Handleiding Stihl MS361C (pagina 1 van 138) (Spaans)

52205

Verklein

Vergroot

Pagina terug

1/138

Pagina verder

Instruction Manual

Manual de instrucciones

STIH)

Read and follow all safety precautions in

Instruction Manual – improper use can cause

serious or fatal injury.

Lea y siga todas las precauciones de

seguridad dadas en el manual de

instrucciones – el uso incorrecto puede causar

lesiones graves o mortales.

Warning!

To reduce the risk of kickback injury use

STIHL reduced kickback bar and STIHL RM2,

RMC3 (0,325") or RM2, RSC3 (3/8") chain

depending on sprocket or other available low

kickback components.

Advertencia!

Para reducir el riesgo de lesionarse como

resultado de un culatazo, utilice la barra de

contragolpe reducido y la cadena RM2, RMC3

(0,325 pulg) o RM2, RSC3 (3/8 pulg) de

STIHL, dependiendo de la rueda dentada

usada y de otros componentes reductores de

contragolpe.

STIHL MS 361 C

BA_MS361C_86_U_M6.book Seite 0 Mittwoch, 22. November 2006 11:19 11

1MS 361 C

English / USA

BA_SE_144_004_01_05.fmPrinted on chlorine-free paper.

Printing inks contain vegetable oils; paper can be recycled.

0458 214 8621 A. M0,5. D8. PM. Printed in USA

STIHl

Contents

Secondary Chain

Braking System ................................ 2

Guide to Using this Manual .............. 3

Safety Precautions and

Working Techniques ......................... 4

Mounting the Bar and Chain

(Side chain tensioner) .................... 27

Mounting the Bar and Chain

(Quick Chain Tensioner) ................. 28

Tensioning the Saw Chain

(Side chain tensioner) .................... 31

Tensioning the Saw Chain

(Quick chain tensioner) .................. 32

Checking Chain Tension ................. 32

Fuel ................................................ 32

Fueling ............................................ 33

Chain Lubricant .............................. 35

Filling Chain Oil Tank ...................... 35

Checking Chain Lubrication ........... 36

Chain Brake ................................... 36

Winter Operation ............................ 38

Information Before You Start .......... 39

Starting / Stopping the Engine ........ 39

Operating Instructions .................... 43

Oil Quantity Control ........................ 44

Taking Care of Guide Bar ............... 44

Air Filter System ............................. 45

Cleaning the Air Filter ..................... 45

Motor Management ........................ 46

Adjusting the Carburetor ................ 46

Spark Arresting Screen

in Muffler ........................................ 48

Checking the Spark Plug ................ 48

Replacing Starter Rope

and Rewind Spring ......................... 49

Storing the Machine ....................... 52

Checking and Replacing

Chain Sprocket ............................... 52

Maintaining and Sharpening

Saw Chain ...................................... 54

Maintenance Chart ......................... 58

Main Parts of the Saw .................... 60

Specifications ................................. 62

Special Accessories ....................... 63

Ordering Spare Parts ..................... 63

Maintenance and Repairs .............. 64

STIHL Incorporated

Federal Emission Control

Warranty Statement ........................ 65

Trademarks .................................... 67

Allow only persons who understand this

Manual to operate your chainsaw.

To receive maximum performance and

satisfaction from your STIHL chainsaw,

it is important that you read and

understand

the maintenance and safety

precautions,

starting on page 4, before

using your chainsaw.

Contact your STIHL dealer or the STIHL

distributor for your area if you do not

understand any of the instructions in this

Manual.

!Warning!

Because a chainsaw is a high-speed

wood-cutting tool, some special safety

precautions must be observed as with

any other power saw to reduce the risk

of personal injury.

Careless or improper use may cause

serious or even fatal injury.

STIHL's philosophy is to continually

improve all of its products. As a result,

engineering changes and improvements

are made from time-to-time. If the

operating characteristics or the

appearance of your chainsaw differs

from those described in this Manual,

please contact your STIHL dealer for

information and assistance.

English / USA

MS 361 C

This STIHL chainsaw is equipped with a

chain brake system that can be

activated in three different ways. As

before, the chain brake can be activated

by the inertia of the front hand guard in

certain kickback situations or manually

by pushing the front hand guard toward

the bar nose. In both of these cases the

brake, once activated, is designed to

bring the chain to a standstill within

fractions of a second. In addition, there

is a secondary system that is designed

to stop chain rotation within a second of

you letting go of the rear handle. The

locked chain is not released again until

you press down the throttle trigger

interlock lever to operate the throttle.

