GB
- 10 - - 11 -
Installation
Connecting the mains power supply lead (see Fig.).
The mains lead consists of a 3-phase cable:
L = phase conductor (usually black, brown or grey)
N = neutral conductor (usually blue)
PE = protective-earth conductor (green/yellow)
If you are in any doubt, identify the conductors using
a voltage tester; then switch off the power again. Con-
nect the phase conductor (L) and neutral conductor (N)
to the terminal block.
Important:
■ Reversing the connections will result in a short-
circuit in the light unit or in your fuse box later on.
In this case, you must identify the individual con-
ductors once again and re-connect them. A mains
switch for switching the unit ON and OFF may of
course be installed in the mains power supply
lead.
Safety Precautions
■ Disconnect the power supply before attempting
any work on the unit.
■ During installation, the electrical wiring being con-
nected must be dead. Therefore, switch off the
power first and use a voltage tester to make sure
the wiring is off circuit.
■ Installing the SensorLight involves work on the
mains voltage supply. This work must therefore
be carried out professionally in accordance with
applicable national wiring regulations and electrical
operating conditions. (
D
-VDE 0100,
A
- ÖVE /
ÖNORM E8001-1,
- SEV 1000)
■ Only use genuine replacement parts.
■ Repairs must only be made by specialist work-
shops.
After the wall mount/ceiling holder has been in-
stalled and the mains connection has been made,
the SensorLight can be used for the first time. When
putting the light into operation manually at the light
switch, it will switch OFF after 10 sec. for the calibra-
tion phase and is then activated for sensor mode.
It is not necessary to operate the light switch a
second time.
Functions
Installation Instructions
Dear Customer,
Congratulations on purchasing your new STEINEL
SensorLight and thank you for the confidence you
have shown in us. You have chosen a pioneering
quality product that has been manufactured, tested
and packed with the greatest care.
Please familiarise yourself with these instructions
before attempting to install the product because
prolonged reliable and trouble-free operation will only
be ensured if it is fitted properly.
We hope your new STEINEL light will bring you
lasting pleasure.
GB
System Components
Wall mount/ceiling mount
HF sensor
Spacer for surface wiring
Oval sealing plug
Oval sealing washer
DIM-level button for installation purposes
Reach setting
Time setting
Light-level setting
Dip switch
(
-) Channel selection
Communication unit (wireless)
(
-) Dimming functions
Snake-eye screws (optional)
Shrouds for partial limiting of the reach
Examples of use
Mains connection cable for concealed wiring
Mains connection cable for surface wiring
Examples of Use
The RS PRO LED S1/S2 IP65 is an efficient light that
controls itself. A high-frequency sensor for detecting
persons, a light sensor for identifying the room's light-
ing situation as well as LEDs requiring hardly any
maintenance provide efficient, instantaneous light. The
facility of 868-MHz wireless communication (channel
selection) allows several lights to be interconnected in
a room, creating a group. Wireless communication to
the next light functions reliably over a distance of 50 m.
All lights then operate with equal rights and act as one
large light.
Principle
The SensorLight is an active motion detector. The
integrated HF-sensor emits high-frequency electro-
magnetic waves (5.8 GHz) and receives their echo.
The sensor detects the change in echo from even
the slightest movement in the light's detection zone.
A microprocessor then triggers the "switch light ON"
command. Detection is possible through doors,
panes of glass or thin walls.
Detection zones for ceiling mounting:
1) Minimum reach (1 m all round)
2) Maximum reach (8 m all round)
Detection zones for wall mounting:
3) Minimum reach (1 m all round)
4) Maximum reach (8 m all round)
Important: Persons or objects moving towards the
light are detected best.
Note:
The high-frequency output of the HF sensor is approx.
1 mW – that's 1000 times less than the transmission
power of a mobile phone or the output of a microwave
oven.
I
II
Install mode
The light features an install mode to
avoid strong glare from the LEDs at
full output during installation.
To select this mode, press button .
The light dims to 10 % output until
button is pressed a second time or
automatically activates the selected
sensor functions after 30 min.
= 30 min install
Twilight setting (response threshold)
Factory setting: 2000 lux
The light's response threshold
can be set to any level from
approx. 2 – 2000 lux.
Control dial set to =
daylight operation (approx. 2000 lux)
Control dial set to =
night-time operation (approx. 2 lux)
2 – 2000 lux
Reach setting (sensitivity)
Factory setting: 8 m
Reach is understood to mean the
diameter of the more or less circular
detection zone produced on the
ground after mounting the Sensor-
Light at a height of 2.5 m.
Control dial set to " · " = min. reach
(approx. diameter 1 m)
Control dial set to + = max. reach
(approx. diameter 8 m)
Control dial set to – = sensor OFF
Motion detection and all other sensor functions are
completely deactivated. In this setting, the light can
be used like a normal light and turned ON and OFF at
the light switch.
You can reduce reach in four directions by fitting the
shrouds provided (see page 5).
Ø 1 m – 8 m
Time setting (switch-OFF delay)
Factory setting: 5 seconds
The light can be be set to stay ON
for any time from approx. 5 sec. to
a maximum of 15 min.
Any movement detected before this
time elapses will re-start the timer.
Note: After the light switches OFF, it takes approx.
1 sec. before it is able to start detecting movement
again. The light will only switch ON in response to
movement once this period has elapsed.
5 sec - 15 min
approx. 1 mW
approx. 1000 mW
10.1
10.2
10.3
10.4
10.5
