Handleiding Starkwerk SW 4700 (pagina 17 van 24) (Duits, Engels)

781907

Verklein

Vergroot

Pagina terug

1/24

Pagina verder

Assembly

Fig.3-5

For packaging purposes, your machine

is not fully assembled.

1 Remove the machine from the packaging and place

carefully to one side on the ground.

2 Unscrew the star knob screw (A) and fold the sup-

porting feet down. Re-tighten the star knob screw

(Fig. 3)

3 Place the machine on the feet.

4 Install the handle onto the motor housing using 2

hexagon screws (B) (Fig. 4).

5 Secure the cooling water pump (13) into the pre-

scribed position in the water pan (4)

6 Fill the water pan until the water pump is completely

covered with water. Ensure that the discharge is

sealed securely.

Start-up

On/Off switch (Fig. 4)

To switch on, press “I” on the On/Off switch (16)

Before starting the cutting process, wait until the

cutting wheel reaches its maximum speed and the

cooling water pump (13) has fed the water to the cutting

wheel.

To switch off, press the “0” on the switch (16).

(Fig. 4).

Operation

90° cuts Fig.6-7

1 Loosen the star screw (C)

2 Set the transverse cutting gauge (6) to 90° and re-

tighten the star screw.

3 Tighten the wing screw (D) to x the transverse cut-

ting gauge (6) into position. (Fig.6)

4 Use the handle (11) to push the machine head (1)

backwards.

5 Place the tile on the stop rail (7) on the transverse

cutting gauge.

6 Use the handle (11) to push the machine head (1)

to the required cutting depth and x the machine

head again.

7 Switch on the tile cutter. Attention: Wait until the cool-

ing water has reached the cutting wheel (10).

8 Use the handle (11) to pull the machine head (1)

slowly and evenly forwards through the tile.

9 Switch the cutting wheel off again once you have

nished cutting.

45° diagonal cut (Fig. 8)

1 Set the angled stop (6) to 45°

2 Perform cutting as described above.

45° longitudinal cut (Fig. 9)

1 Loosen the star knob screw (E) on both sides

2 Angle the guide rails (8) 45° to the left on the angle

scale (18).

3 Re-tighten the star knob screw (E) on both sides.

4 Perform cutting as described.

Replacing the diamond cutting wheel (Fig. 10- 12)

Attention! Pull out the mains plug

1 Unscrew the screw (F) and remove the cutting wheel

guard (9). (Fig.10)

2 Attach the Allen key (19) to the motor shaft and hold.

3 Use the spanner (20) to unscrew the ange nuts in

the direction in which the cutting wheel (10) runs.

(Left-handed thread)

4 Remove the outer ange (21) and the cutting wheel

(10).

5 Clean the holding ange carefully before installing

the new cutting wheel.

6 Insert the new cutting wheel in the reverse sequence

and tighten. Attention: Ensure that the cutting wheel

runs in the correct direction!

7 Re-install the cutting wheel guard (9).

Setting the parallel position of the diamond cutting

disc (Fig. 13-15)

If the cut is not straight or the tile breaks along the cut-

ting line, the parallel position of the diamond cutting disc

must be set.

1. At the beginning, the stop rail must be positioned

square to the guide rail. For this, loosen the Allen screws

(A) along the stop rail and align it square with a carpen-

ter’s square or a large tile. In this step, the diamond cut-

ting disc must run along the entire length of the square

or the tile edge. Afterwards, re-tighten the two stop rail

Allen screws (A).

2. Disassemble the length display by removing the two

Phillips screws (B). (Fig. 16)

3. Disassemble the cable retainers (C). (Fig. 17)

4. Slightly loosen two hexagon nuts (D) on each of the

saw unit sides. (Fig. 18, 19)

5. Now the entire saw unit with diamond cutting disc can

be aligned to the stop rail using a carpenter’s square or a

large tile. (Fig. 20)

6. Re-tighten the saw unit’s hexagon nuts and assemble

all machine components. Check it is parallel and carry

out a test cut.

If the test cut is not satisfactory, repeat steps 1-6.

Transport

Attention! Pull out the power plug

To transport the machine, position the machine head to

the front and use the adjustment stops to x it in place.

m Electric connection

Check electric cables regularly for damage. Ensure that

during the check, the connecting cable is not connected

to the mains.

Electric connecting cables must conform to the common

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Starkwerk SW 4700 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info