The chain brake can be activated in

three ways:

1 By inertia in certain kickback

situations

2 Manually via the front hand guard

3 Manually by releasing the rear

handle

The activating mechanism for the

secondary chain braking system is

integrated in the throttle trigger interlock

lever (rear handle). One of the big

advantages of this system is that the

saw chain is automatically locked in

position for engine starts and when

carrying the running saw by the front

handle (with the rear handle released).

To reduce the risk of personal injury

or property damage during cutting,

observe the characteristics that

make this saw different from saws

not equipped with a secondary

chain braking system. Before

operating the chainsaw for the first

time, make sure you are familiar

with how the rear-handle activation

works. Pay special attention to the

chapters "Chain Brake" and

"Starting/Stopping the Engine".

Secondary Chain

Braking System

150BA000 KN

3MS 361 C

English / USA

Pictograms

All the pictograms attached to the

machine are shown and explained in

this manual.

The operating and handling instructions

are supported by illustrations.

Symbols in text

The individual steps or procedures

described in the manual may be marked

in different ways:

: A bullet marks a step or procedure

without direct reference to an

illustration.

A description of a step or procedure that

refers directly to an illustration may

contain item numbers that appear in the

illustration.

Example:

Loosen the screw (1)

Lever (2) ...

In addition to the operating instructions,

this manual may contain paragraphs

that require your special attention. Such

paragraphs are marked with the

symbols described below:

Warning where there is a risk of an

accident or personal injury or

serious damage to property.

Caution where there is a risk of

damaging the machine or its

individual components.

Note or hint which is not essential

for using the machine, but may

improve the operator’s under-

standing of the situation and result

in better use of the machine.

Note or hint on correct procedure in

order to avoid damage to the

environment.

Equipment and features

This instruction manual may refer to

several models with different

features. Components that are not

installed on all models and related

applications are marked with an

asterisk (*). Such components may

be available as special accessories

from your STIHL dealer.

Engineering improvements

STIHL’s philosophy is to continually

improve all of its products. As a result,

engineering changes and improvements

are made from time to time. If the

operating characteristics or the

appearance of your machine differ from

those described in this manual, please

contact your STIHL dealer for

assistance.

Therefore some changes, modifications

and improvements may not be covered

in this manual.

Guide to Using this Manual

English / USA

MS 361 C

Because a chainsaw is a

high-speed, fast-cutting

power tool, special safety

precautions must be

observed to reduce the

risk of personal injury.

It is important that you

read, fully understand and

observe the following

safety precautions and

warnings. Read the

instruction manual and

the safety instructions periodically.

Careless or improper use may cause

serious or fatal injury.

!Warning!

Reactive forces, including kickback, can

be dangerous. Pay special attention to

the section on reactive forces.

Have your STIHL dealer show you how

to operate your power tool. All safety

precautions that are generally observed

when working with an axe or a hand saw

also apply to the operation of chainsaws.

Observe all applicable federal, state and

local safety regulations, standards and

ordinances. When using a chain saw for

logging purposes, for instance, refer to

the OSHA regulations for “logging

operations“ at 29 Code of Federal

Regulations 1910.266.

!Warning!

Do not lend or rent your power tool

without the instruction manual. Be sure

that anyone using it understands the

information contained in this manual.

!Warning!

The use of this machine may be

hazardous.The saw chain has many

sharp cutters. If the cutters contact your

flesh, they will cut you, even if the chain

is not moving. At full throttle, the chain

speed can reach 67 mph (30 m/s).

Use your chainsaw only for cutting

wooden objects. It must not be used for

any other purposes, since such misuse

may result in an accident or damage to

the machine.

!Warning!

Minors should never be allowed to use

this power tool. Bystanders, especially

children, and animals should not be

allowed in the area where it is in use.

!Warning!

To reduce the risk of injury to bystanders

and damage to property, never let your

power tool run unattended. When it is

not in use (e.g. during a work break),

shut it off and make sure that

unauthorized persons do not use it.

Most of these safety precautions and

warnings apply to the use of all STIHL

chainsaws. Different models may have

different parts and controls. See the

appropriate section of your instruction

manual for a description of the controls

and the function of the parts of your

model.

Safe use of a chainsaw involves

1. the operator

2. the saw

3. the use of the saw.

