608620
7
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
ENGLISH
EN
3.2 Installation of 107 M HD, 121 M
1. Place the cutting deck in position in front of the
machine.
2. Install the following components on both wheel
axles:
Washer (3:B).
Deck mount (3:C).
Washer (3:B).
Circlip (3:A).
3. Remove the pins on both sides. See fig. 7:I and
fig. 13.
4. Screw the arms into each other. See fig. 4.
5. Suspend the cutting deck in the implement lift-
er. See fig. 14.
6. If the deck has electrical cutting height adjust-
ment, connect the cable to the machine’s front
right socket. See fig. 15.
3.2.1 Belt, 107 M HD, 121 M
The cutting deck’s rear section should rest on the
floor (it should not be lifted or secured).
Install the belt as follows:
1. 107 M HD
: Set the maximum cutting height.
121 M
: Set the cutting height in the centre posi-
tion
2. Remove the belt cover. See fig. 8 and 10. The
number in the figure indicates the key width.
3. Locate the belt around the machine’s belt pulley
(16:M).
4. Force the belt onto the cutting deck’s belt pul-
ley.
5. Grip the belt tensioners lever with your left
hand. Pull the lever and apply the tensioner to
the outside of the belt with your right hand. See
fig. 16.
6. Fit the belt cover. See fig. 8 and 10.
7. Lift up and secure the rear section of the cutting
deck.
107 M HD on machines with 17” wheels:
Install
the pins in the third hole from the top. See fig.
13.
107 M HD on machines with 16” wheels:
Install
the pins in the fourth hole from the top. See fig.
13.
121 M: Lift up and install the pins (7:I).
3.3 Installing 107 M
1. Place the cutting deck in position in front of the
machine.
2. Install the following components on both wheel
axles:
Washer (11:B).
Deck arm (11:D).
Washer (11:B).
Circlip (11:A).
3. Install the deck arms in the cutting deck’s front
corners. After tightening, it should be possible
to move the rear section of the cutting deck free-
ly up and down.
4. Suspend the cutting deck in the implement lift-
er. See fig. 14.
3.3.1 Belt, 107 M
The cutting deck’s rear section should rest on the
floor (it should not be lifted or secured).
Install the belt as follows:
1. Set the maximum cutting height.
2. Remove the belt cover. See fig. 10. The number
in the figure indicates the key width.
3. Locate the belt around the machine’s belt pulley
(16:M).
4. Force the belt onto the cutting deck’s belt pul-
ley.
5. Grip the belt tensioners lever with your left
hand. Pull the lever and apply the tensioner to
the outside of the belt with your right hand. See
fig. 16.
6. Fit the belt cover. See fig. 10.
7. Lift up the cutting deck so that it locks in the
catches (12:L).
3.4 Tyre pressure
Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).
3.5 Basic setting
In order for the cutting deck to cut optimally, the
correct basic setting is required. The deck is in the
basic setting when its rear edge is 5 mm above its
front edge. This means that the deck is inclined
forwards.
Carry out basic setting as described below.
3.5.1 Basic setting, 125 Combi Pro, 107 M
HD
The deck is in the basic setting when the actions
under 3.1.1 and 3.2.1 have been carried out.
3.5.2 Basic setting, 107 M, 121 M
See fig. 17 and perform basic setting of 107 M and
121 M as follows:
1. Place the machine on a level floor.
Requirements for floor flatness: ±1 mm/m. No
slope towards a floor drain or similar may occur
in front of or behind the machine.
2. The tyres must have the correct air pressure.
See 3.4.
3. Place the deck in transport position and lay a
plane-parallel plank under the deck.
4. Place a 5 mm tall spacer on the plank under the
rear edge of the cutting deck, and lower the
deck to the working position.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stiga 107M HD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stiga 107M HD in de taal/talen: Engels als bijlage per email.

De handleiding is 0,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info