmit the data.

Setting the Backlight Mode

Set Backlight On Mode

1. Follow the steps shown in

the Transmission section Steps 1-2,

but select

instead of .

2. Press a numerical key 1-6 to

select the time that the backlight

stays on after pressing a key.

NOTE: The backlight ON time can be

set from 10 to 60 seconds in 10-second

increments, '1' for 10 seconds, '2' for 20

seconds, and so on.

SRC-3000 User’s Manual

Set Backlight Sensor Sensitivity

1. Refer to Set Backlight On Mode,

Step 1 and press

or to set the

light sensor sensitivity. The number

of frames indicates the current

setting value. The light sensor

sensitivity levels are 1~ 8.

The more frames you select, the

more sensitively the backlight

reacts to the ambient lighting.

The SRC-3000 activates the

backlight automatically. The

backlight function cannot be

turned off. When the light is off in

the environment, the SRC-3000

activates the backlight

automatically.

2. Press

to confirm or to

cancel the operation.

Setting the Beep Signal

1. Follow the steps shown in the

Transmission section Step 1-2,

but select

instead of .

2. Press to toggle the beep

on and off. When on,

appears on the LCD screen.

Press to exit.

Beep enabled icon

Chapter 5 Controlling Devices

The SRC-3000 is designed to be simple and straightforward

to operate. This chapter explains how to use the SRC-3000

to control all your devices.

NOTE: This chapter assumes you have already set up the

SRC-3000 and assigned Infrared codes to different keys. See

Chapter 3 Setting Up the SRC-3000 on page 12 for more

information on assigning codes.

Alternating Touch Screen Pages

Press a device key to alternate between page 1 and

page 2.

Viewing the Macro Key

You can view which keys are assigned to macros for any

particular device. Follow these instructions:

1. Press the device key (for

example TV).

Macro Interruption

2. Press the key. The

assigned macro keys

are displayed for this

device page.

For example, if you set

number 9 as the macro key

for TV- PAGE 1, when you

press the

key, the

preset macro key “9” will

appear.

3. If you want to check the

macro key for Page 2,

press the device key to

switch to the second

device page, and then

repeat Step 2.

Macro Interruption

After pressing the preset Macro key for a device, you

can interrupt the command sequence by pressing

on the upper left corner. The

message appears

and the Macro stops.

SRC-3000 User’s Manual

Controlling Devices

1. Make sure the SRC-3000 is pointing at the target

device.

2. Tap gently on the Touch Screen.

3. Select a device key and give remote commands

as usual.

appears, the pressed key is not pre-programmed with

a specific function.

NOTE: The Record Key (under VCR device, page 1) must be

held down for two seconds. As a safety feature, the record

key needs to be pressed for two seconds. This is to prevent

accidentally pressing the VCR record key and overwriting a

tape.

Functions

Appendix A

Functions and Specifications

Functions

• 8-in-1 IR learning type and pre-programmed remote

control

• High performance MCU capable of upgrading

programs

• 512 KB Flash Memory for learning/pre-programming

codes, so that you never lose your data

• Each device includes up to 56 keys on two pages

• Capable of learning carrier (frequency: 20KHz-455

KHz) and pulse codes

• Capable of deleting single key, single device or all

remote codes

• User-definable device layout

• Macro key can have up to 60 commands, including

time delays between commands

• Macro commands are shown on the LCD screen

while being replayed

• Backlight lights up automatically depending on the

environment

• Automatic Power Saving function

• Movement detection function to turn on SRC-3000

automatically

• Battery low indicator

SRC-3000 User’s Manual

Specifications

Model SRC-3000

Dimensions (WxHxD) 3.1 x 7.5 x 1.25 inches

(7.9 x 19 x 3.2 cm)

Weight (without Batteries) 210 g

Number of Device 8 devices

Keys 2 pages/56 keys/ each device

Backlighting Blue LED

Learning Frequency 20 KHz – 455 KHz & pulse up to

256 bits long

Memory 512 KB flash memory

Batteries AAA x3 Alkaline batteries

Power Consumption

LCD Off: 50 µA

LCD On: 300 µA

Operation: 30–150 mA (Max.)

Operating Distance Approx. 30 feet (8-10 meters)

Interface UART/115,200 bps (optional

SLC-2080 USB cable)

IR Distance 8-10 meters

LCD Screen (W*H) TN LCD 2.3 x 4.8 inches

(5.8 cm x 12 cm)

Appendix B Accessories

Transmit wire (SLC-2080 USB cable)

The transmit wire is an optional link cable that enables

transmission of system setup to another SRC-3000. All

settings including MCU program, data in the flash memory

and pre-programmed code will be transferred using the

TRANS selection as described in Chapter 4 “Miscellaneous

Settings.”

By connecting a transmit wire between two SRC-3000s, you

can duplicate settings and functions from one SRC-3000 to

another.

Appendix C Troubleshooting

Troubleshooting Tables

Problem Solution

LCD does not show anything

when you touch it.

Batteries may be dead.

Replace the batteries with

three new AAA alkaline

batteries (page 7).

Check that the batteries

are properly installed.

The SRC-3000 doesn’t operate

a device.

Make sure that the desired

device key on the SRC-3000

LCD panel has been

selected.

Move closer to the device.

The maximum operating

distance is approximately

30 feet.

Ensure that you are aiming

the SRC-3000 directly at the

device and that there are

no obstructions between

the SRC-3000 and the

device.

Ensure programming with

the learning function (page

18) or the manufacturer

codes has been properly

done.

Re-teach the key (page

14).

Troubleshooting Tables

Problem Solution

You cannot operate a device

even after teaching the

device using the learning

function.

Make sure that your SRC

3000 has correctly learned

the target device’s remote

control code (page 19).

Delete the device data

from the SRC-3000 and

carry out the learning

function again (page 19).

Make sure you did not

program more than one

remote for a given device.

You see “ERROR” display on

the LCD during the learning

procedure.

Make sure you hold the

target remote’s key till the

screen displays Ok or Error

on the screen.

Make sure the two remotes

are not too close or too far

apart - keep them about

2~4 inches (5~10 cm) apart,

and your device remote

control is aiming directly at

the SRC-3000’s learning

eye.

You see “ERROR” displayed

during operation.

The key that you pressed

has not been taught.

Teach the key using the

learning procedure (page

18).

Your VCR will not record. As a safety feature on the

SRC-3000, you must press

the REC key for two

seconds.

SRC-3000 User’s Manual

Problem Solution

IR LEARNING is not successful. Replace batteries in the

SRC-3000 and the remote

you are trying to configure.

Keep the distance

between the remote

control and the SRC-3000’s

learning eye to about 2~4

inches.

Do not use the learn

function near an

incandescent lamp.

Memory capacity is full (56

keys for each of eight

models).

The learning process has no

errors, but you still can’t

control your AV devices:

repeat the learning

procedure again. If you still

can’t solve the problem,

contact Sunwave for help.

Original remote might not

be compatible with

learning procedure.

Macro does not work. Be sure to aim the SRC-3000

at the devices while the

macro commands are

being sent.

Macro was not properly set

up. Repeat macro set-up

procedure (page 22).

Troubleshooting Tables

Problem Solution

A key of your existing remote

performs two or more

functions

Some remotes issue multiple

commands when a key is

held down. Please be sure

to teach different keys of

SRC-3000 for these different

commands. Each key of

SRC-3000 can only learn

one command.

The LCD screen turns off. The SRC-3000 is preset

automatically to switch the

LCD off after the Power

Down time (90 seconds).

Just tap the touch screen

to turn the SRC-3000 back

on again.

Sunwave src 3000 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info