THE OPERATOR

Physical Condition

You must be in good physical condition

and mental health and not under the

influence of any substance (drugs,

alcohol, etc.) which might impair vision,

dexterity or judgment. Do not operate

this machine when you are fatigued.

!Warning!

Be alert – if you get tired, take a break.

Tiredness may result in loss of control.

Working with any power tool can be

strenuous. If you have any condition that

might be aggravated by strenuous work,

check with your doctor before operating

this machine.

Safety Precautions and

Working Techniques

5MS 361 C

English / USA

!Warning!

Prolonged use of a power tool (or other

machines) exposing the operator to

vibrations may produce whitefinger

disease (Raynaud's phenomenon) or

carpal tunnel syndrome.

These conditions reduce the hand's

ability to feel and regulate temperature,

produce numbness and burning

sensations and may cause nerve and

circulation damage and tissue necrosis.

All factors which contribute to white-

finger disease are not known, but cold

weather, smoking and diseases or

physical conditions that affect blood

vessels and blood transport, as well as

high vibration levels and long periods of

exposure to vibration are mentioned as

factors in the development of whitefinger

disease. In order to reduce the risk of

whitefinger disease and carpal tunnel

syndrome, please note the following:

– Most STIHL power tools are

available with an anti-vibration

(“AV”) system designed to reduce

the transmission of vibrations

created by the machine to the

operator's hands. An AV system is

recommended for those persons

using power tools on a regular or

sustained basis.

– Wear gloves and keep your hands

warm. Heated handles, which are

available on some STIHL power-

heads, are recommended for cold

weather use.

– Keep the AV system well

maintained. A power tool with loose

components or with damaged or

worn AV buffers will tend to have

higher vibration levels.

Keep the saw chain sharp. A dull

chain will increase cutting time, and

pressing a dull chain through wood

will increase the vibrations

transmitted to your hands.

– Maintain a firm grip at all times, but

do not squeeze the handles with

constant, excessive pressure. Take

frequent breaks.

All the above-mentioned precautions do

not guarantee that you will not sustain

whitefinger disease or carpal tunnel

syndrome. Therefore, continual and

regular users should closely monitor the

condition of their hands and fingers. If

any of the above symptoms appear,

seek medical advice immediately.

!Warning!

The ignition system of the STIHL unit

produces an electromagnetic field of a

very low intensity. This field may

interfere with some pacemakers. To

reduce the risk of serious or fatal injury,

persons with a pacemaker should

consult their physician and the

pacemaker manufacturer before

operating this tool.

Proper Clothing

!Warning!

To reduce the risk of injury, the operator

should wear proper protective apparel.

Clothing must be sturdy

and snug-fitting, but allow

complete freedom of

movement. Wear long

pants made of heavy

material to help protect

your legs from contact with branches or

brush. To reduce the risk of cut injuries,

wear pants or chaps that contain pads of

cut retardant material.

Avoid loose-fitting jackets, scarfs,

neckties, jewelry, flared or cuffed pants,

unconfined long hair or anything that

could become caught on branches,

brush or the moving parts of the unit.

Secure hair so it is above shoulder level.

Good footing is very

important. Wear sturdy

boots with nonslip soles.

Steel-toed safety boots

are recommended.

English / USA

MS 361 C

!Warning!

Wear an approved safety

hard hat to reduce the risk

of injury to your head.

Chainsaw noise may

damage your hearing.

Wear sound barriers (ear

plugs or ear mufflers) to help protect

your hearing. Continual and regular

users should have their hearing checked

regularly.

Be particularly alert and cautious when

wearing hearing protection because

your ability to hear warnings (shouts,

alarms, etc.) is restricted.

Never operate your power tool unless

wearing goggles or properly fitted

protective glasses with adequate top

and side protection complying with ANSI

Z 87.1 (or your applicable national

standard). To reduce the risk of injury to

your face STIHL recommends that you

also wear a face shield or face screen

over your goggles or protective glasses.

Always wear gloves when

handling the machine and

the cutting tool. Heavy-

duty, nonslip gloves

improve your grip and

help to protect your

hands.

STIHL offers a wide range of protective

clothing and equipment.

THE POWER TOOL

For illustrations and definitions of the

power tool parts see the chapter on

“Main Parts and Controls.”

!Warning!

Never modify this power tool in any way.

Only attachments supplied by STIHL or

expressly approved by STIHL for use

with the specific STIHL model are

authorized. Although certain

unauthorized attachments are useable

with STIHL power tools, their use may, in

fact, be extremely dangerous.

