593151
8
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
14
The system can be put into
operation once the sensor
has been connected and
installed. Two setting con-
Switch-off delay
(time setting)
The chosen light ‘ON’ time
can be varied continuous-
ly from approx. 8 sec. to a
maximum of 35 min. The
shortest period, approx.
8 sec., is selected by
turning the control fully
clockwise. The longest
period, approx. 35 mins.
is selected by turning the
control fully anticlockwise.
It is recommended to
select the shortest time
for adjusting the detection
zone and for performing
the walk test. Any move-
ment in the detection
zone will re-activate the
time setting.
Twilight setting
(response threshold)
The chosen detector
response threshold can
be adjusted continuously
from approx. 2 lux to 2000
lux. Turning the control
fully clockwise will select
daytime operation at ap-
prox. 2000 lux.
Turned fully anti-clock-
wise, the control is set to
dusk-to-dawn operation
at approx. 2 lux. When
adjusting the detection
zone and for the perform-
ance test in daylight, the
adjusting screw must be
turned fully clockwise.
Functions
8 sec. – 35 min.
2 – 2000 lux
trols are provided on the
bottom of the unit.
Reach adjustment
(s. fi g. page 4)
Reach can be reduced by
tilting (70°) the sensor.
The sensor can be turned
horizontally through 40°
(only with swivel mount) to
align the detection zone
in exactly the way you
require.
The adhesive shrouds
provided may be used
to adjust the sensor‘s
detection angle to suit
individual requirements.
This makes it possible,
for example, to blank out
neighbouring premises
from detection or
specifi cally target paths.
Precision adjustment using shrouds
(s. fi g. page 4)
15
pose. Weather conditions
may affect the way the
motion detector works.
Strong gusts of wind,
snow, rain or hail may
cause the light to come
‘on’ when it is not wanted
because the sensor is
unable to distinguish sud-
den changes of tempera-
ture from sources of heat.
The detector lens may be
cleaned with a damp cloth
if it gets dirty (do not use
cleaning agents).
Operation/Maintenance
The Infrared Sensor is
suitable for switching light
‘on’ and ‘off’ automatically.
The unit is not suitable
for special burglary alarm
systems since it lacks
the tampering protection
prescribed for this pur-
1) e.g. 1-4 x 100 W fi lament bulbs
2) Service load, light of 600 W max. (see Technical specifi cations)
3) IS 2160 connection terminals
4) Indoor switch
5) Indoor series switch, manual, automatic
6) Indoor double-throw switch, automatic, permanent light ‘ON’
Wiring examples
2. Light with neutral conductor
1. Light without neutral conductor
4. Connection to double-throw switch
for permanent light ‘ON’ and automatic
operation
Setting I: automatic operation
Setting II: manual operation for permanent
light ‘ON’
Important: the unit cannot be switched
off, but operated only at settings I and II.
3. Connection using series switch
for manual and automatic operation
GB
8

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Steinel-IS-2160

Zoeken resetten

  • Mijn bewegingsmelder IS2140 werkte na aansluiten. Schakelde na ca 30 sec uit. Daarna lang wachten tot hij bij beweging weer inschakelde. Na verstelling van maan-zon tijd deed hij helemaal niets meer. Wat is de functie van deze draaiknoppen? Gesteld op 8-1-2021 om 19:41

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Steinel IS 2160 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Steinel IS 2160 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info