751651
12
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
4.0 STARTING UP FOR THE FIRST TIME
Ensure that your satellite signal is of good quality and that all connections are properly setup. In case of
difficulties or questions, please ask your local dealer or service hotline for assistance. It is recommended
to follow the First Time Installation step by step. It will guide you through the basic installation and setup
process. You can enjoy digital HD broadcasts within just a few minutes. To enjoy the complete range of
channels and to watch your preferred scrambled services, it is recommended to insert the ORF Digital
smartcard. Then continue with the first time installation. Please pay attention to the correct insertion of
the smartcard.
4.1 Language and Video Settings
After connecting your receiver for the first time, the OSD Language, Aspect Ratio, Aspect Conversion and
HDMI Resolution menus will be shown. Change your language with t u and use pq to select the other
settings. For these settings, you can also use OK to show a list of available settings. Adjust the Aspect
Ratio according to your TV (4:3 for an analogue CTV set and 16:9 for your new flat screen/HD TV) and
select the Conversion of your preference.
For HDMI Resolution the default setting 720p is recommended, but many TVs already support higher
resolutions. Therefore you can choose Auto (it will check the highest resolution supported by the TV) or
1080i. 1080p will only be supported after a future software update.
NOTE: If you select an HDMI resolution which your TV does not support, the
receiver will switch to the previous setting automatically after ~10 sec. If you
can see the displayed message, please confirm the selected resolution by
pressing OK.
During any stage of the First Time Installation, you can press BLUE Next to go to the next step or YELLOW
Previous to get back to the previous step.
4.2 Antenna Setup
This receiver is already adjusted for reception of Astra 19.2 satellite with the correct settings as it is
most common. Per default it is setup for DiSEqC port 1, but you can use the setting as well if you are
not connected to any switch. You only need to change these settings if you are not connected to Astra
19.2 or you don't have this satellite connected to port 1 of your DiSEqC switch. To adjust your antenna
settings for the Satellite, LNB Power, LNB Type, LNB Freq, DiSEqC 1.0 and Transponder correctly, use the
t u and pq buttons.
For the better convenience and if you have a multi dish installation, we support the Auto DiSEqC Scan*
function, which can be activated by pressing the GREEN button.
For further details and information about the settings, see chapter 7.1.1 Antenna Setup
Within the First Time Installation it is only possible to adjust settings for up to 4 satellite positions. In
order to proceed with First Time Installation, use BLUE Next to go forwards.
* This new function can recognise available satellites in the persisting antenna installation. The predefined satellites are: Astra 19.2E, Astra
23.5E, Astra 28.2E, HotBird 13.0E and Eutelsat 9.0E.
4.3 Channel list selection
In this menu you can highlight the channel list of your choice by pressing t u and then choose the
appropriate option in below.
8
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Strong SRT 7501 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Strong SRT 7501 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Strong SRT 7501

Strong SRT 7501 Gebruiksaanwijzing - Deutsch - 35 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info