If this tool is subjected to unusually high

loads for which it was not designed (e.g.

heavy impact or a fall), always check

that it is in good condition before

continuing work. Check in particular that

the fuel system is tight (no leaks) and

that the controls and safety devices are

working properly. Do not continue

operating this machine if it is damaged.

In case of doubt, have it checked by your

STIHL servicing dealer.

THE USE OF THE POWER TOOL

Transporting the Power Tool

!Warning!

To reduce the risk of injury from saw

chain contact, never carry or transport

your power tool with the saw chain

moving. Always engage the chain brake

when taking more than a few steps.

!Warning!

Always switch off the engine, and fit the

chain guard (scabbard) over the chain

and guide bar before transporting the

power tool over longer distances. When

transporting it in a vehicle, properly

secure it to prevent turnover, fuel

spillage and damage to the unit.

It may be carried only in a horizontal

position. Grip the front handle in a

manner that the machine is balanced

horizontally. Keep the hot muffler away

from your body and the cutting

attachment behind you.

001BA115 KN

7MS 361 C

English / USA

Fuel

Your STIHL power tool uses an oil-

gasoline mixture for fuel (see the chap-

ter on “Fuel” of your instruction manual).

!Warning!

Gasoline is an extremely

flammable fuel. If spilled

and ignited by a spark or

other ignition source, it

can cause fire and serious

burn injury or property

damage. Use extreme caution when

handling gasoline or fuel mix.

Do not smoke or bring any fire or flame

near the fuel or the power tool. Note that

combustible fuel vapor may escape from

the fuel system.

Fueling Instructions

!Warning!

Fuel your power tool in well-ventilated

areas, outdoors. Always shut off the

engine and allow it to cool before

refueling. Gasoline vapor pressure may

build up inside the fuel tank depending

on the fuel used, the weather conditions

and the tank venting system.

In order to reduce the risk of burns and

other personal injury from escaping gas

vapor and fumes, remove the fuel filler

cap on your power tool carefully so as to

allow any pressure build-up in the tank

to release slowly. Never remove the fuel

filler cap while the engine is running.

Select bare ground for fueling and move

at least 10 feet (3 m) from the fueling

spot before starting the engine. Wipe off

any spilled fuel before starting your

machine.

!Warning!

Check for fuel leakage while refueling

and during operation. If fuel leakage is

found, do not start or run the engine until

the leak is fixed and any spilled fuel has

been wiped away. Take care not to get

fuel on your clothing. If this happens,

change your clothing immediately.

Different models may be equipped with

different fuel caps.

Cap with grip

!Warning!

In order to reduce the risk of fuel spillage

and fire from an improperly tightened

fuel cap, correctly position and tighten

the fuel cap in the fuel tank opening.

To do this with this STIHL

cap, raise the grip on the

top of the cap until it is

upright at a 90° angle.

Insert the cap in the fuel

tank opening with the

triangular marks on the grip of the cap

and on the fuel tank opening lining up.

Using the grip, turn the cap firmly

clockwise as far as it will go (approx. a

quarter turn).

Fold the grip flush with the

top of the cap. If the grip

does not lie completely

flush with the cap and the

detent on the grip does

not fit in the

corresponding recess in the filler

opening, the cap is not properly seated

and tightened and you must repeat the

above steps.

Screw cap

!Warning!

Unit vibrations can cause an improperly

tightened fuel filler cap to loosen or

come off and spill quantities of fuel. In

order to reduce the risk of fuel spillage

and fire, tighten the fuel filler cap by

hand as securely as possible.

The screwdriver end of

the STIHL combination

wrench or other similar

tool can be used as an aid

in tightening slotted fuel

filler caps.

See "Fueling" chapter in your instruction

manual.

English / USA

MS 361 C

Before Starting

Take off the chain guard (scabbard) and

inspect the saw for proper condition and

operation. (See the maintenance chart

near the end of the instruction manual.)

!Warning!

Always check your power tool for proper

condition and operation before starting,

particularly the throttle trigger, throttle

trigger interlock, stop switch and cutting

tool. The throttle trigger must move

freely and always spring back to the idle

position. Never attempt to modify the

controls or safety devices.

!Warning!

Never operate your power tool if it is

damaged, improperly adjusted or

maintained, or not completely or

securely assembled.

!Warning!

Check that the spark plug boot is secure

– a loose boot may cause arcing that

could ignite combustible fumes and

cause a fire.

