751651
18
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
7.1.2 Motor Setting
If you are using DiSEqC 1.2 or USALS, you can install satellites which are received by a motorised dish.
For the correct installation and positioning of your motor, we recommend the support/advice of a
professional and experienced installer. Here you can configure the motor type and set the motor
position for a satellite that you want to receive.
Satellite Press OK to open the list of available satellites and select one by using the
pq or P+/P buttons, then press OK again for confirmation.
Transponder Press OK to open the list of available transponders if you like to set a specific
transponder for the selected satellite.
DiSEqC Motor Choose between DiSEqC 1.2 and USALS or Off. Per default it is Off because of
pre-defined setup for DiSEqC 1.0.
DiSEqC 1.2 selection
Move step-wise Press t u to move your antenna east or west. Move carefully until you see
that both signal beams have an acceptable reception level. When you find
the selected satellite, press and select Yes to save the position.
Move continuously Use this function to move quickly to a desired position by holding down
the t or u key, depending on the direction in which you want to move the
antenna. Also, be very careful with it, so you do not bump into obstacles.
Limit Press OK to open this sub-menu, which allows you to set the mechanical
limits for your motor. This is only necessary if your antenna is mounted which
means, that a wall, a tree or similar physical blockages could interfere with a
free movement of the antenna or motor.
Save to this position You can store this position between 0 and 63, OK can be used again as
described above.
Save/Recalculation With Save and Recalculate, you can set whether the position should be saved
or a new calculation should be made after setting this position.
Go to position Press OK to move the motor to the centre position. This is only necessary for
the first time to set the antenna correctly. Then you can also select a number
of a position you already have stored or check the antenna position.
USALS selection
Configure the motor position by using the USALS function. Enter your geographic location. The motor
is able to calculate all available satellite positions, preconditioned this function is also supported by the
motor. Use pq to select the Antenna Position sub-menu.
Antenna position: Press OK to open the submenu. Use the 0 ~ 9 buttons to enter the degree of
longitude. Next, select East or West, then 0 ~ 9 to enter the latitude. Finally,
specify North or South. Finally, select Save and press OK to confirm your
entries.
Go to position Press OK to move the motor to the desired satellite position. After
computation, you can also select other satellites, go to Satellite and select the
desired one from the list.
NOTE: For detailed information about correct geographic locations for your
location, visit websites such as dishpointer.com, itouchmap.com, or other
reliable sources such as professional journals.
14
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Strong SRT 7501 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Strong SRT 7501 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Strong SRT 7501

Strong SRT 7501 Gebruiksaanwijzing - Deutsch - 35 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info