For proper assembly of the bar and

chain follow the procedure described in

the chapter "Mounting the Bar and

Chain" of your instruction manual.

STIHL Oilomatic chain, guide bar and

sprocket must match each other in

gauge and pitch. Before replacing any

bar and chain, see the sections on

"Specifications," "Kickback" and the

"ANSI B 175.1-2000 chainsaw kickback

standard" in the instruction manual.

!Warning!

Proper tension of the chain is extremely

important. In order to avoid improper

setting, the tensioning procedure must

be followed as described in your

manual. Always make sure the

hexagonal nut(s) for the sprocket cover

is (are) tightened securely after

tensioning the chain in order to secure

the bar. Never start the saw with the

sprocket cover loose. Check chain

tension once more after having

tightened the nut(s) and thereafter at

regular intervals (whenever the saw is

shut off). If the chain becomes loose

while cutting, shut off the engine and

then tighten. Never try to adjust the

chain while the engine is running!

Keep the handles clean and dry at all

times; it is particularly important to keep

them free of moisture, pitch, oil, fuel mix,

grease or resin in order for you to

maintain a firm grip and properly control

your power tool.

Starting

!Warning!

To reduce the risk of fire and burn

injuries, start the engine at least 10 feet

(3 meters) from the fueling spot,

outdoors only.

Start and operate your saw without

assistance. For specific starting

instructions, see the appropriate section

of the instruction manual. Proper starting

methods reduce the risk of injury.

!Warning

To reduce the risk of injury from chain

contact and/or reactive forces, the chain

brake must be engaged when starting

the saw.

!Warning

Do not drop start. This method is very

dangerous because you may lose

control of the saw.

There are two recommended methods

for starting your chainsaw.

9MS 361 C

English / USA

With the first recommended method,

the chainsaw is started on the ground.

Make sure the chain brake is engaged

(see "Chain Brake" chapter in your

instruction manual) and place the

chainsaw on firm ground or other solid

surface in an open area. Maintain good

balance and secure footing.

Grip the front handlebar of the saw firmly

with your left hand and press down. For

saws with a rear handle level with the

ground, put the toe of your right foot into

the rear handle and press down. With

your right hand pull out the starter grip

slowly until you feel a definite resistance

and then give it a brisk, strong pull.

The second recommended method for

starting your chainsaw allows you to

start the saw without placing it on the

ground. Make sure the chain brake is

engaged. Grip the front handle of the

chainsaw firmly with your left hand, keep

your left arm in a locked (straight)

position. Hold the rear handle of the saw

tightly between your legs just above the

knees. If you are using the rear-handle-

activated chain brake, be careful not to

disengage the brake by depressing the

interlock lever with your leg. Maintain

good balance and secure footing. Pull

the starting grip slowly with your right

hand until you feel a definite resistance

and then give it a brisk, strong pull.

!Warning!

Be sure that the guide bar and chain are

clear of you and all other obstructions

and objects, including the ground. When

the engine is started, the engine speed

with the starting throttle lock engaged

will be fast enough for the clutch to

engage the sprocket and, if the chain

brake is not activated, turn the chain. If

the upper quadrant of the tip of the bar

touches any object, it may cause kick-

back to occur (see section on reactive

forces). Never attempt to start the

chainsaw when the guide bar is in a cut

or kerf.

As soon as the engine is running,

immediately blip the throttle trigger,

which will disengage the starting throttle

lock and allow the engine to settle down

to idle.

!Warning!

As soon as you press down the interlock

lever, the rear-handle-activated chain

brake is disengaged and allows the

chain to run at high speed until you blip

the throttle trigger.

!Warning!

When you pull the starter grip, do not

wrap the starter rope around your hand.

Do not let the grip snap back, but guide

the starter rope to rewind it properly.

Failure to follow this procedure may

result in injury to your hand or fingers

and may damage the starter

mechanism.

001BA113 KN

001BA114 KN

English / USA

MS 361 C

Important Adjustments

!Warning!

To reduce the risk of personal injury from

loss of control or contact with the

running cutting tool, do not use your unit

with incorrect idle adjustment. At correct

idle speed, the cutting tool should not

move. For directions on how to adjust

idle speed, see the appropriate section

of your instruction manual.

If you cannot set the correct idle speed,

have your STIHL dealer check your

power tool and make proper

adjustments and repairs.

During Operation

Holding and controlling the power

tool

Always hold the unit firmly with both

hands on the handles while you are

working. Wrap your fingers and thumbs

around the handles.

Your right hand should grip the rear

handle. This also applies to left-handers.

With your hands in this position, you can

best oppose and absorb the push, pull

and kickback forces of your saw without

losing control (see section on reactive

forces).

!Warning!

To reduce the risk

of serious or fatal

injury to the

operator or

bystanders from

loss of control, never use the saw with

one hand. It is more difficult for you to

control reactive forces and to prevent

the bar and chain from skating or

bouncing along the limb or log. Even for

those compact saws designed for use in

confined spaces, one-handed operation

is dangerous because the operator may

lose control.

!Warning!

To reduce the risk of cut injuries, keep

hands and feet away from the cutting

tool. Never touch a moving cutting tool

with your hand or any other part of your

body.

!Warning!

Keep proper footing and balance at all

times. Special care must be taken in

slippery conditions (wet ground, snow)

and in difficult, overgrown terrain. Watch

for hidden obstacles such as tree

stumps, roots, rocks, holes and ditches

to avoid stumbling. There is increased

danger of slipping on freshly debarked

logs. For better footing, clear away fallen

branches, scrub and cuttings. Be

extremely cautious when working on

slopes or uneven ground.

!Warning!

Take extreme care in wet and freezing

weather (rain, snow, ice). Put off the

work when the weather is windy, stormy

or rainfall is heavy.

001BA087 LÄ

21MS 361 C

English / USA

Open-face technique

C = felling notch - determines the

direction of the fall

For an open-face cut:

: Properly place felling notch

perpendicular to the line of fall,

close to the ground.

: Cut down at app. 50-degree angle

to a depth of app.1/5 to 1/4 of the

trunk diameter.

: Make second cut from below at app.

40 degree angle.

: Remove resulting 90-degree piece.

Making sapwood cuts

: For medium sized or larger trees

make cuts at both sides of the trunk,

at same height as subsequent

felling cut.

: Cut to no more than width of guide

bar.

This is especially important in softwood

in summer - it helps prevent sapwood

splintering when the tree falls.

D = Felling cut

Conventional and open-face technique:

: Begin 1 to 2 inches (2,5 to 5 cm)

higher than center of felling notch.

: Cut horizontally towards the felling

notch.

: Leave approx.1/10 of diameter

uncut. This is the hinge.

: Do not cut through the hinge - you

could lose control of the direction of

the fall.

001BA150 KN

001BA144 KN

29MS 361 C

English / USA

: Remove the tensioning gear (4) and

turn it over.

: Unscrew the nut (5).

: Position the tensioning gear (4)

against the guide bar (6) so that the

stud (7) projects through the upper

hole and the short guide peg (8)

locates in the lower hole.

: Screw the nut (5) on to the stud as

far as stop.

Wear work gloves to protect your

hands from the sharp cutters.

: Turn the tensioning gear (4)

clockwise as far as stop.

: Fit the chain – start at the bar nose.

Pay attention to the position of the

tensioning gear and the cutting

edges.

133BA027 KN

133BA028 KN

133BA029 KN

133BA030 KN

133BA031 KN

English / USA

MS 361 C

Chain brake maintenance

The chain brake is subject to normal

wear and tear. It must therefore be

checked and serviced regularly by

trained personnel (e.g. STIHL dealer) at

the following intervals:

At temperatures below 50 °F,

preheat the carburetor as follows:

: Use the combination wrench or a

screwdriver to ease the shutter (1)

out of the summer position (s).

: Fit the shutter in the winter position

(r at top) – as shown in the

illustration.

Heated air from around the cylinder now

flows around the carburetor – this helps

prevent carburetor icing.

: At temperatures above 68 °F:

Return the shutter to the summer

position (s).

This is essential to avoid engine

running problems and overheating.

At temperatures below 14°F

It is advisable to use the cover plate

mounting kit (special accessory) in

extremely cold operating conditions

(temperatures below 14 °F, in powder or

drifting snow).

If engine idle speed is erratic or

acceleration is poor:

: Turn low speed screw (L) 1/4 turn

counterclockwise.

It is usually necessary to change the

setting of the idle speed screw (LA)

after making adjustments to the low

speed screw (L) – see “Adjusting the

Carburetor”.

Full-time professional

usage: every 3

months

Semi-professional

usage (farm and

construction industry): every 6

months

Hobby and occasional

usage: every 12

months

Winter Operation

213BA024 KN

213BA025 KN

Stihl MS361C Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Stihl MS361C

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info